RESUMEN

Glass ceramics are widely used to manufacture esthetic veneers, inlays, onlays, and crowns. Although the clinical survival rates ofglass-ceramic restorations arefavorable,fractures or chips are common. Certain cases can be repaired with direct composite. AIM: The aim of this study was to investigate the interaction effect of different designs and surface treatments on the load-to-failure of lithium disilicate glass-ceramic repaired with nanofilled composite. MATERIALS AND METHOD: Lithium-disilicate glass-ceramic slabs (IPS e.max Press, Ivoclar Vivadent) with three different designs of the top surface (flat, single plateau, or doubleplateau) (n=U) received 'no treatment', '5% HF etching', or "AI2O3 sandblasting". HF-etched and sandblasted slabs also received silane and universal one-step adhesive application. All slabs were incrementally repaired with nanofilled composite (Filtek Z350, 3M ESPE) up to6 mm above the highest ceramic top plateau. Specimens were stored in artificial saliva at 37 °C for 21 days and then subjected to 1,000 thermocycles between 5 and 55 °C. The interface composite-ceramic of each specimen was tensile tested until failure in a universal testing machine and the mode of failure was determined under a stereomicroscope. The ceramic surface morphology of one representative tested specimen from each subgroup (design/surface treatment) was observed through scanning electron microscopy (SEM). RESULTS: Regardless of ceramic design, the absence of surface treatment resulted in significantly lower load-to-failure values. No significant differences in load-to-failure values were observed between HF-etched and sandblasted specimens for the flat design; however, HF etching resulted in significantly higher load-to-failure values than sandblasting for both single plateau and double plateau designs. The majority (60%) of HF-etched specimens with single plateau or double plateau presented mixed failures. SEM photomicrographs showed that HF-etched specimens had smoother surfaces than sandblasted specimens. CONCLUSION: The surface treatment of a defective lithium disilicate glass-ceramic restoration has more influence than its macroscopic design on the retention of the composite repair. HF etching seems to provide higher bond strength to the composite repair.

Embora fraturas e lascamento de restauragoes vitrocerámicas sejam comuns, alguns casos podem ser reparados com compósito direto. OBJETIVO: investigar o efeito da interagao de diferentes formas e tratamentos de superficie na carga de ruptura de uma vitrocerámica reforgada com dissilicato de litio reparada com compósito nanoparticulado. MATERIAIS E MÉTODOS: A superficie superior de espécimes de vitroceramica (IPS e.max Press, Ivoclar Vivadent) foi preparada com tres formas (plana, plato único, ou duplo) e recebeu (n=11): 'nenhum tratamento', 'condicionamento com ácido hidrofluoridrico 5%', ou 'jateamento com AfOf. Ambos espécimes condicionados e jateados receberam silano e adesivo universal. Todos os espécimes foram reparados incrementalmente com compósito (Filtek Z350, 3M ESPE) até6 mm acima do plato cerámico mais alto, armazenados em saliva artificial á 37 °C por 21 dias, e submetidos á 1.000 termociclos (5 e 55 °C). A interface compósito-cerámica de cada amostra foi testada á tragao até sua falha em máquina universal e o modo de falha foi determinado com estereomicroscópio. A morfologia da superficie de uma amostra representativa de forma/tratamento de superficie foi observada através de microscopia eletronica de varredura (MEV). RESULTADOS: Independentemente da forma ceramica, a ausencia de tratamento superficial resultou em valores de carga de ruptura significativamente menores. Nao foi observada differenga significativa entre os espécimes planos condicionados ou jateados; no entanto, o condicionamento resultou em valores significativamente maiores que o jateamento para espécimes com plato único e duplo. A maioria (60%) dos espécimes condicionados e com plato único ou duplo apresentou falhas mistas. Imagens SEM demonstraram rugosidade superficial mais regular dos espécimes condicionados que os jateados. CONCLUSÕES: O tratamento superficial de uma restauragao defeituosa de vitrocerámica reforgada por dissilicato de litio tem maior influencia na retengao do reparo de compósito do que sua forma macroscópica; ainda, o condicionamento com ácido hidrofluoridrico parece proporcionar maior resistencia de uniao ao reparo com compósito.

Asunto(s)

RESUMEN

OBJECTIVE: The aim of the present study was to evaluate the influence of multidirectional brushing on the surface roughness, morphology, and bonding interface of resin-repaired CAD-CAM ceramic and composite restorations. MATERIALS AND METHODS: Twelve (N = 12) blocks (4 mm × 4 mm × 2 mm for parallel axis; 5 mm × 4 mm × 2 mm for perpendicular axis) of lithium disilicate glass-ceramic (IPS e.max CAD, Ivoclar AG) and CAD-CAM resin composite (Tetric CAD, Ivoclar AG) were obtained and repaired with direct resin composite (Clearfil AP-X, Kuraray). An abrasive slurry was prepared and the brushing was performed according to each restorative material and axis of brushing (n = 6; perpendicular to repair interface and parallel to repair interface) during 3,650 cycles (240 strokes per minute) to simulate 3 years of brushing. The surface roughness (Ra) and the profile variation for each material (restoration and direct repair resin composite) were measured at the baseline condition and after brushing, and the mean roughness and presence of steps at the repair interface were evaluated through factorial analysis of Variance (ANOVA). Scanning Electron Microscopy (SEM) images were taken to evaluate the surface topography of the repaired materials after brushing. RESULTS: The mean roughness of the repaired CAD-CAM restorations was affected by the brushing (P < .05), mainly when evaluating the repair material and the interface (P < .05), while the restorative CAD-CAM materials presented more stable values. The profile evaluation showed higher steps at the interface when repairing lithium disilicate than for CAD-CAM resin composite. CONCLUSION: Repaired CAD-CAM restorations were susceptible to wear after brushing simulation. The surface roughness of the direct resin composite was the most affected leading to step development at the interface, particularly in the repaired lithium disilicate samples. Cinical maintenance recalls and polishing protocols must be considered to enhance the longevity of such restorations.

Asunto(s)

RESUMEN

BACKGROUND: The need for dental rehabilitation under general anesthesia is increasing, with varying needs between patients. Mortality has been found to be a rare event in these patients; however other perioperative events can and do occur. Previous studies have established increased incidence of perioperative events with younger, sicker children, and longer anesthetics, however, no studies to date have evaluated if the incidence of perioperative events is more closely associated with one long anesthetic or multiple anesthetics per patient. AIMS: To evaluate the association of perioperative events related to single anesthetic duration or number of anesthetics per patient for dental rehabilitation. METHODS: After Children's Wisconsin Human Research Protection Program determined this quality activity did not meet the definition of human subjects research, we performed an epidemiologic observational evaluation by extracting all dental related cases (dental alone or with oral surgeon vs. dental with other specialties) with an associated general anesthesia encounter from Children's Wisconsin electronic data warehouse from June 1, 2015 to December 31, 2021. These cases occurred at a free-standing children's hospital or associated pediatric-only ambulatory surgery center. The risk of perioperative safety events was analyzed for previously identified risk groups such as American Society of Anesthesiologists Physical Status (ASA-PS), patient age, anesthesia case time with the addition of number of dental cases per patient. RESULTS: In this study, 8468 procedures were performed on 8082 patients. Of this cohort, 7765 patients underwent one procedure for dental care while 317 patients underwent a total of 703 dental-related procedures, ranging from two to five procedures per patient. Multivariable logistic regression identified increased risk of perioperative events in patients with ASA-PS 3 (n = 1459, rate 1.78%, p value .001, OR 5.7, CI 2.1-15.5) and ASA-PS 4 (n = 86, rate 5.8%, p < .001, OR 17.2, CI 4.4-67.3), anesthesia duration (p < .001, OR 1.46, CI 1.21-1.76), but no increased risk with number of anesthetics per patient (p value .54, OR 0.81, CI 0.4-1.61). CONCLUSIONS: Limiting dental care under general anesthesia to multiple short cases may decrease the risk of perioperative events when compared to completing all treatment in one long operative session.

Asunto(s)

RESUMEN

ABSTRACT Glass ceramics are widely used to manufacture esthetic veneers, inlays, onlays, and crowns. Although the clinical survival rates ofglass-ceramic restorations arefavorable,fractures or chips are common. Certain cases can be repaired with direct composite. Aim The aim of this study was to investigate the interaction effect of different designs and surface treatments on the load-to-failure of lithium disilicate glass-ceramic repaired with nanofilled composite. Materials and Method Lithium-disilicate glass-ceramic slabs (IPS e.max Press, Ivoclar Vivadent) with three different designs of the top surface (flat, single plateau, or doubleplateau) (n=U) received 'no treatment', '5% HF etching', or "AI2O3 sandblasting". HF-etched and sandblasted slabs also received silane and universal one-step adhesive application. All slabs were incrementally repaired with nanofilled composite (Filtek Z350, 3M ESPE) up to6 mm above the highest ceramic top plateau. Specimens were stored in artificial saliva at 37 °C for 21 days and then subjected to 1,000 thermocycles between 5 and 55 °C. The interface composite-ceramic of each specimen was tensile tested until failure in a universal testing machine and the mode of failure was determined under a stereomicroscope. The ceramic surface morphology of one representative tested specimen from each subgroup (design/surface treatment) was observed through scanning electron microscopy (SEM). Results Regardless of ceramic design, the absence of surface treatment resulted in significantly lower load-to-failure values. No significant differences in load-to-failure values were observed between HF-etched and sandblasted specimens for the flat design; however, HF etching resulted in significantly higher load-to-failure values than sandblasting for both single plateau and double plateau designs. The majority (60%) of HF-etched specimens with single plateau or double plateau presented mixed failures. SEM photomicrographs showed that HF-etched specimens had smoother surfaces than sandblasted specimens. Conclusion The surface treatment of a defective lithium disilicate glass-ceramic restoration has more influence than its macroscopic design on the retention of the composite repair. HF etching seems to provide higher bond strength to the composite repair.

RESUMO Embora fraturas e lascamento de restauragoes vitrocerámicas sejam comuns, alguns casos podem ser reparados com compósito direto. Objetivo investigar o efeito da interagao de diferentes formas e tratamentos de superficie na carga de ruptura de uma vitrocerámica reforgada com dissilicato de litio reparada com compósito nanoparticulado. Materials e Método A superficie superior de espécimes de vitroceramica (IPS e.max Press, Ivoclar Vivadent) foi preparada com tres formas (plana, plato único, ou duplo) e recebeu (n=11): 'nenhum tratamento', 'condicionamento com ácido hidrofluoridrico 5%', ou 'jateamento com AfOf. Ambos espécimes condicionados e jateados receberam silano e adesivo universal. Todos os espécimes foram reparados incrementalmente com compósito (Filtek Z350, 3M ESPE) até6 mm acima do plato cerámico mais alto, armazenados em saliva artificial á 37 °C por 21 dias, e submetidos á 1.000 termociclos (5 e 55 °C). A interface compósito-cerámica de cada amostra foi testada á tragao até sua falha em máquina universal e o modo de falha foi determinado com estereomicroscópio. A morfologia da superficie de uma amostra representativa de forma/tratamento de superficie foi observada através de microscopia eletronica de varredura (MEV). Resultados Independentemente da forma ceramica, a ausencia de tratamento superficial resultou em valores de carga de ruptura significativamente menores. Nao foi observada differenga significativa entre os espécimes planos condicionados ou jateados; no entanto, o condicionamento resultou em valores significativamente maiores que o jateamento para espécimes com plato único e duplo. A maioria (60%) dos espécimes condicionados e com plato único ou duplo apresentou falhas mistas. Imagens SEM demonstraram rugosidade superficial mais regular dos espécimes condicionados que os jateados. Conclusoes O tratamento superficial de uma restauragao defeituosa de vitrocerámica reforgada por dissilicato de litio tem maior influencia na retengao do reparo de compósito do que sua forma macroscópica; ainda, o condicionamento com ácido hidrofluoridrico parece proporcionar maior resistencia de uniao ao reparo com compósito.

RESUMEN

OBJECTIVE: to evaluate the existing evidence on surface treatment techniques employed in resin composite repair and their effect on the repair short- and long-term bond strength. DATA AND SOURCE: This scoping review was performed under the PRISMA-ScR guidelines for scoping reviews and registered on the Open Science Framework platform. STUDY SELECTION: A systematic search was conducted in PubMed, Embase, and Scopus and grey literature up to September 2022 without language or date restriction. In vitro studies comparing mechanical surface and/or chemical treatments on repair bond strength of resin composite were included. Studies evaluating experimental adhesive systems or resin composites were excluded. Selection of studies and data extraction were performed. Data from selected studies was qualitatively analyzed. RESULTS: A total of 76 studies were included in the qualitative analysis. Among the mechanical treatments, alumina blasting was the most frequently used, followed by silica coating and diamond bur. As for chemical treatments, dentin bonding systems were the most frequently evaluated, followed by universal adhesive systems and silane/ceramic primer. The combination of mechanical and chemical pre-treatments increased the repair bond strength of resin composite in both short- and long-term simulated aging scenarios. The evidence obtained from the included studies was classified as moderate quality, mainly due to the medium risk of bias observed across most of the studies. CONCLUSION: The techniques used to treat the surface of resin composites for repair are diverse. Incorporating a combination of mechanical and chemical pre-treatments resulted in superior repair bond strength of resin composite materials under both short- and long-term simulated aging conditions. CLINICAL SIGNIFICANCE: The analysis of evidence revealed significant variability among protocols for repairing resin composites. Utilizing both mechanical and chemical pre-treatment methods is important for enhancing the bond strength of resin composites during both short- and long-term simulated aging situations.

Asunto(s)

RESUMEN

Abstract: This in vitro study aimed to evaluate the repair bond strength of resin-modified glass ionomer cement using either the same material or a universal adhesive in the etch-and-rinse and self-etch modes plus resin composite. Twenty-four resin-modified glass ionomer cement blocks were stored in distilled water for 14 d and thermocycled. Sandpaper ground specimens were randomly assigned to three experimental groups according to the repair protocol: resin-modified glass ionomer cement (Riva Light Cure, SDI) and universal adhesive (Scotchbond Universal Adhesive, 3M Oral Care) in etch-and-rinse or self-etch modes and nanohybrid resin composite (Z350 XT, 3M Oral Care). After 24 h of water storage, the blocks were sectioned, and bonded sticks were subjected to the microtensile bond strength (μTBS) test. One-way ANOVA and Tukey's test were used to analyze the data. The failure mode was descriptively analyzed. The highest μTBS values were obtained when the resin-modified glass ionomer cement was repaired using the same material (p < 0.01). In addition, the mode of application of the universal adhesive system did not influence the repair bond strength of the resin-modified glass ionomer cement. Adhesive/mixed failures prevailed in all groups. Repair of resin-modified glass ionomers with the same material appears to be the preferred option to improve bond strength.

RESUMEN

Better understanding of dentists' decision-making about defective restorations is needed to close the evidence-practice gap (EPG). Aim: this study aimed to quantify the EPG about defective restorations and identify dentist factors associated with this EPG. Methods: 216 dentists from São Paulo State, Brazil, completed a questionnaire about three clinical case scenarios involving defective composite restorations with cementum-dentin margins (case 1) and enamel margins (case 2), and an amalgam (case 3) restoration. Dentists were asked what treatment, if any, they would recommend, including preventive treatment, polishing, re-surfacing, or repairing the restoration, or replacing the entire restoration. Replacing the entire restoration in any of these three scenarios was classified as inconsistent with the evidence, comprising an EPG. Bivariate analyses using Chi-square, ANOVA, or multiple comparison tests were performed (p<.05). Results: for defective composite restorations, 49% and 55% of dentists chose to replace the entire restoration for cases 1 and 2, respectively. Twenty-nine percent of dentists chose to replace the entire amalgam restoration. Dentists were significantly more likely to choose to replace the defective amalgam restoration than the composite restoration with a defect at the cementum-dentin margins or the enamel margins (both at p < .001). Female dentists were more likely to choose a conservative treatment than male dentists for cases 1 (p=.034) and 2 (p=.009). Dentists with a higher percentage of patients interested in individualized caries prevention were also more conservative in case 1 (p=.045). Conclusion: a substantial EPG regarding treatment decisions for defective restorations exists, especially for composite restorations. This study adds to the international evidence that an EPG exists in this clinical area and that global strategies need to be developed to close the gap.

RESUMEN

Background: The goal of this study is to determine the effect of different sandblasting particles and dental adhesive systems on the repair strength of dimethacrylate-based composite resins. Materials and Methods: In this in-vitro study, 96 specimens of X-trafil composite blocks were prepared and divided into eight groups (n = 12). Four groups were sandblasted with Aluminum Oxide (AL) and four other groups with Bio-Active Glass particles (BAG). A two-component silane was applied on the surface of all the samples after phosphoric acid etching and rinsing. Two groups of the sandblasted specimens were treated with Clearfil SE Bond (CSB) and the other two groups were treated with Single Bond Universal (SBU) and new composite was bonded to the prepared surfaces. Half of the specimens in each group were thermocycled. Shear force was applied to the bonded composite using a universal testing machine with a crosshead speed of 0.5 mm/min and mean shear bond strength (MSBS) was calculated (MPa). The data was analyzed using Kruskal-Wallis and Man-Whitney U-tests with the significance level of 0.05. Results: Significant differences were observed between different groups (P < 0.001). The highest and the lowest MSBS of the thermocycled samples were reported 18.88 MPa with application of AL and SBU and 11.46 MPa with the application of AL and CSB, respectively. No significant difference was observed with application of BAG particles after thermocycling. Conclusion: Effect of AL on repair shear bond strength of composite resins is affected by bonding type. Bonding type did not affect repair shear bond strength of BAG. Thermocycling reduced bond strength in all groups.

RESUMEN

BACKGROUND: Using a rotary instrument or ultrasonic instrument for tooth preparation is a basic operation in the dental clinic that can produce a significant number of droplets and aerosols. The dental droplet and aerosol can lead to the transfer of harmful germs. The goal of this study was to analyze the properties of microbiological aerosol created by droplets and aerosol generated by three common tooth-preparation instruments. METHODS: Streptococcus mutans UA159 was used as the biological tracer to visualize the droplets and aerosols. The passive sampling method was used to map the three-dimensional spatial distribution and the six-stage Andersen microbial sampler (AMS) was used as the active sampling method to catch aerosol particles at a specific time. RESULTS: The aerosol concentration is related to instruments, three-dimensional spatial distribution, and dissipation time. Most aerosols were generated by air turbines. More microorganisms are concentrated at the 1.5 m plane. The majority of the post dental procedure contamination was detected within the 0-10-min period and it decreased rapidly within 30 min. CONCLUSION: This study is conducive to the proposal and improvement of relevant infection control measures in dental procedures and provides a basis for the assessment of measures, reducing the risk of nosocomial infection.

Asunto(s)

RESUMEN

BACKGROUND: Despite increasing evidence, dentists have not widely adopted repairs. The authors aimed to develop and test potential interventions targeting dentists' behavior. METHODS: Problem-centered interviews were performed. Emerging themes were linked to the Behavior Change Wheel to develop potential interventions. The efficacy of 2 interventions was then tested in a postally delivered behavioral change simulation trial among German dentists (n = 1,472 per intervention). Dentists' stated repair behavior regarding 2 case vignettes was assessed. Statistical analysis was performed using McNemar test, Fisher exact test, and a generalized estimating equation model (P < .05). RESULTS: Two interventions (guideline, treatment fee item) were developed on the basis of identified barriers. A total of 504 dentists participated in the trial (17.1% response rate). Both interventions significantly changed dentists' behavior toward repairs of composite and amalgam restorations, respectively (guideline: difference [Δ] = +7.8% and Δ = +17.6%, treatment fee item: Δ = +6.4% and Δ = +31.5%; adjusted P < .001). Dentists were more likely to consider repairs if they already performed repairs frequently (odds ratio [OR], 1.23; 95% CI, 1.14 to 1.34) or sometimes (OR, 1.08; 95% CI, 1.01 to 1.16), if they regarded repairs as highly successful (OR, 1.24; 95% CI, 1.04 to 1.48), if their patients preferred repairs over total replacements (OR, 1.12; 95% CI, 1.03 to 1.23), for partially defective composite restorations (OR, 1.46; 95% CI, 1.39 to 1.53), and after receiving 1 of the 2 behavioral interventions (OR, 1.15; 95% CI, 1.13 to 1.19). CONCLUSIONS: Systematically developed interventions targeting dentists' repair behaviors are likely efficacious to promote repairs. PRACTICAL IMPLICATIONS: Most partially defective restorations are replaced completely. Effective implementation strategies are required to change dentists' behavior. This trial was registered at https://www. CLINICALTRIALS: gov. The registration number is NCT03279874 for the qualitative phase and NCT05335616 for the quantitative phase.

Asunto(s)

RESUMEN

Purpose: To evaluate color differences in repair of indirect ceramic and resin nanoceramic CAD/CAM blocks with two universal shade composites after different surface preparations. Materials and methods: 120 samples were prepared from IPS Empress and GC Cerasmart270 CAD/ CAM blocks and thermocycled (5000 cycles, 5°C-55°C). Initial colors of sample surfaces were measured using a spectrophotometer. Rectangular prism-shaped cavities were prepared and repaired with Tokuyama Universal Bond/Omnichroma and G-Multiprimer/G-Premio/Essentia Universal following surface preparation with aluminum oxide, Cojet, and bioactive glass (Sylc). Repaired samples were thermocycled (5000 cycles) and color measurement was performed. Color coordinates L*a*b* were recorded, and color differences were calculated using the CIELab formula. Color differences between pre-and post-repair (ΔE1) and between post-repair and post-aging (ΔE2) were determined. Data were analyzed using Three-way ANOVA with a significance level set at p<0.05. Results: ΔE1 values in all subgroups exceeded the threshold of 3.3. No significant difference was found between the surface preparation processes regarding ΔE1 values. There was no significant difference between the composites and bonding agents in ΔE1 values, except for Cerasmart/Sylc and Empress/Sylc groups. No statistically significant difference was detected in ΔE2 values between the surface preparation treatments in all groups. (p >0.05). Conclusion: Color match of the universal shade composites, which are preferred to increase the esthetic satisfaction and to simplify repair procedures, were found above the acceptable threshold. Post-aging color stability of universal shade composites was below the acceptable threshold.

RESUMEN

OBJECTIVES: The aim was to investigate aspects of the teaching of restoration repair as a minimally invasive alternative to replacing defective direct composite restorations in undergraduate curricula teaching programs in Brazilian dental schools. METHODS: A 14-item validated survey questionnaire was mailed to directors/coordinators of operative/restorative dentistry teachers of Brazilian Dental Schools. Data were collected on demographic characteristics of the teachers and institutions, together with questions on the teaching of the repair of defective resin-based composite restorations as part of the school curriculum; the rationale behind the teaching; the nature of the teaching (preclinical and/or clinical); how techniques were taught, indications for repair, operative techniques, materials used, patient acceptability and expected longevity of completed repairs. RESULTS: Two hundred and twenty-two (94%) directors/ coordinators of dental curricula in Brazil were contacted. One hundred and thirty-one directors/coordinators (59%) replied, providing the e-mail address from the teacher responsible for the operative/restorative dentistry program in their school. Of these, 104 responded to the questionnaire (79% response rate). Ninety-three (89%) of the participating schools reported teaching composite repairs as an alternative to replacing restorations. Of the theoretical content, 43% was taught at preclinical and clinical levels, whereas most practical experience (53%) was acquired at clinical levels. Eighty-eight schools (95%) reported tooth substance preservation being the main reason for teaching repair techniques. All schools that taught repairs reported high patient acceptability. CONCLUSIONS: The teaching of composite restoration repair as an alternative to restoration replacement is established in undergraduate programs in most of the Brazilian dental schools surveyed. CLINICAL SIGNIFICANCE: The reasons for teaching restoration repair in Brazil were found to be quite unanimous among teachers, especially regarding the preservation of tooth structure. Variations were found in the clinical indications for repair, suggesting the need for further investigations. Monitoring repaired restorations should be encouraged and could contribute to future studies.

Asunto(s)

RESUMEN

To evaluate shade matching ability of one-shade composites used for repair of different resin-based restorative materials. Two one-shade composites or one layering composite of 1 mm thickness were placed over non-aged or aged 3 different base materials of 1 mm thickness to simulate repair. Two millimeters thick base samples were prepared and used for reference (n=12). Shade measurements of reference and repair groups were performed with dental spectrophotometer and color difference (ΔE00) were calculated according to CIEDE2000. Data were analyzed using three-way ANOVA followed by Tukey's test (α=0.05). Regardless of aging and base materials, repairing with layering composite yielded lower ΔE00 than repair of one-shade composites (p<0.05). Repair of non-aged and aged GrandioDisc with any repair composite led to higher ΔE00 values than repair of other base materials (p<0.05). Shade matching performance of one-shade composites for repair of different non-aged or aged resin-based material was not clinically acceptable.

Asunto(s)

RESUMEN

Objectives: The purpose of this study was to compare the effect of plasma irradiation and other surface preparation methods on the microtensile bond strength of repaired resin composites. Materials and Methods: Twenty molds of a universal nanohybrid composite were prepared, aged and subjected to thermocycling. The specimens were divided into 5 groups for surface preparations including, C (Control): application of GC G-Premio Bond (GP) only; SB: sandblasting with alumina and GP; SI: application of phosphoric acid etching, silane, and unfilled resin; RB: roughening by diamond bur, phosphoric acid etching and GP; PL: application of argon and atmosphere plasma and then GP. The specimens were repaired with the new resin composite, cut to 1mm2 beam, and then subjected to thermocycling. The microtensile bond strengths were measured using a universal testing machine. The failure modes were assessed with a stereomicroscope. Data were analyzed using two-way ANOVA and Tukey's test. The level of significance was α=0.05. Results: The highest mean bond strength was found for the application of universal bonding GC GP in controls (26.62MPa) and the lowest average bond strength belonged to the SI groups (9.06MPa). The difference in the mean bond strength between the SI group and other groups was significant (P<0.05). The failure mode of specimens in all groups was predominantly adhesive. Conclusion: The application of GP as an intermediate universal adhesive established a proper bond between the old and new resin composite. In addition, the plasma application and other surface preparation methods did not significantly improve the bond strength.

RESUMEN

Better understanding of dentists' decision-making about defective restorations is needed to close the evidence-practice gap (EPG). This study aimed to quantify the EPG about defective restorations and identify dentist factors associated with this EPG. Methods: 216 dentists from São Paulo State, Brazil, completed a questionnaire about three clinical case scenarios involving defective composite restorations with cementum-dentin margins (case 1) and enamel margins (case 2), and an amalgam (case 3) restoration. Dentists were asked what treatment, if any, they would recommend, including preventive treatment, polishing, re-surfacing, or repairing the restoration, or replacing the entire restoration. Replacing the entire restoration in any of these three scenarios was classified as inconsistent with the evidence, comprising an EPG. Bivariate analyses using Chi-square, ANOVA, or multiple comparison tests were performed (p<.05). Results: for defective composite restorations, 49% and 55% of dentists chose to replace the entire restoration for cases 1 and 2, respectively. Twenty-nine percent of dentists chose to replace the entire amalgam restoration. Dentists were significantly more likely to choose to replace the defective amalgam restoration than the composite restoration with a defect at the cementum-dentin margins or the enamel margins (both at p < .001). Female dentists were more likely to choose a conservative treatment than male dentists for cases 1 (p=.034) and 2 (p=.009). Dentists with a higher percentage of patients interested in individualized caries prevention were also more conservative in case 1 (p=.045). Conclusion: a substantial EPG regarding treatment decisions for defective restorations exists, especially for composite restorations. This study adds to the international evidence that an EPG exists in this clinical area and that global strategies need to be developed to close the gap

Asunto(s)

RESUMEN

OBJECTIVES: This study aimed to investigate the influence of the respective mechanical and chemical pre-treatments on the composite repair of a CAD/CAM hybrid ceramic using a microtensile bond strength test (µTBS). METHODS: 15 CAD/CAM Blocks of Vita Enamic (VE) were randomly sectioned into three mechanical pre-treatments: (1.) Diamond bur (D), (2.) Airborne abrasion (A), (3.) Tribochemical silica coating (T) and subsequently five chemical pre-treatments: (1.) Clearfil SE Bond Bond (B; negative control), (2.) ESPE Sil (S), (3.) Clearfil Ceramic Primer Plus (CPP), (4.) Clearfil Repair (CR) and (5.) Scotchbond Universal (SCB). Per block, n = 20 specimens were sawn. Half of the specimens were randomly selected and subjected to an immediate bond strength test, while the other half was subjected to artificial aging for 6 months 180 days at 37 °C and subsequent thermocycling of 5000 cycles. A µTBS was performed and data (MPa) were compared in one-way and two-way ANOVA and Tukey's HSD. Paired-t-test was used for artificial aging (α = 0.05). Debonded specimens were analyzed of for failure modes with a stereomicroscope (SEM). RESULTS: The results of one-way ANOVA for the fifteen fastening procedures after aging indicated significant differences according to SCB-A and CPP-T. Two-way ANOVA after aging observed inferior bond strength for SCB. No differences were observed for mechanical pre-treatments. Artificial aging showed a significant reduction in bond strength on most of the fastening procedures. SIGNIFICANCE: SCB showed the lowest bond strength values besides B, S, CPP, and CR. MDP and silane are both suitable for the repair of VE.

Asunto(s)

RESUMEN

Aim: The aim of this in vitro study was to compare nine different bonding agents of so-called universal type with one well-recognized, 3-step etch-and-rinse bonding agent, as control, in a composite-to-composite shear bond strength (SBS) test. Materials and methods: Cylindrical composite substrates were made according to manufacturers' specifications and potted in epoxy according to the description in ISO TS 29022:2003. They were stored in water (37 °C) for 2 months (for water sorption). New composite was bonded to the substrates using nine different bonding agents of universal type, and one 3-step etch-and-rinse bonding agent as control. Fifteen specimens were made for each bonding agent as required by ISO 29022. SBS testing was performed as described in the standard. Vertical load was applied at the speed of 1 mm/min, using a universal testing machine. Two test series were performed: (A) Short term test of SBS after 2 weeks (B) Long term test of SBS after 1-year storage of specimens in water at 37 °C. Results: Test results for the short term test (A); composite-to-composite SBS mean values ranged from 12.0 to 24.9 MPa, and for the long term test (B), SBS ranged from 11.4 to 25 MPa. Six universal bonding agents showed significantly higher bond strength than control in 1-year test. Conclusion: In this in vitro study, testing shear bond strength of composite-to-composite bonding, the universal bonding agents performed similar and for some agents better than the 3-step etch-and-rinse bonding agent. New simplified bonding procedures seem reliable for repair of composite.

RESUMEN

This study aimed to report the reasons for replacement of direct composite resin restorations in dental practices in Brazil. The study used a convenience sample of 213 dentists. A questionnaire was developed from previously validated instruments and sent electronically to prospective participants. The questions pertained to professional characteristics; criteria most frequently used in determining whether a direct composite resin restoration warranted replacement; and respondents' choice of treatment options (maintain, repair, or replace the restoration) in various clinical scenarios based on FDI World Dental Federation evaluation criteria, which are categorized into 3 groups: esthetic, functional, and biological properties. The descriptive statistical analysis was conducted using percentage frequencies, and associations between variables were tested using chi-square tests (α = 0.05). According to 47.9% of respondents, staining was the esthetic property that most often warranted replacement. For the functional property, 53.8% of respondents reported that fracture of material and retention was the most important factor indicating the need for replacement. For the clinical scenarios, 41.7% of respondents chose restoration replacement when evaluating esthetic properties, 59.8% when evaluating functional properties, and 64.4% when evaluating biological properties. Replacement, rather than maintenance or repair, was the most frequently reported clinical decision, and the dentists' professional profiles influenced treatment recommendations, with specialists exhibiting a slightly lower frequency of recommendations for replacement of direct composite resin restorations.

Asunto(s)

RESUMEN

OBJECTIVE: This study aimed to systematically review the literature to compare the risk of failure of repaired and replaced defective direct resin composite and amalgam restorations performed in permanent teeth. MATERIALS AND METHODS: The PubMed/MEDLINE, Scopus, Lilacs, BBO, Web of Science, SciELO, Cochrane Central Register of Controlled Trials (CENTRAL) databases, and gray literature were searched to identify longitudinal clinical studies related to the research question. No publication year or language restriction was considered. Two authors independently selected the studies, extracted the data, and assessed the risk of bias and certainty of evidence. A meta-analysis was performed using a fixed effects model at a 5% significance level. RESULTS: From 1224 potentially eligible studies, thirteen were selected for full-text analysis, and three were included in the systematic review and meta-analysis. There was no difference in the risk of failure of repaired and replaced defective direct restorations (RR: 1.21, 95% CI: 0.51-2.83), either for resin composite (p = 0.97) or amalgam (p = 0.51) restorations. The risk of bias was high and the certainty of evidence was very low. CONCLUSION: Based on the very low certainty of evidence, the repair of direct restorations does not present a significant difference in the risk of failure when compared to replacements in permanent teeth. CLINICAL RELEVANCE: Restoration repair is a procedure that is included in the minimal intervention principle for improvement of tooth longevity in that the risk of failure of repaired partially defective restorations in permanent teeth seems similar to that of replacement. Further studies are required before definitive conclusions can be drawn.

Asunto(s)

RESUMEN

OBJECTIVES: This 10-year practice-based study aimed to compare survival and success of direct resin composite and ceramic veneers placed in a private dental practice, between January 2008 and March 2014. METHODS: Data were retrieved from a clinical practice's records and were anonymized typed into electronic files. All veneer information was recorded, including previous restorations, repairs or failures, materials used, dates, patient, and age. RESULTS: We analyzed 1459 veneer restorations, of which 1043 (71.5%) were direct composite, and 416 (28.5%) were ceramic, placed in 341 patients. The mean patients' age was 47.8 years, and the mean number of restorations per patient was 4.3 restorations. During all follow-up, 957 (65.6%) veneers were successful without any repair, 252 (17.3%) were repaired and still in place, and 250 (17.1%) had a failure that resulted in replacement. Replacements were usually carried out with the same material placed at first. Considering success analysis, annual failure rates (AFR) for veneers in 5 and 10 years were 9.1% and 10% for direct composite and 2.9% and 2.8% for ceramic, respectively. Survival analysis showed AFR of 3.9% and 4.1% for composite and 1.4% and 1.2% for ceramic at the same periods. Cox regression was made for both success and survival outcomes. Composite veneers presented a higher risk of failure than ceramic veneers with higher hazard ratios for survival (HR) [HR 4.00 (2.74-5.83)] and success [HR 5.16 (2.65-10.04)]. SIGNIFICANCE: Ceramic veneers had superior longevity than direct composite veneers in both success and survival analysis.

Asunto(s)