RESUMEN
Releasing epitaxial perovskite oxide films from their native oxide substrates produces high quality, 2D-material-like monocrystalline freestanding oxide membranes, as potential key components for the next-generation electronic devices. Two major obstacles still limit their practical applications: macroscopic material defects (mainly cracks) that lowers uniformity and yield, and the high cost of the consumed oxide substrates. Here, a two-step film transfer method and a substrate recycling method enable repetitive fabrication of millimeter-scale, fully-connected freestanding oxide films of various chemical compositions from the same substrates; arrays of capacitor and resistor devices based on these oxides transferred on silicon indicate high uniformity, low sample-to-sample variation, and satisfactory electrical connectivity. The two-step transfer suppresses crack formation by avoiding buckling-delamination-type relaxation of epitaxial strain, and the key point to achieve substrate reuse is to remove the residual Al species bonded to the substrate surfaces. The mitigation of such long-lasting issues in freestanding oxide fabrication techniques may eventually pave roads toward future industrial-grade devices, as well as enabling many research opportunities in fundamental physics.
RESUMEN
The heterogeneous nature, local presence, and dynamic evolution of defects typically govern the ionic and electronic properties of a wide variety of functional materials. While the last 50 years have seen considerable efforts into development of new methods to identify the nature of defects in complex materials, such as the perovskite oxides, very little is known about defect dynamics and their influence on the functionality of a material. Here, the discovery of the intermittent behavior of point defects (oxygen vacancies) in oxide heterostructures employing X-ray photon correlation spectroscopy is reported. Local fluctuations between two ordered phases in strained SrCoOx with different degrees of stability of the oxygen vacancies are observed. Ab-initio-informed phase-field modeling reveals that fluctuations between the competing ordered phases are modulated by the oxygen ion/vacancy interaction energy and epitaxial strain. The results demonstrate how defect dynamics, evidenced by measurement and modeling of their temporal fluctuations, give rise to stochastic properties that now can be fully characterized using coherent X-rays, coupled for the first time to multiscale modeling in functional complex oxide heterostructures. The study and its findings open new avenues for engineering the dynamical response of functional materials used in neuromorphic and electrochemical applications.
RESUMEN
A novel in situ methodology for the direct study of mass-transport properties in oxides with spatial and unprecedented time resolution, based on Raman spectroscopy coupled to isothermal isotope exchanges, is developed. Changes in the isotope concentration, resulting in a Raman frequency shift, can be followed in real time, which is not accessible by conventional methods, enabling complementary insights for the study of ion-transport properties of electrode and electrolyte materials for advanced solid-state electrochemical devices. The proof of concept and strengths of isotope exchange Raman spectroscopy (IERS) is demonstrated by studying the oxygen isotope back-exchange in gadolinium-doped ceria (CGO) thin films. Resulting oxygen self-diffusion and surface exchange coefficients are compared to conventional time-of-flight secondary-ion mass spectrometry (ToF-SIMS) characterization and literature values, showing good agreement, while at the same time providing additional insight, challenging established assumptions. IERS captivates through its rapidity, simple setup, non-destructive nature, cost effectiveness, and versatile fields of application and thus can readily be integrated as new standard tool for in situ and operando characterization in many laboratories worldwide. The applicability of this method is expected to consolidate the understanding of elementary physicochemical processes and impact various emerging fields including solid oxide cells, battery research, and beyond.
RESUMEN
Complex oxide heterointerfaces contain a rich playground of novel physical properties and functionalities, which give rise to emerging technologies. Among designing and controlling the functional properties of complex oxide film heterostructures, vertically aligned nanostructure (VAN) films using a self-assembling bottom-up deposition method presents great promise in terms of structural flexibility and property tunability. Here, the bottom-up self-assembly is extended to a new approach using a mixture containing a 2Dlayer-by-layer film growth, followed by a 3D VAN film growth. In this work, the two-phase nanocomposite thin films are based on LaAlO3 :LaBO3 , grown on a lattice-mismatched SrTiO3001 (001) single crystal. The 2D-to-3D transient structural assembly is primarily controlled by the composition ratio, leading to the coexistence of multiple interfacial properties, 2D electron gas, and magnetic anisotropy. This approach provides multidimensional film heterostructures which enrich the emergent phenomena for multifunctional applications.
RESUMEN
In condensed matter physics, oxide materials show various intriguing physical properties. Therefore, many efforts are made in this field to develop functional oxides. Due to the excellent potential for tin-based perovskite oxides, an expansion of new related functional compounds is crucial. This work uses a heteroepitaxial approach supported by theoretical calculation to stabilize PbSnO3 thin films with different orientations. The analyses of X-ray diffraction and transmission electron microscopy unveil the structural information. A typical antiferroelectric feature with double hysteresis and butterfly loops is observed through electrical characterizations consistent with the theoretical prediction. The phase transition is monitored, and the transition temperatures are determined based on temperature-dependent structural and electrical characterizations. Furthermore, the microscopic antiferroelectric order is noticed under atomic resolution images via scanning transmission electron microscopy. This work offers a breakthrough in synthesizing epitaxial PbSnO3 thin films and comprehensively understanding its anisotropic antiferroelectric behavior.
RESUMEN
The performance and suitability of a new electron energy filter in combination with a hybrid pixel, direct electron detector for analytical (scanning) transmission electron microscopy are demonstrated using four examples. The STEM-EELS capabilities of the CEOS Energy Filtering and Imaging Device (CEFID) were tested with focus on weak signals and high spatio-temporal resolution. A multiferroic, multilayer structure of REMnO3 (RE = Yb, Er, Tb, Y), grown on yttria-stabilized zirconia (YSZ), is used to exemplify that this new instrumental setup produces valuable electron energy-loss spectroscopy (EELS) data at high energy losses even when using short acquisition times, providing detailed chemical information about the interfaces in this complex multilayer sample. Another functional oxide, namely a ferromagnetic La2NiMnO6 thin film grown on SrTiO3, demonstrates that atomically resolved spectrum images can be recorded, using short dwell times and moderate beam currents in order to warrant the integrity of the sample. In a third example, inhomogeneously Er-doped YSZ shows by EELS spectrum imaging that elements at low concentrations can be detected semi-quantitatively, uncovering the expected layered Er distribution but revealing substantial interdiffusion. In a final example, we simply demonstrate that the hybrid pixel detector in combination with the energy filter can also be used for energy-filtered imaging and thus for elemental mapping complementary to EELS in scanning transmission mode.
RESUMEN
We have studied electronic transport in undoped GaAs/SrTiO3core-shell nanowires standing on their Si substrate with two-tip scanning tunneling microscopy in ultrahigh vacuum. The resistance profile along the nanowires is proportional to the tip separation with resistances per unit length of a few GΩ/µm. Examination of the different transport pathways parallel to the nanowire growth axis reveals that the measured resistance is consistent with a conduction along the interfacial states at the GaAs{110} sidewalls, the 2 nm thick SrTiO3shell being as much as resistive, despite oxygen deficient growth conditions. The origin of the shell resistivity is discussed in light of the nanowire analysis with transmission electron microscopy and Raman spectroscopy, providing good grounds for the use of SrTiO3shells as gate insulators.
RESUMEN
Engineering oxygen vacancy formation and distribution is a powerful route for controlling the oxygen sublattice evolution that affects diverse functional behavior. The controlling of the oxygen vacancy formation process is particularly important for inducing topotactic phase transitions that occur by transformation of the oxygen sublattice. Here we demonstrate an epitaxial nanocomposite approach for exploring the spatial control of topotactic phase transition from a pristine perovskite phase to an oxygen vacancy-ordered brownmillerite (BM) phase in a model oxide La0.7Sr0.3MnO3 (LSMO). Incorporating a minority phase NiO in LSMO films creates ultrahigh density of vertically aligned epitaxial interfaces that strongly influence the oxygen vacancy formation and distribution in LSMO. Combined structural characterizations reveal strong interactions between NiO and LSMO across the epitaxial interfaces leading to a topotactic phase transition in LSMO accompanied by significant morphology evolution in NiO. Using the NiO nominal ratio as a single control parameter, we obtain intermediate topotactic nanostructures with distinct distribution of the transformed LSMO-BM phase, which enables systematic tuning of magnetic and electrical transport properties. The use of self-assembled heterostructure interfaces by the epitaxial nanocomposite platform enables more versatile design of topotactic phase structures and correlated functionalities that are sensitive to oxygen vacancies.
RESUMEN
Multiferroics offer an elegant means to implement voltage control and on the fly reconfigurability in microscopic, nanoscaled systems based on ferromagnetic materials. These properties are particularly interesting for the field of magnonics, where spin waves are used to perform advanced logical or analogue functions. Recently, the emergence of nanomagnonics is expected to eventually lead to the large-scale integration of magnonic devices. However, a compact voltage-controlled, on demand reconfigurable magnonic system has yet to be shown. Here, we introduce the combination of multiferroics with ferromagnets in a fully epitaxial heterostructure to achieve such voltage-controlled and reconfigurable magnonic systems. Imprinting a remnant electrical polarization in thin multiferroic BiFeO3 with a periodicity of 500 nm yields a modulation of the effective magnetic field in the micrometer-scale, ferromagnetic La2/3Sr1/3MnO3 magnonic waveguide. We evidence the magnetoelectric coupling by characterizing the spin wave propagation spectrum in this artificial, voltage induced, magnonic crystal and demonstrate the occurrence of a robust magnonic band gap with >20 dB rejection.
RESUMEN
The annealing process is an important step common to epitaxial films prepared by chemical solution deposition methods. It is so because the final microstructure of the films can be severely affected by the precise features of the thermal processing. In this work we analyze the structural and magnetic properties of double perovskite La2CoMnO6 and La2NiMnO6 epitaxial thin films prepared by polymer-assisted deposition (PAD) and crystallized by rapid thermal annealing (RTA). It is found that samples prepared by RTA have similar values of saturation magnetization and Curie temperature to their counterparts prepared by using conventional thermal annealing (CTA) processes, thus indicating low influence of the heating rates on the B-B' site cationic ordering of the A2BB'O6 double perovskite structure. However, a deeper analysis of the magnetic behavior suggested some differences in the actual microstructure of the films.
RESUMEN
Successful synthesis of ordered porous, multi-component complex materials requires a series of coordinated processes, typically including fabrication of a master template, deposition of materials within the pores to form a negative structure, and a third deposition or etching process to create the final, functional template. Translating the utility and the simplicity of the ordered nanoporous geometry of binary oxide templates to those comprising complex functional oxides used in energy, electronic, and biology applications has been met with numerous critical challenges. This review surveys the current state of commonly used complex material nanoporous template synthesis techniques derived from the base anodic aluminum oxide (AAO) geometry.
RESUMEN
A new high-vacuum multipurpose diffractometer (called FORTE from the French acronyms of the project) has recently been installed at the tender/hard X-ray SIRIUS beamline of Synchrotron SOLEIL, France. The geometry chosen allows one to work either in the classical Eulerian four-circle geometry for bulk X-ray diffraction (XRD) or in the z-axis geometry for surface XRD. The diffractometer nicely fits the characteristics of the SIRIUS beamline, optimized to work in the 1.1-4.5â keV range, and allows one to perform unprecedented diffraction anomalous fine structure (DAFS) experiments in the tender X-ray region, also around non-specular reflections, covering a large reciprocal-space volume. Installation of an X-ray fluorescence detector on a dedicated flange allows simultaneous DAFS and X-ray absorption (XAS) measurements. The access to the tender X-ray region paves the way to resonant investigations around the L-edges of second-row transition elements which are constituents of functional oxide materials. It also enables access to several edges of interest for semiconductors. Finally, the control architecture based on synchronized Delta Tau units opens up exciting perspectives for improvement of the mechanical sphere of confusion.
RESUMEN
Ferroelectric tunnel junction (FTJ) based memristors exhibiting continuous electric field controllable resistance states have been considered promising candidates for future high-density memories and advanced neuromorphic computational architectures. However, the use of rigid single crystal substrate and high temperature growth of the epitaxial FTJ thin films constitutes the main obstacles to using this kind of heterostructure in flexible computing devices. Here, we report the integration of centimeter-scale single crystalline FTJs on flexible plastic substrates, by water-etching based epitaxial oxide membrane lift-off and the following transfer. The resulting highly flexible FTJ membranes retain the single-crystalline structure along with stable and switchable ferroelectric polarization as the grown-on single crystal substrate state. We show that the obtained flexible memristors, i.e., FTJs on plastic substrates, present high speed and low voltage mediated memristive behaviors with resistance changes over 500% and are stable against shape change. This work is an essential step toward the realization of epitaxial ultrathin ferroelectric oxide film-based electronics on large-area, flexible, and affordable substrates.
RESUMEN
Strain engineering of thin films is a conventionally employed approach to enhance material properties and to energetically prefer ground states that would otherwise not be attainable. Controlling strain states in perovskite oxide thin films is usually accomplished through coherent epitaxy by using lattice-mismatched substrates with similar crystal structures. However, the limited choice of suitable oxide substrates makes certain strain states experimentally inaccessible and a continuous tuning impossible. Here, we report a strategy to continuously tune epitaxial strains in perovskite films grown on Si(001) by utilizing the large difference of thermal expansion coefficients between the film and the substrate. By establishing an adsorption-controlled growth window for SrTiO3 thin films on Si using hybrid molecular beam epitaxy, the magnitude of strain can be solely attributed to thermal expansion mismatch, which only depends on the difference between growth and room temperature. Second-harmonic generation measurements revealed that structure properties of SrTiO3 films could be tuned by this method using films with different strain states. Our work provides a strategy to generate continuous strain states in oxide/semiconductor pseudomorphic buffer structures that could help achieve desired material functionalities.
RESUMEN
Materials that can couple electrical and mechanical properties constitute a key element of smart actuators, energy harvesters, or many sensing devices. Within this class, functional oxides display specific mesoscale responses which often result in great sensitivity to small external stimuli. Here, a novel combination of molecular beam epitaxy and a water-based chemical-solution method is used for the design of mechanically controlled multilevel device integrated on silicon. In particular, the possibility of adding extra functionalities to a ferroelectric oxide heterostructure by n-doping and nanostructuring a BaTiO3 thin film on Si(001) is explored. It is found that the ferroelectric polarization can be reversed, and resistive switching can be measured, upon a mechanical load in epitaxial BaTiO3-δ /La0.7 Sr0.3 MnO3 /SrTiO3 /Si columnar nanostructures. A flexoelectric effect is found, stemming from substantial strain gradients that can be created with moderate loads. Simultaneously, mechanical effects on the local conductivity can be used to modulate a nonvolatile resistive state of the BaTiO3-δ heterostructure. As a result, three different configurations of the system become accessible on top of the usual voltage reversal of polarization and resistive states.
RESUMEN
High-quality thermoelectric La0.2Sr0.8TiO3 (LSTO) films, with thicknesses ranging from 20 nm to 0.7 µm, have been epitaxially grown on SrTiO3(001) substrates by enhanced solid-source oxide molecular-beam epitaxy. All films are atomically flat (with rms roughness < 0.2 nm), with low mosaicity (<0.1°), and present very low electrical resistivity (<5 × 10-4 Ω cm at room temperature), one order of magnitude lower than standard commercial Nb-doped SrTiO3 single-crystalline substrate. The conservation of transport properties within this thickness range has been confirmed by thermoelectric measurements where Seebeck coefficients of approximately -60 µV/K have been recorded for all films. These LSTO films can be integrated on Si for non-volatile memory structures or opto-microelectronic devices, functioning as transparent conductors or thermoelectric elements.
RESUMEN
Insulating SrTiO3 (STO) can host 2D electron systems (2DESs) on its surfaces, caused by oxygen defects. This study shows that the STO surface exhibits phase separation once the 2DES is formed and relates this inhomogeneity to recently reported magnetic order at STO surfaces and interfaces. The results open pathways to exploit oxygen defects for engineering the electronic and magnetic properties of oxides.
RESUMEN
We have studied the growth of a SrTiO3 shell on self-catalyzed GaAs nanowires grown by vapor-liquid-solid assisted molecular beam epitaxy on Si(111) substrates. To control the growth of the SrTiO3 shell, the GaAs nanowires were protected using an arsenic capping/decapping procedure in order to prevent uncontrolled oxidation and/or contamination of the nanowire facets. Reflection high energy electron diffraction, scanning electron microscopy, transmission electron microscopy, and X-ray photoelectron spectroscopy were performed to determine the structural, chemical, and morphological properties of the heterostructured nanowires. Using adapted oxide growth conditions, it is shown that most of the perovskite structure SrTiO3 shell appears to be oriented with respect to the GaAs lattice. These results are promising for achieving one-dimensional epitaxial semiconductor core/functional oxide shell nanostructures.
RESUMEN
2D electron systems (2DESs) in functional oxides are promising for applications, but their fabrication and use, essentially limited to SrTiO3 -based heterostructures, are hampered by the need for growing complex oxide overlayers thicker than 2 nm using evolved techniques. It is demonstrated that thermal deposition of a monolayer of an elementary reducing agent suffices to create 2DESs in numerous oxides.
RESUMEN
The epitaxial growth of functional oxides on silicon substrates requires atomically defined surfaces, which are most effectively prepared using Sr-induced deoxidation. The manipulation of metallic Sr is nevertheless very delicate and requires alternative buffer materials. In the present study the applicability of the chemically much more stable SrO in the process of native-oxide removal and silicon-surface stabilization was investigated using the pulsed-laser deposition technique (PLD), while the as-derived surfaces were analyzed in situ using reflection high-energy electron diffraction and ex situ using X-ray photoelectron spectroscopy, X-ray reflectivity, and atomic force microscopy. After the deposition of the SrO over Si/SiO2, in a vacuum, different annealing conditions, with the temperature ranging up to 850 °C, were applied. Because the deposition took place in a vacuum, a multilayer composed of SrO, Sr-silicate, modified Si, and Si as a substrate was initially formed. During the subsequent annealing the topmost layer epitaxially orders in the form of islands, while a further increase in the annealing temperature induced rapid desorption and surface deoxidation, leading to a 2 × 1 Sr-reconstructed silicon surface. However, the process is accompanied by distinctive surface roughening, and therefore the experimental conditions must be carefully optimized to minimize the effect. The results of the study revealed, for the first time, an effective pathway for the preparation of a SrO-induced buffer layer on a silicon substrate using PLD, which can be subsequently utilized for the epitaxial growth of functional oxides.