RESUMEN

Infrared detectors have broad application prospects in the fields of detection and communication. Using ideal materials and good device structure is crucial for achieving high-performance infrared detectors. Here, we utilized black phosphorus (BP) and single-walled carbon nanotube (SWCNT) films to construct a vertical van der Waals heterostructure, resulting in high-performance photovoltaic infrared detectors. In the device, a strong built-in electric field was formed in the heterojunction with a favored energy-band matching between the BP and the SWCNT, which caused a good photovoltaic effect. The fabricated devices exhibited a diode-like rectification behavior in the dark, which had a high rectification ratio up to a magnitude of 104 and a low ideal factor of 1.4. Under 1550 nm wavelength illumination, the 2D BP/SWCNT film photodetector demonstrated an open-circuit voltage of 0.34 V, a large external power conversion efficiency (η) of 7.5% and a high specific detectivity (D*) of 3.1 × 109 Jones. This external η was the highest among those for the photovoltaic devices fabricated with the SWCNTs or the heterostructures based on 2D materials and the obtained D* was also higher than those for most of the infrared detectors based on 2D materials or carbon materials. This work showcases the application potential of BP and SWCNTs in the detection field.

RESUMEN

The incorporation of p-type functionalized carbon nanohorns (CNHs) in perovskite solar cells (PSCs) and their comparison with p-type functionalized single- and double-walled carbon nanotubes (SWCNTs and DWCNTs) are reported in this study for the first time. These p-type functionalized carbon nanomaterial (CNM) derivatives were successfully synthesized by [2 + 1] cycloaddition reaction with nitrenes formed from triphenylamine (TPA) and 9-phenyl carbazole (Cz)-based azides, yielding CNHs-TPA, CNHs-Cz, SWCNTs-Cz, SWCNTs-TPA, DWCNTs-TPA, and DWCNTs-Cz. These six novel CNMs were incorporated into the spiro-OMeTAD-based hole transport layer (HTL) to evaluate their impact on regular mesoporous PSCs. The photovoltaic results indicate that all p-type functionalized CNMs significantly improve the power conversion efficiency (PCE), mainly by enhancing the short-circuit current density (Jsc) and fill factor (FF). TPA-functionalized derivatives increased the PCE by 12-17% compared to the control device without CNMs, while Cz-functionalized derivatives resulted in a PCE increase of 4-8%. Devices prepared with p-type functionalized CNHs exhibited a slightly better PCE compared with those based on SWCNTs and DWCNTs derivatives. The increase in hole mobility of spiro-OMeTAD, additional p-type doping, better energy alignment with the perovskite layer, and enhanced morphology and contact interface play important roles in enhancing the performance of the device. Furthermore, the incorporation of p-type functionalized CNMs into the spiro-OMeTAD layer increased device stability by improving the hydrophobicity of the layer and enhancing the hole transport across the MAPI/spiro-OMeTAD interface. After 28 days under ambient conditions and darkness, TPA-functionalized CNMs maintained the performance of the device by over 90%, while Cz-functionalized CNMs preserved it between 75 and 85%.

RESUMEN

The internalization of near-infrared (NIR) optical nanoprobes in photosynthetic microbes can be exploited for applications ranging from energy conversion to biomolecule delivery. However, the intrinsic, species-dependent properties of microbial cell walls, including their surface charge density, composition, thickness, and elasticity, can severely impact nanoprobe uptake and affect the cellular response. An examination of the interaction of the optical nanoprobe in various species and its impact on cell viability is, therefore, imperative for the development of new imaging technologies. Herein, we extend the technology recently developed for internalizing fluorescent single-walled carbon nanotubes (SWCNTs) in prokaryotes, specifically unicellular Synechocystis sp. PCC 6803, to a filamentous cyanobacterial strain, Nostoc punctiforme. Using a combination of NIR fluorescence, scanning electron microscopy (SEM), and Raman spectroscopy, we investigate uptake in vegetative cells as well as differentiated heterocysts. We demonstrate a strong dependence of long-term cell integrity, activity, and viability on SWCNT surface functionalization. We further show differential uptake of SWCNTs across a single filament, with positively charged functionalized SWCNTs preferentially localizing within the heterocysts of the filament. This cell dependency of the nanoparticle internalization motivates the use of SWCNTs as a NIR stain for monitoring cell differentiation.

Asunto(s)

RESUMEN

The probability of occupational exposure rises with the increasing production and biomedical application of carbon nanotubes (CNTs). Thus, the risk of co-exposure of nanomaterials with environmental pollutants is also increasing. Although many studies have focused on the combined toxicity of nanomaterials and pollutants, more attention has been paid to the toxicity of nanomaterials after adsorbing pollutants or the toxicity of nanomaterials and pollutants exposed simultaneously. Few studies have been conducted on the toxicity and toxicity mechanisms of nanomaterials and environmental pollutants following sequential exposure. In this study, we employed THP-1 cells to investigate how pristine single walled CNTs (p-SWCNTs) and oxidized single walled CNTs (SWCNT-COOHs) pretreatments at a non-lethal dose of 10 µg/mL affect cell responses to metal ions (i. e., Pb2+, Cu2+, and Cr(VI)). We found that p-SWCNTs caused more significant damage to cell membrane integrity than SWCNT-COOHs, which led to higher metallothionein (MT) levels and increased transport of metal ions into cells. Pretreatment of p-SWCNTs in cells significantly increased the cytotoxicity of Pb2+, Cu2+, and Cr(VI) by 2-4-fold, whereas SWCNT-COOHs pretreated cells showed no noteworthy changes in response to heavy metals, which were further confirmed by the cellular reactive oxygen species (ROS) assays. These findings indicate that understanding the effects of the exposure sequence of engineered nanomaterials and environmental pollutants on their toxicity provides an excellent complement to combined toxicity evaluation.

Asunto(s)

RESUMEN

Using single-walled carbon nanotubes (SWCNTs) as an ion-to-electron transducer, a novel disposable all-solid-state desvenlafaxine-selective electrode based on a screen-printed carbon paste electrode was created. SWCNTs were put onto the carbon-paste electrode area, which was protected by a poly (vinyl chloride) (PVC) membrane with a desvenlafaxine-imprinted polymer serving as a recognition receptor. Electrochemical impedance spectroscopy and chronopotentiometric techniques were used to examine the electrochemical characteristics of the SWCNTs/PVC coating on the carbon screen-printed electrode. The electrode displayed a 57.2 ± 0.8 mV/decade near-Nernstian slope with a 2.0 × 10-6 M detection limit. In 10 mM phosphate buffer, pH 6, the ODV-selective electrodes displayed a quick reaction (5 s) and outstanding stability, repeatability, and reproducibility. The usefulness of electrodes was demonstrated in samples of ODV-containing pharmaceutical products and human urine. These electrodes have the potential to be mass produced and employed as disposable sensors for on-site testing, since they are quick, practical, and inexpensive.

RESUMEN

A foldable and cuttable sheet heater was fabricated using single-walled carbon nanotubes (SWCNTs) and aramid nanofibers (ANFs). SWCNTs are particularly well suited for Joule heating based on their high thermal stability, electrical properties, high current density, and aspect ratio. When the SWCNT/ANF composite reaches a high temperature during Joule heating, ANFs will endure this temperature due to their impressive thermal stability, derived from aramid fibers. With the aim of achieving a synergistic effect between the SWCNTs and ANFs, 0-100 wt% SWCNT/ANF composite sheets were fabricated by tip-type sonication and vacuum filtration. After assessing the thermal stability and electrical properties of the composite sheets, the Joule heating effect was analyzed. TGA showed that our sheet had high thermal stability in an air condition up to around 500 °C. The electrical conductivity of the composite sheet was improved as the amount of SWCNT added rose to 790.0 and 747.5 S/cm in the 75 and 100_SWCNTs/ANF, respectively. The maximum heating temperature, up to 280 °C, reached by Joule heating was measured as a function of SWCNT content and input voltage, and the relationship among SWCNT content, input voltage, heating temperature, and electric power was described. Mechanical properties were also measured in a temperature range similar to the heating temperature of 300 °C reached by Joule heating. Ultimately, we obtained a foldable and cuttable composite sheet with a stretchable structure, capable of being molded into a variety of shapes. This energy-efficient material can potentially be employed in any device in which a heater is required to deliver high temperatures.

RESUMEN

We recently assisted in a revolution in the realm of fluorescence microscopy triggered by the advent of super-resolution techniques that surpass the classic diffraction limit barrier. By providing optical images with nanometer resolution in the far field, super-resolution microscopy (SRM) is currently accelerating our understanding of the molecular organization of bio-specimens, bridging the gap between cellular observations and molecular structural knowledge, which was previously only accessible using electron microscopy. SRM mainly finds its roots in progress made in the control and manipulation of the optical properties of (single) fluorescent molecules. The flourishing development of novel fluorescent nanostructures has recently opened the possibility of associating super-resolution imaging strategies with nanomaterials' design and applications. In this review article, we discuss some of the recent developments in the field of super-resolution imaging explicitly based on the use of nanomaterials. As an archetypal class of fluorescent nanomaterial, we mainly focus on single-walled carbon nanotubes (SWCNTs), which are photoluminescent emitters at near-infrared (NIR) wavelengths bearing great interest for biological imaging and for information optical transmission. Whether for fundamental applications in nanomaterial science or in biology, we show how super-resolution techniques can be applied to create nanoscale images "in", "of" and "with" SWCNTs.

RESUMEN

We designed and tested a manufacturing process that resulted in the formation of composites with maximized electrical conductivity and optimized electromagnetic interference (EMI) shielding effectiveness (SE) properties. Single-walled carbon nanotube (SWCNT) paper, which is a microscopic aggregate of van der Waals force interaction, was impregnated with semi-cured epoxy to make SWCNT prepregs. These prepregs were completely cured into SWCNT/epoxy composites. Fabricating and curing processes were executed under proper temperature cycle depending on the time. We inspected SWCNT paper and the interfacial state between the SWCNTs and epoxy in the composite with a field emission-scanning electron microscopy and calculated the SWCNT weight fraction through thermogravimetric analysis measurements. Using these observations, electrical conductivity and EMI SE were investigated according to thickness which could be controlled by the suggested manufacturing process as 1-, 5- and 10-layer composites. Finally, we determined ideal composite thickness and the associated number of prepreg layers using skin depth theory.

RESUMEN

Flexible strain sensors are receiving a great deal of interest owing to their prospective applications in monitoring various human activities. Among various efforts to enhance the sensitivity of strain sensors, pre-crack generation has been well explored for elastic polymers but rarely on textile substrates. Herein, a highly sensitive textile-based strain sensor was fabricated via a dip-coat-stretch approach: a polyester woven elastic band was dipped into ink containing single-walled carbon nanotubes coated with silver paste and pre-stretched to generate prebuilt cracks on the surface. Our sensor demonstrated outstanding sensitivity (a gauge factor of up to 3550 within a strain range of 1.5-5%), high stability and durability, and low hysteresis. The high performance of this sensor is attributable to the excellent elasticity and woven structure of the fabric substrate, effectively generating and propagating the prebuilt cracks. The strain sensor integrated into firefighting gloves detected detailed finger angles and cyclic finger motions, demonstrating its capability for subtle human motion monitoring. It is also noteworthy that this novel strategy is a very quick, straightforward, and scalable method of fabricating strain sensors, which is extremely beneficial for practical applications.

Asunto(s)

RESUMEN

Development of large-area, low-cost, low-voltage, low-power consumption, flexible high-performance printed carbon nanotube thin-film transistors (TFTs) is helpful to promote their future applications in sensors and biosensors, wearable electronics, and the Internet of things. In this work, low-voltage, flexible printed carbon nanotube TFTs with a large-area and low-cost fabrication process were successfully constructed using ultrathin (∼3.6 nm) AlOx thin films formed by plasma oxidation of aluminum as dielectrics and screen-printed silver electrodes as contact electrodes. The as-prepared bottom-gate/bottom-contact carbon nanotube TFTs exhibit a low leakage current (∼10-10 A), a high charge carrier mobility (up to 9.9 cm2 V-1 s-1), high on/off ratios (higher than 105), and small subthreshold swings (80-120 mV/dec) at low operation voltages (from -1.5 to 1 V). At the same time, printed carbon nanotube TFTs showed a high response (ΔR/R = 99.6%) to NO2 gas even at 16 ppm with a faster response and recovery speed (∼8 s, exposure to 0.5 ppm NO2), a lower detection limit (0.069 ppm NO2), and a low power consumption (0.86 µW, exposure to 16 ppm NO2) at a gate voltage of 0.2 V at room temperature. Moreover, the printed carbon nanotube devices exhibited excellent mechanical flexibility and bias stress stability after 12,000 bending cycles at a radius of 5 mm and a bias stress test for 7200 s at a gate voltage of ±1 V, which originated from the ultrathin and compact AlOx dielectric and the super adhesion force between screen-printed silver electrodes and polyethylene terephthalate substrates.

RESUMEN

Potentiometric sensors have a great influence on the determination of most various compounds in their matrices. Therefore, efficient and new sensors were introduced to measure sodium Deoxycholate (NaDC) as a bile acid salt. These sensors are based on NaDC imprinted polymer (MIP) as sensory element. The MIP beads were synthesized using thermal polymerization pathway, in which acrylamide (AAm), ethylene glycol dimethacrylate (EGDMA), NaDC, and benzoyl peroxide (BPO) were used as the functional monomer, cross-linker, template, and initiator, respectively. The proposed sensors were fabricated using a coated screen-printed platform and the sensing membrane was modified by single-walled carbon nanotubes (SWCNTs) as an ion-to-electron transducer. The sensors exhibited high sensitivity that reached 4.7 × 10-5 M of near-Nernestian slope (-60.1 ± 0.9 mV/decade, r2 = 0.999 (n= 5)). In addition, the sensors revealed high selectivity, long lifetime, high potential stability, and conductivity that ensure reproducible and accurate results over a long time. MIP characterization was performed using Fourier Transform-Infrared (FT-IR) and a scanning electron microscope (SEM). Regarding the interaction of NaDC with serum albumin (SA), albumin is determined in human serum samples as human serum albumin (HSA), which was collected from different volunteers of different ages and gender.

Asunto(s)

RESUMEN

Single-walled carbon nanotubes (SWCNTs) are a group of widely used carbon-based nanomaterials (CNMs) with various applications, which raise increasing public concerns associated with their potential toxicological effect and risks on human and ecosystems. In this report, we comprehensively evaluated the nanotoxicity of SWCNTs with their relationship to varying lengths, functional groups and electronic structures, by employing both newly established quantitative toxicogenomics test, as well as conventional phenotypic bioassays. The objective is to reveal potential cellular toxicity and mechanisms of SWCNTs at the molecular level, and to probe their potential relationships with their morphological, surface, and electronic properties. The results indicated that DNA damage and oxidative stress were the dominant mechanisms of action for all SWCNTs and, the toxicity level and characteristics varied with length, surface functionalization and electronic structure. Distinguishable molecular toxicity fingerprints were revealed for the two SWCNTs with varying length, with short SWCNT exhibiting higher toxicity level than the long one. In terms of surface properties, SWCNT functionalization, namely carboxylation and hydroxylation, led to elevated overall toxicity, especially genotoxicity, as compared to unmodified SWCNT. Carboxylated SWCNT induced a greater toxicity than the hydroxylated SWCNT. The nucleus is likely the primary target site for long, short, and carboxylated SWCNTs and mechanical perturbation is likely responsible for the DNA damage, specifically related to degradation of the DNA double helix structure. Finally, dramatically different electronic structure-dependent toxicity was observed with metallic SWCNT exerting much higher toxicity than the semiconducting one that exhibited minimal toxicity among all SWCNTs.

RESUMEN

Optical sensors based on single-walled carbon nanotubes (SWCNTs) demonstrate tradeoffs that limit their use in in vivo and in vitro environments. Sensor characteristics are primarily governed by the non-covalent wrapping used to suspend the hydrophobic SWCNTs in aqueous solutions, and we herein review the advantages and disadvantages of several of these different wrappings. Sensors based on surfactant wrappings can show enhanced quantum efficiency, high stability, scalability, and diminished selectivity. Conversely, sensors based on synthetic and bio-polymer wrappings tend to show lower quantum efficiency, stability, and scalability, while demonstrating improved selectivity. Major efforts have focused on optimizing sensors based on DNA wrappings, which have intermediate properties that can be improved through synthetic modifications. Although SWCNT sensors have, to date, been mainly engineered using empirical approaches, herein we highlight alternative techniques based on iterative screening that offer a more guided approach to tuning sensor properties. These more rational techniques can yield new combinations that incorporate the advantages of the diverse nanotube wrappings available to create high performance optical sensors.

RESUMEN

Herein, a facile route leading to good single-walled carbon nanotubes (SWCNT) dispersion or poly (3,4-ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT/PSS) based single-piece nanocomposite membrane is proposed for trace determination of Cu2+ ions. The single-piece solid contact Cu2+-selective electrodes were prepared after drop casting the membrane mixture on the glassy-carbon substrates. The prepared potentiometric sensors revealed a Nernstian response slope of 27.8 ± 0.3 and 28.1 ± 0.4 mV/decade over the linearity range 1.0 × 10-3 to 2.0 × 10-9 and 1.0 × 10-3 to 1.0 × 10-9 M with detection limits of 5.4 × 10-10 and 5.0 × 10-10 M for sensors based on SWCNTs and PEDOT/PSS, respectively. Excellent long-term potential stability and high hydrophobicity of the nanocomposite membrane are recorded for the prepared sensors due to the inherent high capacitance of SWCNT used as a solid contact material. The sensors exhibited high selectivity for Cu2+ ions at pH 4.5 over other common ions. The sensors were applied for Cu2+ assessment in tap water and different tea samples. The proposed sensors were robust, reliable and considered as appealing sensors for copper (II) detection in different complex matrices.

Asunto(s)

RESUMEN

Wearable fiber-shaped electronic devices have drawn abundant attention in scientific research fields, and tremendous efforts are dedicated to the development of various fiber-shaped devices that possess sufficient flexibility. However, most studies suffer from persistent limitations in fabrication cost, efficiency, the preparation procedure, and scalability that impede their practical application in flexible and wearable fields. In this study, a simple, low-cost 3D printing method capable of high manufacturing efficiency, scalability, and complexity capability to fabricate a fiber-shaped integrated device that combines printed fiber-shaped temperature sensors (FTSs) with printed fiber-shaped asymmetric supercapacitors (FASCs) is developed. The FASCs device can provide stable output power to FTSs. Moreover, the temperature responsivity of the integrated device is 1.95% °C-1.

RESUMEN

A fiber-based single-walled carbon nanotube (SWCNT) thin-film-transistor (TFT) has been proposed. We designed complementary SWCNT TFT circuit based on SPICE simulations, with device parameters extracted from the fabricated fiber-based SWCNT TFTs, such as threshold voltage, contact resistance, and off-/gate-leakage current. We fabricated the SWCNTs CMOS inverter circuits using the selective passivation and n-doping processes on a fiber substrate. By comparing the simulation and experimental results, we could enhance the circuit's performance by tuning the threshold voltage between p-type and n-type TFTs, reducing the source/drain contact resistance and off current level, and maintaining a low output capacitance of the TFTs. Importantly, it was found that the voltage gain, output swing range, and frequency response of the fiber-based inverter circuits can be dramatically improved.

RESUMEN

The manufacturers of single-walled carbon nanotubes (SWCNTs) are continuously expanding their manufacturing and commercial markets, indicating that the environmental release and accumulation of SWCNTs in soil is inevitable. However, little is known about the effects of SWCNTs on soil physicochemical properties and soil microbial communities. Our results showed that treatment with SWCNTs resulted in an enhancement of microorganism metabolism related to soil organic compound degradation and a change in the structure of soil microbial communities, but the diversity of soil microorganisms was not significantly affected. The decrease in soil urease activity and the increase in the relative abundance of Nitrospirae after SWCNTs exposure might be relevant to the induction of soil nitrification. The relative abundances of phosphate-solubilizing microorganisms increased after exposure to SWCNTs, which was beneficial for phosphorus bioavailability in the soil. Our current study highlights that exposure to SWCNTs at concentrations of 3 and 10 µg/g can change the composition of soil microorganism communities, promote soil organic degradation and improve soil fertility by enhancing N and P availability in a short time.

Asunto(s)

RESUMEN

The synthesis, characterization, and the influence of single-walled carbon nanotubes (SWCNTs) modified with an anticancer drug doxorubicin (DOx) on the properties of model biological membrane as well as the comparison of the two modes of modification has been presented. The drug was covalently attached to the nanotubes either preferentially on the sides or at the ends of the nanotubes by the formation of hydrazone bond. The efficiency of the modification was proved by the results of FTIR, Raman, and thermogravimetric analysis. In order to characterize the influence of SWCNT-DOx conjugates on model biological membranes, Langmuir technique has been employed. The mixed monolayers composed of 1,2-dipalmitoyl-sn-glycero-3-phosphothioethanol (DPPTE) and SWCNT-DOx with different weight ratio have been prepared. It has been shown that changes in the isotherm characteristics depend on the SWCNTs content. While smaller amounts of SWCNTs do not exert significant differences, the introduction of the prevailing content of the nanotubes increases area per molecule and decreases the maximum value of compression modulus, leading to more fluid monolayer. However, upon increasing the surface pressure, the aggregation of carbon nanotubes within the thiolipid matrix has been observed. Mixed layers of DPPTE/SWCNT-DOx were also transferred onto gold electrodes by means of LB method. Cyclic voltammetry showed that SWCNT-DOx conjugates remain adsorbed at the electrode surface and are stable in time. Additionally, higher values of peak current and DOx surface concentration obtained for side modification prove that side modification allows for more efficient conjugation of the drug to carbon nanotubes. Graphical abstractᅟ.

RESUMEN

Carbon nanotubes (CNTs) exhibit a number of physicochemical properties that contribute to adverse biological outcomes. However, it is difficult to define the independent contribution of individual properties without purified materials. A library of highly purified single-walled carbon nanotubes (SWCNTs) of different lengths is prepared from the same base material by density gradient ultracentrifugation, designated as short (318 nm), medium (789 nm), and long (1215 nm) SWCNTs. In vitro screening shows length-dependent interleukin-1ß (IL-1ß) production, in order of long > medium > short. However, there are no differences in transforming growth factor-ß1 production in BEAS-2B cells. Oropharyngeal aspiration shows that all the SWCNTs induce profibrogenic effects in mouse lung at 21 d postexposure, but there are no differences between tube lengths. In contrast, these SWCNTs demonstrate length-dependent antibacterial effects on Escherichia coli, with the long SWCNT exerting stronger effects than the medium or short tubes. These effects are reduced by Pluronic F108 coating or supplementing with glucose. The data show length-dependent effects on proinflammatory response in macrophage cell line and antibacterial effects, but not on collagen deposition in the lung. These data demonstrate that over the length scale tested, the biological response to highly purified SWCNTs is dependent on the complexity of the nano/bio interface.

Asunto(s)

RESUMEN

Due to the excessive use of antibiotics over the years, the microorganisms have developed resistance to numerous drugs. The growth of multi-resistant organisms (MROs) heads due to the insufficient treatment with the currently available medications which present a great threat to the biotic component of the environment as well as to the food technology sectors. The goal of this research was to develop a nano-composite made up of single-walled carbon nanotubes (SWCNTs) and amine-functionalized porphyrin, which could further be used for the anti-microbial studies in presence of visible light showing photodynamic effect to inactivate cells. Photodynamic antimicrobial chemotherapy is gaining significant interest due to its capabilities as an innovative form of antimicrobial treatment. The development of anti-microbial photodynamic therapy (a-PDT) is a non-antibiotic access to inactivate microorganisms. We examined the synthesis of amine-functionalized porphyrin and conjugated it to the oxidised single-walled carbon nanotubes (SWCNTs). By the use of appropriate amount of single-walled carbon nanotubes (SWCNTs), we have shown the interaction between the porphyrin conjugated nanotubes and the bacterial cells in presence of visible light led to the cell membrane damage, concluding that SWCNT-porphyrin conjugates can be used as an antibacterial agent. The characterization of the oxidised SWCNT and SWCNT-porphyrin conjugates was determined by field emission scanning electron microscopy (FE-SEM), which provides detailed information about the composition and the morphological analysis. The particle size measurements were carried out by transmission electron microscopy (TEM). On investigating under the florescence microscopy, red fluorescence was observed. Thus, these properties demand us to design this facile material comprised of SWCNT-aminoporphyrin conjugates that shows potent antibacterial activity.

Asunto(s)