RESUMEN

Water is an indispensable strategic resource for biological and social development. The problem of oily wastewater pollution originating from oil spillages, industrial discharge and domestic oil pollution has become an extremely serious international challenge. At present, numerous superwetting materials have been applied to effectively separate oil and water. However, most of these materials are difficult to scale and their large-scale application is limited by cost and environmental protection. Herein, a simple, environmentally friendly strategy including sol-gel, freeze-drying and surface hydrophobic modification is presented to fabricate a bamboo cellulose foam with special wetting characteristics. The bamboo cellulose foam is superhydrophobic, with a water contact angle of 160°, and it has the superoleophilic property of instantaneous oil absorption. Owing to the synergistic effect of the three-dimensional network structure of the superhydrophobic bamboo cellulose foam and its hydrophobic composition, it has an excellent oil-absorption performance of 11.5 g/g~37.5 g/g for various types of oil, as well as good recyclability, with an oil (1,2-dichloroethane) absorption capacity of up to 31.5 g/g after 10 cycles. In addition, the prepared cellulose-based foam exhibits an outstanding performance in terms of acid and alkali corrosion resistance. Importantly, owing to bamboo cellulose being a biodegradable, low-cost, natural polymer material that can be easily modified, superhydrophobic/superoleophilic bamboo cellulose foam has great application potential in the field of oily wastewater treatment.

RESUMEN

Intelligent surfaces with controlled wettability have caught much attention in industrial oily wastewater treatment. In this study, a hygro-responsive superhydrophilic/underwater superoleophobic coating was fabricated by the liquid-phase deposition of SiO2 grafted with perfluorooctanoic acid. The wettability of the surface could realize the transformation from superhydrophilicity/underwater superoleophobicity (SHI/USOB) to superhydrophobicity/superoleophilicity (SHB/SOI), both of which exhibited excellent separation performance towards different types of oil-water mixtures with the separation efficiency higher than 99%. Furthermore, the long-chain perfluoroakyl substances on the surface could be decomposed by mixing SiO2 with TiO2 nanoparticles under UV irradiation, which could reduce the pollution to human beings and environment. It is anticipated that the prepared coating with controlled wettability could provide a feasible solution for oil-water separation.

RESUMEN

The unique features of bioresources such as cellulose and bio-wax include renewability, biodegradability, low cost, and abundance on Earth. Therefore, their efficient use is essential for a sustainable economy. Herein, we report a facile method for the surface modification of pretreated cotton with a bio-wax emulsion in water and Fe3O4 nanoparticles to fabricate a green, durable, magnetic, and superhydrophobic/superoleophilic absorbent for the sorption of oil and organic solvents. Magnetic superhydrophobic cotton (MSC) was successfully prepared via a simple two-step dip-coating method without using any toxic organic reagents. The as-prepared MSC was used to selectively absorb various types of oils and organic solvents up to approximately 20-50 times its own weight. Furthermore, it exhibited a stable magnetic responsivity and high reusability in oil/water separation cycles. In addition, the removal and collection of the absorbed oil/organic solvents were easily achieved with distillation and a vacuum air pump. Moreover, the as-prepared MSC was used in a heavy oil/water gravity-separation filter system and in the continuous collection of a light oil from water surfaces using a pump. The proposed concept may provide a green and sustainable strategy for fabricating superhydrophobic/superoleophilic materials for efficient sorption of oils and organic solvents.

Asunto(s)

RESUMEN

The superoleophobic/superhydrophilic material has attracted considerable interest due to the incomparable property of it for the oil-water separation. However, it is a challenge to make the prepared surface superoleophobic and superhydrophilic at the same time since the oleophobic surface tends to repel water. Herein, a hygro-responsive superoleophobic/superhydrophilic coating was fabricated by liquid-phase deposition of TiO2 with perfluorooctanoic acid. The wettability of the coating could complete the transformation from superoleophobicity/superhydrophilicity to superhydrophobicity/superoleophilicity, both of which exhibit excellent selective superwettability under the air, underwater, salt, alkali, and acid conditions. The hygro-responsive coating can separate different types of oil-water mixtures, and the separation efficiency could be over 99% using different capillary forces acting on the oil and water phases before and after wettability transformation. Last but not least, long-chain perfluoroalkyl substances on the coating could be decomposed by UV irradiation, which could reduce the harm to the environment and human beings. It is anticipated that the developed superoleophobic/superhydrophilic coating provides a feasible solution for the application of oil-water separation.

RESUMEN

Oil-water separation using super-wetting and the selective permeability of membranes for oil or water has great ecological and economic significance. We report on the transition of wettability response, from superhydrophilic underwater-superoleophobic to superhydrophobic-superoleophilic state, by nanostructuring stainless steel and copper meshes using ultrashort femtosecond laser pulses. Our approach is environment-friendly, chemical free, and efficient as it exploits the benefit of aging the processed samples in a high vacuum environment. We optimized the laser scanning parameters, mesh pore size, and aging conditions to produce membranes exhibiting an extraordinary separation efficiency of 98% for the oil-water mixture. A variation in the water and oil contact angles for different meshes is presented as a function of the laser scanning speed. Stainless steel meshes with 150 µm pore size and copper meshes with 100 µm pore size have demonstrated an excellent wettability response for oil and water phases. Vacuum aging causes rapid chemisorption of hydrocarbons on laser-structured surfaces in the absence of water molecules, rapidly transforming the wetting state from superhydrophilic to superhydrophobic.

RESUMEN

The current demand for oil/water separation with an efficient, cost-effective, and environmentally friendly method is increasing. A laser-structured superhydrophobic/superoleophilic aluminum was prepared by using a nanosecond laser. The aluminum plate was used for oil/water separation without external force, which can replace the traditional porous materials. The effect of hole diameter and spacing on the effectiveness of oil/water separation is discussed. The results show that the aluminum plate with a hole size of 0.5 mm can be considered a more appropriate choice for the oil/water mixtures with large water content. In addition, complete separation of oil and water can be achieved in the hole spacing range of 1.0-3.0 mm. The oil separation speed can be increased without changing the water permeability by reducing the hole spacing, which is positively related to the hole spacing. Separation efficiencies were tested with various oil/water mixtures. The aluminum plate with a hole size of 0.5 mm can quickly separate the different oil mixtures with less than 50% oil content while achieving an oil separation efficiency of up to 99%. Due to the difference in dynamic viscosity of various oil phases, the separation efficiencies of the petrol, kerosene, and diesel are slightly different but can still be maintained above 99%. The laser-processed aluminum plate has several advantages of high porosity, high surface of superhydrophobic properties, and easy tunable structures. In practical applications, the hole size and the spacing should be appropriately adjusted according to specific conditions, such as different oils, the mixing ratios, etc., to obtain the best separation efficiency and speed.

Asunto(s)

RESUMEN

Superhydrophobic/superoleophilic and reinforced ethyl cellulose (SEC) sponges were prepared by cross-linking EC with epichlorohydrin (ECH) and complexing with silanized carbon nanotubes (Si-CNTs) followed by coating nanosilica on the surface of porous sponges and subsequent modification with hexadecyltrimethoxysilane (HDTMS). These synergistic strategies endowed the SEC sponges with the superhydrophobic/superoleophilic properties (θwater = 158.2°, θoil = 0°, sliding angle = 3°) and outstanding mechanical properties (could bear the pressure of 28.6 kPa without damage). The unique micronanostructures and properties of the porous sponges were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and water contact angle measurements. The as prepared SEC sponges with high mechanical strength were able to collect a wide range of oils and organic solvents with absorption capacity up to 64 times of their own weight. Furthermore, the absorption capacity of the sponges decreased slightly to 86.4% of its initial value after 50 separation cycles, suggesting their excellent recyclable performance. The high efficiency and endurability of the sponges during oil/water separation made them ideal absorbent in oil spillage cleanup.