RESUMEN

The growing concern over low-frequency noise pollution resulting from global industrialization has posed substantial challenges in noise attenuation. However, conventional acoustic metamaterials, with fixed geometries, offer limited flexibility in the frequency range adjustment once constructed. This research unveiled the promising potential of ionic electroactive polymers, particularly ionic polymer-metal composites (IPMCs), as a superior candidate to design tunable acoustic metamaterial due to its bidirectional energy conversion capabilities. The previously perceived limitations of the IPMC, including slow reaction and high energy expenditure, owning to its inherent sluggish intermediary ionic mass transport process, were astutely leveraged to expedite the attenuation of low-frequency sound energy. Both our experimental and simulation results elucidated that the IPMC can generate voltage potentials in response to acoustic pressure at frequencies significantly higher than those previously established. In addition, the peak absorption frequency can be effectively shifted by up to 45.7% with the application of a 4 V voltage. By further integration with a microperforated panel (MPP) structure, the developed metamaterial absorbers can achieve complete sound absorption, which was continuously tunable under minimal voltage stimulation across a wide frequency spectrum. In addition, a microslit structure IPMC metamaterial absorber was designed to realize modulation of the perforation rate, and the absorption peak can be shifted by up to 79.2%. These findings signify a pioneering application of ionic intelligent materials and may pave the way for further innovations of tunable low-frequency acoustic structures, ultimately advancing the pragmatic deployment of both soft intelligent materials and acoustic metamaterials.

RESUMEN

This study aims to investigate the potential of integrating natural biochar (BC) derived from eggshell waste into flexible polyurethane (FPU) foam to enhance its mechanical and acoustic performance. The study explores the impact of incorporating BC at various weight ratios (0.1, 0.3, 0.5, and 0.7 wt. %) on the properties of the FPU foam. Additionally, the effects of modifying the BC with (3-aminopropyl)trimethoxysilane (APTMS) at different ratios (10, 20, and 30 wt. %) and the influence of diverse particle sizes of BC on the thermal, mechanical, and acoustic characteristics of the FPU composite are investigated. The functional groups, morphology, and elemental composition of the developed FPU composites are analyzed using Fourier-transform infrared spectroscopy (FTIR), field-emission scanning electron microscopy (FESEM), and energy-dispersive X-ray (EDX) techniques. Characteristics such as density, gel fraction, and porosity were also assessed. The results reveal that the density of FPU foam increased by 4.32% and 7.83% while the porosity decreased to 50.22% and 47.05% with the addition of 0.1 wt. % of unmodified BC and modified BC with 20 wt. % APTMS, respectively, compared to unfilled FPU. Additionally, the gel fraction of the FPU matrix increases by 1.91% and 3.55% with the inclusion of 0.1 wt. % unmodified BC and modified BC with 20 wt. % APTMS, respectively. Furthermore, TGA analysis revealed that all FPU composites demonstrate improved thermal stability compared to unfilled FPU, reaching a peak value of 312.17°C for the FPU sample incorporating BC modified with 20 wt. % APTMS. Compression strength increased with 0.1 wt. % untreated BC but decreased at higher concentrations. Modifying BC with 20% APTMS resulted in an 8.23% increase in compressive strength compared to unfilled FPU. Acoustic analysis showed that the addition of BC improved absorption, and modified BC enhanced absorption characteristics of FPU, reaching Class D with a 20 mm thickness. BC modified with APTMS further improved acoustic properties compared to the unfilled FPU sample (Class E), with 20% modification showing the best results. These composites present promising materials for sound absorption applications and address environmental issues related to eggshell waste.

RESUMEN

In this study, the loss of quality from the oxidative thermal decomposition of jute fiber was explored during the production of reinforced composite materials. Amino silicone oil was used to modify jute fiber, which was then subjected to thermogravimetric analysis. The modified fiber's thermal decomposition temperature was found to be 271 °C, enhancing the composite's thermal stability. The study also investigated how different jute fiber content affected the mechanical and sound absorption properties of composite materials. Results showed that jute fiber composites had better mechanical properties than pure polypropylene materials, and the average sound absorption coefficient of jute polypropylene composites increased with fiber content. Adding jute fiber to polypropylene effectively improved the sound absorption and noise reduction performance of the material. The average sound absorption coefficient of the composite material at a mass content of 20 wt% was 120 % higher than that of the polypropylene matrix material.

RESUMEN

This study investigates lightweight and efficient candidates for sound absorption to address the growing demand for sustainable and eco-friendly materials in noise attenuation. Juncus effusus (JE) is a natural fiber known for its unique three-dimensional network, providing a viable and sustainable filler for enhanced sound absorption in honeycomb panels. Microperforated-panel (MPP) honeycomb absorbers incorporating JE fillers were fabricated and designed, focusing on optimizing the absorber designs by varying JE filler densities, geometrical arrangements, and MPP parameters. At optimal filling densities, the MPP-type honeycomb structures filled with JE fibers achieved high noise reduction coefficients (NRC) of 0.5 and 0.7 at 20 mm and 50 mm thicknesses, respectively. Using an analytical model and an artificial neural network (ANN) model, the sound absorption characteristics of these absorbers were successfully predicted. This study demonstrates the potential of JE fibers in improving noise mitigation strategies across different industries, offering more sustainable and efficient solutions for construction and transportation.

RESUMEN

Incorporating acoustic and mechanical properties into a single multifunctional structure has attracted considerable attention in engineering. However, effectively integrating these sound absorption properties and damage resistance to achieve multifunctional structural designs remains a great challenge due to imperfect design methods. In this study, the inherent mechanical properties of turtle shells by introducing dissipative pores are leveraged to present a lattice structure that possesses both excellent sound-absorg and high damage-resistant characteristics. To achieve acoustic optimization design, a universal high-fidelity neural network correction model is proposed to address the impedance calculation challenge in complex structures. Building upon this foundation, a multi-cell combination design enables to achieve high absorption through optimization with a low thickness of 50 mm, resulting in average sound absorption coefficients reaching 0.88 and 0.93 within the frequency ranges of 300-600 Hz and 500-1000 Hz, respectively. It is also found that the optimized structures exhibit exceptional damage resistance under varying relative densities via the coupling effect of the shell thickness on the acoustic and mechanical properties. Overall, this work introduces a novel paradigm for designing intricate multifunctional structures with acoustic and mechanical properties while providing valuable inspiration for future research on multifunctional structure design.

RESUMEN

Down-polyethylene film material has been introduced for the first time as an excellent non-frame sound absorber, showing a distinctively outstanding performance. It contains down fiber adjacent to each other without firm connection in between, forming a structure of elastic fiber network. The unique structure has broadband response to sound wave, showing non-synchronous vibration in low and middle frequency and synchronous vibration in middle and high frequency. The broadband resonance in middle and high frequency allows the structure to achieve complete sound absorption in resonance frequency band. Moreover, down-polyethylene film material possesses forced vibration, corresponding sound absorption coefficient has been obtained based on vibration theory. The down-film sound absorption material has the characteristics of light weight, soft, environment-friendly, and has excellent broadband sound absorption performance.

RESUMEN

Various acoustic materials are developed to resolve noise pollution problem in many industries. Especially, materials with porous structure are broadly used to absorb sound energy in civil construction and transportation area. Polyurethane (PU) porous materials possess excellent damping properties, good toughness, and well-developed pore structures, which have a broad application prospect in sound absorption field. This work aims to summarize the recent progress of fabrication and structure for PU porous materials in sound absorption application. The sound absorption mechanisms of porous materials are introduced. Different kinds of structure for typical PU porous materials in sound absorption application are covered and highlighted, which include PU foam, modified PU porous materials, aerogel, templated PU, and special PU porous materials. Finally, the development direction and existing problems of PU material in sound absorption application are briefly prospected. It can be expected that porous PU with high sound absorption coefficient can be obtained by using some facile methods. The design and accurate regulation of porous structures or construction of multilayer sound absorption structure is favorably recommended to fulfill the high demand of industrial and commercial applications in the future work.

Asunto(s)

RESUMEN

The application of Scirpus grossus (SG) fiber as a sound absorber is important to reduce the level of noise affected the physical and mental wellbeing of people. The sound absorption coefficient (SAC) and noise reduction coefficient (NRC) of the SG specimen were evaluated based on a typical model-based design using the data analysis with MATLAB. The results showed that SG specimen with a thickness of 20 mm coated with the perforated aluminum sheet (PAS) compared to that without coating can improve the capability of sound absorption by 14% at the frequency of 4000 Hz. SG specimen coated with PAS that has a NRC value of 0.39 can absorb 39% of sound and thus reflects 61% of sound wave while SG specimen without coating that has a NRC value of 0.23 absorbs 23% of sound and can reflect 77% of sound wave. The sound absorption class of D for SG specimen coated with PAS should be better that of E for SG specimen without coating, which permits us to get better understanding on the applications of SG fiber as a sound adsorber in the future.

RESUMEN

In the present study, the sound absorption performance of inhomogeneous Micro-Perforated Panels (MPPs) with multiple cavities is investigated. Two models, a three-cavity system and a four-cavity system, are proposed and a numerical study is performed using MATLAB. The models are validated through experimental analysis in an impedance tube. The study meticulously varies the geometrical parameters, including pore diameter, thickness of the MPP, perforation ratio, and back-cavity length. It is found that MPPs with a greater number of sub-cavities have a better sound absorption coefficient than two-cavity systems. The results suggest that the back air cavity is predominantly responsible for multiple peaks, ensuring wideband sound absorption. It is also found that smaller perforation ratios for sub-cavities with larger pore diameters improve sound absorption performance in the lower frequency region. The study indicates that a pore diameter of less than 0.5 mm should be used for better sound absorption above the range of 800-850 Hz, and back cavity length has greater control than pore diameter between 850 Hz and 2000 Hz to make the curve smooth with less fluctuation. The findings have significant implications for the design of MPPs for real-world applications.

RESUMEN

New composites made of natural fiber polymers such as wasted date palm surface fiber (DPSF) and pineapple leaf fibers (PALFs) are developed in an attempt to lower the environmental impact worldwide and, at the same time, produce eco-friendly insulation materials. Composite samples of different compositions are obtained using wood adhesive as a binder. Seven samples are prepared: two for the loose natural polymers of PALF and DPSF, two for the composites bound by single materials of PALF and DPSF using wood adhesive as a binder, and three composites of both materials and the binder with different compositions. Sound absorption coefficients (SACs) are obtained for bound and hybrid composite samples for a wide range of frequencies. Flexural moment tests are determined for these composites. A thermogravimetric analysis test (TGA) and the moisture content are obtained for the natural polymers and composites. The results show that the average range of thermal conductivity coefficient is 0.042-0.06 W/(m K), 0.052-0.075 W/(m K), and 0.054-0.07 W/(m K) for the loose fiber polymers, bound composites, and hybrid composites, respectively. The bound composites of DPSF have a very good sound absorption coefficient (>0.5) for almost all frequencies greater than 300 Hz, followed by the hybrid composite ones for frequencies greater than 1000 Hz (SAC > 0.5). The loose fiber polymers of PALF are thermally stable up to 218 °C. Most bound and hybrid composites have a good flexure modulus (6.47-64.16 MPa) and flexure stress (0.43-1.67 Mpa). The loose fiber polymers and bound and hybrid composites have a low moisture content below 4%. These characteristics of the newly developed sustainable and biodegradable fiber polymers and their composites are considered promising thermal insulation and sound absorption materials in replacing synthetic and petrochemical insulation materials in buildings and other engineering applications.

RESUMEN

Sheep farmers are currently facing an oversupply of wool and a lack of willing buyers. Due to low prices, sheep wool is often either dumped, burned, or sent to landfills, which are unsustainable and environmentally unfriendly practices. One potential solution is the utilization of sheep wool fibers in polymer composites. This paper focuses on the study of mechanical vibration damping properties, sound absorption, light transmission, electrical conductivity of epoxy (EP), polyurethane (PU), and polyester (PES) resins, each filled with three different concentrations of sheep wool (i.e., 0%, 3%, and 5% by weight). It can be concluded that the sheep wool content in the polymer composites significantly influenced their physical properties. The impact of light transmission through the tested sheep wool fiber-filled polymer composites on the quality of daylight in a reference room was also mathematically simulated using Wdls 5.0 software.

RESUMEN

In this report, naturally available materials have been utilized in the development of acoustic absorbers. This work presents the study of the effect of oil palm trunks dust (OPTD) loading to the mechanical and acoustical properties of elastomeric thermoplastic polyurethane (TPU). Four composite sheets of 3-mm thickness were prepared by varying the OPTD loadings with 10-40% wt into the polyurethane. Density, modulus elasticity, sound absorption coefficient and sound transmission loss of the samples were measured according to corresponding standards. The OPTD is found to reduce the density of the elastomeric polyurethane and at the same time, it increases the Young's modulus up to 215 MPa. The composite material can be applied as sound absorber panel installed in front of a rigid wall with an air gap. Increasing the air gap, thus lowering the air stiffness, shifts the absorption peak to a lower frequency. With OPTD loadings, the formation of micro-pores in the inner structure helps to improve the peak of sound absorption of the panel at the resonant frequency which can reach above 0.9. As the OPTD loading has effect on density, the effect on the sound transmission loss at the mass-controlled region is also apparent.

RESUMEN

Porous materials with sound absorption and load-bearing capabilities are in demand in engineering fields like aviation and rail transportation. However, achieving both properties simultaneously is challenging due to the trade-off between interconnected pores for sound absorption and mechanical strength. Inspired by quilling art, a novel design using spiral material formed by rolling planar materials into helical structures is proposed. Experimental results show high structural strength through self-locking mechanisms, while double porosities from interlayer spiral slits and aligned submillimeter pores provide excellent sound absorption. These spiral sheets surpass foam aluminum in specific strength (up to 5.1 MPa) and approach aerogels in sound absorption (average coefficient of 0.93 within 0-6400 Hz). With its adaptability to various planar materials, this spiral design allows for hybrid combinations of different materials for multi-functionality, paving the way for designing advanced, lightweight porous materials for broad applications.

RESUMEN

This paper reports an environment-friendly biobased foam made with cellulose nanofiber (CNF) and a biobased hyperbranched crosslinker, glycerol succinic anhydride (GSA). As a biobased hyperbranched crosslinker, carboxyl-terminated GSA is synthesized through a straightforward esterification process involving glycerol and succinic anhydride. The GSA-crosslinked CNF (GSA/CNF) foam is prepared using a facile, sustainable, cost-effective, and efficient solvent-exchange method. The resulting foam exhibits notable characteristics, including improved dimensional stability, remarkably low density (13.41 mg/cm3) with high porosity (>99 %), and exceptional compressive strength (494 kPa) and modulus (452 kPa). Further, the foam offers outstanding sound absorption capabilities with a coefficient of 0.986 at 2 kHz and remarkably low thermal conductivity (30.18 mW/mK), significantly lower than commonly used and reported porous materials, indicating its potential as an efficient, environmentally friendly sound absorption and thermal insulation material.

RESUMEN

Lightweight, porous cellulose foam is an attractive alternative to traditional petroleum-based products, but the intrinsic flammability impedes its use in construction. Herein, an environmentally friendly strategy for scalable fabrication of flame-retardant bamboo pulp foam (BPF) using a foam-forming technique followed by low-cost ambient drying is reported. In the process, a hierarchical structure of halloysite nanotubes (HNT) was decorated onto bamboo pulp fibers through layer-by-layer assembling of chitosan (CS) and phytic acid (PA). This modification retained the highly porous microcellular structure of the resultant BPF (92 %-98 %). It improved its compressive strength by 228.01 % at 50 % strain, endowing this foam with desired thermal insulation properties and sound absorption coefficient comparable to commercial products. More importantly, this foam possessed exceptional flame retardancy (47.05 % reduction in the total heat release and 95.24 % reduction in the total smoke production) in cone calorimetry, and it showed excellent extinguishing performance, indicating considerably enhanced fire safety. These encouraging results suggest that the flame retardant BPF has the potential to serve as a renewable and cost-effective alternative to traditional foam for applications in acoustic and thermal insulation.

Asunto(s)

RESUMEN

The reduction of noises, achieved through absorption, is of paramount importance to the well-being of both humans and machines. Lattice structures, defined as architectured porous solids arranged in repeating patterns, are emerging as advanced sound-absorbing materials. Their immense design freedom allows for customizable pore morphology and interconnectivity, enabling the design of specific absorption properties. Thus far, the sound absorption performance of various types of lattice structures are studied and they demonstrated favorable properties compared to conventional materials. Herein, this review gives a thorough overview on the current research status, and characterizations for lattice structures in terms of acoustics is proposed. Till date, there are four main sound absorption mechanisms associated with lattice structures. Despite their complexity, lattice structures can be accurately modelled using acoustical impedance models that focus on critical acoustical geometries. Four defining features: morphology, relative density, cell size, and number of cells, have significant influences on the acoustical geometries and hence sound wave dissipation within the lattice. Drawing upon their structural-property relationships, a classification of lattice structures into three distinct types in terms of acoustics is proposed. It is proposed that future attentions can be placed on new design concepts, advanced materials selections, and multifunctionalities.

RESUMEN

To reduce electromagnetic interference and noise pollution within communication base stations and servers, it is necessary for electromagnetic wave absorption (EWA) materials to transition from coating to multifunctional devices. Up to now, the stable and effective integration of multiple functions into one material by a simple method has remained a large challenge. Herein, a foam-type microwave absorption device assembled with multicomponent organic matter and graphite powder is synthesized by a universal combination process. Melamine and phenolic aldehyde amine work as the skeleton and cementing compound, respectively, in which graphite is embedded in the cementing compound interconnected into the mesoscopic 3D electric conductive and heat conductive network. Interestingly, the prepared flexible graphite/melamine foam (CMF) delivers a great EWA performance, with a great effective absorption bandwidth of 9.8 GHz, ultrathin thickness of 2.60 mm, and a strong absorption reflection loss of -41.7 dB. Moreover, the CMF possesses porosity and flexibility, endowing it with sound absorption ability. The CMF is unique in its integration of EWA, heat conduction, sound absorption, and mechanical robustness, as well as its cost-effective and scalable manufacturing. These attributes make CMF promising as a multifunctional device widely used in communication base stations, servers, and chips protection.

RESUMEN

To make the sound absorber easy to fabricate and convenient for practical application, a modular composable acoustic metamaterial with multiple nonunique chambers (MCAM-MNCs) was proposed and investigated, which was divided into a front panel with the same perforated apertures and a rear chamber with a nonunique grouped cavity. Through the acoustic finite element simulation, the parametric studies of the diameter of aperture d, depth of chamber T0, and thickness of panel t0 were conducted, which could tune the sound absorption performances of MCAM-MNCs-1 and MCAM-MNCs-2 for the expected noise reduction effect. The effective sound absorption band of MCAM-MNCs-1 was 556 Hz (773-1329 Hz), 456 Hz (646-1102 Hz), and 387 Hz (564-951 Hz) for T = 30 mm, T = 40 mm, and T = 50 mm, respectively, and the corresponding average sound absorption coefficient was 0.8696, 0.8854, and 0.8916, accordingly, which exhibited excellent noise attenuation performance. The sound absorption mechanism of MCAM-MNCs was investigated by the distributions of the total sound energy density (TSED). The components used to assemble the MCAM-MNCs sample were fabricated by additive manufacturing, and its actual sound absorption coefficients were tested according to the transfer matrix method, which demonstrated its feasibility and promoted its actual application.

RESUMEN

Cellulose-based foams present a high potential for noise insulation applications. These materials are bio-degradable, eco-friendly by both embedded components and manufacturing process, have low density and high porosity, and are able to provide good noise insulation characteristics compared with available petroleum-based foams currently used on a large scale. This paper presents the results of some investigations performed by the authors in order to improve the functional characteristics in terms of free surface wettability and structural integrity. Native xylan and xylan-based derivatives (in terms of acetylated and hydrophobized xylan) were taken into account for surface treatment of cellulose foams, suggesting that hemicelluloses represent by-products of pulp and paper industry, and xylan polysaccharides are the most abundant hemicelluloses type. The investigations were mainly conducted in order to evaluate the level to which surface treatments have affected the noise insulation properties of basic cellulose foams. The results indicate that surface treatments with xylan derivatives have slowly affected the soundproofing characteristics of foams, but these clearly have to be taken into account because of their high decrease in wettability level and improving structural integrity.

RESUMEN

Environmental noise pollution is a growing challenge worldwide, necessitating effective sound absorption strategies to improve acoustic environments. Materials that draw inspiration from nature's structural design principles can provide enhanced functionalities. Wood exhibits an intricate multi-scale porous architecture that can dissipate acoustic energy. This study investigates a biomimetic sound-absorbing structure composed of hierarchical pores inspired by the vascular networks within wood cells. The perforated resonators induce complementary frequency responses and porous propagation effects for broadband attenuation. Samples were fabricated using 3D printing for systematic testing. The pore size, porosity, number of layers, and order of the layers were controlled as experimental variables. Acoustic impedance tube characterization demonstrated that optimizing these architectural parameters enables absorption coefficients approaching unity across a broad frequency range. The tuned multi-layer porous architectures outperformed single pore baselines, achieving up to a 25-35% increase in the average absorption. The bio-inspired coupled pore designs also exhibited a 95% broader working bandwidth. These enhancements result from the increased viscous losses and tailored impedance matching generated by the hierarchical porosity. This work elucidates structure-property guidelines for designing biomimetic acoustic metamaterials derived from the porous morphology of wood. The results show significant promise for leveraging such multi-scale cellular geometries in future materials and devices for noise control and dissipative engineering applications across diverse sectors.