RESUMEN

The selection of an appropriate transducer is a key element in biosensor development. Currently, a wide variety of substrates and working electrode materials utilizing different fabrication techniques are used in the field of biosensors. In the frame of this study, the following three specific material configurations with gold-finish layers were investigated regarding their efficacy to be used as electrochemical (EC) biosensors: (I) a silicone-based sensor substrate with a layer configuration of 50 nm SiO/50 nm SiN/100 nm Au/30-50 nm WTi/140 nm SiO/bulk Si); (II) polyethylene naphthalate (PEN) with a gold inkjet-printed layer; and (III) polyethylene terephthalate (PET) with a screen-printed gold layer. Electrodes were characterized using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) to evaluate their performance as electrochemical transducers in an aptamer-based biosensor for the detection of cardiac troponin I using the redox molecule hexacyanoferrade/hexacyaniferrade (K3[Fe (CN)6]/K4[Fe (CN)6]. Baseline signals were obtained from clean electrodes after a specific cleaning procedure and after functionalization with the thiolate cardiac troponin I aptamers "Tro4" and "Tro6". With the goal of improving the PEN-based and PET-based performance, sintered PEN-based samples and PET-based samples with a carbon or silver layer under the gold were studied. The effect of a high number of immobilized aptamers will be tested in further work using the PEN-based sample. In this study, the charge-transfer resistance (Rct), anodic peak height (Ipa), cathodic peak height (Ipc) and peak separation (∆E) were determined. The PEN-based electrodes demonstrated better biosensor properties such as lower initial Rct values, a greater change in Rct after the immobilization of the Tro4 aptamer on its surface, higher Ipc and Ipa values and lower ∆E, which correlated with a higher number of immobilized aptamers compared with the other two types of samples functionalized using the same procedure.

Asunto(s)

RESUMEN

This study introduces an innovative electrochemical aptasensor designed for the highly sensitive and rapid detection of Legionella pneumophila serogroup 1 (L. pneumophila SG1), a particularly virulent strain associated with Legionellosis. Employing a rigorous selection process utilizing cell-based systematic evolution of ligands by exponential enrichment (cell-SELEX), we identified new high-affinity aptamers specifically tailored for L. pneumophila SG1. The selection process encompassed ten rounds of cell-SELEX cycles with live L. pneumophila, including multiple counter-selection steps against the closely related Legionella sub-species. The dissociation constant (Kd) of the highest affinity sequence to L. pneumophila SG1 was measured at 14.2 nM, representing a ten-fold increase in affinity in comparison with the previously reported aptamers. For the development of electrochemical aptasensor, a gold electrode was modified with the selected aptamer through the formation of self-assembled monolayers (SAMs). The newly developed aptasensor exhibited exceptional sensitivity, and specificity in detecting and differentiating various Legionella sp., with a detection limit of 5 colony forming units (CFU)/mL and an insignificant/negligible cross-reactivity with closely related sub-species. Furthermore, the aptasensor effectively detected L. pneumophila SG1 in spiked water samples, demonstrating an appreciable recovery percentage. This study shows the potential of our aptamer-based electrochemical biosensor as a promising approach for detecting L. pneumophila SG1 in diverse environments.

Asunto(s)

RESUMEN

Food contamination by aflatoxins is an urgent global issue due to its high level of toxicity and the difficulties in limiting the diffusion. Unfortunately, current detection techniques, which mainly use biosensing, prevent the pervasive monitoring of aflatoxins throughout the agri-food chain. In this work, we investigate, through ab initio atomistic calculations, a pyrrole-based Molecular Field Effect Transistor (MolFET) as a single-molecule sensor for the amperometric detection of aflatoxins. In particular, we theoretically explain the gate-tuned current modulation from a chemical-physical perspective, and we support our insights through simulations. In addition, this work demonstrates that, for the case under consideration, the use of a suitable gate voltage permits a considerable enhancement in the sensor performance. The gating effect raises the current modulation due to aflatoxin from 100% to more than 103÷104%. In particular, the current is diminished by two orders of magnitude from the µA range to the nA range due to the presence of aflatoxin B1. Our work motivates future research efforts in miniaturized FET electrical detection for future pervasive electrical measurement of aflatoxins.

Asunto(s)

RESUMEN

Recent developments in embedded electronics require the development of micro sources of energy. In this paper, the fabrication of an on-chip interdigitated all-solid-state supercapacitor, using porous gold electrodes and a PVA/KOH quasisolid electrolyte, is demonstrated. The fabrication of the interdigitated porous gold electrode is performed using an original bottom-up approach. A templating method is used for porosity, using a wet chemistry process followed by microfabrication techniques. This paper reports the first example of an all-gold electrode micro-supercapacitor. The supercapacitor exhibits a specific capacitance equal to 0.28 mF·cm-2 and a specific energy of 0.14 mJ·cm-2. The capacitance value remains stable up to more than 8000 cycles.

Asunto(s)

RESUMEN

Flexible and implantable electronics hold tremendous promises for advanced healthcare applications, especially for physiological neural recording and modulations. Key requirements in neural interfaces include miniature dimensions for spatial physiological mapping and low impedance for recognizing small biopotential signals. Herein, a bottom-up mesoporous formation technique and a top-down microlithography process are integrated to create flexible and low-impedance mesoporous gold (Au) electrodes for biosensing and bioimplant applications. The mesoporous architectures developed on a thin and soft polymeric substrate provide excellent mechanical flexibility and stable electrical characteristics capable of sustaining multiple bending cycles. The large surface areas formed within the mesoporous network allow for high current density transfer in standard electrolytes, highly suitable for biological sensing applications as demonstrated in glucose sensors with an excellent detection limit of 1.95 µm and high sensitivity of 6.1 mA cm-2  µM-1 , which is approximately six times higher than that of benchmarking flat/non-porous films. The low impedance of less than 1 kΩ at 1 kHz in the as-synthesized mesoporous electrodes, along with their mechanical flexibility and durability, offer peripheral nerve recording functionalities that are successfully demonstrated in vivo. These features highlight the new possibilities of our novel flexible nanoarchitectonics for neuronal recording and modulation applications.

Asunto(s)

RESUMEN

In this study, a simple one-stage laser-assisted metallization technique based on laser-induced backside wet etching and laser-induced chemical liquid-phase deposition is proposed. It allows for the fabrication of gold micropatterns inside the laser-written trace on a glass substrate. The reduction and deposition of gold inside and outside the laser-ablated channel were confirmed. The presence of Au nanoparticles on the surface of the laser-written micropattern is revealed by atomic force microscopy. The specific resistivity of the gold trace formed by ultrafast light-assisted metal micropatterning on a dielectric glass substrate is estimated as 0.04 ± 0.02 mΩ·cm. The obtained results empower the method of the selective laser-assisted deposition of metals on dielectrics and are of interest for the development of microelectronic components and catalysts, heaters, and sensors for lab-on-a-chip devices.

RESUMEN

This paper described an impedimetric immunosensor for detecting Plasmodium falciparum histidine-rich protein 2 (PfHRP2). Antibodies from egg yolk (Ab-PfHRP2, IgY type) were linked covalently to the screen-printed gold electrodes (SPGE) surface modified with a thin film of Poly-pyrrole-pyrrole 3 carboxylic acid (P(Py-Py3COOH) to develop the sensing platform. The fabrication steps were followed by microscopic (scanning electron microscopy), spectroscopic (RAMAN spectroscopy and Energy-dispersive X-ray spectroscopy), and electrochemical (electrochemical impedance spectroscopy (EIS) and cyclic voltammetry) techniques. The determination of Ag-PfHRP2 was performed by EIS, and the BSA(bovine serum albumin)/Ab-PfHRP2(IgY)/P(Py-Py3COOH)/SPGE immunosensor recorded a linear response at 100-1000 ng mL-1 concentration range, with a limit of detection (LOD) of 27.47 ng mL-1. Its performance was confirmed by Enzyme-Linked Immuno-Sorbent Assay. The fabricated device uses a simple strategy of IgY immobilization, showing high sensitivity and good selectivity, and can be considered an alternative for carrying out malaria tests.

Asunto(s)

RESUMEN

The adsorption of analyte molecules on nano-optoelectrodes (e.g. a combined nanoantenna and nanoelectrode device) significantly affects the signal characteristics in surface-enhanced Raman scattering (SERS) measurements. Understanding how different molecules adsorb on electrodes and their electrical potential modulation helps interpret SERS measurements better. We use molecular dynamics simulations to investigate the adsorption of prototypical analyte molecules (rhodamine 6G and choline) on gold electrodes with negative, neutral, and positive surface charges. We show that both molecules can readily adsorb on gold surfaces at all surface charge densities studied. Nevertheless, the configurations of the adsorbed molecules can differ for different surface charge densities, and adsorption can also change a molecule's conformation. Rhodamine 6G molecules adsorb more strongly than choline molecules, and the adsorption of both molecules is affected by electrode charge in 0.25 M NaCl solutions. The mechanisms of these observations are elucidated, and their implications for voltage-modulated SERS measurements are discussed.

RESUMEN

Flexible polymer neural probes are an attractive emerging approach for invasive brain recordings, given that they can minimize the risks of brain damage or glial scaring. However, densely packed electrode sites, which can facilitate neuronal data analysis, are not widely available in flexible probes. Here, we present a new flexible polyimide neural probe, based on standard and low-cost lithography processes, which has 32 closely spaced 10 µm diameter gold electrode sites at two different depths from the probe surface arranged in a matrix, with inter-site distances of only 5 µm. The double-layer design and fabrication approach implemented also provides additional stiffening just sufficient to prevent probe buckling during brain insertion. This approach avoids typical laborious augmentation strategies used to increase flexible probes' mechanical rigidity while allowing a small brain insertion footprint. Chemical composition analysis and metrology of structural, mechanical, and electrical properties demonstrated the viability of this fabrication approach. Finally, in vivo functional assessment tests in the mouse cortex were performed as well as histological assessment of the insertion footprint, validating the biological applicability of this flexible neural probe for acquiring high quality neuronal recordings with high signal to noise ratio (SNR) and reduced acute trauma.

RESUMEN

The influence of electrolyte pH, the presence of alkali metal cations (Na+ , K+ ), and the presence of O2 on the interfacial water structure of polycrystalline gold electrodes has been experimentally studied in detail. The potential of maximum entropy (PME) was determined by the laser-induced current transient (LICT) technique. Our results demonstrate that increasing the electrolyte pH and introducing O2 shift the PME to more positive potentials. Interestingly, the PME exhibits a higher sensitivity to the pH change in the presence of K+ than Na+ . Altering the pH of the K2 SO4 solution from 4 to 6 can cause a drastic shift in the PME. These findings reveal that, for example, K2 SO4 and Na2 SO4 cannot be considered as equal supporting electrolytes: it is not a viable assumption. This can likely be extrapolated to other common "inert" supporting electrolytes. Beyond this, knowledge about the near-ideal electrolyte composition can be used to optimize electrochemical devices such as electrolyzers, fuel cells, batteries, and supercapacitors.

RESUMEN

Neuronal damage secondary to traumatic brain injury (TBI) is a rapidly evolving condition, which requires therapeutic decisions based on the timely identification of clinical deterioration. Changes in S100B biomarker levels are associated with TBI severity and patient outcome. The S100B quantification is often difficult since standard immunoassays are time-consuming, costly, and require extensive expertise. A zero-length cross-linking approach on a cysteamine self-assembled monolayer (SAM) was performed to immobilize anti-S100B monoclonal antibodies onto both planar (AuEs) and interdigitated (AuIDEs) gold electrodes via carbonyl-bond. Surface characterization was performed by atomic force microscopy (AFM) and specular-reflectance FTIR for each functionalization step. Biosensor response was studied using the change in charge-transfer resistance (Rct) from electrochemical impedance spectroscopy (EIS) in potassium ferrocyanide, with [S100B] ranging 10-1000 pg/mL. A single-frequency analysis for capacitances was also performed in AuIDEs. Full factorial designs were applied to assess biosensor sensitivity, specificity, and limit-of-detection (LOD). Higher Rct values were found with increased S100B concentration in both platforms. LODs were 18 pg/mL(AuES) and 6 pg/mL(AuIDEs). AuIDEs provide a simpler manufacturing protocol, with reduced fabrication time and possibly costs, simpler electrochemical response analysis, and could be used for single-frequency analysis for monitoring capacitance changes related to S100B levels.

RESUMEN

We identify imidazole as a pH-activated linker for forming stable single molecule-gold junctions with several distinct configurations and reproducible electrical characteristics. Using a scanning tunneling microscope break junction (STMBJ) technique, we find multiple robust conductance signatures at integer multiples of 1.9 × 10-2G0 and 1.2 × 10-4G0 and determine that this molecule bridges the electrodes in its deprotonated form through the nitrogen atoms in basic conditions only, with several molecules able to bind in parallel and in series. The elongation these junctions can sustain is longer than the length of the molecule, suggesting that plastic deformation of gold electrodes occurs during stretching. Density functional theory calculations confirm that the imidazolate-linked junctions exhibit bond strengths of ∼2 eV, which can allow for plastic extraction of gold atoms. On the basis of these results, we hypothesize that lower conductance peaks correspond to chains of repeating molecule-gold units that we form and measure in situ.

RESUMEN

The development of reliable biosensing platforms plays a key role in the detection of proteins in clinically and environmentally derived samples for diagnostics, as well as for process monitoring in biotechnological productions. For this purpose, the biosensor has to be stable and reproducible, and highly sensitive to detect potentially extremely low concentrations and prevent the nonspecific binding of interfering compounds. In this review, we present an overview of recently published (2017-2019) immobilization techniques for aptamers on gold electrodes for the electrochemical detection of proteins. These include the direct immobilization of thiolated aptamers and the utilization of short linkers, streptavidin/biotin interaction, as well as DNA nanostructures and reduced graphene oxide as immobilization platforms. Applied strategies for signal amplification and the prevention of biofouling are additionally discussed, as they play a crucial role in the design of biosensors. While a wide variety of amplification strategies are already available, future investigations should aim to establish suitable antifouling strategies that are compatible with electrochemical measurements. The focus of our review lies on the detailed discussion of the underlying principles and the presentation of utilized chemical protocols in order to provide the reader with promising ideas and profound knowledge of the subject, as well as an update on recent discoveries and achievements.

Asunto(s)

RESUMEN

A simple procedure for field fish sample pretreatment was developed. This treatment in combination with square wave anodic stripping voltammetry (SW-ASV) with solid gold electrodes (SGE) and gold nanoparticle-modified glassy carbon electrodes (AuNPs-GCE) was applied for the determination of total mercury content. A certified reference material (CRM, Tuna Fish BCR 463), ten freeze-dried samples of canned tuna and two fresh fish samples were analysed both with a bench-top voltammetric analyser after microwave digestion and with a portable potentiostat after mild eating using a small commercial food warmer. The results obtained by the two SW-ASV approaches and by a Direct Mercury Analyser (DMA), the official method for mercury determination, were in very good agreement. In particular, (i) the results obtained with in field procedure are consistent with those obtained with the conventional microwave digestion; (ii) the presence of gold nanoparticles on the active electrode surface permits an improvement of the analytical performance in comparison to the SGE: the Limit of Quantification (LOQ) for mercury in fish-matrix was 0.1 µg L-1 (Hg cell concentration), corresponding to 0.06 mg kg-1 wet fish, which is a performance comparable to that of DMA. The pretreatment proposed in this study is very easy and applicable to fresh fish; in combination with a portable potentiostat, it proved to be an interesting procedure for on-site mercury determination.

Asunto(s)

RESUMEN

Integrating microfluidics with biosensors is of great research interest with the increasing trend of lab-on-the chip and point-of-care devices. Though there have been numerous studies performed relating microfluidics to the biosensing mechanisms, the study of the sensitivity variation due to microfluidic flow is very much limited. In this paper, the sensitivity of interdigitated electrodes was evaluated at the static drop condition and the microfluidic flow condition. In addition, this study demonstrates the use of gold nanoparticles to enhance the sensor signal response and provides experimental results of the capacitance difference during cancer antigen-125 (CA-125) antigen-antibody conjugation at multiple concentrations of CA-125 antigens. The experimental results also provide evidence of disease-specific detection of CA-125 antigen at multiple concentrations with the increase in capacitive signal response proportional to the concentration of the CA-125 antigens. The capacitive signal response of antigen-antibody conjugation on interdigitate electrodes has been enhanced by approximately 2.8 times (from 260.80 to 736.33 pF at 20 kHz frequency) in static drop condition and approximately 2.5 times (from 205.85 to 518.48 pF at 20 kHz frequency) in microfluidic flow condition with gold nanoparticle-coating. The capacitive signal response is observed to decrease at microfluidic flow condition at both plain interdigitated electrodes (from 260.80 to 205.85 pF at 20 kHz frequency) and gold nano particle coated interdigitated electrodes (from 736.33 to 518.48 pF at 20 kHz frequency), due to the strong shear effect compared to static drop condition. However, the microfluidic channel in the biosensor has the potential to increase the signal to noise ratio due to plasma separation from the whole blood and lead to the increase concentration of the biomarkers in the blood volume for sensing.

RESUMEN

Electrical properties of self-assembling DNA nanostructures underlie the paradigm of nanoscale bioelectronics, and as such require clear understanding. DNA-mediated electron transfer (ET) from a gold electrode to DNA-bound Methylene Blue (MB) shows directional preference, and it is sequence-specific. During the electrocatalytic reduction of [Fe(CN)6 ]3- catalyzed by DNA-bound MB, the ET rate constant for DNA-mediated reduction of MB reaches (1.32±0.2)103 and (7.09±0.4)103  s-1 for (dGdC)20 and (dAdT)25 duplexes. The backward oxidation process is less efficient, making the DNA duplex a molecular rectifier. Lower rates of ET via (dGdC)20 agree well with its disturbed π-stacked sub-molecular structure. Such direction- and sequence-specific ET may be implicated in DNA oxidative damage and repair, and be relevant to other polarized surfaces, such as cell membranes and biomolecular interfaces.

RESUMEN

In this study, nanostructured porous gold electrodes were prepared by the anodization of gold in the presence of oxalic acid or glucose as a reductant, and applied as scaffolds for direct electron transfer (DET)-type bioelectrocatalysis. Gold cations generated in the anodization seem to be reduced by the reductant to construct a porous gold structure. The DET-type performance of the electrode was examined using two DET-type model enzymes, bilirubin oxidase (BOD) and peroxidase (POD), for the four-electron reduction of dioxygen and the two-electron reduction of peroxide, respectively. BOD and POD on the anodized porous gold electrodes exhibited well-defined sigmoidal steady-state waves corresponding to DET-type bioelectrocatalysis. Scanning electron microscopy images revealed sponge-like pores on the electrodes. The anodized porous gold electrodes demonstrate promise as scaffolds for DET-type bioelectrocatalysis.

Asunto(s)

RESUMEN

Percolation networks of one-dimensional (1D) building blocks (e.g., metallic nanowires or carbon nanotubes) represent the mainstream strategy to fabricate stretchable conductors. One of the inherent limitations is the control over junction resistance between 1D building blocks in natural and strained states of conductors. Herein, we report highly stretchable transparent strain-insensitive conductors using fractal gold (F-Au) nanoframework based on a one-pot templateless wet chemistry synthesis method. The monolayered F-Au nanoframework (∼20 nm in thickness) can be obtained from the one-pot synthesis without any purification steps involved and can be transferred directly to arbitrary substrates like polyethylene terephthalate, food-wrap, polydimethylsiloxane (PDMS), and ecoflex. The F-Au thin film with no capping agents leads to a highly conductive thin film without any post-treatment and can be stretched up to 110% strain without significantly losing conductivity yet with the optical transparency of 70% at 550 nm. Remarkably, the F-Au thin film shows the strain-insensitive behavior up to 20% stretching strain. This originates from the unique fractal nanomesh-like structure which can absorb external mechanical forces, thus maintaining electron pathways throughout the nanoframework. In addition, a semitransparent bilayered F-Au film on 100% prestrained PDMS could achieve to a high stretchability of 420% strain with negligible resistance changes under low-level strains.

RESUMEN

A conductometric sensor based on screen-printed interdigital gold electrodes on glass substrate coated with molecularly imprinted polyurethane layers was fabricated to detect polycyclic aromatic hydrocarbons (PAHs) in water. The results prove that screen-printed interdigital electrodes are very suitable transducers to fabricate low-cost sensor systems for measuring change in resistance of PAH-imprinted layers while exposing to different PAHs. The sensor showed good selectivity to its templated molecules and high sensitivity with a detection limit of 1.3 nmol/L e.g., for anthracene in water which is lower than WHO's permissible limit.

RESUMEN

N-Heterocyclic carbenes (NHCs), which react with the surface of Au electrodes, have been successfully applied in pentacene transistors. With the application of NHCs, the charge-carrier mobility of pentacene transistors increased by five times, while the contact resistance at the pentacene-Au interface was reduced by 85 %. Even after annealing the NHC-Au electrodes at 200 °C for 2 h before pentacene deposition, the charge-carrier mobility of the pentacene transistors did not decrease. The distinguished performance makes NHCs as excellent alternatives to thiols as metal modifiers for the application in organic field-effect transistors (OFETs).