RESUMEN
Aqueous calcium ion batteries, promising for energy storage, are still challenged by very limited anode choices. Although a Zn metal anode is popular in aqueous batteries, interface instability due to incessant corrosion and severe Zn dendrites hinders its development. Here, an interphase layer with densely packed nanocrystals of Ca3(CO3)2(OH)2·1.5H2O and ZnF2, and amorphous organic species, is demonstrated for a Zn metal anode with 1 M calcium trifluoromethyl sulfonate aqueous electrolyte. The hybrid interface fully avoids direct Zn-H2O contact, maintains fast ion conductivity, and effectively prevents corrosion and dendrite growth. Therefore, the symmetric cell stably lasts for 1600 h at 0.5 mA cm-2 and 2.5 mAh cm-2, far superior to 150 h for the control cell. Furthermore, the device maintains 80% capacity retention after 700 cycles at 1 A g-1, outperforming 13% retention after 200 cycles for the control device. This work indicates that interface and interphase engineering is also crucial for aqueous batteries.
RESUMEN
Inferior fast-charging and low-temperature performances remain a hurdle for lithium-ion batteries. Overcoming this hurdle is extremely challenging primarily due to the low conductivity of commercial ethylene carbonate (EC)-based electrolytes and the formation of undesirable solid electrolyte interphases with poor Li+-ion diffusion kinetics. Here, a series of EC-free fast-charging electrolytes (FCEs) by incorporating a fluorinated ester, methyl trifluoroacetate (MTFA), as a special cosolvent into a practically viable LiPF6-dimethyl carbonate-fluoroethylene carbonate system, is reported. With a solvent-dominated solvation structure, MTFA facilitates the formation of thin, yet robust, interphases on both the cathode and anode. Commercial 1 Ah graphite|LiNi0.8Mn0.1Co0.1O2 pouch cells filled with the FCE exhibit ≈80% capacity retention over 3000 cycles at 3 C and 4 C (15 min) charging rates in the full range of 0-100% state-of-charge. Moreover, even at a low operating temperature of -20 °C, the 1 Ah cell retains a high capacity of 0.65 Ah at a 2 C discharge rate and displays virtually no capacity fade on cycling at a C/5 rate. The work highlights the power of electrolyte design in achieving extra-fast-charging and low-temperature performances.
RESUMEN
While the formation of an inorganic-rich solid electrolyte interphase (SEI) plays a crucial role, the persistent challenge lies in the formation of an organic-rich SEI due to the high solvent ratio in low-concentration electrolytes (LCEs), which hinders the achievement of high-performance lithium metal batteries. Herein, by incorporating di-fluoroethylene carbonate (DFEC) as a non-solvating cosolvent, a solvation structure dominated by anions is introduced in the innovative LCE, leading to the creation of a durable and stable inorganic-rich SEI. Leveraging this electrolyte design, the Li||NCM83 cell demonstrates exceptional cycling stability, maintaining 82.85% of its capacity over 500 cycles at 1 C. Additionally, Li||NCM83 cell with a low N/P ratio (≈2.57) and reduced electrolyte volume (30 µL) retain 87.58% of its capacity after 150 cycles at 0.5 C. Direct molecular information is utilized to reveal a strong correlation between solvation structures and reduction sequences, proving the anion-dominate solvation structure can impedes the preferential reduction of solvents and constructs an inorganic-rich SEI. These findings shed light on the pivotal role of solvation structures in dictating SEI composition and battery performance, offering valuable insights for the design of advanced electrolytes for next-generation lithium metal batteries.
RESUMEN
Achieving high energy density has always been the goal of lithium-ion batteries (LIBs). SiOx has emerged as a compelling candidate for use as a negative electrode material due to its remarkable capacity. However, the huge volume expansion and the unstable electrode interface during (de)lithiation, hinder its further development. Herein, we report a facile strategy for the synthesis of surface fluorinated SiOx (SiOx@vG-F), and investigate their influences on battery performance. Systematic experiments investigations indicate that the reaction between Li+ and fluorine groups promotes the in-situ formation of stable LiF-rich solid electrolyte interface (SEI) on the surface of SiOx@vG-F anode, which effectively suppresses the pulverization of microsized SiOx particles during the charge and discharge cycle. As a result, the SiOx@vG-F enabled a higher capacity retention of 86.4% over 200 cycles at 1.0 C in the SiOx@vG-F||LiNi0.8Co0.1Mn0.1O2 full cell. This approach will provide insights for the advancement of alternative electrode materials in diverse energy conversion and storage systems.
RESUMEN
Demands for green ammonia production increase due to its application as a proton carrier, and recent achievements in electrochemical Li-mediated nitrogen reduction reactions (Li-NRRs) show promising reliability. Here, it is demonstrated that F-containing additives in the electrolyte improve ammonia production by modulating the solid electrolyte interphase (SEI). It is suggested that the anionic additives with low lowest unoccupied molecular orbital levels enhance efficiency by contributing to the formation of a conductive SEI incorporated with LiF. Specifically, as little as 0.3 wt.% of BF4 - additive to the electrolyte, the Faradaic efficiency (FE) for ammonia production is enhanced by over 15% compared to an additive-free electrolyte, achieving a high yield of 161 ± 3 nmol s-1 cm-2. The BF4 - additive exhibits advantages, with decreased overpotential and improved FE, compared to its use as the bulk electrolyte. The observation of the Li3N upper layer implies that active Li-NRR catalytic cycles are occurring on the outermost SEI, and density functional theory simulations propose that an SEI incorporated with LiF facilitates energy profiles for the protonation by adjusting the binding energies of the intermediates compared to bare copper. This study unlocks the potential of additives and offers insights into the SEIs for efficient Li-NRRs.
RESUMEN
Lithium metal batteries (LMBs), with high energy densities, are strong contenders for the next generation of energy storage systems. Nevertheless, the unregulated growth of lithium dendrites and the unstable solid electrolyte interphase (SEI) significantly hamper their cycling efficiency and raise serious safety concerns, rendering LMBs unfeasible for real-world implementation. Covalent organic frameworks (COFs) and their derivatives have emerged as multifunctional materials with significant potential for addressing the inherent problems of the anode electrode of the lithium metal. This potential stems from their abundant metal-affine functional groups, internal channels, and widely tunable architecture. The original COFs, their derivatives, and COF-based composites can effectively guide the uniform deposition of lithium ions by enhancing conductivity, transport efficiency, and mechanical strength, thereby mitigating the issue of lithium dendrite growth. This review provides a comprehensive analysis of COF-based and derived materials employed for mitigating the challenges posed by lithium dendrites in LMB. Additionally, we present prospects and recommendations for the design and engineering of materials and architectures that can render LMBs feasible for practical applications.
RESUMEN
Zinc metal is a promising anode candidate for aqueous zinc ion batteries due to its high theoretical capacity, low cost, and high safety. However, its application is currently restricted by hydrogen evolution reactions (HER), by-product formation, and Zn dendrite growth. Herein, a "Zn2+ in salt" (ZIS) interphase is in situ constructed on the surface of the anode (ZIS@Zn). Unlike the conventional "Zn2+ in water" working environment of Zn anodes, the intrinsic hydrophobicity of the ZIS interphase isolates the anode from direct contact with the aqueous electrolyte, thereby protecting it from HER, and the accompanying side reactions. More importantly, it works as an ordered water-free ion-conducting medium, which guides uniform Zn deposition and facilitates rapid Zn2+ migration at the interface. As a result, the symmetric cells assembled with ZIS@Zn exhibit dendrite-free plating/striping at 4500 h and a high critical current of 14 mA cm-2. When matched with a vanadium-based (NVO) cathode, the full battery exhibits excellent long-term cycling stability, with 88% capacity retention after 1600 cycles. This work provides an effective strategy to promote the stability and reversibility of Zn anodes in aqueous electrolytes.
RESUMEN
Limited electrochemical stability windows of conventional carbonate-based electrolytes pose a challenge to support the Lithium (Li)- and manganese (Mn)-rich (LMR) high-voltage cathodes in rechargeable Li-metal batteries (LMBs). To address this issue, a novel localized high-concentration electrolyte (LHCE) composition incorporating LiPF6 and LiTFSI as dual-salts (D-LHCE), tailored for high-voltage (>4.6 Vvs.Li) operation of LMR cathodes in LMBs is introduced. 7Li nuclear magnetic resonance and Raman spectroscopy revealed the characteristics of the solvation structure of D-LHCE. The addition of LiPF6 provides stable Al-current-collector passivation while the addition of LiTFSI improves the stability of D-LHCE by producing a more robust cathode-electrolyte interphase (CEI) on LMR cathode and solid-electrolyte interphase (SEI) on Li-metal anode. As a result, LMR/Li cell, using the D-LHCE, achieved 72.5% capacity retention after 300 cycles, a significant improvement compared to the conventional electrolyte (21.9% after 100 cycles). The stabilities of LMR CEI and Li-metal SEI are systematically analyzed through combined applications of electrochemical impedance spectroscopy and distribution of relaxation times techniques. The results present that D-LHCE concept represents an effective strategy for designing next-generation electrolytes for high-energy and high-voltage LMB cells.
RESUMEN
Dendrite growth and side reactions of zinc metal anode have severely limited the practical application of aqueous zinc ion batteries (AZIBs). Herein, we introduce an artificial buffer layer composed of functional MXene (Ti3CN) for zinc anodes. The synthesized Ti3CN exhibits superior conductivity and features duplex zincophilic sites (N and F). These characteristics facilitate the homogeneous deposition of Zn2+, accelerate the desolvation process of hydrated Zn2+, and reduce the nucleation overpotential. The Ti3CN-protected Zn anode demonstrates significantly enhanced reversibility compared to bare Zn anode during long-term cycling, achieving a cumulative plating capacity of 10,000 mAh cm-2 at 10 mA cm-2. In Ti3CN-Zn||Cu asymmetric cell, it maintains nearly 100 % Coulombic efficiency over 2500 cycles at 2 mA cm-2. Furthermore, the assembled Ti3CN-Zn//δ-K0.51V2O5 (KVO) full cell exhibit a low capacity decay rate of 0.002 % per cycle at 5 A/g. Even at 0 °C, the Ti3CN-Zn symmetric cell maintains steady cycling for 2000 h. This study introduces a novel approach for designing artificial solid electrolyte interlayers for commercial AZIBs.
RESUMEN
High-energy-density lithium-metal batteries (LMBs) coupling lithium-metal anodes and high-voltage cathodes are hindered by unstable electrode/electrolyte interphases (EEIs), which calls for the rational design of efficient additives. Herein, we analyze the effect of electron structure on the coordination ability and energy levels of the additive, from the aspects of intramolecular electron cloud density and electron delocalization, to reveal its mechanism on solvation structure, redox stability, as-formed EEI chemistry, and electrochemical performances. Furthermore, we propose an electron reconfiguration strategy for molecular engineering of additives, by taking sorbide nitrate (SN) additive as an example. The lone pair electron-rich group enables strong interaction with the Li ion to regulate solvation structure, and intramolecular electron delocalization yields further positive synergistic effects. The strong electron-withdrawing nitrate moiety decreases the electron cloud density of the ether-based backbone, improving the overall oxidation stability and cathode compatibility, anchoring it as a reliable cathode/electrolyte interface (CEI) framework for cathode integrity. In turn, the electron-donating bicyclic-ring-ether backbone breaks the inherent resonance structure of nitrate, facilitating its reducibility to form a N-contained and inorganic Li2O-rich solid electrolyte interface (SEI) for uniform Li deposition. Optimized physicochemical properties and interfacial biaffinity enable significantly improved electrochemical performance. High rate (10 C), low temperature (-25 °C), and long-term stability (2700 h) are achieved, and a 4.5 Ah level Li||NCM811 multilayer pouch cell under harsh conditions is realized with high energy density (462 W h/kg). The proof of concept of this work highlights that the rational ingenious molecular design based on electron structure regulation represents an energetic strategy to modulate the electrolyte and interphase stability, providing a realistic reference for electrolyte innovations and practical LMBs.
RESUMEN
LiPF6-based carbonate electrolytes have been extensively employed in commercial Li-ion batteries, but they face numerous interfacial stability challenges while applicating in high-energy-density lithium-metal batteries (LMBs). Herein, this work proposes N-succinimidyl trifluoroacetate (NST) as a multifunctional electrolyte additive to address these challenges. NST additive could optimize Li+ solvation structure and eliminate HF/H2O in the electrolyte, and preferentially be decomposed on the Ni-rich cathode (LiNi0.8Co0.1Mn0.1O2, NCM811) to generate LiF/Li3N-rich cathode-electrolyte interphase (CEI) with high conductivity. The synergistic effect reduces the electrolyte decomposition and inhibits the transition metal (TM) dissolution. Meanwhile, NST promotes the creation of solid electrolyte interphase (SEI) rich in inorganics on the Li metal anode (LMA), which restrains the growth of Li dendrites, minimizes parasitic reactions, and fosters rapid Li+ transport. As a result, compared with the reference, the Li/LiNi0.8Co0.1Mn0.1O2 cell with 1.0 wt.% NST exhibits higher capacity retention after 200 cycles at 1C (86.4% vs. 64.8%) and better rate performance, even at 9C. In the presence of NST, the Li/Li symmetrical cell shows a super-stable cyclic performance beyond 500 h at 0.5 mA cm-2/0.5 mAh cm-2. These unique features of NST are a promising solution for addressing the interfacial deterioration issue of high-capacity Ni-rich cathodes paired with LMA.
RESUMEN
The performance of electrochemical batteries is intricately tied to the physicochemical environments established by their employed electrolytes. Traditional battery designs utilizing a single electrolyte often impose identical anodic and cathodic redox conditions, limiting the ability to optimize redox environments for both anode and cathode materials. Consequently, advancements in electrolyte technologies are pivotal for addressing these challenges and fostering the development of next-generation high-performance electrochemical batteries. This review categorizes perspectives on electrolyte technology into three key areas: additives engineering, comprehensive component analysis encompassing solvents and solutes, and the effects of concentration. By summarizing significant studies, the efficacy of electrolyte engineering is highlighted, and the review advocates for further exploration of optimized component combinations. This review primarily focuses on liquid electrolyte technologies, briefly touching upon solid-state electrolytes due to the former greater vulnerability to electrode and electrolyte interfacial effects. The ultimate goal is to generate increased awareness within the battery community regarding the holistic improvement of battery components through optimized combinations.
RESUMEN
With the electrochemical performance of batteries approaching the bottleneck gradually, it is increasingly urgent to solve the safety issue. Herein, all-in-one strategy is ingeniously developed to design smart, safe, and simple (3S) practical pouch-type LiNi0.8Co0.1Mn0.1O2||Graphite@SiO (NCM811||Gr@SiO) cell, taking full advantage of liquid and solid-state electrolytes. Even under the harsh thermal abuse and high voltage condition (100 °C, 3-4.5 V), the pouch-type 3S NCM811||Gr@SiO cell can present superior capacity retention of 84.6% after 250 cycles (based pouch cell: 47.8% after 250 cycles). More surprisingly, the designed 3S NCM811||Gr@SiO cell can efficiently improve self-generated heat T1 by 45 °C, increase TR triggering temperature T2 by 40 °C, and decrease the TR highest T3 by 118 °C. These superior electrochemical and safety performances of practical 3S pouch-type cells are attributed to the robust and stable anion-induced electrode-electrolyte interphases and local solid-state electrolyte protection layer. All the fundamental findings break the conventional battery design guidelines and open up a new direction to develop practical high-performance batteries.
RESUMEN
Lithium batteries employing Li or silicon (Si) anodes hold promise for the next-generation energy storage systems. However, their cycling behavior encounters rapid capacity degradation due to the vulnerability of solid electrolyte interphases (SEIs). Though anion-derived SEIs mitigate this degradation, the unavoidable reduction of solvents introduces heterogeneity to SEIs, leading to fractures during cycling. Here, we elucidate how the reductive stability of solvents, dominated by the electrophilicity (EPT) and coordination ability (CDA), delineates the SEI formed on Li or Si anodes. Solvents exhibiting lower EPT and CDA demonstrate enhanced tolerance to reduction, resulting in inorganic-rich SEIs with homogeneity. Guided by these criteria, we synthesized three promising solvents tailored for Li or Si anodes. The decomposition of these solvents is dictated by their EPTs under similar solvation structures, imparting distinct characteristics to SEIs and impacting battery performance. The optimized electrolyte, 1â M lithium bis(fluorosulfonyl)imide (LiFSI) in N-Pyrrolidine-trifluoromethanesulfonamide (TFSPY), achieves 600 cycles of Si anodes with a capacity retention of 81 % (1910â mAh g-1). In anode-free Cu||LiNi0.5Co0.2Mn0.3O2 (NCM523) pouch cells, this electrolyte sustains over 100 cycles with an 82 % capacity retention. These findings illustrate that reducing solvent decomposition benefits SEI formation, offering valuable insights for the designing electrolytes in high-energy lithium batteries.
RESUMEN
Traditional lithium salts are difficult to meet practical application demand of lithium metal batteries (LMBs) under high voltages and temperatures. LiPF6, as the most commonly used lithium salt, still suffers from notorious moisture sensitivity and inferior thermal stability under those conditions. Here, we synthesize a lithium salt of lithium perfluoropinacolatoborate (LiFPB) comprising highly-fluorinated and borate functional groups to address the above issues. It is demonstrated that the LiFPB shows superior thermal and electrochemical stability without any HF generation under high temperatures and voltages. In addition, the LiFPB can form a protective outer-organic and inner-inorganic rich cathode electrolyte interphase on LiCoO2 (LCO) surface. Simultaneously, the FPB- anions tend to integrate into lithium ion solvation structure to form a favorable fast-ion conductive LiBxOy based solid electrolyte interphase on lithium (Li) anode. All these fantastic features of LiFPB endow LCO (1.9â mAh cm-2)/Li metal cells excellent cycling under both high voltages and temperatures (e.g., 80 % capacity retention after 260â cycles at 60 °C and 4.45â V), and even at an extremely elevated temperature of 100 °C. This work emphasizes the important role of salt anions in determining the electrochemical performance of LMBs at both high temperature and voltage conditions.
RESUMEN
To address the problems associated with Li metal anodes, a fluoride-rich solid-like electrolyte (SLE) that combines the benefits of solid-state and liquid electrolytes is presented. Its unique triflate-group-enhanced frame channels facilitate the formation of a functional inorganic-rich solid electrolyte interphase (SEI), which not only improves the reversibility and interfacial charge transfer of Li anodes but also ensures uniform and compact Li deposition. Furthermore, these triflate groups contribute to the decoupling of Li+ and provide hopping sites for rapid Li+ transport, enabling a high room-temperature ionic conductivity of 1.1 mS cm-1 and a low activation energy of 0.17 eV, making it comparable to conventional liquid electrolytes. Consequently, Li symmetric cells using such SLE achieve extremely stable plating/stripping cycling over 3500 h at 0.5 mA cm-2 and support a high critical current up to 2 mA cm-2. The assembled Li||LiFePO4 solid-like batteries exhibit exceptional cyclability for over 1 year and a half, even outperforming liquid cells. Additionally, high-voltage cylindrical cells and high-capacity pouch cells are demonstrated, corroborating much simpler processibility in battery assembly compared to all-solid-state batteries.
RESUMEN
Lithium metal batteries (LMBs) employing high-voltage nickel-rich cathodes represent a promising strategy to enable higher energy density storage systems. However, instability at the electrolyte-electrode interfaces (EEIs) currently impedes the translation of these advanced systems into practical applications. Herein, 1,3-dimethyl-1H-imidazol-2(3H)-one (DMIO), integrating structural features of vinylene carbonate (VC) while substituting oxygen with electron-donating nitrogen, has been synthesized and validated as a multifunctional electrolyte additive for high-voltage LMBs. Theoretical calculations and experimental results demonstrate that the potent electron-donating nitrogen in DMIO enables preferential DMIO oxidation at the cathode while preserving its carbon-carbon double bond for a concomitant reduction on the anode. Thereby, robust DMIO-derived EEIs are generated, reinforcing cycling in the full cells. Additionally, DMIO leverages Lewis acid-based interactions to coordinate and sequester protons from acidic LiPF6 decomposition byproducts, concurrently retarding LiPF6 hydrolysis while attenuating parasitic consumption of EEIs by acidic species. Consequently, incorporating DMIO into conventional carbonate electrolytes enables an improved capacity retention of Li||NCM622 cells to 81% versus 26% in the baseline electrolyte after 600 cycles. Similarly, DMIO improves Li anode cycling performance, displaying extended life spans over 200 h in Li||Li symmetric cells and enhancing Coulombic efficiency from 76% to 88% in Li||Cu cells. The synergistic effects of DMIO on both the cathode and anode lead to substantially improved cell lifetime. This rationally designed, multifunctional electrolyte additive paradigm provides vital insights that can be translatable to further electrolyte molecular engineering strategies.
RESUMEN
Owing to the limited electrochemical stability window of carbonate electrolytes, the initial formation of a solid electrolyte interphase and surface film on the negative and positive electrode surfaces by the decomposition of the electrolyte component is inevitable for the operation of lithium secondary batteries. The deposited film on the surface of the active material is vital for reducing further electrochemical side reactions at the surface; hence, the manipulation of this formation process is necessary for the appropriate operation of the assembled battery system. In this study, the thermal decomposition of LiPF6 salt is used as a surface passivation agent, which is autocatalytically formed during high-temperature storage. The thermally formed difluorophosphoric acid is subsequently oxidized on the partially charged high-Ni positive electrode surface, which improves the cycleability of lithium metal cells via phosphorus- and fluorine-based surface film formation. Moreover, the improvement in the high-temperature cycleability is demonstrated by controlling the formation process in the lithium-ion pouch cell with a short period of high-temperature storage before battery usage.
RESUMEN
Lithium metal batteries (LMBs) with nickel-rich cathodes are promising candidates for next-generation high-energy-density batteries, but the lack of sufficiently protective electrode/electrolyte interphases (EEIs) limits their cyclability. Herein, trifluoromethoxybenzene is proposed as a cosolvent for locally concentrated ionic liquid electrolytes (LCILEs) to reinforce the EEIs. With a comparative study of a neat ionic liquid electrolyte (ILE) and three LCILEs employing fluorobenzene, trifluoromethylbenzene, or trifluoromethoxybenzene as cosolvents, it is revealed that the fluorinated groups tethered to the benzene ring of the cosolvents not only affect the electrolytes' ionic conductivity and fluidity, but also the EEIs' composition via adjusting the contribution of the 1-ethyl-3-methylimidazolium cation (Emim+ ) and bis(fluorosulfonyl)imide anion. Trifluoromethoxybenzene, as the optimal cosolvent, leads to a stable cycling of LMBs employing 5 mAh cm-2 lithium metal anodes (LMAs), 21 mg cm-2 LiNi0.8 Co0.15 Al0.05 (NCA) cathodes, and 4.2 µL mAh-1 electrolytes for 150 cycles with a remarkable capacity retention of 71%, thanks to a solid electrolyte interphase rich in inorganic species on LMAs and, particularly, a uniform cathode/electrolyte interphase rich in Emim+ -derived species on NCA cathodes. By contrast, the capacity retention under the same condition is only 16%, 46%, and 18% for the neat ILE and the LCILEs based on fluorobenzene and benzotrifluoride, respectively.
RESUMEN
Electrolyte engineering is a fascinating choice to improve the performance of Li-rich layered oxide cathodes (LRLO) for high-energy lithium-ion batteries. However, many existing electrolyte designs and adjustment principles tend to overlook the unique challenges posed by LRLO, particularly the nucleophilic attack. Here, we introduce an electrolyte modification by locally replacing carbonate solvents in traditional electrolytes with a fluoro-ether. By benefit of the decomposition of fluoro-ether under nucleophilic O-related attacks, which delivers an excellent passivation layer with LiF and polymers, possessing rigidity and flexibility on the LRLO surface. More importantly, the fluoro-ether acts as "sutures", ensuring the integrity and stability of both interfacial and bulk structures, which contributed to suppressing severe polarization and enhancing the cycling capacity retention from 39 % to 78 % after 300â cycles for the 4.8â V-class LRLO. This key electrolyte strategy with comprehensive analysis, provides new insights into addressing nucleophilic challenge for high-energy anionic redox related cathode systems.