RESUMEN

OBJECTIVE: This study evaluated the clinical performance of Class II restorations made with flowable bulk-fill base versus conventional layering ORMOCER-based restorative material in a split-mouth randomized clinical trial. METHODS: Thirty patients received two class II restorations (n = 60) performed with different strategies. All preparations received the application of the universal self-etching adhesive system according to the manufacturer's recommendation, followed by the placement of a sectional matrix, wooden wedge, and separation ring. The first restoration was performed using 4 mm of flowable bulk-fill material covered by 2 mm of conventional viscosity restorative material (Bulk-fill technique). The second restoration was performed only with the conventional viscosity material, with a maximum of 2 mm thick increments, up to fill the cavity (Layering technique). After occlusal adjustment, the same polishing system was used for all restorations. Evaluations using the FDI criteria were conducted after 7 days, 12, and 24 months. Data were analyzed with the Fisher's Exact test (α=0.05). RESULTS: From 30 participants, 24 attended the 24-month recall, and 48 restorations were evaluated. All restorations received acceptable overall scores for esthetic and biological properties after this period, while only 6.66 % of the restorations exhibited unacceptable overall scores for the functional properties in both groups. No significant differences between the tested restorative materials and techniques were found for each FDI criterion assessed. The success rate after 2 years was 93.33 % for both groups. CONCLUSION: Both restorative materials exhibited good clinical performance for the parameters analyzed with no differences between them after 24-month follow-up. CLINICAL RELEVANCE: Flowable bulk-fill ORMOCER-based material is a suitable alternative for direct Class II restorations, providing good clinical outcomes and simplifying the restorative procedure. CLINICAL TRIAL REGISTRATION NUMBER: RBR-6mvp9w.

Asunto(s)

RESUMEN

OBJECTIVE: to compare conventional nanohybrid (Ceram.x Spectra) and ormocer-based (Admira fusion) dental composite resins effects on human dental pulp stem cells (hDPSCs) in terms of cytotoxicity, self-renewal, migration and osteogenic differentiation. METHODS: hDPSCs were cultured in presence of different dilutions (undiluted, form 1:2 to 1:100) of CeramX (CX) and Admira fusion (AD) eluates and viability assay in standard or osteogenic conditions were performed. Samples and eluates were prepared according to ISO 10993-12. In addition, apoptosis, self-renewal and migration activity evaluations were carried out. Osteogenic differentiation potential was tested by Alkaline Phosphatase Activity, alizarin red staining and gene expression of specific markers (ALP, RUNX2, OCN, OPN and COL1α1). Statistical analysis was performed by means of a One-way analysis of variance (One-way ANOVA) followed by a Tukey's test for multiple comparison; results were presented as mean ± standard error of mean (SEM). RESULTS: Admira Fusion demonstrated to be highly biocompatible and showed positive effects on hDPSCs proliferation and differentiation; on the contrary, conventional nanohybrid composite showed to be more cytotoxic and without any notable effect on stem cells differentiation. Moreover, the obtained results were further corroborated by a significant upregulation of osteogenic differentiation markers obtained in presence of ormocer-based composite resin eluate. Specifically, in AD 1:50 group expression levels of ALP, Runx2, Col1α1 were double than control (ALP, p = 0.045; Runx2, p = 0.003; Col1α1, p = 0.001) and CX 1:50 (ALP, p = 0.006; RUNX2, p = 0.029; Col1α1, p = 0.005). Moreover, in the same group, OPN and OCN resulted about 5 times more expressed as compared to control (OPN, p = 0.009; OCN, p = 0.0005) and CX 1:50 (OPN, p = 0.012; OCN, p = 0.0006). SIGNIFICANCE: The less cytotoxicity obtained by AD than conventional nanohybrid composite may be attributed to a reduced monomers release in the oral environment, supporting the hypothesis of limited adverse effect and enhanced healing potential, mainly when the material is positioned in close contact with pulp tissue.

Asunto(s)

RESUMEN

BACKGROUND: The study aimed to evaluate the influence of various beverages; with and without brushing; on the surface mechanical properties of two resin composites. METHODS: A total of 160 disc-shaped specimens were prepared for each of the following dental composites; nanohybrid ormocer (Admira fusion, VOCO GmbH, Cuxhaven, Germany) and nanohybrid resin composite (Grandio, VOCO GmbH, Cuxhaven, Germany). The baseline surface hardness and roughness measurements were carried out after 24 h. The composite samples were randomly distributed into one of the two groups; brushing and non-brushing, which were further divided into one of the four subgroups (n = 10); artificial saliva as control, coffee, red wine, and soft drink. In the non-brushing group, the specimens were immersed in the different beverages for five minutes three times daily for 30 days. The same procedure was done for the brushing group, in addition to brushing the specimens for five seconds. The surface hardness and roughness measurements were repeated after 30 days. One-way ANOVA and independent t-tests were used for statistical analysis. RESULTS: The soft drink had the most deteriorating effect and artificial saliva had the least. The change in surface properties was higher in the brushing subgroups. Grandio exhibited a higher change in surface microhardness while Admira fusion exhibited a higher change in surface roughness. CONCLUSIONS: The surface properties of both dental resin composites were negatively affected by using beverages and brushing.

Asunto(s)

RESUMEN

Aim: To evaluate the staining effect of different children's health drinks (Boost, Complan, and Pediasure) on esthetic restorative materials (giomer, nanohybrid composite, and ormocer). Materials and methods: The specimens consist of giomer, nanohybrid composite, and ormocer. Before the discoloration process, 80 disks of each material were fabricated, each measuring 5 mm in diameter and 2 mm in thickness. These disks were then measured for lightness*red/green*blue/yellow (L*a*b*) values. Around 10 samples from each subgroup were then submerged in each of the four staining solutions. Analysis of discoloration levels was done at baseline and 48 hours after immersion in the staining solution. Each specimen's staining effect was evaluated using a spectrophotometer.Each specimen's L*a*b* values were measured three times by placing it on the measurement head. The internal energy (ΔE) unit, which expresses resistance to the staining effect, was derived using each specimen's L*a*b* values. Results: All the tested materials showed a color change. However, giomer showed greater ΔE values compared to nanohybrid composite and ormocer. Of all the immersion media used, Boost samples resulted in the highest color change, followed by Complan, Pediasure, and milk. Conclusion: Out of the three restorative materials used in the study, ormocer showed more resistance to color change than nanohybrid composite and giomer with all the tested media. How to cite this article: Ponnala SL, Punithavathy R, Birapu UKC, et al. An In Vitro Staining Effect of Different Children's Health Drinks on Esthetic Restorative Materials. Int J Clin Pediatr Dent 2023;16(2):211-217.

RESUMEN

Shell nacre from Pinctada species has been extensively researched for managing bone defects. However, there is a gap in the research regarding using shell nacre powder as a cement with improved biological and physicochemical properties. To address this, bone void filling cement was formulated by incorporating shell nacre powder and an organically modified ceramic resin (ormocer). The shell nacre powder was specifically processed from the shells of Pinctada fucata and analysed using thermogravimetric analysis (TGA), X-ray diffraction spectroscopy, Fourier transform infrared (FTIR), and Raman spectroscopy, confirming the presence of organic constituents and inorganic aragonite. Trace element analysis confirmed the eligibility of shell nacre powder for biomedical applications. Next, the ormocer SNLSM2 was synthesized through a modified sol-gel method. FTIR, Raman, TGA, and transmission electron microscopy studies revealed the presence of a ladder-structured siloxane backbone and methacrylate side chain. To develop chemical curable composite shell nacre cement (SNC), different amounts of shell nacre (24%, 48%, and 72%) were added to the SNLSM2 resin, and the impact on the physicochemical properties of the cement was studied. Among the compositions, SNC 72 exhibited significantly lower linear polymerization shrinkage (0.4%) and higher compressive (>100 MPa) and flexural strength (>35 MPa). SNC 72 was radiopaque, and the exotherm generated during the cement curing was minimal. Cytotoxicity studies with L929 cells revealed the non-cytotoxic nature of the cement. Overall, the findings of this study prove that the shell nacre cement is a promising candidate for managing bone voids.

RESUMEN

This in vitro study aimed to compare the microleakage and marginal integrity of methacrylate/ormocer-based bulk-fill composite (BFC) restorations used in cervical marginal relocation with two different layering thicknesses in mesio-occlusal-distal (MOD) cavities exposed to thermo-mechanical loading. Standard MOD cavities were prepared in 60 mandibular molars and assigned into three groups: x-tra fil/AF + x-tra base/XB, Tetric N-Ceram Bulk Fill/TNB + Tetric N-Flow Bulk Fill/TFB, and Admira Fusion x-tra/AFX + Admira Fusion x-base/AFB. Each group was further divided into two subgroups (2 mm and 4 mm) based on the thickness of flowable BFCs (n = 10). The specimens were subjected to thermo-mechanical loading (240,000 cycles) and immersed in 0.2% methylene blue. Following mesiodistal sectioning, the specimens were examined under stereomicroscope (×25) and scored (0-3) for microleakage. Marginal integrity was examined using a scanning electron microscope (SEM). Descriptive statistical methods and the chi-square test were used to evaluate the data (p < 0.05). While there was no statistically significant difference in gingival cement microleakage in the XB and AFB specimens with a 4 mm thickness, microleakage was significantly increased in the TFB specimen (p = 0.604, 0.481, 0.018 respectively). A significantly higher amount of score 0 coronal microleakage was detected in the AFX2 mm + AFB4 mm compared to the TNB2 mm + TFB4 mm (p = 0.039). The SEM examination demonstrated better marginal integrity in groups with 2 mm thick flowable BFCs. Ormocer and methacrylate-based materials can be used in marginal relocation with thin layers.

RESUMEN

BACKGROUND: The pre-cure temperature is considered an important parameter that affects the polymerization kinetics and the properties of composite restoration. As dissension exists about the effect of storing composite restorative materials in refrigerator, this study aimed to assess the effect of shelf-storage temperature on degree of conversion (DC) and microhardness of three composite restorative materials with different matrix systems. METHODS: Three commercially-available composite restorative materials were used in this study; an Ormocer-based composite (Admira Fusion, Voco GmbH), a nanoceramic composite, (Ceram.X SphereTEC One, Dentsply Sirona GmbH), and a nanohybrid composite (Tetric N-Ceram, Ivoclar Vivadent AG). Regarding DC and microhardness tests, 60 disc-shaped composite specimens for each test were randomly divided into 3 groups (n = 20) according to the restorative material used. Each group was divided into 2 subgroups (n = 10) according to the composite storage temperature; stored at room temperature or stored in the refrigerator at 4°-5 °C. DC was evaluated using a Fourier-transform infrared spectrometer coupled to an attenuated total reflectance accessory. Microhardness was evaluated using micro-Vickers hardness tester under a load of 50 g with a dwell time of 10 s. The results were analyzed by ANOVA, post-hoc LSD, and independent t-tests at a significance level of p < 0.05. RESULTS: Regarding DC test all groups showed statistically significant differences at both storage temperature. The Ormocer-based composite had the highest mean values. There was a statistically significant difference between all room-stored groups and their corresponding groups stored at refrigerator (p < 0.05). For microhardness test, all groups exhibited also statistically significant differences at both storage temperatures with the Ormocer-based composite having the highest mean values. A statistically significant difference between both room-stored and refrigerator-stored groups has been observed also (p < 0.05). CONCLUSIONS: Refrigeration of resin-composite might have a deleterious effect on DC and microhardness of the tested composite restorative materials with different matrix systems. Moreover, the differences in the formulations of composite matrix have a potential impact on DC and microhardness.

Asunto(s)

RESUMEN

Single-shade universal resin composites (SsURC) are preferred in clinical practice to reduce time for shade selection and obtain good esthetic results. In this study, the static mechanical properties of seven new SsURCs were investigated, their spectral analyzes were performed and scanning electron microscopy (SEM) evaluations were presented. Charisma Diamond One/DO, Admira Fusion x-tra/AFX, Omnichroma/OC, OptiShade/OS, Essentia Universal/EU, Zenchroma/ZC, Vittra APS Unique/VU were used in a three-point bending test to determine flexural strength (FS) and elastic modulus (EM); Vickers micro-hardness (VHN) and hardness-ratio (HR) were performed with a micro-hardness tester from top/bottom after 24-h/15-days of storage in distilled water at 37 °C (±1 °C). The degree of conversion (DC) was assessed by using Fourier transform infrared spectroscopy (FTIR). The structure of the resin matrix and filler content were assessed by SEM. Data were analyzed using IBM SPSS V23 and the R program and the significance level was taken as p < 0.05. The main effect of the tested SsURCs was found to be statistically significant on FS, EM, VHN, and DC values (p < 0.001). Bis-GMA free SsURCs (AFX, DO, VU) showed better DC and HR except for OC. All seven tested SsURCs conform to the requirements of ISO standards for dental resin composites for all tested categories.

RESUMEN

Aims: This study aimed to evaluate the effect of preheated nanoceramic resin-based composite (RBC) (Ceram-X-Mono) placed in Class I occlusal cavities over a period of 18 months. Settings and Design: This study involves split-mouth design, randomized controlled clinical trial (RCT). Materials and Methods: One operator restored 60 Class I occlusal cavities in 24 patients. Preheating of nanoceramic RBC to 60°C for 10 min was performed before insertion of the material into 30 prepared cavities, whereas 30 restorations in the nonpreheated group were placed according to the manufacturer's instructions. Two observers evaluated the restorations using Federation Dentaire Internationale (FDI) criteria at baseline, 6, 12, and 18 months. Statistical Analysis: Kappa index, Friedman and Wilcoxon matched pair test, and Krushal-Wallis and Mann-Whitney tests were used for statistical analysis. Results: 100% retention rates were seen in both the groups. In nonpreheated group, significant difference was observed for surface staining (P = 0.0001), color stability (P = 0.0277), anatomic form (P = 0.0431), and marginal adaptation (P = 0.0051), whereas in preheated group, significant increase in surface staining (P = 0.0051) was recorded. There was a statistically significant difference observed between the preheated and nonpreheated groups at different time periods for the tested clinical parameters. Conclusion: Within the limitations of this RCT of 18 months, preheated nanoceramic RBC restorations showed better clinical performance compared to nonpreheated group.

RESUMEN

Abstract The aim of this study was to investigate the effect of preheating three bulk-fill and one conventional composite resin on the Vickers microhardness and depth of cure of these composites. In this study, three bulk-fill composites- SDR Plus (SDR), Estelite BULK FILL Flow (EST), Admira® Fusion x-tra (AFX), and one conventional composite resin G-ænial POSTERIOR (GP) were used as the control group. The samples were obtained at room temperature (24°C) and at 55°C in T2 mode after being placed in a heating device for 10 minutes. The samples were divided into eight groups (n=10) according to the type of material and heating process that was utilized (preheated and nonheated). All samples were tested with a Vickers microhardness (VHN) tester on the bottom and top surfaces. The first measurements were obtained at baseline; the second set of measurements was performed after the samples were stored in distilled water at 37°C for 24 hours. The depth of cure was calculated using a bottom/top hardness ratio of measurements. Statistical analysis was performed utilizing the SPSS V23 and Shapiro-Wilk tests. Lastly, the Duncan test was used for multiple comparisons (p<0.05). While the VHN increased after the preheating procedure in bulk-fill composites, it decreased in GP. There was no difference between the baseline and the 24-hour VHN values in SDR and GP. After 24 hours, while the VHN of EST increased, the VHN of AFX decreased. There was no difference between the hardness ratios of the AFX and EST samples (p<0.001) and hardness ratios were greater than GP and SDR. When comparing the baseline and the 24- hour values, the VHN depended on the type of materials. Sufficient curing depth was obtained in all groups with a thickness of 2mm.

Resumen El objetivo fue investigar el efecto del precalentamiento de tres resinas Bulk-fill, una resina compuesta convencional sobre la microdureza Vickers y la profundidad de curado de estas resinas. Se utilizaron tres composites Bulk-Fill-SDR Plus (SDR), Estelite BULK FILL Flow (EST), Admira® Fusion x-tra (AFX), y una resina compuesta convencional G-ænial POSTERIOR (GP) como grupo de control. Las muestras se obtuvieron a temperatura ambiente (24°C) y a 55°C en modo T2 después de haber sido colocadas en un dispositivo de calentamiento durante 10 minutos. Se dividieron en ocho grupos (n=10) según el tipo de material y el proceso de calentamiento que se utilizó (precalentado y no calentado). Se probaron con un medidor de microdureza Vickers (VHN) en las superficies inferior y superior. Las primeras mediciones se obtuvieron en la línea de base; la segunda se realizó después de que las muestras se almacenaran en agua destilada a 37°C durante 24 horas. La profundidad de curado se calculó utilizando una relación de dureza inferior/ superior de las mediciones. El análisis estadístico se realizó utilizando el SPSS V23 y las pruebas de Shapiro-Wilk. Por último, se utilizó la prueba de Duncan para las comparaciones múltiples (p<0,05). VHN aumentó tras el procedimiento de precalentamiento en las resina Bulk-Fill, disminuyó en los GP. No hubo diferencias entre los valores de VHN de referencia y de 24 horas en SDR y GP. Después de 24 horas, mientras que el VHN de EST aumentó, el VHN de AFX disminuyó. No hubo diferencias entre los ratios de dureza de las muestras de AFX y EST (p<0,001) y los ratios de dureza fueron mayores que los de GP y SDR. Al comparar los valores de referencia y los de 24 horas, el VHN dependió del tipo de materiales. Se obtuvo una profundidad de curado suficiente en todos los grupos con un grosor de 2mm.

Asunto(s)

RESUMEN

With the aim to design bioactive dental restorative material, the present study investigated the influence of the antimicrobial agents chlorhexidine diacetate (CHX) and octinidine (di)hydrochloride (ODH) when incorporated in two different materials. Selected parameters were polymerization enthalpy, short-term drug release, and the effect on Streptococcus mutans as well as human gingival fibroblasts. Samples were made by mixing a nano-hybrid ormocer (O) and a methacrylate-based nano-hybrid composite (C), each with a mass fraction of 2% CHX or ODH. Release profiles and concentrations of active agents from the resins were assessed, and the cell proliferation of human gingival fibroblasts as well as Streptococcus mutans cultured with the eluates were evaluated. The influence on polymerization was assessed by means of differential scanning calorimetry. Both drugs, especially ODH, showed a decreasing effect on polymerization enthalpies associated with a lowered crosslinking degree. At the same time ODH appeared to be released more persistently than CHX. Moreover, ODH was more efficient with regard to bacteria growth inhibition but also more cytotoxic in terms of reduction of cell viability. ODH is deemed more appropriate for application in a dental resin-based drug delivery system, because of the more persistent drug release than seen for CHX.

Asunto(s)

RESUMEN

The present study reports on the long-term drug release and mechanical properties of bioactive dental filling materials based on chlorhexidine diacetate (CHX) or octinidine (di)hydrochloride (ODH) incorporated in a composite based on dimethacrylates or an ormocer. CHX or ODH were added to a nano-hybrid ormocer (O) and a nano-hybrid composite (C) with the amount of 2 wt% to achieve four matrix-drug combinations: O-CHX, O-ODH, C-CHX, and C-ODH. Drug extraction and release were measured using high-performance liquid chromatography with diode-array detection (HPLC-DAD), while drug distribution was assessed by using energy dispersive X-ray spectroscopy (EDX). Drug release in water at 37°C was observed over 87 d. To determine the material properties, the water absorption, water solubility, flexural strength and hardness were measured and compared to the reference materials. Persistent drug release over 87 d was observed for both ODH-based systems and both ormocer-systems, with the longest duration of activity seen for the O-ODH combination. Persistent drug release was achieved via the loosening of the polymer network indicated via decreasing polymerization enthalpies, enhanced water absorption, and water solubility. As a consequence, the flexural strengths of the materials were reduced. However, surface hardness was hardly reduced. ODH seems to be more adequate than CHX for the design of bioactive dental filling materials based on nano-hybrid ormocer and composites.

Asunto(s)

RESUMEN

Objective: The present study compared the effect of whitening mouthrinses (WM) on the color change of stained resin composites (RC). Material and Methods: Cylindrical specimens (6mm-diameter and 1mm-thickness) were prepared with the following RC (n=60/group): Filtek Z350XT (Z350- methacrylate-based), Admira Fusion (AD- ormocer-based), TPH3 (TPH- methacrylate-based), and Beautifil II (BII- giomer/methacrylate-based). The initial color was assessed with reflectance spectrophotometer using CIE L*a*b* system. The specimens were immersed in staining broth during 14 days, submitted to color evaluation (ΔE1) and randomly allocated in 4 subgroups (n=15), according to WM adopted: Listerine Whitening (LW-2% hydrogen peroxide), Plax Whitening (PW-1.5% hydrogen peroxide), Bromelain/papain (BP-experimental solution), and Deionized water (DW-negative control). The whitening cycle consisted of RC immersion in WM for 1 min and in artificial saliva for 30 min, simulating 12 weeks, and final color assessment was performed (ΔE2). Color change data were analysed by ANOVA and Tukey's tests (α=5%). Results: After staining, TPH showed the lowest ΔE1 values and Z350 showed the highest color change (p=0.001). The whitening effect promoted by LW was significantly higher than color alteration obtained with PW (ΔE2), and BII showed the highest color change values (ΔE2) after whitening cycle. Conclusion: LW exhibited the greatest whitening potential on stained RC, mainly with the Giomer (Beautifill II) and the Ormocer-based (Admira Fusion) materials. Bromelain/papain solution showed no whitening effect on stained RC. (AU)

Objetivo: O presente estudo comparou o efeito de enxaguatórios clareadores (EC) na alteração de cor de resinas compostas (RC) previamente manchadas. Material e Métodos: Espécimes cilíndricos (6mm de diâmetro e 1mm de espessura) foram preparados com as seguintes RC (n=60/grupo): Filtek Z350XT (Z350- metacrilato), Admira Fusion (AD- ormocer), TPH3 (TPH- metacrilato), e Beautifil II (BII- giomer/metacrilato). A cor inicial foi mensurada com espectrofotômetro de reflectância utilizando o sistema CIE L*a*b*. Os espécimes foram imersos em um caldo de manchamento durante 14 dias, submetidos a avaliação de cor (ΔE1) e alocados aleatoriamente em 4 subgrupos (n=15), de acordo com EC adotado: Listerine Whitening (LW-peróxido de hidrogênio a 2%), Plax Whitening (PW- peróxido de hidrogênio a 1,5%), Bromelina/papaína (BP-solução experimental), e Água deionizada (AD- controle negativo). O ciclo clareador consistiu na imersão da RC no EC por 1 min e na saliva artificial por 30 min, simulando 12 semanas, e a cor final foi mensurada (ΔE2). Os dados de alteração de cor foram analisados pelos testes ANOVA e Tukey (α=5%). Resultados: Após o manchamento, TPH apresentou o menor valor de ΔE1 e Z350 apresentou a maior alteração de cor (p=0,001). O efeito clareador promovido pelo LW foi significativamente maior que o obtido com o PW (ΔE2) e BII teve a maior alteração de cor (ΔE2) após o ciclo clareador. Conclusão: LW exibiu maior potencial clareador nas RC manchadas. BII apresentou maior alteração de cor em resposta à ação clareadora de ambos enxaguatórios à base de peróxido de hidrogênio testados.(AU)

Asunto(s)

RESUMEN

The aim of this in vitro study was to investigate the degree of C=C double bond conversion of high-viscosity dimethacrylate- or ormocer-based bulk-fill composites as a function of measurement depth. Four bulk-fill composites (Tetric EvoCeram Bulk Fill, x-tra fil, SonicFill, and Bulk Ormocer) and the conventional nanohybrid composite Tetric EvoCeram were applied in standardized Class II cavities (n = 6 per group) and photoactivated for 20 s at 1350 mW/cm2. The degree of conversion of the composites was assessed using Fourier-transform infrared spectroscopy at seven measurement depths (0.15, 1, 2, 3, 4, 5, 6 mm). Data were analyzed using repeated measures ANOVA and one-way ANOVA with Bonferroni post-hoc tests (α = 0.05). The investigated bulk-fill composites showed at least 80% of their maximum degree of conversion (80% DCmax) up to a measuring depth of at least 4 mm. Tetric EvoCeram Bulk Fill and Bulk Ormocer achieved more than 80% DCmax up to a measuring depth of 5 mm, x-tra fil up to 6 mm. The conventional nanohybrid composite Tetric EvoCeram achieved more than 80% DCmax up to 3 mm. In contrast to the conventional composite, the investigated ormocer- and dimethacrylate-based bulk-fill composites can be photo-polymerized in thick layers of up to at least 4 mm with regard to their degree of C=C double bond conversion.

RESUMEN

The study aimed to evaluate the adhesive performances of two ormocer materials and two micro-hybrid composites placed to restore class II cavities. We tested the null hypothesis, which considered that the adhesive behaviors of tested materials did not differ. On each extracted tooth, two class II cavities were prepared having an enamel located cervical margin and a cementum located cervical margin, respectively, and were restored using two different restoration techniques. The teeth followed a tooth impregnating protocol and were sectioned and evaluated by optical microscopy to highlight the marginal microleakage around restorations. Cervical and occlusal microleakage as well as microleakage ratios were calculated. The microleakage test showed that all tested materials exhibited some degree of dentinal microleakage both on cervical and occlusal areas irrespective of the restoration technique. Some significant differences were recorded in adhesion performance of the materials. The cervical microleakage ratio was significantly increased for one of the micro-hybrid resin composites in comparison with one of the ormocer materials (p = 0.0159). Significantly differences were observed in occlusal microleakage ratios when the two micro-hybrid composites were compared (p = 0.047). The results failed to reject the null hypothesis. The present study could not demonstrate the superiority of ormocer-materials relative to conventional composites.

RESUMEN

The purpose of the in vitro study presented in this paper was to determine the long-term release of fluoride ions from selected ormocer materials (Admira (A), Admira Flow (AF), Admira Seal (AS)). The release of fluoride ions from these materials into a saline solution (0.9% NaCl) and deionized water was tested for 14 weeks. In a long-term study the measurements were taken after 1 and 3 h, then 1, 2, and 3 days and then at weekly intervals for 14 weeks. In a short-term study the measurements were made after 3, 24, 48, 72, 69, 168 h, i.e., within 7 days. All materials used in the test showed a constant level of fluoride release. The highest level of cumulative release of fluoride ions into deionized water was found in the AS material (23.95 ± 4.30 µg/mm2), slightly lower in the A material (23.26 ± 4.16 µg/mm2) and the lowest in the AF material (16.79 ± 2.26 µg/mm2). The highest level of cumulative release into saline solution was found in AF (8.08 ± 1.30 µg/mm2), slightly lower in AS (7.36 ± 0.30 µg/mm2) and the lowest in A (6.73 ± 1.10 µg /mm2). After 1 h of immersion of the samples in the saline solution, the highest level of fluoride was released by AF (0.57 ± 0.06 µg/mm2) followed by A (0.20 ± 0.03 µg/mm2) and AS (0.19 ± 0.02 µg/mm2). Moreover, in the 14-week study, the total amount of fluoride release into the saline, which imitates the environment of the oral cavity, was observed as the highest in the AF sample.

RESUMEN

AIM: Aim of this literature overview was to analyze the diagnostic procedures of hidden caries lesions and to present a restorative protocol. METHODS: A literature overview was performed in order to evaluate hidden caries etiological hypothesis and the reported prevalence. The diagnostic procedure is performed with the aid of an intra-oral fluorescence based camera and the restorative procedure is completed with the use of a novel bisphenol-A free composite. RESULTS: Non cavitated occlusal caries lesions prevalence is high in young adults population. Diagnosis of hidden caries requires both high sensitivity and specificity. CONCLUSIONS: The novel diagnostic and restorative protocol showed to be highly effective in hidden caries assessment and restoration.

Asunto(s)

RESUMEN

Acidic conditions of the oral cavity, including soft drinks and cariogenic bacteria, represent a damage for restorative biomimetic composite materials. The aim of this study is to assess the influence of two different acidic challenges on the flexural strength and elastic modulus of five composites: x-tra fil (Group 1, XTF), GrandioSO x-tra (Group 2, GXT), Admira Fusion x-tra (Group 3, AFX), VisCalor bulk (Group 4, VCB), and Enamel Plus HRi (Group 5, EPH). Thirty samples for each group were randomly divided and assigned to three different treatments: storage in distilled water as the controls (subgroups 1a-5a), 3 weeks distilled water + 1 week Coca-Cola (subgroups 1b-5b), and 4 weeks Coca-Cola (subgroups 1c-5c). For each subgroup, the flexural strength and elastic modulus were measured using an Instron universal testing machine, and data were submitted to statistical analysis. Considering subgroups B, no material showed a significant difference in the flexural strength with the controls (p > 0.05), whereas for subgroups C, only GXT and VCB showed significantly lower values (p < 0.05). AFX reported the lowest flexural strength among the materials tested. As regards the elastic modulus, no material showed a significant variation after acidic storages when compared with the respective control (p > 0.05). AFX and EPH reported the lowest elastic modulus compared to the other materials. All composites tested showed adequate flexural properties according to the standards, except for AFX. This biomimetic material, along with EPH, might be indicated for V class (cervical) restorations considering the lowest values of elasticity reported.

RESUMEN

OBJECTIVE: The aim of this study was to evaluate the influence of a liner on the clinical performance of deep posterior restorations performed with bulk-fill composite. METHODS: 30 subjects received two restorations on deep preparations in posterior teeth, without pulpal exposure, after selective carious-tissue removal in one-stage. The internal walls reached the inner quarter of dentin, but with a radiographically detectable zone of firm dentin remaining. The pulpal protection using a layer of glass ionomer composite liner (Ionoseal, Voco) was applied in just one preparation. The adhesive system Futurabond U (Voco) was applied in all preparations, which were restored with the bulk-fill pure Ormocer nanohybrid composite (Admira Fusion Xtra - Voco), in up to 4 mm thick increments. All restorations were evaluated using the FDI criteria after 7 days, 6, 12 and 24 months postoperatively. RESULTS: After 24-months, 25 patients attended the recall and 50 restorations were evaluated. The Fisher's statistical analysis (5%) showed no difference between the techniques for the esthetic, functional and biological properties. No postoperative sensitivity was reported for both groups. CONCLUSION: The application of a liner did not influence the clinical performance of deep restorations with bulk-fill Ormocer composite. CLINICAL RELEVANCE: The application of a liner with a GIC-based material did not have a significant effect on the clinical performance of bulk-fill restorations and seems to be unnecessary for the material tested.

Asunto(s)

RESUMEN

Optical sensors based on guided mode resonance (GMR) realized in polymers are promising candidates for sensitive and cost effective strain sensors. The benefit of GMR grating sensors is the non-contact, easy optical read-out with large working distance, avoiding costly alignment and packaging procedures. The GMR gratings with resonance around 850-900 nm are fabricated using electron beam lithography and replicated using a soft stamp based imprinting technique on 175 µ m-thick foils to make them suitable for optical strain sensing. For the strain measurements, foils are realized with both GMR gratings and waveguides with Bragg gratings. The latter are used as reference sensors and allow extracting the absolute strain sensitivity of the GMR sensor foils. Following this method, it is shown that GMR gratings have an absolute strain sensitivity of 1.02 ± 0.05 p m / µ ϵ at 870 nm.