RESUMEN

Experimental light-curing pattern resins were fabricated to produce pattern resin materials with adequate dimensional stability. The light-curing pattern resins consisted of poly(n-butyl methacrylate) or poly(iso-butyl methacrylate) (PiBMA) polymers and methacrylate monomers. The physical properties, amount of residual ash after burning, Vickers hardness, flexural strength, and volumetric polymerization shrinkage of each material were determined. The data obtained for the prepared resins were compared with those of a commercially available pattern resin, Palavit G (PG). A lower amount of residual ash was observed for some of the prepared resins than for PG. The Vickers hardness and flexural strength values of all experimental resins were lower than those of PG. The volumetric polymerization shrinkage of all the experimental resins based on PiBMA was lower than that of PG. These results suggest that acrylic light-curing resin materials based on PiBMA may be useful for patterning and indexing during soldering.

Asunto(s)

RESUMEN

OBJECTIVE: Polymerization shrinkage poses a significant challenge in dental resin composites. The objective of this study is to introduce spiroorthocarbonate monomer 3,9-dimethylene-1,3,5,7-tetraoxa-spiro[5,5]undecane (BMSOC) and epoxy resin monomer 3,4-epoxycyclohexylmethyl-3,4-epoxycyclohexane carboxylate (ECHM-ECHC) into bisphenol-S-bis(3-methacrylato-2-hydroxy propyl)ether (BisS-GMA) based resin composites to develop composites with reduced shrinkage properties. METHODS: BMSOC and BisS-GMA were synthesized and thoroughly mixed with ECHM-ECHC, followed by inorganic fillers and photoinitiators. Based on the composition of the resin matrix, five groups of experimental composites were prepared, with traditional bisphenol A-dimethacrylate glycidyl ester (Bis-GMA)/triethylene glycol dimethacrylate (TEGDMA) based composite serving as the control. The polymerization properties, including degree of conversion (DC) and polymerization shrinkage (PS), as well as marginal microleakage, wettability, flexural strength (FS), flexural modulus (FM), and biocompatibility were evaluated. RESULTS: The results demonstrated that compared with the control group, the PS of BisS-GMA based composites containing BMSOC and ECHM-ECHC were significantly reduced (P < 0.05), and the lowest PS (0.96 ± 0.08 %) was observed when the ratio of BisS-GMA: (Epoxy + BMSOC) was 4:6. Additionally, the experimental composites also exhibited improved DC, minimal microleakage, low hydrophilicity, enhanced mechanical properties, qualified in vivo biocompatibility, and slight/moderate in vitro biocompatibility. SIGNIFICANCE: The resin composites incorporating multiple modified low-shrink monomers are promising for dental applications to prevent various clinical problems caused by PS and extend restoration longevity.

Asunto(s)

RESUMEN

OBJECTIVES: The purpose of this study was evaluating the performance of new Bis-EFMA based bulk-fill composites with common methacrylate based composites and commercial dental composites. METHODS: The Bis-EFMA monomer was synthesized and the novel Bis-EFMA based bulk-fill composites were prepared. The resin composite samples were co-cultured with human gingival epithelial cells and human dental pulp stem cells to test the biocompatibility. The edge adaptation was observed under a combination of stereoscope and scanning electron microscope. The internal hardness was measured using a Vickers microhardness tester after one-time filling of cavities prepared in extracted teeth. After friction and wear test on the surface of the resin composites, the surface morphology and volume wear of each group were measured by the optical profilometer. The color stability was measured by a colorimeter. RESULTS: Direct contact with human gingival epithelial cells and human dental pulp stem cells did not cause significant changes in their growth density and morphology, indicating good biocompatibility of Bis-EFMA group (p > 0.05). The continuous margin proportion of the Bis-EFMA group was as good as commercial bulk-fill composites (p > 0.05). The sectional microhardness results showed that the Bis-EFMA group had the highest microhardness. After the friction and wear test, the volume wear of the Bis-EFMA group was minimal, indicating its good wear resistance and mechanical strength. Color changes in all resin groups after 28 days of immersion were within the clinically acceptable range. SIGNIFICANCE: The addition of Bis-EFMA demonstrated excellent biocompatibility, edge adaptation and color stability comparable to commonly used clinical bulk-fill composites, along with preferable mechanical strength, friction and wear resistance. Bis-EFMA based bulk-fill composites have the potential to be employed as a bulk filling material in commercial dental composite applications.

Asunto(s)

RESUMEN

BACKGROUND: The purpose of this study was to investigate the effect of different light curing modes on the polymerization shrinkage of a bulk-fill composite and to evaluate the impact of two layering techniques on the cuspal deflection. METHODS: Nine different light curing modes were tested on bulk-fill composite samples in aluminum MOD cavities. Intensity, duration, and illumination distance were the factors that changed during the different curing modes. The digital image correlation method was used to visually represent the displacement of carbon particles on the materials' surface caused by shrinkage along both the horizontal and vertical axes. For simulating cuspal deflection, a separate protocol was used, with a bulk and horizontal layering technique. RESULTS: The results showed that the largest horizontal displacements were present in the soft start group (6.00 ± 0.82 µm) and in the X-tra power group (5.67 ± 1.21 µm). The smallest horizontal displacements were detected in normal curing modes (4.00 ± 1.58 µm; 4.00 ± 2.68 µm). The largest vertical displacements, at the bottom layer, were present in the normal curing mode group with a 20 s curing time (5.22 ± 1.56 µm), while the smallest vertical displacements were shown in the X-tra power group (2.89 ± 0.60 µm). The observed particle displacements showing the shrinkage of the composite were correlated with the curing mode. The bulk-fill group showed less cuspal deflection than the horizontal layering group did, but the difference was not statistically significant (p = 0.575). CONCLUSIONS: Within the limitations of this in vitro study, it can be concluded that lower intensities of curing lights (1200 mW/cm2) may perform better from the point of view of material shrinkage than high and extreme light intensities do. The pulse delay mode might be recommended in the case of bulk-fill materials. The number of layers did not significantly affect the cuspal deflection in the case of the studied composite.

RESUMEN

OBJECTIVE: To investigate the feasibility of optical coherence tomography (OCT)-based digital image correlation (DIC) analysis and to identify the experimental parameters for measurements of polymerization shrinkage. METHODS: Class I cavities were prepared on bovine incisors and filled with Filtek Z350XT Flowable (Z350F). One OCT image of the polymerized restoration was processed to generate virtually displaced images. In addition, the tooth specimen was physically moved under OCT scanning. A DIC software analyzed these virtual and physical transformation sets and assessed the effects of subset sizes on accuracy. The refractive index of unpolymerized and polymerized Z350F was measured via OCT images. Finally, different particles (70-80 µm glass beads, 150-212 µm glass beads, and 75-150 µm zirconia powder) were added to Z350F to inspect the analyzing quality. RESULTS: The analyses revealed a high correlation (>99.99%) for virtual movements within 131 pixels (639 µm) and low errors (<5.21%) within a 10-µm physical movement. A subset size of 51 × 51 pixels demonstrated the convergence of correlation coefficients and calculation time. The refractive index of Z350F did not change significantly after polymerization. Adding glass beads or zirconia particles caused light reflection or shielding in OCT images, whereas blank Z350F produced the best DIC analysis results. SIGNIFICANCE: The OCT-based DIC analysis with the experimental conditions is feasible in measuring polymerization shrinkage of RBC restorations. The subset size in the DIC analysis should be identified to optimize the analysis conditions and results. Uses of hyper- or hypo-reflective particles is not recommended in this method.

Asunto(s)

RESUMEN

OBJECTIVES: To examine the polymerization shrinkage of different resin-based composite (RBC) restorations using optical coherence tomography (OCT) image-based digital image correlation (DIC) analysis. METHODS: The refractive index (RI) of three RBCs, Filtek Z350XT (Z350), Z350Flowable (Z350F), and BulkFill Posterior (Bulkfill), was measured before and after polymerization to calibrate their axial dimensions under OCT. Class I cavities were prepared in bovine incisors and individually filled with these RBCs under nonbonded and bonded conditions. A series of OCT images of these restorations were captured during 20-s light polymerization and then input into DIC software to analyze their shrinkage behaviors. The interfacial adaptation was also examined using these OCT images. RESULTS: The RI of the three composites ranged from 1.52 to 1.53, and photopolymerization caused neglectable increases in the RI values. For nonbonded restorations, Z350F showed maximal vertical displacements on the top surfaces (-16.75 µm), followed by Bulkfill (-8.81 µm) and Z350 (-5.97 µm). In their bonded conditions, all showed increased displacements. High variations were observed in displacement measurements on the bottom surfaces. In the temporal analysis, the shrinkage of nonbonded Z350F and Bulkfill decelerated after 6-10 s. However, Z350 showed a rebounding upward displacement after 8.2 s. Significant interfacial gaps were found in nonbonded Z350 and Z350F restorations. SIGNIFICANCE: The novel OCT image-based DIC analysis provided a comprehensive examination of the shrinkage behaviors and debonding of the composite restorations throughout the polymerization process. The flowable composite showed the highest shrinkage displacements. Changes in the shrinkage direction may occur in nonbonded conventional composite restorations.

Asunto(s)

RESUMEN

OBJECTIVES: This study utilized non-linear finite element (FE) models to explore polymerization shrinkage and its impact on marginal integrity in molars following both selective caries removal (SCR) and conventional treatment. Specifically, we performed 2D in silico simulations to study residual stresses post-resin polymerization shrinkage and their influence on the marginal integrity of various restoration types. METHODS: Initially, FE models were developed based on a cohesive zone framework to simulate crack propagation along the bonded interfaces between restoration and tooth structure in SCR-treated molars with class I and class II restorations. The modeled resin composite restorations first underwent polymerization shrinkage and were then subjected to various occlusal loading conditions. Stress magnitudes and distributions were identified to evaluate the margin integrity and predict the mechanism and location of interfacial failure. RESULTS AND DISCUSSION: The FE models computed polymerization shrinkage stresses of less than 1 MPa, exerting a minor influence on the composite/tooth interface. Occlusal loading, however, significantly impacted the load-bearing capacity of the composite/tooth (c/t) interface, potentially jeopardizing the restoration integrity. Especially under bi-axial occlusal loading, interfacial debonding occurred in the vertical cavity walls of the class I restorations, increasing the risk of failure. Notably, SCR-treated teeth exhibited better margin integrity than restored teeth after complete caries removal (NCR). These findings provide valuable insights into the mechanical behavior of SCR-treated teeth under different loading conditions and highlight the importance of considering the load scenarios that may lead to failure at the c/t interface. By investigating the factors influencing crack initiation and delamination, this novel research contributes to the optimization of restorative treatments and aids in the design of more resilient dental restorations.

Asunto(s)

RESUMEN

OBJECTIVES: The study aimed to introduce a novel two-step optical fiber-based photo-activation of dental resin-based composites (RBCs) for reducing polymerization shrinkage stress (PSS). METHODS: Proposed protocol design - in the first step, two flexible plastic optical fibers connected to a dental light curing unit (LCU), were used as light guides inserted into the filling to initiate low-irradiance polymerization from within; in the second step, fibers were extracted and remaining voids were filled with RBC, followed by conventional high-irradiance curing to finalize polymerization. Three bulk-fill RBCs were tested (Beautifil-Bulk Restorative, Filtek Bulk-fill Posterior, Tetric PowerFill) using tooth cavity models. Three non-invasive examination techniques were employed: Digital Holographic Interferometry, Infrared Thermography, and Raman spectroscopy for monitoring model deformation, RBC temperature change, and degree of conversion (DC), respectively. A control group (for each examined RBC) underwent conventional photo-activation. RESULTS: The experimental protocol significantly reduced model deformation by 15 - 35 %, accompanied by an 18 - 54 % reduction in RBC temperature change, emphasizing the impact of thermal shrinkage on PSS. Real-time measurements of deformation and temperature provided indirect insights into reaction dynamics and illuminated potential mechanisms underlying PSS reduction. After a 24-hour dark-storage period, DC outcomes comparable to conventional curing were observed, affirming the clinical applicability of the method. CONCLUSIONS: Protocol involving the use of two 1.5 mm fibers in the first step (300 mW/cm2 x 10 s), followed by a second conventional curing step (1000 mW/cm2 x 10 s), is recommended to achieve the desired PSS reduction, while maintaining adequate DC and ensuring efficient clinical application. CLINICAL SIGNIFICANCE: Obtained PSS reduction offers promise in potentially improving the performance of composite restorations. Additionally, leveraging the flexibility of optical fibers improves light guide approach for restorations on posterior teeth. Meanwhile, implementation in clinical practice is easily achievable by coupling the fibers with commercial dental LCUs using the provided plastic adapter.

Asunto(s)

RESUMEN

Background and objective Resin-based restorative materials are the backbone of modern restorative dentistry. But in spite of being an excellent material, there are many shortcomings with direct resin restorative materials such as polymerization shrinkage and microleakage that complicate the rate of clinical success. Hence, the aim of the present study is to compare the microleakage caused by composite restorations using two different bevels, primary and zigzag bevels, while restoring fractured anterior teeth. Materials and methodology Thirty non-carious maxillary central incisors were split into two divisions wherein Group I received the primary bevel and Group II received the zigzag bevel. After receiving the bevel, the samples are restored with direct filling composite material (Neo Spectra ST, Dentsply Sirona, Charlotte, NC, USA). The restored samples underwent thermocycling (Holmarc, Kochi, India) and were assessed for microleakage under a stereomicroscope (Leica M205, Wetzlar, Germany). For the statistical analysis, IBM SPSS Statistics for Windows, V. 23.0 (IBM Corp., Armonk, NY) was used. Descriptive statistics were expressed in mean and standard deviation. Analytical statistics including the independent Student t-test was used to assess the difference derived from both groups at p<0.05. The normality of the data was assessed using the Shapiro-Wilk test. Results In the primary bevel, 53.3% of the samples showed first-degree microleakage, and 46.7% showed second-degree microleakage, respectively, and in samples restored using the zigzag bevel, 66.7% of the samples had no microleakage, and 33.3% of the samples had first-degree microleakage. The independent t-test revealed that the microleakage of the zigzag bevel showed a significant difference, being superior to the primary bevel at p<0.01. Conclusion Acknowledging the limitations of the study conducted, both bevel designs had a certain degree of microleakage when restored with composite material in anterior fractured teeth. However, the zigzag bevel produced significantly lesser microleakage as compared to the primary bevel restorations.

RESUMEN

OBJECTIVE: The current dental resin composites often suffer from polymerization shrinkage, which can lead to microleakage and potentially result in recurring tooth decay. This study presents the synthesis of a novel monomer, (3,9-diethyl-1,5,7,11-tetraoxaspiro[5,5]undecane-3,9-diyl)bis(methylene) bis((2-(3-(prop-1-en-2-yl)phenyl)propan-2-yl)carbamate) (DDTU-IDI), and evaluates its effect in the formulation of low-shrinkage dental resin composites. METHODS: DDTU-IDI was synthesized through a two-step reaction route, with the initial synthesis of the required raw material monomer 3,9-diethyl-3,9-dihydroxymethyl-1,5,7,11-tetraoxaspiro-[5,5] undecane (DDTU). The structures were confirmed using Fourier-transform infrared (FT-IR) spectroscopy and hydrogen nuclear magnetic resonance (1HNMR) spectroscopy. Subsequently, DDTU-IDI was incorporated into Bis-GMA-based composites at varying weight percentages (5, 10, 15, and 20 wt%). The polymerization reaction, degree of conversion, polymerization shrinkage, mechanical properties, physicochemical properties and biocompatibility of the low-shrinkage composites were thoroughly evaluated. Furthermore, the mechanical properties were assessed after a thermal cycling test with 10,000 cycles to determine the stability. RESULTS: The addition of DDTU-IDI at 10, 15, and 20 wt% significantly reduced the polymerization volumetric shrinkage of the experimental resin composites, without compromising the degree of conversion, mechanical and physicochemical properties. Remarkably, at a monomer content of 20 wt%, the polymerization shrinkage was reduced to 1.83 ± 0.53%. Composites containing 10, 15, and 20 wt% DDTU-IDI exhibited lower water sorption and higher contact angle. Following thermal cycling, the composites exhibited no significant decrease in mechanical properties, except for the flexural properties. SIGNIFICANCE: DDTU-IDI has favorable potential as a component which could produce volume expansion and increase rigidity in the development of low-shrinkage dental resin composites. The development of low-shrinkage composites containing DDTU-IDI appears to be a promising strategy for reducing polymerization shrinkage, thereby potentially enhancing the longevity of dental restorations.

Asunto(s)

RESUMEN

Photopolymerization kinetics affects the curing time, degree of conversion, polymerization shrinkage, and mechanical properties of composites. The aim of this study was to compare three methods (temperature, heat flow, and polymerization shrinkage) for photopolymerization kinetics measurement of composites. The photopolymerization kinetics of four composites (2 packable and 2 flowable) were measured with an LED light for 20 s (radiant emittance: 2,100 mW/cm2). For the two packable composites, photopolymerization kinetics was measured with varying the radiant emittance and exposure time. For each measurement method, peak times were determined as the time when maximum temperature rise, heat flow, and shrinkage rate occurred, respectively. The photopolymerization kinetics differed among the measurement methods. The photopolymerization kinetics of composites changed as the radiant emittance and composite type varied. In clinical practice and research on the composite restoration, the kinetics should be considered comprehensively with the complementary use of various measurement methods.

Asunto(s)

RESUMEN

Polymerization shrinkage is a major side effect of resin composite materials that affects the success and longevity of caries restorations. This study was to analyze the effect of the internal angle and shape of the lining on the shrinkage residual stress of dental restorations in Class II mesio-occlusal-distal (MOD) cavities through finite element analysis (FEA). A 3D reconstructed model of a human mandibular first molar was created from micro-CT images, and then the tooth was prepared as a Class II MOD cavity. 3D models of four regular internal corner shapes of Class II MOD cavities with different internal angles of lining and one 90° filleted corner model were created. The thermal expansion technique was applied to approximate the shrinkage impact of composite resin polymerization in the FE software ABAQUS. Von Mises stress was taken as a metric. The results showed that the level of residual stresses in the Class II MOD cavities was greatly dependent on the internal angle of the lining. The maximum von Mises stress in tooth tissue decreased as the internal angle of the lining increased. The internal shapes of the lining had no obvious effect on the stress, and the filleted corner model had less stress. This lining strategy is appropriate for Class II MOD cavities with serious loss of tooth tissue.

Asunto(s)

RESUMEN

BACKGROUND:At present,the dental composite resin filling material composed of resin matrix monomer is the first choice material for the filling treatment of dental defects,but with the increase of its use time in the oral environment,the dental tissue will develop secondary caries and the filling material will wear and break.The main cause of these problems is the polymerization shrinkage of the filling material and its mismatch with the mechanical properties of the dental tissue. OBJECTIVE:To synthesize a new type of dental composite resin monomer by adding initiators with different components,to improve the traditional double bond conversion rate of the system and further improve the mechanical properties of the material. METHODS:A new composite resin matrix system was prepared by adding different initiators to the monomer of 3,3′,5,5′-tetramethoxybiphenyl-4,4′-diol epoxy acrylate resin.In group A,camphorquinone with a mass fraction of 1.1%was added.In group B,1-phenyl-1,2-propanedione with a mass fraction of 2.1%was added.In group C,a mixture of camphorquinone and 1-phenyl-1,2-propanedione(a mass ratio of the two was 1:1)with a mass fraction of 3.1%was added.The double bond conversion,polymerization shrinkage and mechanical properties of the samples were determined. RESULTS AND CONCLUSION:(1)The double bond conversion rate of groups B and C was higher than that of group A(P<0.05).The polymerization shrinkage of group B was higher than that of group A(P<0.05),while that of group C was lower than that of group A(P<0.05).(2)The flexural strength,elastic modulus and compressive strength of groups B and C were higher than those of group A(P<0.05,P<0.01).Vickers hardness of group B was higher than that of group A(P<0.05),and the Vickers hardness of group C was lower than that of group A(P<0.01).(3)These findings suggest that 1-phenyl-1,2-propanedione is an initiator with ideal performance.The combined application of 1-phenyl-1,2-propanedione and camphorquinone can effectively improve the double bond conversion rate of the resin matrix system and further improve the mechanical property of the resin.

RESUMEN

PURPOSE: The first objective was to determine if dual-curing of resin cement with reduced light could affect interfacial adaptations of zirconia restoration. The second objective was to examine whether cement type and pretreatment method of universal adhesive affected interfacial adaptation. The final objective was to compare the polymerization degree of cement under different reduced-light conditions. MATERIALS AND METHODS: Inlay cavities were prepared on extracted third molars. Translucent zirconia restorations were milled using Katana UTML (Kuraray Noritake) in three groups with restoration thicknesses of 1, 2, and 3 mm, respectively. Each group had three subgroups using different cementation methods. For subgroup 1, restorations were cemented with self-adhesive cement. For subgroup 2, universal adhesive was applied and light cured. After the restoration was seated with conventional resin cement, light curing was performed. For subgroup 3, after adhesive was applied, the restoration was seated with conventional resin cement. Light curing was performed for the adhesive and cement simultaneously. After thermocycling, interfacial adaptation at the restoration-tooth interface was investigated using swept-source optical coherence tomography imaging. Finally, polymerization shrinkage of the cement was measured using a linometer and compared under the conditions of different zirconia thicknesses and light-curing durations. RESULTS: Interfacial adaptation varied signficantly depending on the zirconia thickness, pretreatment, polymerization mode and cements used (p < 0.05). The effects of the adhesive and polymerization shrinkage differed signficantly, depending on the reduced light under the zirconia (p < 0.05). CONCLUSION: Lower curing-light irradiance may lead to inferior adaptation and lower polymerization of the cement. Polymerization of resin cement can differ depending on the light irradiance and exposure duration.

Asunto(s)

RESUMEN

Dental resin restorations commonly fail because of fractures and secondary caries. The aim of this research was to synthesize a novel low-shrinkage dental resin with antibacterial and self-healing properties. The low-shrinkage dental resin was obtained by incorporating a 20 wt% anti-shrinkage mixture of an expanding monomer 3,9-diethyl-3,9-dimethylol -1,5,7,11-tetraoxaspiro[5,5] undecane and an epoxy resin monomer diallyl bisphenol A diglycidyl ether (1:1, referred as "UE") and different mass fractions of self-healing antibacterial microcapsules (0%, 2.5%, 5%, 7.5%, and 10%) were incorporated into the matrix to prepare multifunctional dental resin. Polymerization shrinkage, mechanical properties, antibacterial activity, self-healing ability, and cytotoxicity of this dental resin were evaluated. The polymerization volumetric shrinkage of resin containing 20 wt% UE and 7.5 wt% microcapsules was reduced by 30.12% (4.13% ± 0.42%) compared with control. Furthermore, it exhibited high antibacterial activity and a good self-healing efficiency of 71% without adversely affecting the mechanical property and cell viability. This novel multifunctional dental resin with low polymerization shrinkage and excellent antibacterial activity and self-healing capability has potential application as a dental resin material to decrease the incidence of fractures and secondary caries.

Asunto(s)

RESUMEN

OBJECTIVE: The configuration factor (C-factor) is an index used to evaluate the relationship between cavity configuration and the development of polymerization shrinkage stress in dental restorations. Although C-factor has been widely researched, its correlation with stress analysis in dental restorations remains controversial. This review aims to discuss the application and limitations of C-factor and define the restricted conditions under which the C-factor "rule of thumb" is applicable. METHODS: A thorough literature review was conducted on the application and limitations of C-factor in stress analysis of dental restorations. This was principally based on MEDLINE/PubMed and Web of Science databases and a review of the relevant studies and publications in scientific papers in international peer-reviewed journals for the specific topic of C-factor and polymerization shrinkage. RESULTS: The C-factor alone cannot provide an accurate prediction of the shrinkage stress of restorations and the mechanical behavior of material-tooth interfaces. C-factor is only applicable under one condition not typically seen in clinical practice: low, near-rigid compliance. SIGNIFICANCE: Conditions for the application of C-factor have been explicitly defined. A more accurate and precise understanding and utilization of the C-factor is of benefit as it contributes to better understanding of polymerization shrinkage behavior of restorations.

Asunto(s)

RESUMEN

The study aimed to compare shrinkage displacements of fully and partially bonded resin composite restorations (RCRs). Two groups (n=5) Class-I RCR evaluated: Group 1 (G1) fully bonded and Group 2 (G2) debonded at the floor. Experimental results were compared with predictions from simple theory and finite element analysis (FEA). The experimental linear surface displacement (LSD) was G1 62.5±5.2 µm and G2 32.8±4.0 µm. Theoretically-predicted LSD for G1 60.1±7.4 µm and G2 31.3±7.5 µm. FEA-predicted LSD were G1 65.2 µm and G2 34.6 µm. The experimental volumetric surface displacement (VSD) was G1 1.22±0.2 mm3 and G2 0.63±0.2 mm3. Theoretically-predicted VSD for G1 1.36±0.2 mm3 and G2 0.67±0.2 mm3. No significant difference (p>0.05) was found in LSD and VSD among the experimental, theoretical and FEA in the same group. Significant differences (p<0.05) were noted between the two groups, with LSD and VSD of G2 values being almost half of G1. This pattern gave an insight of a debond restoration characteristics.

RESUMEN

This study evaluated the interfacial integrity of deep (6 mm) Class-II (OM/OD) restorations placed using different bulk-fill resin composites [Filtek™ Bulk Fill Flowable Restorative (BF) and Filtek™ Bulk Fill Posterior Restorative (BP) (3M ESPE, St. Paul, MN, USA)] of different increment thicknesses (2 or 4 mm). BP was used for capping in all cases, while Filtek™ Z250 Universal Restorative (3M ESPE) was used as the control material. Interfacial debonding was measured during curing through acoustic emission (AE), followed by image analysis using micro-computed tomography and scanning electron microscopy. Microhardness testing was also conducted to assess degree of conversion. Depth of cure was adequate in all restorations. Specimens with 4-mm thick first increment of BF, which had a higher shrinkage strain, produced most AE events and debonding. Thus, bulk filling of deep cavities using bulk-fill resin composites with a high shrinkage strain should be avoided.

RESUMEN

OBJECTIVES: The current study aimed to investigate the bonding properties of a novel low-shrinkage resin adhesive containing expanding monomer and epoxy resin monomer after thermal cycling aging treatment. METHODS: Expanding monomer of 3,9-diethyl-3,9-dimethylol-1,5,7,11-tetraoxaspiro-[5,5] undecane (DDTU) as an anti-shrinkage additive and unsaturated epoxy monomer of diallyl bisphenol A diglycidyl ether (DBDE) as a coupling agent were synthesized. A blend of DDTU and DBDE at a mass ratio of 1∶1, referred to as "UE", was added into the resin matrix at the mass fraction of 20% to prepare a novel low-shrinkage resin adhesive.Then, the methacrylate resin adhesive without UE was used as the blank control group, and a commercial resin adhesive system was selected as the commercial control group. Moreover, the resin-dentin bonding and micro-leakage testing specimens were prepared for the thermal cycling aging treatment. The bonding strength was tested, the fracture modes were calculated, the bonding fracture surface was observed by scanning electron microscope (SEM), and the dye penetration was used to evaluate the tooth-restoration marginal interface micro-leakage. All the data were analyzed statistically. RESULTS: After aging, the dentin bonding strength of the experimental group was (19.20±1.03) MPa without a significant decrease (P>0.05), that of the blank control group was (11.22±1.48) MPa with a significant decrease (P<0.05) and that of the commercial control group was (19.16±1.68) MPa without a significant decrease (P>0.05). The interface fracture was observed as the main fracture mode in each group after thermal cycling by SEM. The fractured bonding surfaces of the experimental group often occurred on the top of the hybrid layer, whereas those of the blank and commercial control groups mostly occurred on the bottom of the hybrid layer. Micro-leakage rating counts of specimens before and after thermal cycling were as follows: the experimental group was primarily 0 grade, thereby indicating that a relatively ideal marginal sealing effect could be achieved (P>0.05); meanwhile, the blank control group was primarily 1 grade, and the penetration depth of dye significantly increased after thermal cycling (P<0.05); the commercial control group was primarily 0 grade without statistical difference before and after thermal cycling (P>0.05), while a significant difference was observed between the commercial control group and experimental group after thermal cycling (P<0.05). CONCLUSIONS: The novel low-shrinkage resin adhesive containing 20%UE exhibited excellent bonding properties even after thermal cycling aging treatment, thereby showing a promising prospect for dental application.

Asunto(s)

RESUMEN

Flowable bulk-fill resin-based composites (BF-RBCs) represent a new and interesting alternative for the bulk-fill restorative techniques in the posterior region. However, they comprise a heterogeneous group of materials, with important differences in composition and design. Therefore, the aim of the present systematic review was to compare the main properties of flowable BF-RBCs, including their composition, degree of monomer conversion (DC), polymerization shrinkage and shrinkage stress, as well as flexural strength. The search was conducted following PRISMA guidelines in the Medline (PubMed), Scopus and Web of Science databases. In vitro articles reporting on the DC, polymerization shrinkage/shrinkage stress, and flexural strength of flowable BF-RBCs strength were included. The QUIN risk-of-bias (RoB) tool was used for assessing the study quality. From initially 684 found articles, 53 were included. Values for DC ranged between 19.41 and 93.71%, whereas polymerization shrinkage varied between 1.26 and 10.45%. Polymerization shrinkage stresses reported by most studies ranged between 2 and 3 MPa. Flexural strength was above 80 MPa for most materials. A moderate RoB was observed in most studies. Flowable BF-RBCs meet the requirements to be indicated for bulk fill restoration technique in the posterior region. However, important variations among composition and properties hinder extrapolation of the results to materials different from those reported here. Clinical studies are urgently required to assess their performance under a real working scenario.