RESUMEN
Nanoribbons (NRs), leveraging the flexibility of one-dimensional materials and the expansive surface area of two-dimensional materials, offer heightened exposure to edge sites and superior charge transfer rates. Consequently, they present promising prospects within the domain of photocatalysis. Crystalline red phosphorus (cRP), dcharacterized by its layered and fibrous structure, lends itself readily to the production of nanoribbons. Our study demonstrates a robust method for achieving high-yield, high-quality cRP by concurrently introducing mineralizing agent I2 and Si wafers into the Chemical Vapor Transport (CVT) synthesis process. Through ultrasound assistance, we transformed high-quality cRP into crystalline red phosphorus nanoribbons (cRP NRs) with an average thickness ranging from 7.5 to 17.5 nm and an average width between 75 and 175 nm. cRP NRs (I2 and Si) showcased impressive degradation capabilities towards Methyl Orange (MO) and Tetracycline (TC), achieving a remarkable 99% degradation of MO within 18 min under the simulated visible-light irradiation. The reactive species capturing experiments confirmed that ·O2- was the primary active agent responsible for the photocatalytic degradation of MO.
Asunto(s)
Compuestos Azo , Fósforo , Tetraciclina , Tetraciclina/química , Fósforo/química , Compuestos Azo/química , Catálisis , Nanotubos de Carbono/químicaRESUMEN
Red phosphorus anode, attributed to its high specific capacity of 2596 mAh g-1, is expected to improve the energy density of Na-ion batteries. However, the P anode currently is unsatisfactory for practical usage due to the large volume expansion beyond 300%, which brings out uncontrolled brittle failure. To address this challenge, we here design a nacre-like phosphorus anode by resilient graphene oxide staggered together. The staggered structure simultaneously offers mechanical strength and interwoven toughness. Finite element modeling reveals that the sodiation stress from P nanoparticles will be transferred into interlayer pillars as the elastic medium to release sodiation stress. The prepared anode achieves an ultrahigh areal capacity of 13 mAh cm-2 at a mass loading of 5.8 mg cm-2. Notably, the volume change of the anode is limited to approximately 8.2% at full sodiation, significantly lower than that of the traditional phosphorus electrodes.
RESUMEN
Crystalline red phosphorus(CRP), known for its promising photocatalytic properties, faces challenges in photocatalytic hydrogen evolution(PHE) due to undesired inherent charge deep trapping and recombination effects induced by defects. This study overcomes these limitations through an innovative strategy in integrating ruthenium single atoms(Ru1) within CRP to simultaneously repair the intrinsic undesired vacancy defects and serve as the uniformly distributed anchoring sites for a controllable growth into ruthenium nanoparticles(RuNP). Hence, a highly functionalized CRP with Ru1 and RuNP(Ru1-NP/CRP) with concerted effects in regulating electronic structures and promoting interfacial charge transfer has been achieved. Advanced characterizations unveil the pioneering dual role of pre-anchored Ru1 in transforming CRP photocatalysis. The regulations of vacancy defects on the surface of CRP minimize the detrimental deep charge trapping, resulting in the prolonged lifetime of charges. With the well-distributed in-situ growth of RuNP on Ru1 sites, the constructed robust "bridge" that connects CRP and RuNP facilitates constructive interfacial charge transfer. Ultimately, the synergistic effect induced by the pre-anchored Ru1 endows Ru1-NP/CRP with an exceptional PHE rate of 3175µmolh-1g-1, positioning it as one of the most efficient elemental-based photocatalysts. This breakthrough underscores the crucial role of pre-anchoring metal single atoms at defect sites of catalysts in enhancing hydrogen production.
RESUMEN
All-solid-state lithium-ion batteries (ASSLIBs) using sulfide electrolytes and high-capacity alloy-type anodes have attracted sizable interest due to their potential excellent safety and high energy density. Encapsulating insulating red phosphorus (P) inside nanopores of a carbon matrix can adequately activate its electrochemical alloying reaction with lithium. Therefore, the porosity of the carbon matrix plays a crucial role in the electrochemical performance of the resulting red P/carbon composites. Here, we use zeolite-templated carbon (ZTC) with monodisperse micropores and mesoporous carbon (CMK-3) with uniform mesopores as the model hosts of red P. Our results reveal that micropores enable more effective pore utilization for the red P loading, and the P@ZTC material can achieve a record-high content (65.0 wt %) of red P confined within pores. When used as an anode of ASSLIBs, the P@ZTC electrode delivers an ultrahigh capacity of 1823 mA h g-1 and a high initial Coulombic efficiency of 87.44%. After 400 deep discharge-charge cycles (running over 250 days) at 0.2 A g-1, the P@ZTC electrode still holds a reversible capacity of 1260 mA h g-1 (99.92% capacity retention per cycle). Moreover, a P@ZTC||LiNi0.8Co0.1Mn0.1O2 full cell can deliver a reversible areal capacity of over 3 mA h cm-2 at 0.1C after 100 cycles.
RESUMEN
Potassium ion batteries (PIBs) are a viable alternative to lithium-ion batteries for energy storage. Red phosphorus (RP) has attracted a great deal of interest as an anode for PIBs owing to its cheapness, ideal electrode potential, and high theoretical specific capacity. However, the direct preparation of phosphorus-carbon composites usually results in exposure of the RP to the exterior of the carbon layer, which can lead to the deactivation of the active material and the production of "dead phosphorus". Here, the advantage of the π-π bond conjugated structure and high catalytic activity of metal phthalocyanine (MPc) is used to prepare MPc@RP/C composites as a highly stable anode for PIBs. It is shown that the introduction of MPc greatly improves the uneven distribution of the carbon layer on RP, and thus improves the initial Coulombic efficiency (ICE) of PIBs (the ICE of FePc@RP/C is 75.5% relative to 62.9% of RP/C). The addition of MPc promotes the growth of solid electrolyte interphase with high mechanical strength, improving the cycle stability of PIBs (the discharge-specific capacity of FePc@RP/C is 411.9 mAh g-1 after 100 cycles at 0.05 A g-1). Besides, density functional theory theoretical calculations show that MPc exhibits homogeneous adsorption energies for multiple potassiation products, thereby improving the electrochemical reactivity of RP. The use of organic molecules with high electrocatalytic activity provides a universal approach for designing superior high-capacity, large-volume expansion anodes for PIBs.
RESUMEN
The therapy of the clear cell renal cell carcinoma (ccRCC) is crucial for the human healthcare due to its easy metastasis and recurrence, as well as resistance to radiotherapy and chemotherapy. In this work, we propose the synthesis of MoS2@red phosphorus (MoS2@RP) heterojunction to induce synergistic photodynamic and photothermal therapy (PDT/PTT) of ccRCC. The MoS2@RP heterojunction exhibits enhanced spectra absorption in the NIR range and produce local heat-increasing under the NIR laser irradiation compared with pure MoS2 and RP. The high photocatalytic activity of the MoS2@RP heterojunction contributes to effective transferring of the photo-excited electrons from the RP to MoS2, which promotes the production of various types of radical oxygen species (ROS) to kill the ccRCC cells. After the NIR irradiation, the MoS2@RP can effectively induce the apoptosis in the ccRCC cells through localized hyperthermia and the generation of ROS, while exhibiting low cytotoxicity towards normal kidney cells. In comparison to MoS2, the MoS2@RP heterojunction shows an approximate increase of 22â¯% in the lethality rate of the ccRCC cells and no significant change in toxicity towards normal cells. Furthermore, the PDT/PTT treatment using the MoS2@RP heterojunction effectively eradicates a substantial number of deep-tissue ccRCC cells in vivo without causing significant damage to major organs. This study presents promising effect of the MoS2@RP heterojunction-based photo-responsive therapy for effective ccRCC treatment.
Asunto(s)
Carcinoma de Células Renales , Disulfuros , Neoplasias Renales , Molibdeno , Fósforo , Fotoquimioterapia , Terapia Fototérmica , Molibdeno/química , Molibdeno/farmacología , Humanos , Disulfuros/química , Disulfuros/farmacología , Disulfuros/síntesis química , Fósforo/química , Fósforo/farmacología , Neoplasias Renales/patología , Neoplasias Renales/terapia , Neoplasias Renales/tratamiento farmacológico , Carcinoma de Células Renales/patología , Carcinoma de Células Renales/terapia , Carcinoma de Células Renales/tratamiento farmacológico , Animales , Apoptosis/efectos de los fármacos , Ratones , Supervivencia Celular/efectos de los fármacos , Especies Reactivas de Oxígeno/metabolismo , Ensayos de Selección de Medicamentos Antitumorales , Fármacos Fotosensibilizantes/farmacología , Fármacos Fotosensibilizantes/química , Fármacos Fotosensibilizantes/síntesis química , Antineoplásicos/farmacología , Antineoplásicos/química , Antineoplásicos/síntesis química , Tamaño de la Partícula , Línea Celular Tumoral , Proliferación Celular/efectos de los fármacos , Rayos Infrarrojos , Propiedades de SuperficieRESUMEN
Red phosphorus (RP), the one of the most prospective anodes in lithium-ion batteries (LIBs), has been severely limited due to the intrinsic defects of massive volume expansion and low electronic conductivity. The vaporization-condensation-conversion (VCC), which confines RP nanoparticles into carbon host, is the most widely used method to address the above drawbacks and prepare RP/C nanostructured composites. However, the volume effect-dominated RP caused by the inevitably deposition of RP vapor on the surface of carbon material suffers from the massive volume change and unstable solid electrolyte interface (SEI) film. Herein, we propose a simple interfacial modification method to eliminate the superficial RP and yield stable surface composed of ion-conducting Li3PS4 solid electrolyte, endowing RP/AC composites excellent cycling performance and ultrafast reaction kinetics. Therefore, the RP/AC@S composites exhibit 926 mAh/g after 320 cycles at 0.2 A/g (running over 181 days), with 81.6 % capacity retention and a corresponding capacity decay rate of as low as 0.059 %. When coupled with LiFePO4 cathode, the full cells present superior cycling performance (62.1 mAh/g after 500 cycles at 1 A/g) and excellent rate capability (81.1 mAh/g at 1.0 A/g).
RESUMEN
Quasi-one-dimensional (quasi-1D) van der Waals crystal fibrous red phosphorus (RP) exhibits pronounced in-plane optical anisotropy, positioning it as a potential candidate for polarization-related micro-nano devices. Unfortunately, a comprehensive investigation into the complex refractive index of fibrous RP and the structure-activity relationship connecting the distinctive quasi-1D structure with optical anisotropy is currently deficient. Herein, we have collectively determined the complex refractive index of the fibrous RP flakes within the ab-plane through Kramers-Kronig (KK) analysis and theoretical calculation. Notably, the maximum birefringence of fibrous RP reaches 0.642@475â nm with an absolute extinction coefficient of only 0.08, superior to the reported traditional optical crystals and the emerging low-dimensional materials as well. The remarkable birefringence can be attributed to the synergistic influence of the large electronic dipole polarizability, anisotropic electron density distribution and the distortion of stereochemically active lone pair (SCALP). This work demonstrates the potential of fibrous RP for polarization-sensitive devices, illuminating possibilities to exploit novel giant birefringent crystals based on the structure-activity relationship.
RESUMEN
Red phosphorus (P) as an anode material of potassium-ion batteries possesses ultra-high theoretical specific capacity (1154 mAh g-1 ). However, owing to residual white P during the preparation and sluggish kinetics of K-P alloying limit its practical application. Seeking an efficient catalyst to address the above problems is crucial for the secure preparation of red P anode with high performance. Herein, through the analysis of the activation energies in white P polymerization, it is revealed that the highest occupied molecular orbital energy of I2 (-7.40 eV) is in proximity to P4 (-7.25 eV), and the lowest unoccupied molecular orbital energy of I2 molecule (-4.20 eV) is lower than that of other common non-metallic molecules (N2 , S8 , Se8 , F2 , Cl2 , Br2 ). The introduction of I2 can thus promote the breaking of the PâP bond and accelerate the polymerization of white P molecules. Besides, the ab initio molecular dynamics simulations show that I2 can enhance the kinetics of P-K alloying. The as-obtained red P/C composites with I2 deliver excellent cycling stability (358 mAh g-1 after 1200 cycles at 1 A g-1 ). This study establishes catalysis as a promising pathway to tackle the challenges of P anode for alkali metal ion batteries.
RESUMEN
MXene nanosheets and ordered porous carbons both have their own advantages and disadvantages. Assembling and combining the advantages of the two will be a good choice for battery electrode hosts of active materials. In this work, an electrostatic separation-adsorption strategy is proposed to realize the ordered alternating self-assembly of MXene nanosheets and ordered porous carbon (MPOC), obtaining a unique wall-like porous material with a high conductivity and interconnected porous nanostructure, which strengthens the transfer rate of electrons and ions simultaneously. Meanwhile, the introduction of N-doping from porous carbon into MPOC prolongs the cycle life. When use red phosphorus (RP) as active materials, the MPOC@RP anode exhibited high-capacity output (2454.3 and 2408.1 mAh g-1 in lithium-ion batteries (LIBs) and sodium-ion batteries (SIBs) at 0.1 C) and long cycle life (the decay rates per cycle of 0.028% and 0.036% after 1500 and 1200 cycles at 2 C in LIBs and SIBs respectively). The successful application in RP anodes displays great potential in other electrode materials such as silicon, sulfur, selenium, and so on. Meanwhile, this strategy is also effective to design other composites materials like MXene and carbon nanotubes, MXene and Graphene, and so on.
RESUMEN
Red phosphorus (rP) is one of the most promising anode materials for lithium-ion batteries, owing to its high theoretical capacity. However, its low electronic conductivity and large volume expansion during cycling limit its practical applications, as it exhibits low electrochemical activity and unstable cyclability. To address these problems, tellurium (Te)-rP-C composites, which have active materials (Te, rP) that are uniformly distributed within the carbon matrix, were fabricated through a simple high-energy ball milling method. Among the three electrodes, the Te-rP (1:2)-C electrode with a 5% FEC additive delivers a high initial CE of 80% and a high reversible capacity of 734 mAh g-1 after 300 cycles at a current density of 100 mA g-1. Additionally, it exhibits a high-rate capacity of 580 mAh g-1 at a high current density of 10,000 mA g-1. Moreover, a comparison of the electrolytes with and without the 5% FEC additive demonstrated improved cycling stability when the FEC additive was used. Ex situ XRD analysis demonstrated the lithiation/delithiation mechanism of Te-rP (1:2)-C after cycling based on the cyclic voltammetry results. Based on the electrochemical impedance spectroscopy analysis results, a Te-rP-C composite with its notable electrochemical performance as an anode can sufficiently contribute to the battery anode industry.
RESUMEN
The recycling of spent graphite from waste lithium-ion batteries (LIBs) holds great importance in terms of environmental protection and conservation of natural resources. In this study, a simple two-step method involving heat treatment and solution washing was employed to recycle spent graphite. Subsequently, the recycled graphite was milled with red phosphorus to create a carbon/red phosphorus composite that served as an anode material for the new LIBs, aiming to address the low capacity issue. In a half-cell configuration, the carbon/red phosphorus composite exhibited remarkable cycling stability, maintaining a capacity of 721.7 mAh g-1 after 500 cycles at 0.2 A g-1, and demonstrated an excellent rate performance with a capacity of 276.2 mAh g-1 at 3 A g-1. The improved performance can be attributed to the structure of the composite, where the red phosphorus particles are covered by the carbon layer. This composite outperformed pure recycled graphite, highlighting its potential in enhancing the electrochemical properties of LIBs. Furthermore, when the carbon/red phosphorus composite was assembled into a full-cell configuration with LiCoO2 as the cathode material, it displayed a stable electrochemical performance, further validating its practical applicability. This work presents a promising and green strategy for recycling spent graphite and using it in the production of new batteries. The findings offer a high potential for commercialization, contributing to the advancement of sustainable and ecofriendly energy storage technologies.
RESUMEN
Ammonia borane (AB) holds great promise for chemical hydrogen storage, but its slow dehydrogenation kinetics under ambient conditions requires a suitable catalyst to facilitate hydrogen production from AB. Here, we fabricated binary red phosphorus/graphitic carbon nitride (RP/g-CN) heterojunctions decorated with Pt nanoparticles (NPs, denoted Pt/RP/g-CN) with a facile ultrasound-assisted two-step protocol as a photo-assisted catalyst for the hydrolysis of AB (HAB). The heterojunction established through intimate P-O-N bonds was proven to have improved photophysical properties such as a lower electron-hole recombination and enhanced visible light utilization compared to the pristine components. With the incorporation of Pt NPs, the optical properties of RP/g-CN heterojunctions were further improved through Schottky junction formation between semiconductors and Pt NPs, enabling a superb hydrogen gas (H2) generation rate of 142 mol H2·mol Pt-1·min-1 under visible light irradiation. Even though g-CN is a well-known host material for many metal NPs, here we discovered that the interaction of Pt NPs with RP in the ternary heterojunction structure is more favorable than that of g-CN, stressing the key role of RP as a support material in the designed ternary heterostructure. The band alignment of the ternary heterojunction catalyst along with the flow of charge carriers was also studied and shown to be a type-II heterojunction structure without hole migration, namely, a complex type-II heterojunction. Several scavenger experiments were also conducted to explain the mechanism of the photo-assisted HAB. To the best of our knowledge, this is the first example of a dual mechanism proposed for the visible light-assisted HAB. While the majority of the H2 was believed to be produced on the Pt NPs surface with the traditional B-N bond dissociation mechanism, the strong oxidizing action of OH⢠radicals formed by the heterojunction photocatalyst was also speculated to account for the 33% increase in the activity upon visible light irradiation through another mechanism.
RESUMEN
Elemental phosphorus exhibits fascinating structural varieties and versatile properties. The unique nature of phosphorus bonds can lead to the formation of extremely complex structures, and detailed structural information on some phosphorus polymorphs is yet to be investigated. In this study, we investigated an unidentified crystalline phase of phosphorus, type-II red phosphorus (RP), by combining state-of-the-art structural characterization techniques. Electron diffraction tomography, atomic-resolution scanning transmission electron microscopy (STEM), powder X-ray diffraction, and Raman spectroscopy were concurrently used to elucidate the hidden structural motifs and their packing in type-II RP. Electron diffraction tomography, performed using individual crystalline nanowires, was used to identify a triclinic unit cell with volume of 5330â Å3 , which is the largest unit cell for elemental phosphorus crystals up to now and contains approximately 250 phosphorus atoms. Atomic-resolution STEM imaging, which was performed along different crystal-zone axes, confirmed that the twisted wavy tubular motif is the basic building block of type-II RP. Our study discovered and presented a new variation of building blocks in phosphorus, and it provides insights to clarify the complexities observed in phosphorus as well as other relevant systems.
RESUMEN
Transition metal (TM) single atom catalysts (SACs) are of great potential for photocatalytic H2 production because of their abundant catalytic active sites and cost-effectiveness. As a promising support material, red phosphorus (RP) based SACs are still rarely investigated. In this work, we have carried out systematic theoretical investigations by anchoring TM atoms (Fe, Co, Ni, Cu) on RP for efficient photocatalytic H2 generation. Our density functional theory (DFT) calculations have revealed that 3d orbitals of TM locate close to the Fermi level to guarantee efficient electron transfer for photocatalytic performances. Compared with pristine RP, the introduction of single atom TM on the surface exhibit narrowed bandgaps, resulting in easier spatial separation for photon-generated charge carriers and an extended photocatalytic absorption window to the NIR range. Meanwhile, the H2O adsorptions are also highly preferred on the TM single atoms with strong electron exchange, which benefits the subsequent water-dissociation process. Due to the optimized electronic structure, the activation energy barrier of water-splitting has been remarkably reduced in RP-based SACs, revealing their promising potential for high-efficiency H2 production. Our comprehensive explorations and screening of novel RP-based SACs will offer a good reference for further designing novel photocatalysts for high-efficiency H2 generation.
RESUMEN
In order to obtain sulfur-containing organophosphorus compounds that are promising as extractants of heavy metals, the interaction of elemental phosphorus and sulfur with alkyl bromides catalyzed using strong bases was studied. According to the task, the reaction of non-toxic and non-flammable red phosphorus with alkyl bromides under conditions of phase transfer catalysts (PTC), followed by the introduction of elemental sulfur into the reaction medium, were studied. It is shown that alkyl bromides interact with red phosphorus when heated (95-105 °C, 5-8 h) under conditions of phase transfer catalysts (PTC) in a two-phase system: a 60% aqueous solution of KOH-toluene-benzyltriethylammonium chloride (BTEAC) forming a mixture of organophosphorus compounds along with alkylphosphines (57-60%), are the main reaction products; alkylphosphine oxides are also formed (40-43%). The introduction of elemental sulfur (solution in toluene) at the final stage of the process into the reaction mass cooled to 40-60 °C leads to the expected alkylphosphine sulfides, which are the result of the interaction of alkylphosphines with sulfur. The formation of complex mixtures of products prevents the release of target alkylphosphine sulfides in individual form. However, the synthesized mixture of alkylphosphine sulfides and alkylphosphine oxides without separation into individual components is promising for studying its extraction properties in relation to heavy metals. Testing of the extraction properties of synthesized mixtures of alkylphosphine sulfides and alkylphosphine oxides in relation to heavy metals (Ni, Co, Zn, Pb) and noble metals (Ag) showed that the resulting mixtures of tertiary phosphine oxides and phosphine sulfides are highly effective extractants. The degree of extraction in relation to Ni, Co, Zn, and Pb varies from 99.90 to 99.99%, and for Ag from 99.56 to 99.59%.
RESUMEN
Red phosphorus (RP) is a promising anode material for use in lithium-ion batteries (LIBs) due to its high theoretical specific capacity (2596 mA h g-1). However, the practical use of RP-based anodes has been challenged by the material's low intrinsic electrical conductivity and poor structural stability during lithiation. Here, we describe a phosphorus-doped porous carbon (P-PC) and disclose how the dopant improves the Li storage performance of RP that was incorporated into the P-PC (designated as RP@P-PC). P-doping porous carbon was achieved using an in situ method wherein the heteroatom was added as the porous carbon was being formed. The phosphorus dopant effectively improves the interfacial properties of the carbon matrix as subsequent RP infusion results in high loadings, small particle sizes, and uniform distribution. In half-cells, an RP@P-PC composite was found to exhibit outstanding performance in terms of the ability to store and utilize Li. The device delivered a high specific capacitance and rate capability (1848 and 1111 mA h g-1 at 0.1 and 10.0 A g-1, respectively) as well as excellent cycling stability (1022 mA h g-1 after 800 cycles at 2.0 A g-1). Exceptional performance metrics were also measured when the RP@P-PC was used as an anode material in full cells that contained lithium iron phosphate as the cathode material. The methodology described can be extended to the preparation of other P-doped carbon materials that are employed in contemporary energy storage applications.
RESUMEN
The toxicity and carcinogenicity of Cr(VI) makes it a major threat to the health of animals and people. However, how to efficiently remove Cr(VI) still faces important challenges. In this study, a new metal-free polypyrrole-red phosphorus (PPy-RP) composite is successfully synthesized by in-situ oxidation polymerization for Cr(VI) removal from wastewater. The maximum adsorption capacity (qm) of Cr(VI) on PPy-RP-1 is 513.2 mg/g when the pH value is 2, which is far superior to RP nanosheets (207.8 mg/g) and PPy (294.9 mg/g). The improved qm can be ascribe to the good dispersion and increased specific surface area of PPy-RP adsorbent. Encouragingly, PPy-RP adsorbent still exhibits excellent stability after 7 cycles tests without a significant decline in removal efficiency, and remain above 81.4%. Based on the fittings of adsorption isotherms and kinetics, the process conforms to the pseudo-first-order kinetic model and the single-layer adsorption of the Langmuir model with an R2 value of 0.98533. The adsorption process is chemical and monolayer. The experimental result demonstrates that the PPy-RP can efficient removal Cr(VI) by electrostatic attraction and complexation reaction (formation of N-Cr(VI) bond) through the PPy on the surface. The results of this study indicate that PPy-RP is a promising adsorbent to remove the Cr(IV).
Asunto(s)
Cromo , Polímeros , Contaminantes Químicos del Agua , Animales , Adsorción , Cromo/análisis , Cromo/química , Concentración de Iones de Hidrógeno , Cinética , Fósforo/química , Polímeros/química , Pirroles/química , Contaminantes Químicos del Agua/análisisRESUMEN
The current photocatalytic bactericidal materials in the field of food pathogen control are usually consisted of metals that always suffering from poor stability and possible secondary pollution. Besides, the requirement for high energy excitation also inspires the enthusiasm on exploring non-metallic catalysts. Herein, the non-metallic composite of rice shell biochar loaded with red phosphorus (B@RP) was developed for photocatalysis and photothermal removal of bacteria. The B@RP showed effective photocatalysis performance to stimulate the generation of OH and O2- free radicals for the elimination of Escherichia coli (E. coli). At the same time, the photothermal effect of B@RP can also increase the permeability of cell membrane, which is conducive to free radicals entering the cell interior. Therefore, the non-metallic composite could achieve complete removal of E. coli within 2 h under illumination. Meanwhile, B@RP had excellent stability and the sterilization efficiency maintained 100% after 9 cycles. Hence, B@RP is expected to be a harmless and efficient bactericidal material for food industry.
Asunto(s)
Escherichia coli , Oryza , Fósforo , Antibacterianos/farmacología , CatálisisRESUMEN
With the rapid expansion of the market scale for indium phosphide (InP) semiconductors in high-tech industries such as optoelectronics and solar energy, the generation of hazardous waste InP has also increased dramatically, and the task of recycling waste InP is urgent. However, InP as a representative phosphide semiconductor is prone to produce highly toxic substances such as yellow phosphorus and PH3 in the recycling process, which discourages most companies from using it. In this study, a safe and efficient method of "vacuum decomposition-directional condensation (VD-DC)" is proposed to recover valuable materials from waste InP. In this method, briquetting pretreatment is used to improve thermal conductivity. At a decomposition temperature of 1123 K, system pressure of 30 Pa, and holding time of 3.5 h, indium with a purity of 99.43 wt% is obtained, and the direct yield reaches 98.54%. Non-toxic and stable red phosphorus with a purity of 98.14 wt% is recovered by converting the condensed yellow phosphorus at 573 K. Vacuum technology significantly reduces the decomposition temperature of InP and avoids the emission of waste water and waste gas, thus operating in an environmentally friendly manner.