RESUMEN
As a bridge between the coating and the substrate, the primer has a direct impact on the adhesion performance of silicone resin thermal protection coating. In this paper, the synergistic effects of an aminosilane coupling agent on the adhesion performance of silane primer were investigated. The results show that silane primer containing N-aminoethyl-3-aminopropylmethyl-dimethoxysilane (HD-103) formed a continuous and uniform film on the surface of the substrate. Two amino groups of HD-103 were conducive to moderate and uniform hydrolysis of the silane primer system, and the introduction of dimethoxy groups was more conducive to the improvement of interfacial layer density and the formation of the planar surface structure, thus enhancing the bond strength at the interface. When the content was 13 wt%, it exhibited excellent synergistic effects on adhesive properties, and the adhesive strength reached 1.53 MPa. The possible morphology and composition of the silane primer layer were investigated by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). A thermogravimetric infrared spectrometer (TGA-IR) was used to analyze the thermal decomposition of the silane primer layer. The results showed that the alkoxy groups in the silane primer were first hydrolyzed to form Si-OH, and then the dehydration and condensation reactions between Si-OH and the substrate formed a firm network structure.
RESUMEN
Resin-ceramic hybrid materials for computer-aided design/computer-aided manufacturing (CAD/CAM resins) have been developed. In this study, the effects of the amount of light energy transmitted through the four types of 1.5-mm-thick CAD/CAM resin blocks on the bond performance of corresponding resin cement adhesive systems consisting of an adhesive and a dual-curable resin cement were examined. The bond strengths of the four types of resin cement adhesive systems decreased with decreasing the amount of light energy transmitted through CAD/CAM resin block, due to a decrease in the light-curable ability of dual-curable resin cements. However, the degradation behavior of the bond strengths was strongly affected by the types of adhesives and initiator systems utilized. The adhesive consisting of a dimethacrylate monomer and redox-initiators enhanced the bonding performance of the dual-curable resin cement more effectively than the adhesive, which consists of a dimethacrylate monomer and photo-initiators or a γ-me thacryloxypropyltrimethoxysilane and a 10-methacryloyloxydecyl dihydrogen phosphate.
Asunto(s)
Recubrimiento Dental Adhesivo , Cementos de Resina , Cerámica , Resinas Compuestas , Diseño Asistido por Computadora , Ensayo de Materiales , Propiedades de SuperficieRESUMEN
The aim of the study was to evaluate the stability, reactivity, and bond strength with a lithium disilicate ceramic of a self-etch silane primer (Monobond Etch and Prime/MEP). The stability was evaluated by 1H-,31P-NMR spectroscopy (before/after aging), and the reactivity by micro MIR-FTIR spectroscopy on Ge surfaces (0, 1, 24 h) using a prehydrolyzed silane primer (Calibra Silane Coupling Agent/CLB), as a control. The effect of MEP vs. 5% HF-etching on ceramic roughness was assessed by optical profilometry. The shear bond strength (SBS) of a resin composite bonded to polished ceramic surfaces treated with MEP, HF without silane (HF+NS), HF+CLB, and HF+MEP (n = 20) was evaluated after storage in water (A: 37 °C/1 week, B: 5000×/5-55 °C and C: 100 °C/24 h). Aging did not affect the silanol groups of MEP, but only the phosphate co-monomer. Silanols were reactive forming siloxanes, but exhibited lower consumption rate than CLB. HF-etching induced significantly higher values than MEP, in all the roughness parameters tested (Sa, Sz, Sdr, Sc, Sv), with the greatest differences found in Sdr and Sv. For SBS, MEP was inferior to all treatments/storage conditions, except of HF+NS in A, where the values were similar. However, on a HF-etched substrate, MEP provided highest strength and reliability.
RESUMEN
PURPOSE: To assess the effect of different surface pretreatments on the shear bond strength of resin luting material on CAD-CAM composite resins and a polymer-infiltrated ceramic network (PICN). MATERIALS AND METHODS: CAD-CAM materials (Brilliant Crios, Cerasmart, Lava Ultimate, VITA Enamic) were subjected to the following pretreatments: no pretreatment; grit blasting; grit blasting + silane; HF etching + silane; tribochemical silica coating + silane; manufacturers' specifications; manufacturers' specifications + silane; manufacturers' specifications using only the manufacturers' products including their recommended luting materials (DuoCem, G-Cem LinkForce, RelyX Ultimate, RelyX Unicem 2). Specimens were luted with resin luting material according to the Swiss shear test design. After six months of water storage, shear bond tests were performed. Data were analyzed with multiple linear regression models and nested models (α = 0.05). RESULTS: Low bond strengths were obtained without pretreatment (Brilliant Crios 3.01 ± 0.54 MPa, Cerasmart 2.66 ± 0.47 MPa, Lava Ultimate 1.76 ± 0.26 MPa, VITA Enamic 2.83 ± 0.63 MPa). Grit blasting achieved high bond strengths across all materials (Brilliant Crios 5.17 ± 0.77 MPa, Cerasmart 4.27 ± 0.50 MPa, Lava Ultimate 3.98 ± 0.54 MPa, VITA Enamic 4.97 ± 0.90 MPa). Silane application tended to decrease bond strengths on CAD-CAM composite resins. Following the manufacturers' specifications and using their recommended materials achieved the highest bond strengths for all materials except Cerasmart (Brilliant Crios 5.75 ± 0.91 MPa, Cerasmart 2.82 ± 0.28 MPa, Lava Ultimate 6.63 ± 0.97 MPa, VITA Enamic 7.09 ± 0.77 MPa). CONCLUSION: Grit blasting and the application of a suitable material primer is a useful pretreatment for the bonding of CAD-CAM composite resins. Silane application on CAD-CAM composite resins may entail drawbacks, possibly owing to the scarcity of silanizable fillers.
Asunto(s)
Recubrimiento Dental Adhesivo , Cerámica , Diseño Asistido por Computadora , Ensayo de Materiales , Polímeros , Propiedades de SuperficieRESUMEN
As the proportion of adult orthodontic treatment increases, mainly for aesthetic reasons, orthodontic brackets are directly attached to yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) restorations. This, study analyzed the shear bond strength (SBS) between various surface treated Y-TZP and orthodontic metal brackets. The Y-TZP specimens were conditioned by 110 µm Al2O3 sandblasting, or sandblasting followed by coating with one of the primers (silane, MDP, or an MDP-containing silane primer). After surface treatment, the orthodontic metal bracket was bonded to the specimen using a resin cement, and then 24 h storage in water and thermal cycling (5000 cycles, 5-55 °C), SBS was measured. Surface roughness was analyzed for surface morphology, and X-ray photoelectron spectroscopy (XPS) was employed for characterization of the chemical bond between the Y-TZP and the MDP-based primers (MDP, MDP containing silane primer). It was found that after surface treatment, the surface roughness of all groups increased. The groups treated with 110 µm Al2O3 sandblasting and MDP, or MDP-containing silane primer showed the highest SBS values, at 11.92 ± 1.51 MPa and 13.36 ± 2.31 MPa, respectively. The SBS values significantly decreased in all the groups after thermal cycling. Results from XPS analysis demonstrated the presence of chemical bonds between Y-TZP and MDP. Thus, the application of MDP-based primers after Al2O3 sandblasting enhances the resin bond strength between Y-TZP and the orthodontic metal bracket. However, bonding durability of all the surface-treated groups decreased after thermal cycling.
RESUMEN
This study examined the effects of 3 mol % yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) ceramic surface treatments on the tensile bond strength and surface characteristics of enamel. To measure the tensile bond strength, the 3Y-TZP and tooth specimens were manufactured in a mini-dumbbell shape and divided into four groups based on the type of 3Y-TZP surface treatment: polishing (P), 110 µm alumina sandblasting (S), 110 µm alumina sandblasting combined with selective infiltration etching (SS), and 110 µm alumina sandblasting combined with MDP (10-methacryloyloxydecyl dihydrogen phosphate)-containing silane primer (SP). After surface treatment, the surface roughness, wettability, and surface changes were examined, and the tensile bond strength was measured. The mean values (from lowest to highest) for tensile bond strength (MPa) were as follows: P, 8.94 ± 2.30; S, 21.33 ± 2.00; SS, 26.67 ± 4.76; and SP, 31.74 ± 2.66. Compared to the P group, the mean surface roughness was significantly increased, and the mean contact angle was significantly decreased, while wettability was increased in the other groups. Therefore, surface treatment with 110 µm alumina sandblasting and MDP-containing silane primer is suitable for clinical applications, as it considerably improves the bond strength between 3Y-TZP and enamel.
RESUMEN
AIM: To assess the microtensile bond strength of repaired composite resin that was surface treated by diamond point or silicon carbide followed by bonding using either only total- etch bonding regimen or silane coupling agent with adhesive resin. MATERIALS AND METHODS: Fourteen composite blocks were aged under deionized water for 14 days. The bonding surface was prepared with coarse diamond point or silicon carbide. Two blocks with no surface treatment were used as control groups. The bonding regimen was either total-etch bonding regimen or silane coupling agent and bonding agent. The aged samples were then bonded to new composite. Five sections per block (each 1mm thick) were prepared; cut to obtain an adhesive zone of approximately 1mm(2) and subjected to microtensile bond strength testing. RESULTS: The highest bond strength was obtained by surface treatment by coarse diamond point and total etch bonding regimen and least by silicon carbide and silane. A statistically significant difference was seen in all the four groups. CONCLUSIONS: Surface treatment by a coarse diamond point and total-etch bonding regimen provides highest bond strength. Thus, a simpler treatment regimen can contribute to a better bond strength in repaired composites.