RESUMEN

The continuous development and application of laser technology, and the increasing energy and power of laser output have promoted the development of various types of laser optical systems. The optical components based on quartz materials are key components of high-power laser systems, and their quality directly affects the load capacity of the system. Due to the photothermal effect when the laser interacts with the quartz material and generates extremely high temperatures in a short period of time, it is impossible to experimentally solve the phenomena and physical mechanisms under extreme conditions. Therefore, it is very important to select a suitable method to investigate the thermal effect of intense laser interaction with quartz materials and explain the related physical mechanism. In this study, a three-dimensional quarter-symmetric laser heating quartz material geometry model by using nonlinear transient finite element method was established, and its transient temperature field distribution of the quartz material after being heated by a 1,064 nm continuous laser was investigated. In addition, the influence of different laser parameters (laser spot radius, heat flux and irradiation time), material parameters (material thickness, material absorption rate of laser) on the thermal effect of heating quartz material were also studied. When the laser heat flux is 20 W/cm2, the diameter of the laser spot is 10 cm, the irradiation time is 600 s and the thickness is 4 cm, the temperature after laser heating can reach 940.18°C, which is far lower than the melting point. In addition, the temperature maximum probes were set at the overall model, spot edge and rear surface respectively, and their temperature rise curves with time were obtained. It is also found that there is a significant hysteresis period for the rear surface temperature change of the quartz material compared with the overall temperature change due to heat conduction. Finally, the method proposed can also be applied to the laser heating of other non-transparent materials.

RESUMEN

Introduction: The purpose of this study is to achieve a significant increase in the proliferative activity of mesenchymal stem cells (MSCs) of the bone marrow (BM) at early passages after laser exposure to a suspension of these cells and to estimate the effect of light and heat components of laser radiation on the proliferation of BM MSCs. Methods: The studies were performed on rats BM MSCs. MSC suspension was placed into the wells and heated by using laser radiation (980 nm wavelength) or a water bath at 70 °C providing similar temperature dynamics. The studies were carried out in 3 comparison groups: (1) control suspension of MSCs, which was not subjected to heating in a water bath or laser exposure; (2) MSC suspension, which was heated for in a water bath; and (3) suspension of MSCs, which was subjected to laser exposure. The exposure times for the 2nd and 3rd experimental groups were 10- 50 seconds. Results: Under optimal parameters of laser action on the suspension of BM MSCs, a six-fold increase in the number of BM MSCs colonies was registered compared to the control. The role of the light and heat components of laser exposure to MSCs was determined by comparable heating of a suspension of BM MSCs in a water bath, at which only a twofold increase in the number of colonies was maximally obtained. Conclusion: The increase in the MSC proliferation activity occurs due to their Thermo-Photobiomodulation. The result obtained is important for practical use in cell transplantation in the treatment of traumatic injuries of bone, cartilage, and tendon tissues when a rapid and multiple increase in the initial number of autologous BM MSCs is required.

RESUMEN

Laser therapy has been widely used to treat port-wine stains (PWS) and other cutaneous vascular lesions via selective photothermolysis. Animal models are a valuable tool for investigating thermal responses beneath the skin. However, in previous animal experiments, such as the dorsal skin chamber model, one side of the skin was removed, resulting in the loss of mechanical support for the target blood vessel. In this study, the optical clearing technique was applied to the dorsal skin, allowing direct observation of real thermal responses within the tissue without removing the covering skin. The target blood vessels were irradiated with a pulsed 1064 nm Nd: YAG laser. The corresponding thermal responses were recorded using a CCD camera. Additionally, variations in skin reflectance spectra were measured before and after laser irradiation. Due to the optical clearing and reflectance spectra measurement, vessel responses such as contraction, reperfusion, and full occlusion were correlated with specific variation patterns in reflectance spectral signals.

Asunto(s)

RESUMEN

In this study, we report the synthesis of a new cubic neodymium-rhenium metallic alloy NdRe2 through the utilization of high pressure and laser heating in a diamond anvil cell. NdRe2 crystallizes in the Fd3¯m space group with a lattice parameter equal to 7.486 (2) Å and Z = 8 at 24 (1) GPa and 2,200 (100) K. It was studied using high-pressure single-crystal X-ray diffraction. The compound crystallizes in the cubic MgCu2 structure type. Its successful synthesis further proves that high-pressure high-temperature conditions can be used to obtain alloys holding a Laves phase structure. Ab initio calculations were done to predict the mechanical properties of the material. We also discuss the usage of extreme conditions to synthesize and study materials present in the nuclear waste.

RESUMEN

The deterministic preparation of highly ordered single-crystalline surfaces is a key step for studying and utilizing the physical properties of various advanced materials. This paper presents the fast and straightforward preparation of vicinal Al2O3(0001) surfaces with micrometer-scale atomic order. Crisp electron-diffraction spots up to at least 20th order evidence atomic coherence on terraces with widths exceeding 1 µm. The unique combination of three properties of Al2O3(0001) underlie this remarkable coherence: its high-temperature stability; the differences in the ionic bonding systems of the surface as compared to the bulk; and the fact that the terraces are non-polar whereas the step edges have a polar character. The step edges are furthermore found to have alternating configurations, which drive a step-doubling transition. On double-stepped surfaces, the Al-rich ( 31 × 31 ) R ± 9 $(\sqrt {31}\times \sqrt {31})\textrm {R}\pm 9$ ° surface reconstruction attains a singular in-plane orientation. These results set a benchmark for high-quality surface preparation and thus expand the scope for both fundamental studies on and the technological utilization of exciting material systems.

RESUMEN

Switchable adhesive is essential to develop transfer printing, which is an advanced heterogeneous material integration technique for developing electronic systems. Designing a switchable adhesive with strong adhesion strength that can also be easily eliminated to enable noncontact transfer printing still remains a challenge. Here, we report a simple yet robust design of switchable adhesive based on a thermally responsive shape memory polymer with micropillars of different heights. The adhesive takes advantage of the shape-fixing property of shape memory polymer to provide strong adhesion for a reliable pick-up and the various levels of shape recovery of micropillars under laser heating to eliminate the adhesion for robust printing in a noncontact way. Systematic experimental and numerical studies reveal the adhesion switch mechanism and provide insights into the design of switchable adhesives. This switchable adhesive design provides a good solution to develop laser-driven noncontact transfer printing with the capability of eliminating the influence of receivers on the performance of transfer printing. Demonstrations of transfer printing of silicon wafers, microscale Si platelets, and micro light emitting diode (µ-LED) chips onto various challenging nonadhesive receivers (e.g., sandpaper, stainless steel bead, leaf, or glass) to form desired two-dimensional or three-dimensional layouts illustrate its great potential in deterministic assembly.

RESUMEN

Two-dimensional nanomaterials have obvious advantages in thermoelectric device development. It is rare to use the same experimental system to accurately measure multiple thermoelectrical parameters of the same sample. Therefore, scholars have developed suspended microdevices, T-type and H-type methods to fulfill the abovementioned requirements. These methods usually require a direct-current voltage signal to detect in Seebeck coefficient measurement. However, the thermoelectric potential generated by the finite temperature difference is very weak and can be easily overwritten by the direct-current voltage, thereby affecting the measurement accuracy. In addition, these methods generally require specific electrodes to measure the thermoelectric potential. We propose a measurement method that combines laser heating with an H-type device. By introducing a temperature difference in two-dimensional materials through laser heating, the thermoelectric potential can be accurately measured. This method does not require specific electrodes to simplify the device structure. The thermoelectrical parameters of supported graphene are successfully measured with this method; the results are in good agreement with the literature. The proposed method is unaffected by material size and characteristics. It has potential application value in the characterization of thermoelectric physical properties.

RESUMEN

Reliable thermophysical properties of core melt (corium) are essential for the accurate prediction of the severe accident progression in light water reactors. Zirconia is one of the most important materials in corium. Despite the high interest in the viscosity of molten zirconia, few experimental data have been reported due to its high melting temperature and high vapor pressure. In the present study, the viscosity of molten zirconia was measured using aerodynamic levitation, laser heating and droplet oscillation techniques. A material sample was levitated by argon gas flow in a conical nozzle and then melted into a droplet by laser beams. The initial quiescent droplet was forced to oscillate by the excitation of a loudspeaker, and the viscosity was deduced based on the characteristics of the droplet damped oscillation after the loudspeaker was turned off. The viscosity of molten alumina was first measured for verification of the measurement system. Afterwards the viscosity of molten zirconia was measured. The results showed that the viscosity of molten zirconia at melting temperature (2988K) was 12.87 ± 1.03 mPa s and decreased with increasing temperature. The measurement uncertainties are within 21 %.

RESUMEN

Diamond's unique properties on the nanoscale make it one of the most important materials for use in biosensors and quantum computing and for components that can withstand the harsh environments of space. We synthesize oriented, faceted diamond particles by flash laser heating of glassy carbon at 16 GPa and 2300 K. Detailed transmission electron microscopy shows them to consist of a mosaic of diamond nanocrystals frequently joined at twin boundaries forming microtwins. Striking 3-fold translational periodicity was observed in both imaging and diffraction. This periodicity was shown to originate from nanodimensional wedge-shaped overlapping regions of twinned diamond and not from a possible 9R polytype, which has also been reported in other group IVa elements and water ice. Extended bilayers of hexagonal layer stacking were observed, forming lonsdaleite nanolaminates. The particles exhibited optical fluorescence with a rapid quench time (<1 ns) attributed to their unique twinned microstructure.

RESUMEN

The water pollution caused by the release of organic pollutants has attracted remarkable attention, and solutions for wastewater treatment are being developed. In particular, the photocatalytic removal of organic pollutants in water systems is a promising strategy to realize the self-cleaning of ecosystems under solar light irradiation. However, at present the semiconductor-based nanocatalysts can barely satisfy the industrial requirements because their wide bandgaps restrict the effective absorption of solar light, which needs an energy band modification to boost the visible light harvesting via surface engineering. As an innovative approach, pulsed laser heating in liquids has been utilized to fabricate the nanomaterials in catalysis; it demonstrates multi-controllable features, such as size, morphology, crystal structure, and even optical or electrical properties, with which photocatalytic performances can be precisely optimized. In this review, focusing on the powerful heating effect of pulsed laser irradiation in liquids, the functional nanomaterials fabricated by laser technology and their applications in the catalytic degradation of various organic pollutants are summarized. This review not only highlights the innovative works of pulsed laser-prepared nanomaterials for organic pollutant removal in water systems, such as the photocatalytic degradation of organic dyes and the catalytic reduction of toxic nitrophenol and nitrobenzene, it also critically discusses the specific challenges and outlooks of this field, including the weakness of the produced yields and the relevant automatic strategies for massive production.

RESUMEN

The features of oxidation of ultra-high-temperature ceramic material HfB2-30 vol.%SiC modified with 1 vol.% graphene as a result of supersonic flow of dissociated CO2 (generated with the use of high-frequency induction plasmatron), as well as under the influence of combined heating by high-speed CO2 jets and ytterbium laser radiation, were studied for the first time. It was found that the addition of laser radiation leads to local heating of the central region from ~1750 to ~2000-2200 °C; the observed temperature difference between the central region and the periphery of ~300-550 °C did not lead to cracking and destruction of the sample. Oxidized surfaces and cross sections of HfB2-SiC-CG ceramics with and without laser heating were investigated using X-ray phase analysis, Raman spectroscopy and scanning electron microscopy with local elemental analysis. During oxidation by supersonic flow of dissociated CO2, a multilayer near-surface region similar to that formed under the influence of high-speed dissociated air flows was formed. An increase in surface temperature with the addition of laser heating from 1750-1790 to 2000-2200 °C (short term, within 2 min) led to a two to threefold increase in the thickness of the degraded near-surface area of ceramics from 165 to 380 microns. The experimental results indicate promising applications of ceramic materials based on HfB2-SiC as part of high-speed flying vehicles in planetary atmospheres predominantly composed of CO2 (e.g., Venus and Mars).

Asunto(s)

RESUMEN

We report the P-V-T equation of state measurements of B4C to 50 GPa and approximately 2500 K in laser-heated diamond anvil cells. We obtain an ambient temperature, third-order Birch-Murnaghan fit to the P-V data that yields a bulk modulus K0 of 221(2) GPa and derivative, (dK/dP)0 of 3.3(1). These were used in fits with both a Mie-Grüneisen-Debye model and a temperature-dependent, Birch-Murnaghan equation of state that includes thermal pressure estimated by thermal expansion (α) and a temperature-dependent bulk modulus (dK0/dT). The ambient pressure thermal expansion coefficient (α0 + α1T), Grüneisen γ(V) = γ0(V/V0)q and volume-dependent Debye temperature, were used as input parameters for these fits and found to be sufficient to describe the data in the whole P-T range of this study. This article is part of the theme issue 'Exploring the length scales, timescales and chemistry of challenging materials (Part 1)'.

RESUMEN

Fused filament fabrication is one of the most desired thermal plastic additive manufacturing processes because of its ability to fabricate complex objects with high accessibility. However, due to the extrusion track-based direct write process mechanism, parts built using this method exhibit anisotropic mechanical properties. In this work, an in-process laser heating method is introduced to heal interface adhesion between adjacent deposited tracks by increasing the interface temperature to promote polymer reptation and enhance bonding strength of the interface of adjacent tracks. With the use of laser heating induced interface healing, the measured flexural strength between adjacent tracks in the same layer increased and exceeded that of the control sample tested along the track direction. The effect of laser on interface healing was also verified by investigating the load-displacement curve and morphology analysis of the fractured surface.

RESUMEN

Combining experimental set up and ab initio molecular dynamics simulations, we were able to follow the time evolution of the X-ray absorption near edge spectrum (XANES) of a dense copper plasma. This provides a deep insight into femtosecond laser interaction with a metallic copper target. This paper presents a review of the experimental developments we made to reduce the X-ray probe duration, from approximately 10 ps to fs duration with table-top laser systems. Moreover, we present microscopic scale simulations, performed with Density Functional Theory, as well as macroscopic simulations considering the Two-Temperature Model. These tools allow us to get a complete picture of the evolution of the target at a microscopic level, from the heating process to the melting and expansion stages, with a clear view of the physics involved during these processes. This article is part of the theme issue 'Dynamic and transient processes in warm dense matter'.

RESUMEN

We present a sessile droplet manipulation platform that enables the formation and transport of a droplet on a light-absorbing surface via local laser-beam irradiation. The mechanism relies on solutocapillary Marangoni flow arising from a concentration gradient in a binary mixture liquid. Because the mixture is strongly confined in a two-dimensional slit with a spacing of a few micrometers, the wetting film is stably sustained, enabling the rapid formation, deformation, and transport of a sessile droplet. In addition, to sustain the droplet in the absence of laser irradiation, we developed a method to bridge the droplet between the top and bottom walls of the slit. The bridge is stably sustained because of the hydrophilicity of the slit wall. Splitting and merging of the droplet bridges are also demonstrated.

RESUMEN

WTe2, a low-symmetry transition metal dichalcogenide, has broad prospects in functional device applications due to its excellent physical properties. When WTe2 flake is integrated into practical device structures, its anisotropic thermal transport could be affected greatly by the substrate, which matters a lot to the energy efficiency and functional performance of the device. To investigate the effect of SiO2/Si substrate, we carried out a comparative Raman thermometry study on a 50 nm-thick supported WTe2 flake (with κzigzag = 62.17 W·m-1·K-1 and κarmchair = 32.93 W·m-1·K-1), and a suspended WTe2 flake of similar thickness (with κzigzag = 4.45 W·m-1·K-1, κarmchair = 4.10 W·m-1·K-1). The results show that the thermal anisotropy ratio of supported WTe2 flake (κzigzag/κarmchair ≈ 1.89) is about 1.7 times that of suspended WTe2 flake (κzigzag/κarmchair ≈ 1.09). Based on the low symmetry nature of the WTe2 structure, it is speculated that the factors contributing to thermal conductivity (mechanical properties and anisotropic low-frequency phonons) may have affected the thermal conductivity of WTe2 flake in an uneven manner when supported on a substrate. Our findings could contribute to the 2D anisotropy physics and thermal transport study of functional devices based on WTe2 and other low-symmetry materials, which helps solve the heat dissipation problem and optimize thermal/thermoelectric performance for practical electronic devices.

RESUMEN

Phase velocity of surface acoustic waves(SAWs) is frequency dependent when propagate on medium with inhomogeneous elasticity over depth. In this work, frequency dependent Time-of-Flight (ToF) variation of SAWs induced by a local and dynamic heating was applied for measurement of temperature dependent shear modulus. Laser-generated broad-band SAWs propagated through the material with elastic properties and density modified by dynamic inhomogeneous temperature field induced by a millisecond laser heating. Sample with spatial dependent material properties introduces phase velocity dispersion in the SAW propagation. As consequence, ToF of SAW becomes frequency dependent. Frequency dependent ToF variation curves at two time instants respected to laser heating were measured by time-frequency analysis together with a differential technique. Free fitted parameters, temperature dependent shear modulus and surface temperature distribution were evaluated by solving the inverse problem by fitting the experimental ToF variation curves into the theoretical ones by means of the differential evolution method. The inversed temperature dependent parameter of shear modulus of Ti-6Al-4V alloy was in good agreement with literature value.

RESUMEN

Selected area deposition of high purity gold films onto nanoscale 3D architectures is highly desirable as gold is conductive, inert, plasmonically active, and can be functionalized with thiol chemistries, which are useful in many biological applications. Here, we show that high-purity gold coatings can be selectively grown with the Me2Au (acac) precursor onto nanoscale 3D architectures via a pulsed laser pyrolytic chemical vapor deposition process. The selected area of deposition is achieved due to the high thermal resistance of the nanoscale geometries. Focused electron beam induced deposits (FEBID) and carbon nanofibers are functionalized with gold coatings, and we demonstrate the effects that laser irradiance, pulse width, and precursor pressure have on the growth rate. Furthermore, we demonstrate selected area deposition with a feature-targeting resolutions of ~100 and 5 µm, using diode lasers coupled to a multimode (915 nm) and single mode (785 nm) fiber optic, respectively. The experimental results are rationalized via finite element thermal modeling.

RESUMEN

This study experimentally and numerically validates the commonly employed technique of laser-induced heating of a material in optical temperature sensing studies. Furthermore, the Er3+-doped glass microspheres studied in this work can be employed as remote optical temperature sensors. Laser-induced self-heating is a useful technique commonly employed in optical temperature sensing research when two temperature-dependent parameters can be correlated, such as in fluorescence intensity ratio vs. interferometric calibration, allowing straightforward sensor characterization. A frequent assumption in such experiments is that thermal homogeneity within the sensor volume, that is, a sound hypothesis when dealing with small volume to surface area ratio devices such as microresonators, but has never been validated. In order to address this issue, we performed a series of experiments and simulations on a microsphere supporting whispering gallery mode resonances, laser heating it at ambient pressure and medium vacuum while tracking the resonance wavelength shift and comparing it to the shift rate observed in a thermal bath. The simulations were done starting only from the material properties of the bulk glass to simulate the physical phenomena of laser heating and resonance of the microsphere glass. Despite the simplicity of the model, both measurements and simulations are in good agreement with a highly homogeneous temperature within the resonator, thus validating the laser heating technique.

RESUMEN

This study proposes a novel use of laser heating to increase the adhesion between coatings fabricated by low-temperature PVD and replaceable cemented carbide cutting inserts, thus extending the life of these cutting tools in the machining of difficult-to-machine materials. Our previous studies conducted on CVD coatings showed that these coatings had higher adhesion due to a much higher process temperature. However, taking into account the fact that PVD coatings have better technological properties (e.g., lower structure porosity, higher hardness, and better tribological properties) than CVD coatings, it is fully justified to investigate ways of improving the PVD coating adhesion to the substrate. In this study, replaceable cutting inserts with different hard coatings of titanium nitride were used. Laser heating was conducted with different power densities. The adhesion strength of the tested coatings was determined via vibration spectrum analysis. In addition, 2D surface imaging, scanning electron microscopy, and X-ray fluorescence spectrometry were employed to examine the coatings after laser heating. A significant increase in the adhesion of single-layer (TiN) and double-layer (TiCN + TiN) coatings to the cemented carbide substrate, together with increased tool life, was observed after heating the samples with 40% of the maximum laser power. The application of a multilayer coating containing thermal shock-sensitive (TiAlSi) N did not increase the tool life. This paper attempts to interpret the obtained results.