RESUMEN

Cranial prostheses are frequently required for patients with cranial defects secondary to trauma, decompressive craniectomy, or other pathologies. When the resected or craniotomized bone cannot be reused, cranioplasty with artificial materials offers both aesthetic and protective benefits. However, high-end custom-made options, like polyether ether ketone or titanium prostheses, are expensive and not widely available. Heat-cured polymethyl methacrylate (PMMA) prostheses are generally preferred over their cold-cured counterparts. In-house dental laboratories can provide a cost-effective and practical solution by employing a lost-wax technique akin to denture fabrication, utilizing a three-dimensional printed custom open mold. Fabricating large heatcured PMMA cranioplasts presents certain challenges, such as the need for large flasks and potential porosity. These can be overcome by using a large stainless steel container (a tiffin box) and M-Seal epoxy to ensure an airtight curing process. This method can be easily adopted by standard dental laboratories. At our center, four patients have successfully fitted with cranioplasty prostheses produced using this technique. Even though the patients are outside of the scope of this technical note all of them indicated high satisfaction, and no complications were reported. This straightforward approach demonstrates that in-house, heat-cured PMMA cranioplasts can represent a viable, cost-effective option for cranial reconstruction.

RESUMEN

Sarcoidosis and complications related to fillers have been reported following the COVID-19 vaccination. Additionally, cutaneous sarcoidosis has been observed around polymethyl methacrylate (PMMA) injection sites. Foreign-body reactions to PMMA can occur simultaneously with systemic sarcoidosis, suggesting a shared pathogenic mechanism between both conditions. To report a case of sarcoidosis and PMMA granulomas following COVID-19 vaccination (ChAdOx11), successfully treated with tofacitinib. We present a 59-year-old woman who developed systemic sarcoidosis and a granulomatous reaction to PMMA filler following the COVID-19 vaccination (ChAdOx11). Notably, both PMMA and the vaccine were potential triggers for sarcoidosis. Treatment with tofacitinib produced marked improvement in both the cutaneous and pulmonary involvement of sarcoidosis and the granulomatous reaction to PMMA. This successful outcome suggests tofacitinib, a pan-JAK inhibitor, an alternative treatment for cutaneous and systemic sarcoidosis, as well as a potential therapy for granulomatous complications of dermal fillers, such as PMMA.

RESUMEN

Aim This study aims to evaluate the color stability of four provisional materials: polymethyl methacrylate (DPI® Self-Cure), 10-ethoxylated bisphenol A dimethacrylate (Oratemp® C&B), bis-acryl composite resin (Systemp® C&B, Ivoclar Vivadent), and bis-acryl composite (Systemp® C&B, Ivoclar Vivadent) combined with light-cure composite (Fusion Flo® LC). Materials and methods A total of 40 specimens were meticulously crafted from modeling wax into discs, each precisely 2 mm thick and 20 mm in diameter. Four provisional materials were packed into molds, yielding 10 specimens for each material group. After mixing and polymerization, the specimens were trimmed and polished. Reflectance spectrophotometers were used for initial color assessments based on the CIELAB color space system. Staining solutions, including coffee, Tata Green Tea, Pepsi, and turmeric, were prepared to mimic dietary agents. Artificial saliva, replicating oral conditions, was formulated and sterilized. The specimens were then immersed in various solutions for 15 days at 37 °C. Color measurements were taken on days 2 and 15 using the same spectrophotometer, calculating color differences (ΔE) from changes in L*, a*, and b* values. Results DPI Self-Cure (polymethyl methacrylate) was found to be the most color-stable temporary restorative material, followed by Vivadent (bis-acryl composite resin), Oratemp (10-ethoxylated bisphenol A dimethacrylate), and Fusion Flo (light-cure composite). Fusion Flo exhibited the highest color change by the 15th day. Coffee and green tea demonstrated the greatest potential for causing color changes in the provisional restorative materials. Conclusion DPI Self-Cure exhibited the highest color stability among the provisional materials, with Vivadent and Oratemp following closely behind. Green tea and coffee were the most potent staining agents, while Pepsi and turmeric induced lesser color changes.

RESUMEN

Although dual implant constructs have recently been explored with promising results in very distal periprosthetic femur fractures (PPKF), the gold standard treatment of Rorabeck and Taylor type III PPKF remains a distal femur replacement or a highly constrained rotating hinge implant. However, this surgery is very aggressive and expensive for functionally low-demanding elderly patients. A new surgical technique using locking plates with polymethyl methacrylate cement augmentation is described to retain the femoral component avoiding its replacement. Four patients were treated and followed up for more than one year postoperative without any complications, their femoral component was retained without any loosening and the mobility in the Barthel Index remained unchanged.

RESUMEN

Aim: The present randomized clinical trial is aimed at evaluating clinical efficiency of two different types of esthetic crowns-polymethyl methacrylate crowns and vacuum formed thermoformed crown as an alternative to full-coverage coronal restoration for deciduous molars. Materials and methods: A total of 45 primary molars in pediatric patients were selected using randomization and split into three groups based on the technique used for preparation of crowns: group I-polymethyl methacrylate crowns; group II-thermoformed crown; and group III-stainless steel crowns (SSC). All crowns were clinically and radiographically evaluated at baseline, 1st month, and 3rd month for gingival health, retention, marginal integrity, proximal contacts, occlusion, alignment, and staining. Statistical analysis: The data was tabulated and analyzed by Statistical Package for the Social Sciences (SPSS) Version 23.0 software. The intergroup comparison was done by Kruskal-Wallis test, analysis of variance (ANOVA), and Mann-Whitney U test for continuous data. The intragroup comparison was done by Friedman test and Wilcoxon signed-rank test for categorical data. All p-values < 0.05 were considered statistically significant. Results: With regard to the parameters of plaque score, gingival index score, occlusion, interproximal contacts, retention, alignment, and marginal adaptation, no statistical significance was noted between the three groups. However, with regard to the discoloration (staining) when the polymethyl methacrylate acrylic (PMMA) group was compared with thermoforming group, statistical significance was noted in 1st month with p-values of 0.04 and 0.03, respectively. On intragroup comparison, statistically significant values were obtained in SSC group for plaque score and thermoforming group for gingival index score. Clinical significance: The study concluded that the PMMA and thermoforming crowns can be used as an alternative to SSC for restoring the primary molars as they showed equivalent results to that of standard SSC. How to cite this article: Matha N, Kumar KS, Reddy BVT, et al. Comparative Evaluation of Polymethyl Methacrylate and Thermoforming Crowns as Semipermanent Crowns in Primary Molars: An In Vivo Study. Int J Clin Pediatr Dent 2024;17(S-1):S43-S54.

RESUMEN

BACKGROUND: Enhancing the antibacterial properties of polymethyl methacrylate (PMMA) dental resins is crucial in preventing secondary infections following dental procedures. Despite the necessity for such improvement, a universally applicable method for augmenting the antibacterial properties of PMMA without compromising its mechanical properties and cytotoxicity remains elusive. Consequently, this study aims to address the aforementioned challenges by developing and implementing a composite material known as zinc oxide/graphene oxide (ZnO/GO) nanocomposites, to modify the PMMA. METHODS: ZnO/GO nanocomposites were successfully synthesized by a one-step procedure and fully characterized by TEM, EDS, FTIR and XRD. Then the physical and mechanical properties of PMMA modified by ZnO/GO nanocomposites were evaluated through water absorption and solubility test, contact angle test, three-point bending tests, and compression test. Furthermore, the biological properties of the modified PMMA were evaluated by direct microscopic colony count method, crystal violet staining and CCK-8. RESULTS: The results revealed that ZnO/GO nanocomposites were successfully constructed. When the concentration of nanocomposites in PMMA was 0.2 wt. %, the flexural strength of the resin was increased by 23.4%, the compressive strength was increased by 31.1%, and the number of bacterial colonies was reduced by 60.33%. Meanwhile, It was found that the aging of the resin did not affect its antibacterial properties, and CCK-8 revealed that the modified PMMA had no cytotoxicity. CONCLUSION: ZnO/GO nanocomposites effectively improved the antibacterial properties of PMMA. Moreover, the mechanical properties of the resin were improved by adding ZnO/GO nanocomposites at a lower range of concentrations.

Asunto(s)

RESUMEN

Denture fractures are a common problem in dental practice, and their repair is considered a first option to restore their functional properties. However, the inter-material resistance may become compromised. Typically, the bond between these materials weakens. Therefore, various surface treatment methods may be considered to enhance their mechanical properties. Poly(methyl methacrylate) (PMMA) heat-polymerized resin (HPR) was used as the repaired material, cold-polymerized material (CPR) for the repairs, and different variants of alumina abrasive blasting (AB), methyl methacrylate (M), ethyl acetate (EA), methylene chloride (CH), and isopropyl alcohol (IA) treatments were applied. Finally, combined surface treatments were chosen and analyzed. Surface morphologies after treatments were observed by scanning electron microscopy and the flexural, shear, and impact strengths were tested. AB and chemical treatment with CH, M, and EA was used to improve all mechanical properties, and further improvement of the properties could be achieved by combining both types of treatments. Varied changes in surface morphologies were observed. Treatment with IA yielded less favorable results due to the low impact strength. The best results were achieved for the combination of AB and CH, but during the application of CH it was necessary to strictly control the exposure time.

RESUMEN

Introdução: O polimetilmetacrilato é um produto de preenchimento permanente. A injeção deste material na face pode levar a complicações. O objetivo deste estudo é determinar em uma série de casos o tempo mediano de ocorrência de complicações, as áreas mais comprometidas, os tipos de complicações e tratamentos mais realizados. Método: Foram estudados 209 casos de pacientes portadores de complicações relacionadas ao uso de polimetilmetacrilato na face que buscaram tratamento entre o período de janeiro de 2000 a junho de 2021. Os dados analisados foram sexo, idade, número de injeções, momento da aplicação, intervalo de tempo até surgir a complicação, tipo de complicação, região comprometida e tratamento realizado. Resultados: A idade média dos pacientes foi de 45 anos (23 a 79 anos). Destes, 172 eram mulheres e 37 homens. O número de aplicações variou de 1 a 5. O tempo mediano de surgimento de complicações foi de 71 meses. As regiões mais comprometidas foram a malar, em 102 pacientes; mandibular, em 100; e zigomática, em 91. Granuloma foi observado em 135 pacientes; edema, em 120; e inflamação, em 78. O tratamento mais realizado foi a injeção de corticoide, em 111 pacientes, seguido de remoção cirúrgica, em 40. Conclusão: Os resultados podem servir como base de conhecimento para uma melhor compreensão das complicações com o uso de polimetilmetacrilato na face.

Introduction: Polymethylmethacrylate is a permanent filler product. Injecting this material into the face can lead to complications. The objective of this study is to determine in a series of cases the median time for complications to occur, the most affected areas, the types of complications, and the treatments most performed. Method: 209 cases of patients with complications related to the use of polymethyl methacrylate on the face who sought treatment between the period of January 2000 and June 2021 were studied. The data analyzed were gender, age, number of injections, moment of application, interval time until the complication arises, type of complication, affected region, and treatment performed. Results: The average age of patients was 45 years (23 to 79 years). Of these, 172 were women and 37 men. The number of applications ranged from 1 to 5. The median time for complications to appear was 71 months. The most affected regions were the malar, in 102 patients; mandibular, in 100; and zygomatic, in 91. Granuloma was observed in 135 patients; edema, in 120; and inflammation, in 78. The most common treatment was corticosteroid injection, in 111 patients, followed by surgical removal, in 40. Conclusion: The results can serve as a knowledge base for a better understanding of complications with the use of polymethylmethacrylate in the face.

RESUMEN

OBJECTIVES: To evaluate the survival rate of minimally invasive semipermanent occlusal polymethyl methacrylate (PMMA) onlays/veneers in previous temporomandibular disorder (TMD) patients with severe tooth wear and with a loss of vertical dimension after up to 7 years. METHOD AND MATERIALS: This case series was designed as a follow-up evaluation with consecutive patient recruitment. All patients bearing the indication for this kind of rehabilitation were treated by the same clinician using the same adhesive methodology. The study included 22 patients (3 men/19 women), with a mean ± SD age of 50.7 ± 11.6 years. Controls followed within the first 4 weeks (and subsequently as required). Failure criteria included damage by fracture, chipping, and retention loss. Survival rates were determined based on the Kaplan-Meier analysis. RESULTS: 328 semipermanent occlusal/incisal veneers were included (142 maxillary/186 mandibular teeth). Almost 80% of the restorations were in place and in function when starting the follow-up treatment after 180 days; failures predominantly occurred within the first 3 to 6 months but proved reparable. Depending on the patients' priorities, scheduled replacements followed successively, and more than 65% did not show repair or any renewal needs for more than 360 days. CONCLUSION: Within the limitations of this study the survival rates of occlusal veneers made of PMMA were sufficiently high to allow for consecutive treatment of the respective teeth by means of permanent restorations while preserving the restored vertical dimension. In patients with severe tooth wear and a TMD history, semipermanent restorative therapy with occlusal PMMA onlays/veneers would seem a noteworthy option.

Asunto(s)

RESUMEN

This work reports on the possibility of using polydopamine (PDA) as a tool to immobilize bromoisobutyryl moieties at the surface of cellulose nanocrystals (CNCs) and initiate Surface Intitiated Atom Transfer Radical Polymerization (SI-ATRP) reactions from these sites. Two different strategies based on i) the stepwise modification of the CNCs with dopamine (DA) and α-bromoisobutyryl bromide (BiBB) (Protocol 1) and ii) the one-step treatment of the CNCs with a mixture of DA and BiBB-modified DA (Protocol 2), were compared. Only the CNC particles treated according to Protocol 1 guaranteed efficient anchoring of the SI-ATRP initiating sites in our experimental conditions (with limited impact on the CNCs crystalline structure), the coated layer being leached out by certain solvents in the case of Protocol 2. The brominated particles displaying the best performances were subsequently tested as potential ATRP macroinitiators, using methyl methacrylate (MMA) and styrene (St) as model monomers. Polymer-grafted particles were successfully obtained, with a grafting density twice as high for Sty as for MMA, demonstrating the validity of this strategy.

RESUMEN

Introduction: Our objective in this study was to prepare a novel type of polymethyl methacrylate (PMMA) bone cement, analyze its material properties, and evaluate its safety and antibacterial efficacy. Methods: A halamine compound methacrylate antibacterial PMMA bone cement containing an N-Cl bond structure was formulated, and its material characterization was determined with Fourier transform infrared spectroscopy (FT-IR) and 1H-NMR. The antibacterial properties of the material were studied using contact bacteriostasis and releasing-type bacteriostasis experiments. Finally, in vitro and in vivo biocompatibility experiments were performed to analyze the toxic effects of the material on mice and embryonic osteoblast precursor cells (MC3T3-E1). Results: Incorporation of the antibacterial methacrylate monomer with the N-halamine compound in the new antibacterial PMMA bone cement significantly increased its contact and releasing-type bacteriostatic performance against Staphylococcus aureus. Notably, at 20% and 25% additions of N-halamine compound, the contact and releasing-type bacteriostasis rates of bone cement samples reached 100% (p < 0.001). Furthermore, the new antibacterial bone cement containing 5%, 10%, and 15% N-halamine compounds showed good biocompatibility in vitro and in vivo. Conclusion: In this study, we found that the novel antibacterial PMMA bone cement with N-halamine compound methacrylate demonstrated good contact and releasing-type bacteriostatic properties against S. aureus. In particular, bone cement containing a 15% N-halamine monomer exhibited strong antibacterial properties and good in vitro and in vivo biocompatibility.

RESUMEN

This study continues the discussion on the surface modification of polymers using an atmospheric pressure plasma (APP) reactor in air. These results complement prior research focusing on nonpolar polymers. Polymers, such as polyethylene terephthalate, polyetheretherketone, and polymethyl methacrylate, containing structurally bonded oxygen are studied, representing a range of properties such as oxygen content, crystalline/amorphous structure, polarity, functionality, and aliphatic/aromatic structure. APP induces superior wetting properties on the hydrophilic polymer surfaces with rapid and uniform modification within 0.5 s of exposure. The amorphous structures undergo additional modification for longer exposure. Moreover, the aliphatic chain structures require longer plasma exposure to reach surface modification equilibrium. The polar polymers reach a limit level of modification corresponding to a minimum water contact angle of about 50°. The surface polarity increases on average by a factor of approximately two. The equilibrium values of the adhesion work attained after post-processing recovery fall within a limited range of about 100-120 mJ/m2. The enhancement of surface functionality through the creation of oxidized groups primarily depends on the initial oxygen content and reaches a limit of about 40 at.% oxygen. The surface properties of the treated polar surfaces exhibit good stability, comparable to that of the previously tested nonpolar polymers.

RESUMEN

Purpose: Fractal analysis is a mathematical tool which allows the evaluation of complex microstructural features within materials that cannot be expressed in traditional geometric terms. The purpose of this study is to quantify the differences in polymethylmethacrylate intravertebral cement spatial distribution patterns following vertebroplasty using fractal analysis through the examination of osteoporotic and malignant compression fractures. Methods: Frontal and lateral post-vertebroplasty radiographs were evaluated from 29 patients with osteoporotic and malignant compression fractures who underwent vertebroplasty. The individually treated vertebra were divided into osteoporotic (n = 35) and malignant groups (n = 41). Images underwent segmentation, thresholding, and binarization prior to fractal analysis. Fractal dimension and lacunarity values were derived from the region of interest in treated vertebrae using the "box-counting" and "gliding-box" techniques respectively using ImageJ. The mean values of both parameters were compared between the 2 groups. Results: The mean fractal dimension was significantly higher in the malignant vertebral compression fracture group (1.53 ± 0.08) compared to the osteoporotic group (1.34 ± 0.17; P < .001). Similarly, mean lacunarity values were significantly higher in the malignant fracture group (0.50 ± 0.09) compared to the osteoporotic group (0.37 ± 0.10; P < .001). Conclusions: Fractal dimension and lacunarity values of cement spatial distribution patterns obtained from the post-vertebroplasty radiographs can differentiate between benign osteoporotic and malignant vertebral compression fractures. This novel technique may be useful for evaluating cement spatial distribution patterns in spine augmentation procedures, although further research is warranted in this area.

RESUMEN

PURPOSE: Heat-activated polymethyl methacrylate (PMMA) is the most common and widely accepted denture base material. Two important drawbacks are the development of denture stomatitis and the high incidence of fracture of denture bases. The present study investigated the effect of adding 0.2% by weight of silver nanoparticles (AgNps) and using the autoclave method of terminal boiling on the flexural strength of heat-activated PMMA denture base resin. METHODS: A total of 40 samples of heat-activated PMMA blocks were divided into four groups, with 10 samples (n = 10) in each group. Group 1 consisted of unmodified heat-activated PMMA resin (PMMA-1) polymerized by the conventional method of terminal boiling (conventional curing); Group 2 consisted of 0.2% by weight AgNPs added to heat-activated PMMA resin (PMMA-2) polymerized by conventional curing; Group 3 consisted of PMMA-1 polymerized by the autoclave method of terminal boiling (autoclave curing); and Group 4 consisted of PMMA-2 polymerized by autoclave curing. The flexural strength was tested using a universal testing machine. Descriptive statistics were expressed as mean ± SD and median flexural strength. Kruskal-Wallis ANOVA with Mann-Whitney U post hoc test was applied to test for statistical significance between the groups. The level of significance was set at p<0.05. RESULTS: The results showed a statistically significant reduction in flexural strength in Group 2 compared to Group 1. The samples from Group 4 showed a statistically significant increase in flexural strength compared to Group 2. The Group 4 denture base had the highest flexural strength (115.72 ± 7.27 MPa) among the four groups, followed by Group 3 (104.16 ± 4.85 MPa). The Group 1 samples gave a flexural strength of 101.45 ± 3.13 MPa, and Group 2 gave the lowest flexural strength (85.98 ± 3.49 MPa) among the four groups tested. CONCLUSION: The reduction in flexural strength of the heat-activated PMMA denture base after adding 0.2% by weight of AgNP as an antifungal agent was a major concern among manufacturers of commercially available denture base materials. It was proved in the present study that employing the autoclave curing method of terminal boiling for the polymerization of 0.2% by weight of AgNp-added heat-activated PMMA denture base resulted in a significantly higher flexural strength compared to the conventional curing method of terminal boiling for polymerization. Unmodified heat-activated PMMA gave higher flexural strength values when polymerized by autoclave curing compared to the conventional curing method of terminal boiling.

RESUMEN

In recent years, novel technologies and techniques have allowed today the production of controlled architecture materials. Although autogenous bone graft substitutes remain the gold standard, enormous defects require supplementary alloplastic substitutes for reconstruction. Polymers have lately been explored for the same purpose and their biological performance has been under research since the last decade. The aim of this review is to analyse maxillofacial reconstruction with three-dimensional resin bone substitutes. A Problem Intervention Comparison Outcomes (PICO) analysis was done and a search was carried out in the Cochrane Database, PubMed, Google Scholar etc databases and a hand search was done to collect the related literature. All articles for maxillofacial reconstruction with three-dimensional resin bone substitutes were scrutinised. The manuscripts published from 1990 till May 2021, were included in this review. A total of 106 articles were obtained from a PICO-based keyword search, and 91 manuscripts were retrieved after excluding the duplicates. Out of these 57 manuscripts were excluded on the basis of title and abstract. From the remaining 34 studies, 17 were excluded after reading the full text based on the inclusion and exclusion criteria. During data extraction, four studies were removed and finally, 13 studies were included in this research. From this scoping review, we could conclude that polymethylmethacrylate and polylactic acid formulations are very promising resin bone substitutes for 3-dimensional reconstruction of maxillofacial defects. However, rigorous long-term clinical trials are needed to validate this conclusion.

RESUMEN

BACKGROUND: Different processing techniques are employed to obtain poly (methyl methacrylate) (PMMA) with consistent surface quality in terms of topography and tribological function. The purpose of this research is to evaluate its influence on the surface height distribution. METHODS: In this research, samples of conventional and CAD/CAM acrylic resins were prepared. The following surface roughness parameters were extracted from the profilometric readings: arithmetic mean roughness (Pa), skewness (Psk) and kurtosis (Pku). Profilometric profiles were additionally obtained. RESULTS: The average roughness (Pa) with the conventional technique was significantly higher compared to CAD/CAM (t = 4.595; P < 0.001). Heat-cured resins presented the highest mean Pa (F = 6.975; P = 0.06). Heat-cured and milled resins show lower coefficient variation (CV) values, indicating more consistent surface finishing. The surface profiles revealed distinct characteristics in terms of skewness and kurtosis. CONCLUSIONS: The surface processing method, chemical composition and resin type significantly influence the surface finishing of the resin. The CAD/CAM resins exhibited superior results in terms of surface arithmetic mean roughness (Pa). However, heat-cured resin revealed to present the better surface consistency.

Asunto(s)

RESUMEN

BACKGROUND: The ideal treatment for giant cell tumor of bone (GCTB) is still controversial. Various surgical adjuvants have been introduced following intralesional curettage to improve local control rates. However, findings from relevant studies are inconsistent, and no consensus has been reached. The purpose of this study is to determine what intraoperative adjuvant is effective in decreasing the recurrence of GCTB. METHODS: We performed a systematic review and meta-analysis of articles published in the PubMed and Embase electronic databases which assessed the recurrence rate of GCTB following intralesional curettage with or without various surgical adjuvants. Two authors independently evaluated all publications. Meta-analysis was performed with Stata/MP (Version 17.0, StataCorp LLC, TX, USA) and Review Manager (RevMan, Version 5.4.1, The Cochrane Collaboration, 2020). Pooled risk ratio (RR) was used for analysis, with P values less than 0.05 considered statistically significant. RESULTS: Twenty-four studies involving 2,579 patients were included in this analysis. The overall recurrence rates for patients treated with or without high-speed burring (HSB) are 11.9% (26/218) and 47.7% (92/193), respectively. The pooled RR for tumor recurrence is 0.33 (95% CI: 0.22 to 0.49, P<0.001). In the meanwhile, the overall recurrence rates for patients treated with or without chemical adjuvants are 23.5% (77/328) and 26.1% (73/280), respectively, with a pooled RR of 0.84 (95% CI: 0.63 to 1.10, P=0.89). Additionally, the overall recurrence rates for patients treated with or without polymethyl methacrylate (PMMA) are 20.4% (205/1,006) and 33.4% (314/939), respectively, with a pooled RR of 0.59 (95% CI: 0.50 to 0.69, P<0.001). CONCLUSIONS: Intraoperative application of HSB or PMMA has an additional antitumor effect, while the use of phenol or H2O2 fails to make any significant difference (PROSPERO: CRD42022344262).

Asunto(s)

RESUMEN

Objective: to present a 12-month follow-up with photographic and tomographic analyses of the effect of polymethyl methacrylate-based bone cement graft (PMMA) in gingival exposure (GE) in patients with excessive gingival display (EGD). Methods: Twelve patients with EGD were included. The PMMA was surgically placed. A frontal and lateral photograph protocol was performed at baseline (T0), 3 (T3), 6 (T6), and 12 months (T12) post-operatively. Soft tissue cone-beam computed tomography (ST-CBCT) was performed at T0 and T12. Measures included GE, length of the lip vermilion (LLV), lip shape (LS), nose width (NW), filter width (FW), nasolabial angle (NAS) while smiling, and nasolabial angle at rest (NAR). The height, thickness, and volume of the cement graft were also measured in the ST-CBCT. The comparisons were performed by Kruskal-Wallis test at 5 % of significance (p < 0.05). Results: The height, thickness, and volume of the PMMA were respectively 12.84 ± 1.59 mm, 3.83 ± 0.53, and 1532.02 ± 532.52 mm3. PMMA significantly decreased GE from 8.33 ± 1.25 mm (T0) to 6.60 ± 0.93 mm (T12) (p < 0.01). NAR was 98.34 ± 9.28° at T0 and increased to 105.13 ± 7.33° at T12; however, the angle value was not statistically different (p = 0.08). LLV, LS, NW, FW, and NAS did not exhibit statistical differences between the baseline and follow-up periods. Conclusions: PMMA significantly decreased GE in a 12-month follow-up without influencing adjacent soft tissue anatomical structures.

RESUMEN

Objectives: This study compares the bacterial susceptibility to three different provisional restorations manufactured with different laboratory techniques, i.e., heat cure, CAD/CAM, and 3D printing. Materials and Methods: Totally, 45 health patients with age group of 30-60 years undergoing complete veneer crown treatment were selected for the study and divided into three groups with 15 samples in each as Group I: the crowns were made from polymethyl methacrylate polymer fabricated by the conventional heat cure method, Group 2: the crowns were made from polymethyl methacrylate fabricated by subtractive manufacturing CAD/CAM method, and Group 3: the crowns were made from oligomers fabricated by additive manufacturing 3D printing. The samples were examined for bacterial adherence at scanning electron microscope. The colony-forming units (CFUs) were calculated, and statistically analyzed. Results: It has been determined that the digitally fabricated provisional restorations prove to be superior in terms of surface topography than to the conventionally fabricated provisional restorations. Conclusion: The study concludes that 3D-printed provisional restorations are more precise with reduced bacterial susceptibility than milled ones.

RESUMEN

INTRODUCTION: Surgical glove perforation has been linked to a double-fold increased risk of surgical site infection. Infection in the context of arthroplasty can have devastating consequences. In orthopaedics, use of polymethyl methacrylate (PMMA) bone cement is commonplace, and the impact on glove strength and perforation risk is not fully understood. This study aimed to examine the resistance to perforation and thickness of gloves following PMMA exposure, in accordance with the International Organization for Standardization (ISO) standard for glove integrity. METHODS: Pairs of gloves were separated and randomly sorted into exposure and control groups. Twenty pairs of latex and 40 pairs of polyisoprene gloves were used. Exposure group glove cuffs were in contact with cement from a single surface of the glove for 13 min as cement cured. Force to perforation and glove thickness were tested in accordance with ISO guidelines. RESULTS: Latex gloves were found to have a significantly increased force to perforation following PMMA exposure (10.26 Newtons (N) vs. 9.81 N, P = 0.048). Both polyisoprene under- and over-gloves were shown to have no significant change in strength to perforation post exposure (9.69 N vs. 9.83 N, P = 0.561, and 10.26 N vs. 10.65 N, P = 0.168, respectively). All groups were over the ISO standard minimum strength of 5 N. CONCLUSIONS: Exposure of latex and polyisoprene surgical gloves to PMMA bone cement does not appear to increase glove perforation risk and rather may improve natural rubber latex glove strength. This study supports the use of latex and polyisoprene surgical gloves in procedures that involve the handling of PMMA bone cement.

Asunto(s)