RESUMEN

Twin-screw wet granulation (TWSG) is a promising continuous alternative of pharmaceutical wet granulation. One of its benefits is that the components dissolved in the granulation liquid are distributed homogeneously in the granules. This provides an elegant way to manufacture products with ultralow drug doses. Near-infrared (NIR) and Raman spectroscopy are well-established process analytical technology (PAT) tools that can be used for the in-line monitoring of TSWG. However, their detection limit does not enable the measurement of components in the ultralow (i.e., ppm) range. In this paper, an indirect approach is presented that enables the real-time determination of the concentration of a drug in concentrations between 40 and 100 ppm by using the signal of an excipient, in this case, the polyvinylpyrrolidone (PVP). This component is also dissolved in the granulation liquid; therefore, it is distributed in the same way as the active ingredient. Results of HPLC measurements have proved that the models trained to quantify the concentration of PVP in real-time gave an accurate determination for the active ingredient as well (root mean squared error was 7.07 ppm for Raman and 5.31 ppm for NIR spectroscopy, respectively). These findings imply that it is possible to indirectly predict the concentration of ultralow dose drugs with in-line analytical techniques based on the concentration of an excipient.

Asunto(s)

RESUMEN

The dataset consists of FTIR spectra of ultra-filtered spent sulphite liquor (UF-SSL) from softwood pulping obtained from one paper mill biorefinery plant with the purpose of real-time quantification of the sugar content of UF-SSL. Data collection was performed using a submerged mid-IR probe placed in a continuously stirred tank reactor and reference sugar measurements were performed using HPLC. Spectra were obtained of raw and spiked UF-SSL. As "low complexity" case 25% UF-SSL from one batch was analysed for its 3 most abundant sugars (mannose, xylose, glucose) and as "high complexity" case 25/50/75% UF-SSL from 2 batches was analysed for its 5 most abundant sugars (the latter + galactose, arabinose). In both cases, independent single sugar spikes and simultaneous multiple sugar spikes were performed. Real time in-line data was generated by stepwise and gradual changes in sugar composition over time with a run time of >200 h.

RESUMEN

The main purpose of this research was to develop an experimental film flow cleaning rig that can be combined with Process analytical technology (PAT) tools to reduce cleaning time and costs. Here, we show that the use of in-line UV-Vis was successful for real-time monitoring of the cleaning process of olanzapine as a challenging residue to clean. The cleaning process was found to be affected by the properties of the olanzapine soil, and the study showed the competing effects of mechanical lift-off and dissolution action with methanol as a solvent. However, The method is limited by the cleaning mechanisms, with the dissolution being the only mechanism that can be accurately quantified using an in-line UV-Vis PAT tool. This experimental approach can be used to optimize cleaning process conditions and solvent choices at the bench scale before deployment. The material of which the cleaning rig was printed limited the solvent that could be used for this study, and future modifications will include a more chemical-resistant material.

RESUMEN

A scanning acoustic microscopy (SAM) system is a common non-destructive instrument which is used to evaluate the material quality in scientific and industrial applications. Technically, the tested sample is immersed in water during the scanning process. Therefore, a robot arm is incorporated into the SAM system to transfer the sample for in-line inspection, which makes the system complex and increases time consumption. The main aim of this study is to develop a novel water probe for the SAM system, that is, a waterstream. During the scanning process, water was supplied using a waterstream instead of immersing the sample in the water, which leads to a simple design of an automotive SAM system and a reduction in time consumption. In addition, using a waterstream in the SAM system can avoid contamination of the sample due to immersion in water for long-time scanning. Waterstream was designed based on the measured focal length calculation of the transducer and simulated to investigate the internal flow characteristics. To validate the simulation results, the waterstream was prototyped and applied to the TSAM-400 and W-FSAM traditional and fast SAM systems to successfully image some samples such as carbon fiber-reinforced polymers, a printed circuit board, and a 6-inch wafer. These results demonstrate the design method of the water probe applied to the SAM system.

RESUMEN

OBJECTIVE: This study aimed to determine the impact of infrapopliteal (IP) revascularisation establishing in line flow to the wound (IFW) on wound healing in chronic limb threatening ischaemia (CLTI), using a core laboratory assessment for wounds and in line flow. METHODS: The Wound directed Angiosome RevasculaRIsation apprOach to patients with cRitical limb iSchaemia (WARRIORS) multicentre observational study enrolled patients with CLTI with tissue loss undergoing IP revascularisation in Japan, with scheduled two year follow up. The primary outcome measure was complete wound healing, defined as achievement of complete epithelialisation of all wounds without major amputation. IP revascularisation establishing IFW was defined as revascularisation after which a tibiopedal artery that actually fed an injured pedal unit was patent. The incidence of wound healing was compared between the IFW and non-IFW groups using inverse probability of treatment weighting based on the propensity score. RESULTS: A total of 440 patients with CLTI (median age, 75 years; male, 64.1%; diabetes mellitus, 72.0%; dialysis, 57.7%) with tissue loss (Wound, Ischaemia, and foot Infection stage 4, 66.4%) who underwent IP revascularisation (endovascular procedure, n = 304; bypass grafting, n = 136) between October 2017 and June 2020 were registered. During a median follow up of 23.6 months, 51.1% achieved wound healing. Successful IP revascularisation with IFW was achieved in 68.2%. After analysis, the IFW group had a higher rate of wound healing than the non-IFW group (34.5 vs. 16.1 per 100 person years; p = .030). The association between IFW and wound healing was not statistically different between patients undergoing bypass grafting and those undergoing an endovascular procedure (p for interaction = .38). There was no statistically significant interaction effect between IFW and direct revascularisation for wound healing (p for interaction = .51). CONCLUSION: IP revascularisation establishing IFW was statistically significantly associated with a higher wound healing rate in patients with CLTI.

RESUMEN

Minimizing the use of antimicrobials at the end of lactation (dry cow therapy, DCT) requires categorization of cows as likely infected or uninfected. While microbiology is the gold standard for such categorization, the costs of doing so mean that indirect tests such as somatic cell count (SCC) are commonly used. An in-line SCC sensor (SenseHub In Line Somatic Cell Count, in-line SCC) is commercially available but its utility to differentiate cows eligible for dry cow therapy has not been assessed. This prospective diagnostic accuracy study was undertaken to define the sensitivity (Se) and specificity (Sp) of SenseHub SCC against cow-composite milk samples submitted for conventional microbiology. A secondary objective was to assess the utility of SenseHub SCC compared with the maximum (max DHI SCC) or last (last DHI SCC) SCC determined from cow-composite milk samples collected as part of routine herd production recording at monthly intervals throughout lactation. Cows (n = 1,544) from 4 spring-calving, predominantly pasture-fed dairy herds from 3 regions of New Zealand had cow-composite milk samples collected following aseptic teat end preparation immediately before or after the final milking of lactation. These samples were submitted for routine microbiology. The microbiology data from approximately half the cows (n = 770; training data set) were randomly selected after blocking for intramammary infection (IMI) status within herd and these data were used to determine the optimal predictor for indicating IMI from the in-line SCC data by maximizing the area under the receiver operator curve (AUC). The average of the in-line SCC over the final 12 weeks of lactation (in-line 12wSCC) was found to be the best predictor and used for further analyses. The Se and Sp of the in-line SCC for any IMI or for a major pathogen IMI (defined as presence of Staphylococcus aureus, Streptococcus dysgalactiae or Streptococcus uberis) was calculated using the test data set (n = 774). The AUC for the maximum and last DHI SCC were compared with that of the in-line 12wSCC. The cow-level prevalence of any IMI or a major IMI across the entire population was 50.6% and 14.2%, respectively. At a cutpoint of 150,000 cells/mL, Se and Sp of the in-line 12wSCC for any IMI was 0.68 (95%CI 0.64-0.72) and 0.71 (95% CI 0.65-76), respectively, and the Se and Sp for a major pathogen IMI was 0.89 (95%CI 0.82-0.95) and 0.51 (95% CI 0.47-0.55), respectively. The AUC for a major pathogen IMI was 0.82 (95% CI 0.79-0.86), 0.82 (95% CI 0.78-0.86) and 0.84 (95% CI 0.90-0.97) for in-line 12wSCC, max DHI SCC and last DHI SCC, respectively. These AUC did not differ and the AUC for the in-line 12wSCC was non-inferior to that of the last and maximum HT SCC (both P < 0.001). It was concluded that the in-line 12wSCC had an AUC, Se and Sp not different from DHI SCC data and hence this test has utility in selecting cows for different dry cow therapy treatments.

RESUMEN

Anhydrous milk fat (AMF) and its fractions are used as ingredients in a wide range of food applications. Obtaining the appropriate solid fat content (SFC) is essential to achieve the desired product texture. At present, in-line monitoring techniques to control milk fat crystallization and melting are largely unavailable. The thermal behaviour of milk fat (AMF and four of its fractions) was monitored in a temperature-controlled vessel using an in-line Raman analyser and compared with thermograms generated using differential scanning calorimetry (DSC). The major stages of milk fat crystallization and melting were identified using the in-line Raman analyser. Thermal data from DSC showed excellent linear correlations with Raman spectral data (R2 value of 0.97 for the onset of milk fat crystallisation). Partial least squares regression (PLSR) models were developed using Raman spectra to predict SFC with coefficient of determination (R2Cs) from 0.929 to 0.992 and root mean standard error of calibration (RMSECs) ranging from 3.20 to 10.36%. Results demonstrated Raman spectroscopy has significant potential as a way of monitoring milk fat crystallization and melting processes.

Asunto(s)

RESUMEN

Therapeutic monoclonal antibodies (mAbs) are critical for treatment of a wide range of diseases. Immunoglobulin G (IgG) is the most predominant form of mAb but is prone to aggregation during production. Detection and removal of IgG aggregates are time-consuming and laborious. Chromatography is central for purification of biopharmaceuticals in general and essential in the production of mAbs. Protein purification systems are usually equipped with detectors for monitoring pH, UV absorbance, and conductivity, to facilitate optimization and control of the purification process. However, specific in-line detection of the target products and contaminating species, such as aggregates, is currently not possible using convectional techniques. Here we show a novel fiber optical in-line sensor, based on localized surface plasmon resonance (LSPR), for specific detection of IgG and IgG aggregates during affinity chromatography. A flow cell with a Protein A sensor chip was connected to the outlet of the affinity column connected to three different chromatography systems operating at lab scale to pilot scale. Samples containing various IgG concentrations and aggregate contents were analyzed in-line during purification on a Protein A column using both pH gradient and isocratic elution. Because of avidity effects, IgG aggregates showed slower dissociation kinetics than monomers after binding to the sensor chips. Possibilities to detect aggregate concentrations below 1 % and difference in aggregate content smaller than 0.3 % between samples were demonstrated. In-line detection of aggregates can circumvent time-consuming off-line analysis and facilitate automation and process intensification.

Asunto(s)

RESUMEN

A new configuration for near-field ptychography using a full-field illumination with a structured electron beam is proposed. A structured electron beam illuminating the entire field of view is scanned over the specimen, and a series of in-line holograms formed in the near-field region below the specimen are collected. The structured beam is generated by a conductive film with random openings, which ensures high stability and coherence of the beam. Observation in the near-field region reduces the beam concentration that occurs in the far-field region, which contributes to accurate recording of the beam intensity with a finite dynamic range of the detectors. The use of full-field illumination prevents the accumulation of errors caused by concatenating the local structures, which is the method used in conventional reconstruction. Since all holograms are obtained from the entire field of view, they have uniform multiplicity in terms of specimen information within the field of view. This contributes to robust and efficient reconstruction for a large field of view. The proposed method was tested using both simulated and experimental holograms. For the simulated holograms, the reconstruction of the specimen transmission function was achieved with an error less than 1/3485 of the wavelength. The method was further validated using experimental holograms obtained from MgO particles. The reconstructed phase transmission function of the specimen was consistent with the specimen structure and was equivalent to a mean inner potential of V on the MgO particle, which is in close agreement with previously reported values.

RESUMEN

Wastewater reuse is one of the crucial water resources in Egypt due to the ongoing need to increase water resources and close the supply-demand gap. In this study, a new coagulant has been investigated before sand filters as an advanced wastewater treatment method. The sand filter pilot was run at a hydraulic loading rate of 0.75 m/h and two different dosages of three coagulants (Alum, FeCl3, and Ferrate VI) were selected using the jar tests. The sand filter without coagulant removed 12% of BOD5 and 70% of turbidity. Applying in-line coagulation before the sand filter provided effluents with better quality, especially for turbidity, organics, and microorganisms. Ferrate provided the highest removal of turbidity (90%) and BOD5 (93%) at very low dosages and lower costs compared with other coagulants, however, it adversely impacted both conductivity and dissolved solids. A significant effect on reducing bacteria was obtained with 40.0 mg/L of alum. According to the study's findings, the ferrate coagulant enhanced the sand filter's performance producing effluents with high quality, enabling it to meet strict water reuse regulations as well as aquatic environmental and health preservations.

Asunto(s)

RESUMEN

Untreated polyester films and fibers can be hardly printed or coated, in particular if aqueous inks or lacquers have to be applied. Therefore, an adequate primer layer has to be applied first. A cationic polymer formulation based on poly(dimethylamine-co-epichlorohydrin-co-ethylenediamine) (PDEHED) was used as primer layer for digital printing on polyester fabrics. Because of the exceedingly high requirements on the homogeneity of such layers, hyperspectral imaging was used for qualitative and quantitative monitoring of the distribution of the primer layer on the textiles. Multivariate data analysis methods based on the PLS algorithm were applied for quantification of the NIR reflection spectra using gravimetry as a reference method. Optimization of the calibration method resulted in various models with prediction errors of about 1.2 g/m2. The prediction performance of the models was proven in external validations using independent samples. Moreover, a special ink jet printing technology was tested for application of the aqueous primer formulation itself. Since possible clogging of jet nozzles in the print head might lead to inhomogeneity in the coatings such as missing tracks, the potential of hyperspectral imaging to detect such defects was investigated. It was demonstrated that simulated missing tracks can be clearly detected. Consequently, hyperspectral imaging has been proven to be a powerful analytical tool for in-line monitoring of the quality of printability improvement layers and similar systems.

RESUMEN

Significance: In in-line digital holographic microscopy (DHM), twin-image artifacts pose a significant challenge, and reduction or complete elimination is essential for object reconstruction. Aim: To facilitate object reconstruction using a single hologram, significantly reduce inaccuracies, and avoid iterative processing, a digital holographic reconstruction algorithm called phase-support constraint on phase-only function (PCOF) is presented. Approach: In-line DHM simulations and tabletop experiments employing the sliding-window approach are used to compute the arithmetic mean and variance of the phase values in the reconstructed image. A support constraint mask, through variance thresholding, effectively enabled twin-image artifacts. Results: Quantitative evaluations using metrics such as mean squared error, peak signal-to-noise ratio, and mean structural similarity index show PCOF's superior capability in eliminating twin-image artifacts and achieving high-fidelity reconstructions compared with conventional methods such as angular spectrum and iterative phase retrieval methods. Conclusions: PCOF stands as a promising approach to in-line digital holographic reconstruction, offering a robust solution to mitigate twin-image artifacts and enhance the fidelity of reconstructed objects.

Asunto(s)

RESUMEN

DNA methylation is an important epigenetic modification that regulates chromatin structure and the cell-type-specific expression of genes. The association of aberrant DNA methylation with many diseases, as well as the increasing interest in modifying the methylation mark in a directed manner at genomic sites using epigenome editing for research and therapeutic purposes, increases the need for easy and efficient DNA methylation analysis methods. The standard approach to analyze DNA methylation with a single-cytosine resolution is bisulfite conversion of DNA followed by next-generation sequencing (NGS). In this chapter, we describe a robust, powerful, and cost-efficient protocol for the amplification of target regions from bisulfite-converted DNA, followed by a second PCR step to generate libraries for Illumina NGS. In the two consecutive PCR steps, first, barcodes are added to individual amplicons, and in the second PCR, indices and Illumina adapters are added to the samples. Finally, we describe a detailed bioinformatics approach to extract DNA methylation levels of the target regions from the sequencing data. Combining barcodes with indices enables a high level of multiplexing allowing to sequence multiple pooled samples in the same sequencing run. Therefore, this method is a robust, accurate, quantitative, and cheap approach for the readout of DNA methylation patterns at defined genomic regions.

Asunto(s)

RESUMEN

Permanent engravings on contact lenses provide information about the manufacturing process and lens positioning when they are placed on the eye. The inspection of their morphological characteristics is important, since they can affect the user's comfort and deposit adhesion. Therefore, an inverted wavefront holoscope (a lensless microscope based on Gabor's principle of in-line digital holography) is explored for the characterization of the permanent marks of soft contact lenses. The device, based on an in-line transmission configuration, uses a partially coherent laser source to illuminate the soft contact lens placed in a cuvette filled with a saline solution for lens preservation. Holograms were recorded on a digital sensor and reconstructed by back propagation to the image plane based on the angular spectrum method. In addition, a phase-retrieval algorithm was used to enhance the quality of the recovered images. The instrument was experimentally validated through a calibration process in terms of spatial resolution and thickness estimation, showing values that perfectly agree with those that were theoretically expected. Finally, phase maps of different engravings for three commercial soft contact lenses were successfully reconstructed, validating the inverted wavefront holoscope as a potential instrument for the characterization of the permanent marks of soft contact lenses. To improve the final image quality of reconstructions, the geometry of lenses should be considered to avoid induced aberration effects.

RESUMEN

Digital in-line holographic microscopy (DIHM) is a non-invasive, real-time, label-free technique that captures three-dimensional (3D) positional, orientational, and morphological information from digital holographic images of living biological cells. Unlike conventional microscopies, the DIHM technique enables precise measurements of dynamic behaviors exhibited by living cells within a 3D volume. This review outlines the fundamental principles and comprehensive digital image processing procedures employed in DIHM-based cell tracking methods. In addition, recent applications of DIHM technique for label-free identification and digital tracking of various motile biological cells, including human blood cells, spermatozoa, diseased cells, and unicellular microorganisms, are thoroughly examined. Leveraging artificial intelligence has significantly enhanced both the speed and accuracy of digital image processing for cell tracking and identification. The quantitative data on cell morphology and dynamics captured by DIHM can effectively elucidate the underlying mechanisms governing various microbial behaviors and contribute to the accumulation of diagnostic databases and the development of clinical treatments.

Asunto(s)

RESUMEN

BACKGROUND: X-ray imaging is widely used for the non-destructive detection of defects in industrial products on a conveyor belt. In-line detection requires highly accurate, robust, and fast algorithms. Deep Convolutional Neural Networks (DCNNs) satisfy these requirements when a large amount of labeled data is available. To overcome the challenge of collecting these data, different methods of X-ray image generation are considered. OBJECTIVE: Depending on the desired degree of similarity to real data, different physical effects should either be simulated or can be ignored. X-ray scattering is known to be computationally expensive to simulate, and this effect can greatly affect the accuracy of a generated X-ray image. We aim to quantitatively evaluate the effect of scattering on defect detection. METHODS: Monte-Carlo simulation is used to generate X-ray scattering distribution. DCNNs are trained on the data with and without scattering and applied to the same test datasets. Probability of Detection (POD) curves are computed to compare their performance, characterized by the size of the smallest detectable defect. RESULTS: We apply the methodology to a model problem of defect detection in cylinders. When trained on data without scattering, DCNNs reliably detect defects larger than 1.3 mm, and using data with scattering improves performance by less than 5%. If the analysis is performed on the cases with large scattering-to-primary ratio (1 < SPR < 5), the difference in performance could reach 15% (approx. 0.4 mm). CONCLUSION: Excluding the scattering signal from the training data has the largest effect on the smallest detectable defects, and the difference decreases for larger defects. The scattering-to-primary ratio has a significant effect on detection performance and the required accuracy of data generation.

Asunto(s)

RESUMEN

The global reliance on oil and gas pipelines for energy transportation is increasing. As the pioneering review in the field of ultrasonic defect detection for oil and gas pipelines based on bibliometric methods, this study employs visual analysis to identify the most influential countries, academic institutions, and journals in this domain. Through cluster analysis, it determines the primary trends, research hotspots, and future directions in this critical field. Starting from the current global industrial ultrasonic in-line inspection (ILI) detection level, this paper provides a flowchart for selecting detection methods and a table for defect comparison, detailing the comparative performance limits of different detection devices. It offers a comprehensive perspective on the latest ultrasonic pipeline detection technology from laboratory experiments to industrial practice.

RESUMEN

Microscopic defects in flip chips, originating from manufacturing, significantly affect performance and longevity. Post-fabrication sampling methods ensure product functionality but lack in-line defect monitoring to enhance chip yield and lifespan in real-time. This study introduces a photoacoustic remote sensing (PARS) system for in-line imaging and defect recognition during flip-chip fabrication. We first propose a real-time PARS imaging method based on continuous acquisition combined with parallel processing image reconstruction to achieve real-time imaging during the scanning of flip-chip samples, reducing reconstruction time from an average of approximately 1134 ms to 38 ms. Subsequently, we propose improved YOLOv7 with space-to-depth block (IYOLOv7-SPD), an enhanced deep learning defect recognition method, for accurate in-line recognition and localization of microscopic defects during the PARS real-time imaging process. The experimental results validate the viability of the proposed system for enhancing the lifespan and yield of flip-chip products in chip manufacturing facilities.

RESUMEN

Seeing the atomic configuration of single organic nanoparticles at a sub-Å spatial resolution by transmission electron microscopy has been so far prevented by the high sensitivity of soft matter to radiation damage. This difficulty is related to the need to irradiate the particle with a total dose of a few electrons/Å2, not compatible with the electron beam density necessary to search the low-contrast nanoparticle, to control its drift, finely adjust the electron-optical conditions and particle orientation, and finally acquire an effective atomic-resolution image. On the other hand, the capability to study individual pristine nanoparticles, such as proteins, active pharmaceutical ingredients, and polymers, with peculiar sensitivity to the variation in the local structure, defects, and strain, would provide advancements in many fields, including materials science, medicine, biology, and pharmacology. Here, we report the direct sub-ångström-resolution imaging at room temperature of pristine unstained crystalline polymer-based nanoparticles. This result is obtained by combining low-dose in-line electron holography and phase-contrast imaging on state-of-the-art equipment, providing an effective tool for the quantitative sub-ångström imaging of soft matter.

RESUMEN

Patients in intensive care are exposed to the risk of microparticle infusion via extracorporeal lines and the resulting complications. A possible source of microparticle release could be the extracorporeal circuit used in blood purification techniques, such as continuous renal replacement therapy (CRRT). Disposable components of CRRT circuits, such as replacement bags and circuit tubing, might release microparticles such as salt crystals produced by precipitation in replacement bags and plastic microparticles produced by spallation. In-line filtration has proven effective in retaining microparticles both in in-vitro and in-vivo studies. In our study, we performed an in-vitro model of CRRT-treatment with the aim of detecting the microparticles produced and released into the circuit by means of a qualitative and quantitative analysis, after sampling the replacement and patient lines straddling a series of in-line filters. Working pressures and flows were monitored during the experiment. This study showed that microparticles are indeed produced and released into the CRRT circuit. The inclusion of in-line filters in the replacement lines allows to reduce the burden of microparticles infused into the bloodstream during extracorporeal treatments, reducing the concentration of microparticles from 14 mg/mL pre in-line filter to 11 mg/mL post in-line filter. Particle infusion and related damage must be counted among the pathophysiological mechanisms supporting iatrogenic damage due to artificial cross-talk between organs during CRRT applied to critically ill patients. This damage can be reduced by using in-line filters in the extracorporeal circuit.

Asunto(s)