RESUMEN

The present study describes a novel double-modified strategy for developing high-performance thin-film composite reverse osmosis (TFC-RO) membranes by incorporating titanium-based metal organic frameworks (NH2-MIL-125) and functionalised multiwalled carbon nanotubes (MWCNTs) into the support layer and selective layer, respectively. Initially, the support layer was subjected to successive modifications using NH2-MIL-125 mixed with polysulfone (PSF) in dimethylformamide DMF solution to investigate their impact on the performance and properties of the support layer and resultant TFC-RO membranes. Results indicated that the new structure of the modified support layer had significant influences on the developed TFC-RO membranes. Notably, the pristine PSF support exhibited a large surface pore size, medium porosity, and strong hydrophobicity, resulting in a low-flux TFC-RO membrane. However, after modification with NH2-MIL-125, the optimal blend support demonstrated a small surface pore size, high porosity, and improved hydrophilicity, favouring the formation of a high performance TFC-RO membrane. The incorporation of functionalised MWCNTs nanochannels into the selective layer, using the optimal NH2-MIL-125-PSF blended support, resulted in a smoother and more hydrophilic TFC-RO membrane with enhanced negative charge to improve antifouling properties against negative foulants (i.e., nanoplastics (NPs) and bovine serum albumin (BSA)). The double-modified membrane (TFC-RO-DM) exhibited superior performance over the conventional PSF-TFC-RO membrane. Notably, the maximum water flux reached 39 L m-2.h-1 with 98.4% NaCl rejection. The membrane exhibited a high flux recovery rate of 92% following a 30-min physical cleaning process. Additionally, the TFC-RO-DM membrane displayed reduced fouling against NPs suggesting the great promise of this innovative double-modification approach for the advancement of high-performance TFC-RO membranes.

Asunto(s)

RESUMEN

Biofouling refers to the undesirable growth of microorganisms on water-submerged surfaces. Microfouling, the initial state of biofouling, is characterized by aggregates of microbial cells enclosed in a matrix of extracellular polymeric substances (EPSs). In seawater desalination plants, filtration systems, such as reverse-osmosis membranes (ROMs), are affected by microfouling, which decreases their efficiency in obtaining permeate water. The existing chemical and physical treatments are expensive and ineffective; therefore, controlling microfouling on ROMs is a considerable challenge. Thus, new approaches are necessary to improve the current ROM cleaning treatments. This study demonstrates the application of Alteromonas sp. Ni1-LEM supernatant as a cleaning agent for ROMs in a desalination seawater plant in northern Chile (Aguas Antofagasta S.A.), which is responsible for supplying drinking water to the city of Antofagasta. ROMs treated with Altermonas sp. Ni1-LEM supernatant exhibited statistically significant results (p < 0.05) in terms of seawater permeability (Pi), permeability recovery (PR), and the conductivity of permeated water compared with control biofouling ROMs and those treated with the chemical cleaning protocol applied by the Aguas Antofagasta S.A. desalination plant.

RESUMEN

This study revealed the effects of incorporating ionic liquid (IL) molecules: 1-ethyl, 1-butyl, and 1-octyl-3-methyl-imidazolium chlorides with different alkyl chain lengths, in interfacial polymerization (IP) on the structure and property (i.e., permeate-flux and salt rejection ratio) relationships of resulting RO membranes. The IL additive was added in the aqueous meta-phenylene diamine (MPD; 0.1% w/v) phase, which was subsequently reacted with trimesoyl chloride (TMC; 0.004% w/v) in the hexane phase to produce polyamide (PA) barrier layer. The structure of resulting free-standing PA thin films was characterized by grazing incidence wide-angle X-rays scattering (GIWAXS), which results were correlated with the performance of thin-film composite RO membranes having PA barrier layers prepared under the same IP conditions. Additionally, the membrane surface properties were characterized by zeta potential and water contact angle measurements. It was found that the membrane prepared by the longer chain IL molecule generally showed lower salt rejection ratio and higher permeation flux, possibly due to the inclusion of IL molecules in the PA scaffold. This hypothesis was supported by the GIWAXS results, where a self-assembled surfactant-like structure formed by IL with the longest aliphatic chain length was detected.

RESUMEN

The decline in the performance of spiral-wound reverse osmosis (SWRO) membranes is frequently due to biofouling. This study focus on qualitative and quantitative diagnosis of SWRO membrane biofouling. Bacterial counts on the different surfaces of the fouled membranes were carried out. Surface enhanced Raman spectroscopy (SERS) was performed to highlight clogging materials as well as their natures and identity. The topography of the fouled membranes and the structures of biofilms were visualized by fluorescence microscopy (FM) and scanning electron microscopy (SEM). The results indicated the presence of bacteria in the different SWRO membrane areas. Those strongly adhered were significantly higher than those weakly. It varied between 26 × 105 and 262 × 105 CFU m-2. However, SERS mapping showed different fouling levels and the thickness of the fouling layer was 5 µm. Microscopic imaging revealed biotic and abiotic deposits. These data can together allow better management of the seawater desalination process.

Asunto(s)

RESUMEN

Reverse osmosis (RO) desalination is a technology that is commonly used to mitigate water scarcity problems; one of its disadvantages is the bio-fouling of the membranes used, which reduces its performance. In order to minimize this problem, this study prepared modified thin film composite (TFC) membranes by the incorporation of chitosan-silver particles (CS-Ag) of different molecular weights, and evaluated them in terms of their anti-biofouling and desalination performances. The CS-Ag were obtained using ionotropic gelation, and were characterized by Fourier transform infrared spectroscopy (FTIR), high-resolution scanning electron microscopy (HR-SEM), energy-dispersive X-ray spectroscopy (EDX), thermogravimetric analysis (TGA) and dynamic light scattering (DLS). The modified membranes were synthetized by the incorporation of the CS-Ag using the interfacial polymerization method. The membranes (MCS-Ag) were characterized by Fourier transform infrared spectroscopy (FTIR), atomic force microscopy (AFM) and contact angle. Bactericidal tests by total cell count were performed using Bacillus halotolerans MCC1, and anti-adhesion properties were confirmed through biofilm cake layer thickness and total organic carbon (%). The desalination performance was defined by permeate flux, hydraulic resistance, salt rejection and salt permeance by using 2000 and 5000 mg L-1 of NaCl. The MCS-Ag-L presented superior permeate flux and salt rejection (63.3% and 1% higher, respectively), as well as higher bactericidal properties (76% less in total cell count) and anti-adhesion capacity (biofilm thickness layer 60% and total organic carbon 75% less, compared with the unmodified membrane). The highest hydraulic resistance value was for MCS-Ag-M. In conclusion, the molecular weight of CS-Ag significantly influences the desalination and the antimicrobial performances of the membranes; as the molecular weight decreases, the membranes' performances increase. This study shows a possible alternative for increasing membrane useful life in the desalination process.

RESUMEN

The direct end-of-life recycling of reverse osmosis membranes (RO) into recycled nanofiltration (r-NF) membranes has been pointed out as a circular technology. For the first time, an environmental analysis of the whole life cycle of r-NF membranes was performed, focused on their usage. The carbon footprint (CF) of NF water treatment processes (Functional Unit: 1 m3 of treated water) with different pressure vessel (PV) designs and energy sources using r-NF and commercial NF-270-400 was quantified. Moreover, to compensate for the lower permeability of the r-NF, two design strategies were assessed: A) an increment in inlet pressure, and B) an increase in the number of modules. The inventory included energy modelling for each design and membrane. The interaction of both strategies with the permeability and service life of r-NF, together with different energy sources, was assessed using a novel hybrid analytical-numerical method. The relevance of energy use at the usage stage was highlighted. Therefore, r-NF permeability is the foremost relevant parameter for the definition of CF. The low impact of the r-NF replacement favoured strategy B. The use of an environmental indicator (CF) made it possible to identify the frontiers of the recyclability and applicability of r-NF membranes.

RESUMEN

Organic matter (OM) in surface and ground waters may cause membrane fouling that is laborious to clean once established. Spontaneous osmotic backwash (OB) induced by solar irradiance fluctuation has been demonstrated for early mineral scaling/organic fouling control in decentralised small-scale photovoltaic powered-nanofiltration/reverse osmosis (PV-NF/RO) membrane systems. However, various OM types will interact differently with membranes which in turn affects the effectiveness of OB. This work evaluates the suitability of spontaneous OB cleaning for eleven OM types (covering low-molecular-weight organics (LMWO), humic substances, polyphenolic compounds and biopolymers) regarding adhesive interactions with NF/RO membranes. The adhesive interactions were quantified by an asymmetric flow field-flow fractionation coupled with an organic carbon detector (FFFF-OCD). The underlying mechanism of OM-membrane adhesive interactions affecting OB cleaning was elucidated. The results indicate that humic acid (a typical humic substance) and tannic acid (a typical polyphenolic compound) induced stronger adhesive interaction with NF/RO membranes than biopolymers and LMWO. When the mass loss of an OM due to adhesion was below a critical range, the spontaneous OB is most effective (>85% flux recovery); and above this range, the OB becomes ineffective (<50% flux recovery). Polyphenolic compounds and humic substances resulted in lower OB cleaning efficiency, due to their higher aromatic content, enhancing hydrophobic interactions and hydrogen bonding. Calcium-facilitated adhesion of some OM types (such as humic substances, polyphenolics and biopolymers) increased irreversible organic fouling potential and weakened OB cleaning, which was verified by both FFFF-OCD and membrane filtration results. This work provides a guidance to formulate strategies to enhance spontaneous OB cleaning, such as first identifying the adhesion of OM in feedwater (surface and ground waters) using FFFF-OCD, and then removing "sticky" OM using suitable pre-treatment processes.

Asunto(s)

RESUMEN

The Middle East will face tremendous water scarcity by 2050, which can only be mitigated by large-scale reverse osmosis seawater desalination. However, the coastal land in the region is rare and costly, so outsourcing the desalination facility to artificial islands could become a realistic scenario. This study investigated the ecological and economic challenges and possible advantages of that water supply option by analysing conceptual alternatives for offshore membrane-based desalination plants of up to 600 MCM/y capacity. Key environmental impacts and mitigation strategies were identified, and a detailed economic analysis was conducted to compare the new approach to state-of-the-art. The economic analysis included calculating the cost of water production (WPC) and discussing the differences between offshore alternatives and a conventional onshore desalination plant. In addition, the study investigated the impact of a changing energy mix and potential carbon tax levels on the WPC until 2050. The results indicate that offshore desalination plants have ecological advantages compared to onshore desalination plants. Furthermore, the construction cost for the artificial islands has a much lower effect on the WPC than energy cost. In contrast, the impact of potential carbon tax levels on the WPC is significant. The specific construction cost ranges between 287 $/m2 and 1507 $/m2 depending on the artificial island type and distance to the shoreline, resulting in a WPC between 0.51 $/m3 and 0.59 $/m3. This work is the first to discuss the environmental and economic effects of locating large-scale seawater desalination plants on artificial islands.

RESUMEN

The purpose of our study was to reduce the carbon footprint of seawater desalination plants that use reverse osmosis membranes by introducing on-site renewable energy sources. By using new-generation membranes with a low energy consumption and considering wind and photovoltaic energy sources, it is possible to greatly reduce the carbon footprint of reverse osmosis plants. The objective of this study was to add a renewable energy supply to a desalination plant that uses reverse osmosis technology. During the development of this research study, photovoltaic energy was discarded as a possible source of renewable energy due to the wind conditions in the area in which the reverse osmosis plant was located; hence, the installation of a wind turbine was considered to be the best option. As it was a large-capacity reverse osmosis plant, we decided to divide the entire desalination process into several stages for explanation purposes. The desalination process of the facility consists of several phases: First, the seawater capture process was performed by the intake tower. This water was then transported and stored, before going through a physical and chemical pre-treatment process, whereby the highest possible percentage of impurities and organic material was eliminated in order to prevent the plugging of the reverse osmosis modules. After carrying out the appraisals and calculating the amount of energy that the plant consumed, we determined that 15% of the plant's energy supply should be renewable, corresponding to 1194 MWh/year. As there was already a wind power installation in the area, we decided to use one of the wind turbines that had already been installed-specifically, an Ecotecnia turbine (20-150) that produced an energy of 1920 MWh /year. This meant that only a single wind turbine was required for this project.

RESUMEN

Reverse osmosis (RO) is the most widely used technology for seawater desalination purposes. The long-term operating data of full-scale plants is key to analyse their performance under real conditions. The studied seawater reverse osmosis (SWRO) desalination plant had a production capacity of 5000 m3/d for irrigation purposes. The operating data such as conductivities flows, and pressures were collected for around 27,000 h for 4 years. The plant had sand and cartridge filters without chemical dosing in the pre-treatment stage, a RO system with one stage, 56 pressure vessels, seven RO membrane elements per pressure vessel and a Pelton turbine as energy recovery device. The operating data allowed to calculate the average water and salt permeability coefficients (A and B) of the membrane as well as the specific energy consumption (SEC) along the operating period. The calculation of the average A in long-term operation allowed to fit the parameters of three different models used to predict the mentioned parameter. The results showed a 30% decrease of A, parameter B increase around 70%. The SEC was between 3.75 and 4.25 kWh/m3. The three models fitted quite well to the experimental data with standard deviations between 0.0011 and 0.0015.

RESUMEN

We present operando small-angle neutron scattering (SANS) experiments on silica fouling at two reverse osmose (RO) membranes under almost realistic conditions of practiced RO desalination technique. To its realization, two cells were designed for pressure fields and tangential feed cross-flows up to 50 bar and 36 L/h, one cell equipped with the membrane and the other one as an empty cell to measure the feed solution in parallel far from the membrane. We studied several aqueous silica dispersions combining the parameters of colloidal radius, volume fraction, and ionic strength. A relevant result is the observation of Bragg diffraction as part of the SANS scattering pattern, representing a crystalline cake layer of simple cubic lattice structure. Other relevant parameters are silica colloidal size and volume fraction far from and above the membrane, as well as the lattice parameter of the silica cake layer, its volume fraction, thickness, and porosity in comparison with the corresponding permeate flux. The experiments show that the formation of cake layer depends to a large extent on colloidal size, ionic strength and cross-flow. Cake layer formation proved to be a reversible process, which could be dissolved at larger cross-flow. Only in one case we observed an irreversible cake layer formation showing the characteristics of an unstable phase transition. We likewise observed enhanced silica concentration and/or cake formation above the membrane, giving indication of a first order liquid-solid phase transformation.

RESUMEN

Biofilm in reverse osmosis (RO) membranes is a common problem in water treatment at haemodialysis facilities. Bacteria adhere and proliferate on RO membranes, forming biofilms, obstructing and damaging the membranes and allowing the transfer of bacteria and/or cellular components potentially harmful to the health of haemodialysis patients. Our aim was to characterize the bacterial community associated to biofilm of RO membranes and to identify potentially pathogenic bacteria present in the haemodialysis systems of two dialysis centres in Chile. The diversity of the bacterial communities present on RO membranes and potable and osmosed water samples was evaluated using Illumina sequencing. Additionally, bacteria from potable water, osmosed water and RO membrane samples were isolated, characterized and identified by Sanger's sequencing. The molecular analyses of metagenomics showed that the phyla having a greater relative abundance in both dialysis centres were Proteobacteria and Planctomycetes. Pseudomonas, Stenotrophomonas, Agrobacterium, Pigmentiphaga, Ralstonia, Arthrobacter, Bacteroides and Staphylococcus were bacterial genera isolated from the different samples obtained at both haemodialysis centres. Pseudomonas spp. was a bacterial genus with greater frequency in all samples. Pseudomonas and Staphylococcus showed higher levels of resistance to the antibiotics tested. Results demonstrated the presence of potentially pathogenic bacteria, showing resistance to antimicrobials on RO membranes and in osmosed water in both dialysis centres studied.

RESUMEN

Reverse osmosis membranes are used within the oil and gas industry for seawater desalination on off-shore oilrigs. The membranes consist of three layers of material: a polyester backing layer, a polysulfone support and a polyamide (PA) thin film separating layer. It is generally thought that the PA layer controls ion selectivity within the membrane but little is understood about its structure or chemistry at the molecular scale. This active polyamide layer is synthesized by interfacial polymerization at an organic/aqueous interface between m-phenylenediamine and trimesoyl chloride, producing a highly cross-linked PA polymer. It has been speculated that the distribution of functional chemistry within this layer could play a role in solute filtration. The only technique potentially capable of probing the distribution of functional chemistry within the active PA layer with sufficient spatial and energy resolution is scanning transmission electron microscopy combined with electron energy-loss spectroscopy (STEM-EELS). Its use is a challenge because organic materials suffer beam-induced damage at relatively modest electron doses. Here we show that it is possible to use the N K-edge to map the active layer of a PA film using monochromated EELS spectrum imaging. The active PA layer is 12 nm thick, which supports previous neutron reflectivity data. Clear changes in the fine structure of the C K-edge across the PA films are measured and we use machine learning to assign fine structure at this edge. Using this method, we map highly heterogeneous intensity variations in functional chemistry attributed to N-C═C bonds within the PA. Similarities are found with previous molecular dynamics simulations of PA showing regions with a higher density of amide bonding as a result of the aggregation process at similar length scales. The chemical pathways that can be deduced may offer a clearer understanding of the transport mechanisms through the membrane.

RESUMEN

Polyamide (PA) semipermeable membranes typically used for reverse osmosis water treatment processes are prone to fouling, which reduces the amount and quality of water produced. By synergistically coupling the photothermal and bactericidal properties of graphene oxide (GO) nanosheets, gold nanostars (AuNS), and hydrophilic polyethylene glycol (PEG) on PA reverse osmosis membrane surfaces, we have dramatically improved fouling resistance of these membranes. Batch fouling experiments from three classes of fouling are presented: mineral scaling (CaCO3 and CaSO4), organic fouling (humic acid), and biofouling (Escherichia coli). Systematic analyses and a variety of complementary techniques were used to elucidate fouling resistance mechanisms from each layer of modification on the membrane surface. Both mineral scaling and organic fouling were significantly reduced in PA-GO-AuNS-PEG membranes compared to other membranes. The PA-GO-AuNS-PEG membrane was also effective in killing all near-surface bacteria compared to PA membranes. In the PA-GO-AuNS-PEG membrane, the GO nanosheets act as templates for in situ AuNS growth, which then facilitated localized heating upon irradiation by an 808 nm laser inactivating bacteria on the membrane surface. Furthermore, AuNS in the membrane assisted PEG in preventing mineral scaling on the membrane surface. In flow-through flux and foulant rejection tests, PA-GO-AuNS-PEG membranes performed better than PA membranes in the presence of CaSO4 and humic acid model foulants. Therefore, the newly suggested membrane surface modifications will not only reduce fouling from RO feeds, but can improve overall membrane performance. Our innovative membrane design reported in this study can significantly extend the lifetime and water treatment efficacy of reverse osmosis membranes to alleviate escalating global water shortage from rising energy demands.

Asunto(s)