RESUMEN
Solvent additives with a high boiling point (BP) and low vapor pressure (VP) have formed a key handle for improving the performance of organic solar cells (OSCs). However, it is not always clear whether they remain in the active-layer film after deposition, which can negatively affect the reproducibility and stability of OSCs. In this study, an easily removable solvent additive (4-chloro-2-fluoroiodobenzene (CFIB)) with a low BP and high VP is introduced, behaving like volatile solid additives that can be completely removed during the device fabrication process. In-depth studies of CFIB addition into the D18-Cl donor and N3 acceptor validate its dominant non-covalent intermolecular interactions with N3 through effective electrostatic interactions. Such phenomena improve charge dynamics and kinetics by optimizing the morphology, leading to enhanced performance of D18-Cl:N3-based devices with a power conversion efficiency of 18.54%. The CFIB-treated device exhibits exceptional thermal stability (T80 lifetime = 120 h) at 85 °C compared with the CFIB-free device, because of its morphological robustness by evolving no residual CFIB in the film. The CFIB features a combination of advantages of solvent (easy application) and solid (high volatility) additives, demonstrating its great potential use in the commercial mass production of OSCs.
RESUMEN
The low crystallinity of the perovskite layers and many defects at grain boundaries within the bulk phase and at interfaces are considered huge barriers to the attainment of high performance and stability in perovskite solar cells (PSCs). Herein, a robust photoelectric imidazole-linked porphyrin-based covalent organic framework (PyPor-COF) is introduced to precisely control the perovskite crystallization process and effectively passivate defects at grain boundaries through a sequential deposition method. The 1D porous channels, abundant active sites, and high crystallization orientation of PyPor-COF offer advantages for regulating the crystallization of PbI2 and eliminating defects. Moreover, the intrinsic electronic characteristics of PyPor-COF endow a more closely matched energy level arrangement within the perovskite layer, which promotes charge transport and thereby suppresses the recombination of photogenerated carriers. The champion PSCs containing PyPor-COF achieved power conversion efficiencies of 24.10% (0.09 cm2) and 20.81% (1.0 cm2), respectively. The unpackaged optimized device is able to maintain its initial efficiency of 80.39% even after being exposed to air for 2000 h. The device also exhibits excellent heating stability and light stability. This work gives a new impetus to the development of highly efficient and stable PSCs via employing COFs.
RESUMEN
Quasi-two-dimensional (Q-2D) perovskites show great potential in the field of photonic and optoelectronic device applications. However, defects and local lattice dislocation still limit performance and stability improvement by nonradiative recombination, unpreferred phase distribution, and unbonded amines. Here, a low-temperature synergistic strategy for both reconstructing and solidifying the perovskite top and buried interface is developed. By post-treating the 1,4-phenylenedimethanammonium (PDMA) based (PDMA)MA4Pb5I16 films with cesium acetate (CsAc) before thermal annealing, a condensation reaction between R-COO- and -NH2 and ion exchange between Cs+ and MA+ occur. It converts the unbonded amines to amides and passivates uncoordinated Pb2+. Meanwhile, it adjusts film composition and improves the phase distribution without changing the out-of-plane grain orientation. Consequently, performance of 18.1% and much-enhanced stability (e.g., stability for photo-oxygen increased over 10 times, light-thermal for T90 over 4 times, and reverse bias over 3 times) of (PDMA)MA4Pb5I16 perovskite solar cells are demonstrated.
RESUMEN
Tuning the strength of intramolecular electric field (IEF) in conjugated molecules has emerged as an effective approach to boost charge transfer. While direction manipulation of IEF would be a potential way that is still unclear. Here, we leverage the control of peripheral substituents of conjugated phthalocyanines to chemically tune the spatial orientation of IEF. By analyzing the spatial swing of side chains using the Kolmogorov-Arnold representation and least squares algorithm, a comprehensive mathematical-physical model has been established. This model enables rapid evaluation of the IEF and maximum hole transport performance induced by spatial swings. The champion phthalocyanine as dopant-free hole transport material in perovskite solar cell realizes a record performance of 23.41%. Greatly device stability is also exhibited. This work affords a new way to enhance hole transport capabilities of conjugated molecules by optimizing their IEF vector for photovoltaic devices.
RESUMEN
This study puts forth a novel terminal group design to develop medium-bandgap Y-series acceptors beyond conventional side-chain engineering. We focused on the strategical integration of an electron-donating methoxy group and an electron-withdrawing halogen atom at benzene-fused terminal groups. This combination precisely modulated the dipole moment and electron density of terminal groups, effectively attenuating intramolecular charge transfer effect, and widening the bandgap of acceptors. The incorporation of these terminal groups yielded two asymmetric acceptors, named BTP-2FClO and BTP-2FBrO, both of which exhibited open-circuit voltage (VOC) as high as 0.96 V in binary devices, representing the highest VOCs among the asymmetric Y-series small molecule acceptors. More importantly, both BTP-2FClO and BTP-2FBrO exhibit modest aggregation behaviors and molecular crystallinity, making them suitable as a third component to mitigate excess aggregation of the PM6: BTP-eC9 blend and optimize the devices' morphology. As a result, the optimized BTP-2FClO-based ternary organic solar cells (OSCs) achieved a remarkable power conversion efficiency (PCE) of 19.34%, positioning it among the highest-performing OSCs. Our study highlights the molecular design importance on manipulating dipole moments and electron density in developing medium-bandgap acceptors, and offers a highly efficient third component for high-performance ternary OSCs.
RESUMEN
In order to enhance the overall efficiency of colloidal quantum dots solar cells, it is crucial to suppress the recombination of charge carriers and minimize energy loss at the interfaces between the transparent electrode, electron transport layer (ETL), and colloidal quantum dots (CQDs) light-absorbing material. In the current study, ZnO/SrTiO3 (STO), ZnO/WO3 (TO), and ZnO/Zn2SnO4 (ZTO) bilayers are introduced as an ETL using a spin-coating technique. The ZTO interlayer exhibits a smoother surface with a root-mean-square (RMS) value of ≈ 3.28 nm compared to STO and TO interlayers, which enables it to cover the surface of the ITO/ZnO substrate entirely and helps to prevent direct contact between the CQDs absorber layer and the ITO/ZnO substrate, thereby effectively preventing efficient charge recombination at the interfaces of the ETL/CQDs. Furthermore, the ZTO interlayer possesses superior electron mobility, a higher visible light transmission, and a suitable energy band structure compared to STO and TO. These characteristics are advantageous for extracting charge carriers and facilitating electron transport. The PbS CQDs solar cell based on the ITO/ZnO/ZTO/PbS-FABr/PbS-EDT/NiO/Au device configuration exhibits the highest efficiency of 15.28%, which is significantly superior than the ITO/ZnO/PbS-FABr/PbS-EDT/NiO/Au solar cell device (PCE = 14.38%). This study is anticipated to offer a practical approach to develop ultrathin and compact ETL for highly efficient CQDSCs.
RESUMEN
Perovskite solar cells (PSCs) are considered the most promising photovoltaic devices to replace silicon-based solar cells because of their low preparation cost and high photoelectric conversion efficiency (PCE). Reducing defects in perovskite films is an effective means to improve the efficiency of PSCs. In this paper, a lead chelator was selected and mixed into hole transport layers (HTLs) to design and prepare mesoporous PSCs with the structure of ITO/PTAA(BCP)/Al2O3/PVK/PCBM/BCP/Ag, and its modification effect on the buried interface at the bottom of the perovskite layer in the mesoporous structure was explored. The experimental results show that in the presence of mesoporous alumina, the lead chelator can still play a role in modifying the bottom of the perovskite film. The use of lead chelator as passivation material added to the HTL can effectively reduce the residue of dimethyl sulfoxide (DMSO) and decrease the defects at the bottom of the perovskite film, which dramatically improves the device performance. The PCE of the device is increased from 18.03% to 20.78%, which is an increase of 15%. The work in this paper provides an effective method to enhance the performance of PSCs.
RESUMEN
Wide-bandgap (WBG) perovskite has demonstrated great potential in perovskite-based tandem solar cells. The power conversion efficiency (PCE) of such devices has surpassed 34%, signifying a new era for renewable energy development. However, the ion migration reduces the stability and hinders the commercialization, which is yet to be resolved despite many attempts. A big step forward has now been achieved by the simulation method. The detailed thermodynamics and kinetics of the migration process have been revealed for the first time. The stability has been enhanced by more than 100% via the heterojunction layer on top of the WBG perovskite film, which provided extra bonding for kinetic protection. Hopefully, these discoveries will open a new gate for WBG perovskite research and accelerate the application of perovskite-based tandem solar cells.
RESUMEN
Antimony selenosulfide, denoted as Sb2(S,Se)3, has garnered attention as an eco-friendly semiconductor candidate for thin-film photovoltaics due to its light-absorbing properties. The power conversion efficiency (PCE) of Sb2(S,Se)3 solar cells has recently increased to 10.75%, but significant challenges persist, particularly in the areas of open-circuit voltage (Voc) losses and fill factor (FF) losses. This study delves into the theoretical relationship between Voc and FF, revealing that, under conditions of low Voc and FF, internal resistance has a more pronounced effect on FF compared to non-radiative recombination. To address Voc and FF losses effectively, a phased optimization strategy was devised and implemented, paving the way for Sb2(S,Se)3 solar cells with PCEs exceeding 20%. By optimizing internal resistance, the FF loss was reduced from 10.79% to 2.80%, increasing the PCE to 12.57%. Subsequently, modifying the band level at the interface resulted in an 18.75% increase in Voc, pushing the PCE above 15%. Furthermore, minimizing interface recombination reduced Voc loss to 0.45 V and FF loss to 0.96%, enabling the PCE to surpass 20%. Finally, by augmenting the absorber layer thickness to 600 nm, we fully utilized the light absorption potential of Sb2(S,Se)3, achieving an unprecedented PCE of 26.77%. This study pinpoints the key factors affecting Voc and FF losses in Sb2(S,Se)3 solar cells and outlines an optimization pathway that markedly improves device efficiency, providing a valuable reference for further development of high-performance photovoltaic applications.
RESUMEN
A two-dimensional (2D) conjugated microporous polymer with a structure of 2D nanosheets has been synthesized. Theoretical calculations and experimental results reveal that the Fermi level of this 2D polymer aligns well with perovskite absorber, and its conduction band is high enough to block electron transport to the anode. This 2D polymer is used to modify the hole transport layer, significantly improving its photoelectric properties, including enhanced hole mobility, matched energy level, and reduced recombination. Furthermore, the 2D polymer exhibits a mesoporous structure, allowing perovskite to fill into its loose framework, increasing the hole export area and providing a large hole transport flux. As a result, the efficiency of inverted perovskite solar cells enhances to 24.64% from 21.17% of control device without 2D conjugated microporous polymer. Given that this material can be synthesized on a large scale, this work has significant implications for the future development of 2D polymers in perovskite solar cells, potentially accelerating industrialization.
RESUMEN
In this study, a series of dopant-free, low-cost hole-transporting materials (HTMs) based on triphenylamine-functionalized azadipyrromethene dyes 1-3 (TPA-ADPs 1-3) were designed and synthesized. The properties of these new HTMs were investigated by optical spectroscopy, cyclic voltammetry, thermogravimetric analysis, differential scanning calorimetric, atomic force microscopy, and X-ray diffraction, as well as theoretical calculations. The results indicated that the TPA-ADPs 1-3 presented well-matched energy levels with perovskite, higher hole mobility, as well as more effective defect passivation at the perovskite/HTM interface by the coordination interaction between the ADP moiety and the undercoordinated Pb2+. The n-i-p perovskite solar cells (PSCs) employing HTMs 1-3 as well as doped Spiro-OMeTAD were fabricated and characterized. The TPA-ADP 1-based PSCs exhibited the best performance with a champion power conversion efficiency (PCE) of 22.13% and an fill factor of 0.81, which was superior to that of the devices based on the doped Spiro-OMeTAD. Long-term device performance studies indicated that the TPA-ADP 1-based PSCs maintained 80% of the initial PCE after 1800 h of storage in the ambient condition of 40-60% RH, which was also higher than the stability of doped Spiro-OMeTAD-based devices under the same conditions.
RESUMEN
Vapor-deposited inverted perovskite solar cells utilizing self-assembled monolayer (SAM) as hole transport material have gained significant attention for their high efficiencies and compatibility with silicon/perovskite monolithic tandem devices. However, as a small molecule, the SAM layer suffers low thermal tolerance in comparison with other metal oxide or polymers, rendering poor efficiency in solar device with high-temperature (> 160 °C) fabricating procedures. In this study, a dual modification approach involving AlOx and F-doped phenyltrimethylammonium bromide (F-PTABr) layers is introduced to enhance the buried interface. The AlOx dielectric layer improves the interface contact and prevents the upward diffusion of SAM molecules during the vapor-solid reaction at 170 °C, while the F-PTABr layer regulates crystal growth and reduces the interfacial defects. As a result, the AlOx/F-PTABr-treated perovskite film exhibits a homogeneous, pinhole-free morphology with improved crystal quality compared to the control films. This leads to a champion power conversion efficiency of 21.53% for the inverted perovskite solar cells. Moreover, the encapsulated devices maintained 90% of the initial efficiency after 600 h of ageing at 85 °C in air, demonstrating promising potential for silicon/perovskite tandem application.
RESUMEN
Antimony selenosulfide (Sb2(S,Se)3) has obtained widespread concern for photovoltaic applications as a light absorber due to superior photoelectric features. Accordingly, various deposition technologies have been developed in recent years, especially hydrothermal deposition method, which has achieved a great success. However, device performances are limited with severe carrier recombination, relating to the quality of absorber and interfaces. Herein, bulk and interface defects are simultaneously suppressed by regulating heterogeneous nucleation kinetics with barium dibromide (BaBr2) introduction. In details, the Br adsorbs and dopes on the polar planes of cadmium sulfide (CdS) buffer layer, promoting the exposure of nonpolar planes of CdS, which facilitates the favorable growth of [hk1]-Sb2(S,Se)3 films possessing superior crystallinity and small interface defects. Additionally, the Se/S ratio is increased due to the replacement of S/Se by Br, causing a downshift of the Fermi levels with a benign band alignment and a shallow-level defect. Moreover, Ba2+ is located at grain boundaries by coordination with S and Se ions, passivating grain boundary defects. Consequently, the efficiency is increased from 7.70% to 10.12%. This work opens an avenue towards regulating the heterogeneous nucleation kinetics of Sb2(S,Se)3 film deposited via hydrothermal deposition approach to optimize its crystalline orientation and defect features.
RESUMEN
The all-inorganic CsPbBr3 perovskite solar cells exhibit excellent stability against humidity and thermal conditions as well as relatively low production cost, rendering them a gradually emerging research hot spot in the field of photovoltaics. However, the absence of a hole transport layer (HTL) in its common structure and the substantial energy level difference of up to 0.6 eV between the highest occupied molecular orbital (HOMO) level of CsPbBr3 and the work function of the carbon electrode have emerged as the primary factor limiting the improvement of its power conversion efficiency (PCE). In this work, the monomer 2,5-dibromo-3,4-ethylenedioxythiophene (DBEDOT) is spin-coated onto the surface of the CsPbBr3 film directly and then subjected to annealing; DBEDOT undergoes in situ polymerization to form poly(3,4-ethylenedioxythiophene) (PEDOT), which aims to ameliorate the issue of excessive energy level difference between CsPbBr3 and the carbon electrode, and to facilitate the extraction and transport efficiency of holes between the CsPbBr3 perovskite and the carbon electrode. Compared to the pristine device, the PCE of the device based on in situ polymerization is enhanced and achieves a maximum efficiency of 9.81%. Furthermore, the unencapsulated devices based on in situ polymerization maintain 95.9% of their original efficiency after 40 days of stability testing.
RESUMEN
To seek an earth-abundant and environmentally friendly absorber for thin-film solar cells, Cu3PSe4 is investigated by first-principles calculations and device simulations. We demonstrate that the compound has a suitable band gap width of 1.3 eV as well as a high sunlight absorption coefficient. However, drawbacks like small electron affinity, high hole concentration, large lattice mismatch with CdS, etc., are revealed, which may degrade the photovoltaic performance. To address those shortcomings, we propose (1) to optimize the carrier concentration by preparing the samples at low temperature and under a Cu-rich environment, (2) to replace the CdS buffer layer by a more suitable wide-gap semiconductor with smaller lattice mismatch, and (3) that the selected buffer layer should have small electron affinity in order to reduce the open-circuit voltage losses. After implementation of these optimization approaches, the device simulations demonstrate that the power conversion efficiency reaches 17.7% for a solar cell with the configuration Mo/Cu3PSe4/WS2/n-ZnO. The combination of first-principles calculations at the atomistic level and device simulations at the macroscopic level provides an appropriate approach to design ideal solar cells.
RESUMEN
Semitransparent solar cells are attracting attention not only for their visual effects but also for their ability to effectively utilize solar energy. Here, we demonstrate a translucent solar cell composed of bis(trifluoromethane sulfonyl)-amide (TFSA)-doped graphene (Gr), graphene quantum dots (GQDs), and LaVO3. By introducing a GQDs intermediate layer at the TFSA-Gr/LaVO3 interface, we can improve efficiency by preventing carrier recombination and promoting charge collection/separation in the device. As a result, the efficiency of the GQDs-based solar cell was 4.35%, which was higher than the 3.52% of the device without GQDs. Furthermore, the average visible transmittance of the device is 28%, making it suitable for translucent solar cells. The Al reflective mirror-based system improved the power conversion efficiency (PCE) by approximately 7% compared to a device without a mirror. Additionally, the thermal stability of the device remains at 90% even after 2000 h under an environment with a temperature of 60°C and 40% relative humidity. These results suggest that TFSA-Gr/GQDs/LaVO3-based cells have a high potential for practical use as a next-generation translucent solar energy power source.
RESUMEN
Traditionally used phenylethylamine iodide (PEAI) and its derivatives, such as ortho-fluorine o-F-PEAI, in interfacial modification, are beneficial for perovskite solar cell (PSC) efficiency but vulnerable to heat stability above 85 °C due to ion migration. To address this issue, we propose a composite interface modification layer incorporating the discotic liquid crystal 2,3,6,7,10,11-hexa(pentoxy)triphenylene (HAT5) into o-F-PEAI. The triphenyl core in HAT5 promotes π-π stacking self-assembly and enhances its interaction with o-F-PEAI, forming an oriented columnar phase that improves hole extraction along the one-dimensional direction. HAT5 repairs structural defects in the interfacial layer and retains the layered structure to inhibit ion migration after annealing. Ultimately, our approach increases the efficiency of solar cells from 23.36% to 25.02%. The thermal stability of the devices retains 80.1% of their initial efficiency after aging at 85 °C for 1008 hours without encapsulation. Moreover, the optimized PSCs maintained their initial efficiency of 82.4% after aging under one sunlight exposure for 1008 hours. This study provides a novel strategy using composite materials for interface modification to enhance the thermal and light stability of semiconductor devices.
RESUMEN
The interfacial management in perovskite solar cells (PSCs), including mitigating the carrier transport barrier and suppressing non-radiative recombination, still remains a significant challenge for efficiency and stability enhancement. Herein, by screening a family of fluorine (F) terminated dual-site organic dipole molecules, the study aims to gain insight into the molecular dipole array toward tunable interfacial field. Both experimental and theoretical results reveal that these functional interfacial dipole molecules can effectively anchor on perovskite surface through Lewis acid-base interaction. In addition, the tailored side-chain with terminated F atoms allows for altering and constructing a well matched perovskite/Spiro-OMeTAD interfacial contact. As a result, the inserting dual-site organic dipole array effectively modulates the interface to deliver a gradient energy level alignment, facilitating carrier extraction and transport. The optimal dual-site dipole trifluoro-methanesulfonamide mediated N-i-P PSCs achieve the highest efficiency of 25.47%, together with enhanced operational stability under 1000 h of the simulated 1-sun illumination exposure. These findings are believed to provide insight into the design of dual-site molecular dipole with sufficient interfacial tunability for perovskite-based optoelectronic devices.
RESUMEN
Fullerene-based derivatives are frequently used as electron transport materials (ETMs) and interface buffers for perovskite solar cells (PSCs) due to their excellent properties, including high electron affinity and mobility, low recombination energy, tunable energy levels, and solution processability. However, significant challenges arise because fullerene derivatives tend to aggregate and dimerize, which reduces exciton dissociation and charge transport capacity. Additionally, their chemical compatibility with perovskite absorbers facilitates halide diffusion and degradation of PSCs. This overlap causes delamination and dissolution during device fabrication, hindering the performance enhancement of fullerene-based PSCs. To address these issues, researchers have developed cross-linkable fullerene materials. These materials have been shown to not only significantly improve the power conversion efficiency (PCE) of PSCs but also effectively enhance the device stability. In this review, we summarized recent research progress on cross-linkable fullerene derivatives as ETMs for PSCs. We systematically analyze the impact of these cross-linked ETMs on device performance and long-term stability, focusing on their molecular structures and working mechanisms. Finally, we discuss the future challenges that need to be overcome to advance the application of cross-linkable fullerene materials in PSCs.
RESUMEN
Nitrogen-rich heterocyclic frameworks have attracted enormous interest in organic chemistry and materials science. However, their potential for developing photoluminescent materials remains underexplored due to their relatively low molecular stabilities. In this work, two tricyclic fused nitrogen-rich fluorescent heterocycles were synthesized and characterized. The photophysical properties of the synthesized 4 and 5 were investigated through theoretical and experimental studies. In addition, their physicochemical and energetic properties and the performance as an additive to the perovskite absorption layer of the perovskite solar cell were also studied.