RESUMEN
Cu3BiS3 thin films are fabricated via spin coating of precursor solutions containing copper and bismuth xanthates onto planar glass substrates or mesoporous metal oxide scaffolds followed by annealing at 300 °C to convert the metal xanthates into copper bismuth sulfide. Detailed insights into the film formation are gained from time-resolved simultaneous small and wide angle X-ray scattering measurements. The Cu3BiS3 films show a high absorption coefficient and a band gap of 1.55 eV, which makes them attractive for application in photovoltaic devices. Transient absorption spectroscopic measurements reveal that charge generation yields in mesoporous TiO2/Cu3BiS3 heterojunctions can be significantly improved by the introduction of an In2S3 interlayer, and long-lived charge carriers (t50% of 10 µs) are found.
RESUMEN
The synthesis, characterization, and thermogravimetric analysis of tris(N,N'-di-isopropylacetamidinate)molybdenum(III), Mo(iPr-AMD)3, are reported. Mo(iPr-AMD)3 is a rare example of a homoleptic mononuclear complex of molybdenum(III) and fills a longstanding gap in the literature of transition metal(III) trisamidinate complexes. Thermogravimetric analysis (TGA) reveals excellent volatilization at elevated temperatures, pointing to potential applications as a vapor phase precursor for higher temperature atomic layer deposition (ALD), or chemical vapor deposition (CVD) growth of Mo-based materials. The measured TGA temperature window was 200-314 °C for samples in the 3-20 mg range. To validate the utility of Mo(iPr-AMD)3, we demonstrate aerosol-assisted CVD growth of MoO3 from benzonitrile solutions of Mo(iPr-AMD)3 at 500 °C using compressed air as the carrier gas. The resulting films are characterized by X-ray photoelectron spectroscopy, X-ray diffraction, and Raman spectroscopy. We further demonstrate the potential for ALD growth at 200 °C with a Mo(iPr-AMD)3/Ar purge/300 W O2 plasma/Ar purge sequence, yielding ultrathin films which retain a nitride/oxynitride component. Our results highlight the broad scope utility and potential of Mo(iPr-AMD)3 as a stable, high-temperature precursor for both CVD and ALD processes.
RESUMEN
Focused electron beam-induced deposition (FEBID) and focused ion beam-induced deposition (FIBID) are direct-write fabrication techniques that use focused beams of charged particles (electrons or ions) to create 3D metal-containing nanostructures by decomposing organometallic precursors onto substrates in a low-pressure environment. For many applications, it is important to minimize contamination of these nanostructures by impurities from incomplete ligand dissociation and desorption. This spotlight on applications describes the use of ultra high vacuum surface science studies to obtain mechanistic information on electron- and ion-induced processes in organometallic precursor candidates. The results are used for the mechanism-based design of custom precursors for FEBID and FIBID.
RESUMEN
A heat-up method for quantum dots (QDs) synthesis holds distinctive benefits for large-scale production with its simplicity, scalability, and high reproducibility. Its applications, however, have been limited because it inevitably yields a strong overlap between the nucleation and the growth stages. We addressed this long-standing problem by introducing a precursor having separated reaction paths for nucleation and growth. Unlike existing precursors, which employ a shared intermediate for both reactions, 9-mercapto-9-borabicyclo[3.3.1]nonane (BBN-SH) induces growth via surface-assisted conversion and drives nucleation via cluster formation in solution. Furthermore, this precursor chemistry embeds an efficient mechanism to suppress nucleation during growth. As such, BBN-SH allows heat-up-based growth of high-quality shells that are comparable to those created by the injection method. It is also notable that BBN-SH-based heat-up synthesis shows mitigated sensitivity to temperature fluctuation; therefore, it is highly suitable for industrial-scale reactions. We established a simple, scalable, and economic scheme for core/shell QDs by streamlining quantitative core synthesis and heat-up-based shell growth and showed that the scheme produces QDs of comparable quality to those produced by the traditional method. Here, we introduce a precursor that drives a distinctive mode of nanoparticle growth. We anticipate our study to inspire the design of other precursors and unleash the full potential of heat-up synthesis.
RESUMEN
Organic-inorganic metal halide perovskite solar cells (PSCs) have recently been considered as one of the most competitive contenders to commercial silicon solar cells in the photovoltaic field. The deposition process of a perovskite film is one of the most critical factors affecting the quality of the film formation and the photovoltaic performance. A hot-casting technique has been widely implemented to deposit high-quality perovskite films with large grain size, uniform thickness, and preferred crystalline orientation. In this review, we first review the classical nucleation and crystal growth theory and discuss those factors affecting the hot-casted perovskite film formation. Meanwhile, the effects of the deposition parameters such as temperature, thermal annealing, precursor chemistry, and atmosphere on the preparation of high-quality perovskite films and high-efficiency PSC devices are comprehensively discussed. The excellent stability of hot-casted perovskite films and integration with scalable deposition technology are conducive to the commercialization of PSCs. Finally, some open questions and future perspectives on the maturity of this technology toward the upscaling deposition of perovskite film for related optoelectronic devices are presented.
RESUMEN
The composition, crystallinity, morphology, and trap-state density of halide perovskite thin films critically depend on the nature of the precursor solution. A fundamental understanding of the liquid-to-solid transformation mechanism is thus essential to the fabrication of high-quality thin films of halide perovskite crystals for applications such as high-performance photovoltaics and is the topic of this Review. The roles of additives on the evolution of coordination complex species in the precursor solutions and the resulting effect on perovskite crystallization are presented. The influence of colloid characteristics, DMF/DMSO-free solutions and the degradation of precursor solutions on the formation of perovskite crystals are also discussed. Finally, the general formation mechanism of perovskite thin films from precursor solutions is summarized and some questions for further research are provided.
RESUMEN
The utilization of metal alkoxides as single-source precursors for (mixed-)oxide materials offers remarkable benefits, such as the possibility to precisely control the metal ratio in the resulting material, highly homogeneous distribution of the elements in the film, and the low temperatures required for film processing. Herein we report on the isolation and characterization of the bimetallic Co-Mo alkoxide [Co3 Mo4 O10 (OCH3 )10 (dmf)4 ] (Co3 Mo4 ; dmf=N,N-dimethylformamide), which was prepared by the anion metathesis reaction of the corresponding metal chlorides. The Co-Mo alkoxide was explored as a well-defined precursor of cobalt oxide catalysts for the oxygen evolution reaction (OER) in alkaline electrolyte MOH. The catalysts demonstrated excellent activity in the OER, manifested in low onset potentials and Tafel slopes and superb stability under the operating conditions both in alkaline and nearly neutral media. It was observed that the nature of the metal cation of the alkaline electrolyte MOH (M+ =Li+ , Na+ , K+ , Cs+ ) greatly affected the catalytic performance of the material. We propose that the positive effect of larger metal cations on the film activity in the OER could be explained by the higher hydration enthalpies of larger ions and enhanced mass transport within a larger interlayer space between the [CoO2 ]δ-∞ sheets of the in situ formed binary oxides. It may be deduced that this trend is universal and may be extended to other types of metal oxides forming layered structures during the OER.
RESUMEN
The compatibility of atomic layer deposition directly onto the mixed halide perovskite formamidinium lead iodide:methylammonium lead bromide (CH(NH2)2, CH3NH3)Pb(I,Br)3 (FAPbI3:MAPbBr3) perovskite films is investigated by exposing the perovskite films to the full or partial atomic layer deposition processes for the electron selective layer candidates ZnO and SnOx. Exposing the samples to the heat, the vacuum, and even the counter reactant of H2O of the atomic layer deposition processes does not appear to alter the perovskite films in terms of crystallinity, but the choice of metal precursor is found to be critical. The Zn precursor Zn(C2H5)2 either by itself or in combination with H2O during the ZnO atomic layer deposition (ALD) process is found to enhance the decomposition of the bulk of the perovskite film into PbI2 without even forming ZnO. In contrast, the Sn precursor Sn(N(CH3)2)4 does not seem to degrade the bulk of the perovskite film, and conformal SnOx films can successfully be grown on top of it using atomic layer deposition. Using this SnOx film as the electron selective layer in inverted perovskite solar cells results in a lower power conversion efficiency of 3.4% than the 8.4% for the reference devices using phenyl-C70-butyric acid methyl ester. However, the devices with SnOx show strong hysteresis and can be pushed to an efficiency of 7.8% after biasing treatments. Still, these cells lacks both open circuit voltage and fill factor compared to the references, especially when thicker SnOx films are used. Upon further investigation, a possible cause of these losses could be that the perovskite/SnOx interface is not ideal and more specifically found to be rich in Sn, O, and halides, which is probably a result of the nucleation during the SnOx growth and which might introduce barriers or alter the band alignment for the transport of charge carriers.
RESUMEN
Identification and synthesis of intramolecularly donor-stabilized aluminium(III) complexes, which contain a 3-(dimethylamino)propyl (DMP) ligand, as novel atomic layer deposition (ALD) precursors has enabled the development of new and promising ALD processes for Al2 O3 thin films at low temperatures. Key for this promising outcome is the nature of the ligand combination that leads to heteroleptic Al complexes encompassing optimal volatility, thermal stability and reactivity. The first ever example of the application of this family of Al precursors for ALD is reported here. The process shows typical ALD like growth characteristics yielding homogeneous, smooth and high purity Al2 O3 thin films that are comparable to Al2 O3 layers grown by well-established, but highly pyrophoric, trimethylaluminium (TMA)-based ALD processes. This is a significant development based on the fact that these compounds are non-pyrophoric in nature and therefore should be considered as an alternative to the industrial TMA-based Al2 O3 ALD process used in many technological fields of application.
RESUMEN
Engineering the chemical composition of organic and inorganic hybrid perovskite materials is one of the most feasible methods to boost the efficiency of perovskite solar cells with improved device stability. Among the diverse hybrid perovskite family of ABX3 , formamidinium (FA)-based mixed perovskite (e.g., FA1-x Csx PbI3 ) possesses optimum bandgaps, superior optoelectronic property, as well as thermal- and photostability, which is proven to be the most promising candidate for advanced solar cell. Here, FA0.9 Cs0.1 PbI3 (Cl) is implemented as the light-harvesting layer in planar devices, whereas a low temperature, two-step solution deposition method is employed for the first time in this materials system. This paper comprehensively exploits the role of Cs+ in the FA0.9 Cs0.1 PbI3 (Cl) perovskite that affects the precursor chemistry, film nucleation and grain growth, and defect property via pre-intercalation of CsI in the inorganic framework. In addition, the resultant FA0.9 Cs0.1 PbI3 (Cl) films are demonstrated to exhibit an improved optoelectronic property with an elevated device power conversion efficiency (PCE) of 18.6%, as well as a stable phase with substantial enhancement in humidity and thermal stability, as compared to that of FAPbI3 (Cl). The present method is able to be further extended to a more complicated (FA,MA,Cs)PbX3 material system by delivering a PCE of 19.8%.
RESUMEN
A series of boron-modified polyorganosilazanes was synthesized from a poly(vinylmethyl-co-methyl)silazane and controlled amounts of borane dimethyl sulfide. The role of the chemistry behind their synthesis has been studied in detail by using solid-state NMR spectroscopy, FTIR spectroscopy, and elemental analysis. The intimate relationship between the chemistry and the processability of these polymers is discussed. Polymers with low boron contents displayed appropriate requirements for facile processing in solution, such as impregnation of host carbon materials, which resulted in the design of mesoporous monoliths with a high specific surface area after pyrolysis. Polymers with high boron content are more appropriate for solid-state processing to design mechanically robust monolith-type macroporous and dense structures after pyrolysis. Boron acts as a crosslinking element, which offers the possibility to extend the processability of polyorganosilazanes and suppress the distillation of oligomeric fragments in the low-temperature region of their thermal decomposition (i.e., pyrolysis) at 1000 °C under nitrogen. Polymers with controlled and high ceramic yields were generated. We provide a comprehensive mechanistic study of the two-step thermal decomposition based on a combination of thermogravimetric experiments coupled with elemental analysis, solid-state NMR spectroscopy, and FTIR spectroscopy. Selected characterization tools allowed the investigation of specific properties of the monolith-type SiBCN materials.
RESUMEN
Monolith-type titanium nitride/silicon nitride nanocomposites, denoted as TiN/Si3 N4 , have been prepared by a reaction of polysilazanes with a titanium amide precursor, warm pressing of the resultant polytitanosilazanes, and subsequent pyrolysis of the green bodies at 1400 °C. Initially, a series of polytitanosilazanes was synthesized and the role of the chemistry behind their synthesis was studied in detail by using solid-state NMR spectroscopy, elemental analysis, and molecular-weight measurements. The intimate relationship between the chemistry and the processability of these precursors is discussed. Polytitanosilazanes display the appropriate requirements for facile processing in solution and as a melt, but they must be treated with liquid ammonia to be adapted for solid-state processing, that is, warm-pressing, to design dense and mechanically stable structures after pyrolysis. We provide a comprehensive mechanistic study of the nanocomposite conversion based on solid-state NMR spectroscopy coupled with thermogravimetric experiments. HRTEM images coupled with XRD and Raman spectroscopy confirmed the unique nanostructural features of the nanocomposites, which appear to be a result of the molecular origin of the materials. The as-obtained samples are composed of an amorphous Si3 N4 matrix, in which TiN nanocrystals are homogeneously formed in situ in the matrix during the process. The hardness and Young moduli were measured and are discussed.
RESUMEN
A template-assisted polymer-derived ceramic route is investigated for preparing a series of silicoboron carbonitride (Si/B/C/N) foams with a hierarchical pore size distribution and tailorable interconnected porosity. A boron-modified polycarbosilazane was selected to impregnate monolithic silica and carbonaceous templates and form after pyrolysis and template removal Si/B/C/N foams. By changing the hard template nature and controlling the quantity of polymer to be impregnated, controlled micropore/macropore distributions with mesoscopic cell windows are generated. Specific surface areas from 29 to 239â m(2) g(-1) and porosities from 51 to 77 % are achieved. These foams combine a low density with a thermal insulation and a relatively good thermostructural stability. Their particular structure allowed the in situ growth of metal-organic frameworks (MOFs) directly within the open-cell structure. MOFs offered a microporosity feature to the resulting Si/B/C/N@MOF composite foams that allowed increasing the specific surface area to provide CO2 uptake of 2.2 %.
RESUMEN
Cu2 S/ZnS heterostructured nanorods (HNRs) with uncommon morphologies are achieved through single-pot and multi-batch synthetic strategies. In both cases, Cu2 S NRs form first, which then undergo partial cation exchange and solution-liquid-solid (SLS)-like growth catalyzed by the remaining Cu2 S parts of the NRs. The location and the volume of ZnS achieved through partial cation exchange control the size of the Cu2 S catalysts, which in turn determine whether tapered rod-rod, body/tail, or barbell-like structure results from subsequent SLS-like growth. Concurrent cation exchange can sometimes cause Cu2 S catalysts to be lost during SLS-like growth, leading to further diversity in achievable morphologies of Cu2 S/ZnS HNRs. Additional insights are gained on how parameters such as Zn precursor, ligand choice, and concentration alter cation exchange and SLS-like growth steps.
RESUMEN
Modification of different zirconium propoxide precursors with H(2)dea was investigated by characterization of the isolated modified species. Upon modification of zirconium n-propoxide and [Zr(O(n)Pr)(O(i)Pr)(3)((i)PrOH)](2) with (1/2) a mol equivalent of H(2)dea the complexes [Zr(2)(O(n)Pr)(6)(OCH(2)CH(2))(2)NH](2) (1) and [Zr(2)(O(n)Pr)(2)(O(i)Pr)(4)(OCH(2)CH(2))(2)NH](2) (2) were obtained. However, (1)H-NMR studies of these tetranuclear compounds showed that these are not time-stable either in solution or solid form. The effect of this time instability on material properties is demonstrated by light scattering and TEM experiments. Modification of zirconium isopropoxide with either (1/2) or 1 equivalent mol of H(2)dea results in formation of the trinuclear complex, Zr{eta(3)mu(2)-NH(C(2)H(4)O)(2)}(3)[Zr(O(i)Pr)(3)](2)(iPrOH)(2) (3) countering a unique nona-coordinated central zirconium atom. This complex 3 is one of the first modified zirconium propoxide precursors shown to be stable in solution for long periods of time. The particle size and morphology of the products of sol-gel synthesis are strongly dependent on the time factor and eventual heat treatment of the precursor solution. Reproducible sol-gel synthesis requires the use of solution stable precursors.