RESUMEN

The authentication of wireless devices through physical layer attributes has attracted a fair amount of attention recently. Recent work in this area has examined various features extracted from the wireless signal to either identify a uniqueness in the channel between the transmitter-receiver pair or more robustly identify certain transmitter behaviors unique to certain devices originating from imperfect hardware manufacturing processes. In particular, the carrier frequency offset (CFO), induced due to the local oscillator mismatch between the transmitter and receiver pair, has exhibited good detection capabilities in stationary and low-mobility transmission scenarios. It is still unclear, however, how the CFO detection capability would hold up in more dynamic time-varying channels where there is a higher mobility. This paper experimentally demonstrates the identification accuracy of CFO for wireless devices in time-varying channels. To this end, a software-defined radio (SDR) testbed is deployed to collect CFO values in real environments, where real transmission and reception are conducted in a vehicular setup. The collected CFO values are used to train machine-learning (ML) classifiers to be used for device identification. While CFO exhibits good detection performance (97% accuracy) for low-mobility scenarios, it is found that higher mobility (35 miles/h) degrades (72% accuracy) the effectiveness of CFO in distinguishing between legitimate and non-legitimate transmitters. This is due to the impact of the time-varying channel on the quality of the exchanged pilot signals used for CFO detection at the receivers.

RESUMEN

Communication signal reconstruction technology represents a critical area of research within communication countermeasures and signal processing. Considering traditional OFDM signal reconstruction methods' intricacy and suboptimal reconstruction performance, a dual discriminator CGAN model incorporating LSTM and Transformer is proposed. When reconstructing OFDM signals using the traditional CNN network, it becomes challenging to extract intricate temporal information. Therefore, the BiLSTM network is incorporated into the first discriminator to capture timing details of the IQ (In-phase and Quadrature-phase) sequence and constellation map information of the AP (Amplitude and Phase) sequence. Subsequently, following the addition of fixed position coding, these data are fed into the core network constructed based on the Transformer Encoder for further learning. Simultaneously, to capture the correlation between the two IQ signals, the VIT (Vision in Transformer) concept is incorporated into the second discriminator. The IQ sequence is treated as a single-channel two-dimensional image and segmented into pixel blocks containing IQ sequence through Conv2d. Fixed position coding is added and sent to the Transformer core network for learning. The generator network transforms input noise data into a dimensional space aligned with the IQ signal and embedding vector dimensions. It appends identical position encoding information to the IQ sequence before sending it to the Transformer network. The experimental results demonstrate that, under commonly utilized OFDM modulation formats such as BPSK, QPSK, and 16QAM, the time series waveform, constellation diagram, and spectral diagram exhibit high-quality reconstruction. Our algorithm achieves improved signal quality while managing complexity compared to other reconstruction methods.

RESUMEN

Harmonic generation and utilization are significant topics in nonlinear science. Although the progress in the microwave region has been expedited by the development of time-modulated metasurfaces, one major issue of these devices is the strong entanglement of multiple harmonics, leading to criticism of their use in frequency-division multiplexing (FDM) applications. Previous studies have attempted to overcome this limitation, but they suffer from designing complexity or insufficient controlling capability. Here a new space-time-coding metasurface (STCM) is proposed to independently and precisely synthesize not only the phases but also the amplitudes of various harmonics. This promising feature is successfully demonstrated in wireless space- and frequency-division multiplexing experiments, where modulated and unmodulated signals are simultaneously transmitted via different harmonics using a shared STCM. To illustrate the advantages, binary frequency shift keying (BFSK) and quadrature phase shift keying (QPSK) modulation schemes are respectively implemented. Behind the intriguing functionality, the mechanism of the space-time coding strategy and the analytical designing method are elaborated, which are validated numerically and experimentally. It is believed that the achievements can potentially propel the time-vary metasurfaces in the next-generation wireless applications.

RESUMEN

For orthogonal frequency division multiplexing (OFDM) systems in high-mobility scenarios, the estimation of time-varying multipath channels not only has a large error, which affects system performance, but also requires plenty of pilots, resulting in low spectral efficiency. To address these issues, we propose a time-varying multipath channel estimation method based on distributed compressed sensing and a multi-symbol complex exponential basis expansion model (MS-CE-BEM) by exploiting the temporal correlation and the joint delay sparsity of wideband wireless channels within the duration of multiple OFDM symbols. Furthermore, in the proposed method, a sparse pilot pattern with the self-cancellation of pilot intercarrier interference (ICI) is adopted to reduce the input parameter error of the MS-CE-BEM, and a symmetrical extension technique is introduced to reduce the modeling error. Simulation results show that, compared with existing methods, this proposed method has superior performances in channel estimation and spectrum utilization for sparse time-varying channels.

RESUMEN

In the modern technological era of sophisticated applications and high-quality communications, a platform of clever strategy and quickly updated systems is needed. It should be capable of withstanding the fastest emerging problems like signal attenuation and hostile actions intended to harm the whole network. The main contributions of this work are the production of an OFDM system (with low cost) that can sustain high-speed communications and be easily adjusted with new integrated code while exhibiting the feasibility of implementing a transmitter-receiver system in the same DSP and demonstrating the holistic approach with the qualitative integration of such an architecture in a warfare scenario. Specifically, in this research, the point of view is toward three facts. The first is to show a method of quick self-checking the operational status of a digital signal processor (DSP) platform and then the pedagogical issues of how to fast check and implement an updated code inside DSPs through simple schematics. The second point is to present the prototype system that can easily be programmed using a graphical user interface (GUI) and can change its properties (such as the transmitted modulated sinusoids-orthogonal frequency division multiplexing subcarriers). Alongside the presentation, the measurements are presented and discussed. These were acquired with the use of an oscilloscope and spectrum analyzer. The third point is to qualitatively show the application of such a system inside a modern warfare environment and to recommend various potential system responses according to the development of such a platform of reconfigurable implemented OFDM systems. The implementation was performed for two types of systems: (1) transmitter and (2) transmitter-receiver system. Notably, the system acts quickly with a delay of about 1 msec in the case of transmitting and receiving in the same DSP, suggesting excellent future results under real conditions.

RESUMEN

Inter-areal information transmission in the brain cortex relates to cognitive functions. Researches used to pay attention to activity pattern transmission, signals gating, or routing in neuronal networks. However, the underlying mechanism of simultaneous transmission of multiple neural signals in the same channel across networks remains unclear. In this work, we construct a two-layer feedforward neuronal network (sender-receiver) with each layer's intrinsic rhythms consisting of slow- (low-frequency) and fast- gamma rhythms (high-frequency), investigating how to realize simultaneous transmission of multiple signals in neuronal systems. With the aid of resonance and frequency analysis, it is shown that low- and high-frequency signals can be transmitted simultaneously in such a feedforward network through frequency division multiplexing (FDM) communication. The transmission performance is related to the local resonance, connectivity, as well as background noise. Moreover, low- and high-frequency signals can also be gated or selected with appropriate adjustments of recurrent connection strength and delay, and background noise. Our model might provide a novel insight into the underlying mechanism of complex signals communication between different cortex areas.

RESUMEN

In the domain of optical fiber distributed acoustic sensing, the persistent challenge of extending sensing distances while concurrently improving spatial resolution and frequency response range has been a complex endeavor. The amalgamation of pulse compression and frequency division multiplexing methodologies has provided certain advantages. Nevertheless, this approach is accompanied by the drawback of significant bandwidth utilization and amplified hardware investments. This study introduces an innovative distributed optical fiber acoustic sensing system aimed at optimizing the efficient utilization of spectral resources by combining compressed pulses and frequency division multiplexing. The system continuously injects non-linear frequency modulation detection pulses spanning various frequency ranges. The incorporation of non-uniform frequency division multiplexing augments the vibration frequency response spectrum. Additionally, nonlinear frequency modulation adeptly reduces crosstalk and enhances sidelobe suppression, all while maintaining a favorable signal-to-noise ratio. Consequently, this methodology substantially advances the spatial resolution of the sensing system. Experimental validation encompassed the multiplexing of eight frequencies within a 120 MHz bandwidth. The results illustrate a spatial resolution of approximately 5 m and an expanded frequency response range extending from 1 to 20 kHz across a 16.3 km optical fiber. This achievement not only enhances spectral resource utilization but also reduces hardware costs, making the system even more suitable for practical engineering applications.

RESUMEN

For Orthogonal Frequency Division Multiplexing (OFDM) systems, the most significant problem is the peak-to-average power ratio. The utilisation of partial transmission sequence, often known as PTS, is an efficient method for reducing PAPR. When it comes to minimizing the peak-to-average power ratio (PAPR) in Orthogonal Frequency Division Multiplexing (OFDM) Systems, PTS is one of the most effective approaches that may be used. Due to the substantial data load, using peak-to-average power ratio in OFDM is challenging. The most crucial problem with OFDM is achieving better results by lowering PAPR. Provide a PTS in this research that is based on the Chaotic Biogeography Based Optimization (CBBO) algorithm to effectively address the high PAPR issue that exists in Generalized Frequency Division Multiplexing (GFDM) waveforms using Hermitian Symmetry property is used. The Hermitian symmetry is utilised in order to acquire a real-valued time-domain signal. Phase rotation factor combinations are carried out in an effective and optimal manner through the utilisation of an innovative combination of optimization techniques. In comparison to conventional optimization techniques, a new hybrid optimization offers quick convergence quality and minimal complexity. When compared to traditional PTS methods such traditional GFDM and OFDM-PTS, experimental results demonstrate that the suggested CBBO-PTS technique significantly improves on minimizing PAPR.

RESUMEN

We put forward and demonstrate a silicon photonics (SiPh)-based mode division multiplexed (MDM) optical power splitter that supports transverse-electric (TE) single-mode, dual-mode, and triple-mode (i.e., TE0, TE1, and TE2). An optical power splitter is needed for optical signal distribution and routing in optical interconnects. However, a traditional optical splitter only divides the power of the input optical signal. This means the same data information is received at all the output ports of the optical splitter. The powers at different output ports may change depending on the splitting ratio of the optical splitter. The main contributions of our proposed optical splitter are: (i) Different data information is received at different output ports of the optical splitter via the utilization of NOMA. By adjusting the power ratios of different channels in the digital domain (i.e., via software control) at the Tx, different channel data information can be received at different output ports of the splitter. It can increase the flexibility of optical signal distribution and routing. (ii) Besides, the proposed optical splitter can support the fundamental TE0 mode and the higher modes TE1, TE2, etc. Supporting mode-division multiplexing and multi-mode operation are important for future optical interconnects since the number of port counts is limited by the chip size. This can significantly increase the capacity besides wavelength division multiplexing (WDM) and spatial division multiplexing (SDM). The integrated SiPh MDM optical power splitter consists of a mode up-conversion section implemented by asymmetric directional couplers (ADCs) and a Y-branch structure for MDM power distribution. Here, we also propose and discuss the use of the Genetic algorithm (GA) for the MDM optical power splitter parameter optimization. Finally, to provide adjustable data rates at different output ports after the MDM optical power splitter, non-orthogonal multiple access-orthogonal frequency division multiplexing (NOMA-OFDM) is also employed. Experimental results validate that, in three modes (TE0, TE1, and TE2), user-1 and user-2 achieve data rates of (user-1: greater than 22 Gbit/s; user-2: greater than 12 Gbit/s) and (user-1: greater than 12 Gbit/s; user-2: 24 Gbit/s), respectively, at power-ratio (PR) = 2.0 or 3.0. Each channel meets the hard-decision forward-error-correction (HD-FEC, i.e., BER = 3.8 × 10-3) threshold. The proposed method allows flexible data rate allocation for multiple users for optical interconnects and system-on-chip networks.

RESUMEN

In this research, a pulse oximeter based on quadrature multiplexing of AM-PPG signals is proposed. The oximeter is operated by a microcontroller and employs a simple amplitude modulation technique to mitigate noise interference during SpO2 measurement. The two AM-PPG signals (RED and IR) are quadrature multiplexed using carrier signals with equal frequencies but a 90-degree phase difference. The study focused on noise interference caused by light intensity and hand movement. The experiment was conducted under three different levels of light intensity: 200 Lux, 950 Lux, and 2200 Lux. For each light intensity level, the SpO2 level was measured under three scenarios: hand still, shadow movement over the hand, and hand shaking. A comparison between the proposed technique and the conventional method reveals that the proposed technique offers a superior performance. The relative error of the measured SpO2 level using the proposed technique was less than 3.1% overall. Based on the study, the proposed technique is less affected by noise interference caused by light intensity and hand movement compared to the conventional method. In addition, the proposed technique has an advantage over contemporary methods in terms of computational complexity. Consequently, the proposed technique can be applied to wearable devices that include SpO2 measurement functionality.

Asunto(s)

RESUMEN

Visible light communication (VLC) is an emerging mode of wireless communication that supports both illumination and communication. One essential function of VLC systems is the dimming control, which requires a sensitive receiver for low-light conditions. The use of an array of single-photon avalanche diodes (SPADs) is one promising approach to enhancing receivers' sensitivity in a VLC system. However, because of the non-linear effects brought on by the SPAD dead time, an increase in the brightness of the light might degrade its performance. In this paper, an adaptive SPAD receiver is proposed for VLC systems to ensure reliable operation under various dimming levels. In the proposed receiver, a variable optical attenuator (VOA) is used to adaptively control the SPAD's incident photon rate according to the instantaneous received optical power so that SPAD operates in its optimal conditions. The application of the proposed receiver in systems with various modulation schemes is investigated. When binary on-off keying (OOK) modulation is employed due to its good power efficiency, two dimming control methods of the IEEE 802.15.7 standard based on analogue and digital dimming are considered. We also investigate the application of the proposed receiver in the spectral efficient VLC systems with multi-carrier modulation schemes, i.e., direct current (DCO) and asymmetrically clipped optical (ACO) orthogonal frequency division multiplexing (OFDM). Through extensive numerical results, it is demonstrated that the suggested adaptive receiver outperforms the conventional PIN PD and SPAD array receivers in terms of bit error rate (BER) and achievable data rate.

RESUMEN

In this paper, we present a hybrid frequency shift keying and frequency division multiplexing (i.e., FSK-FDM) approach for information embedding in dual-function radar and communication (DFRC) design to achieve an improved communication data rate. Since most of the existing works focus on merely two-bit transmission in each pulse repetition interval (PRI) using different amplitude modulation (AM)- and phased modulation (PM)-based techniques, this paper proposes a new technique that doubles the data rate by using a hybrid FSK-FDM technique. Note that the AM-based techniques are used when the communication receiver resides in the side lobe region of the radar. In contrast, the PM-based techniques perform better if the communication receiver is in the main lobe region. However, the proposed design facilitates the delivery of information bits to the communication receivers with an improved bit rate (BR) and bit error rate (BER) regardless of their locations in the radar's main lobe or side lobe regions. That is, the proposed scheme enables information encoding according to the transmitted waveforms and frequencies using FSK modulation. Next, the modulated symbols are added together to achieve a double data rate using the FDM technique. Finally, each transmitted composite symbol contains multiple FSK-modulated symbols, resulting in an increased data rate for the communication receiver. Numerous simulation results are presented to validate the effectiveness of the proposed technique.

Asunto(s)

RESUMEN

This paper is concerned with mobile coded orthogonal frequency division multiplexing (OFDM) systems. In the high-speed railway wireless communication system, an equalizer or detector should be used to mitigate the intercarrier interference (ICI) and deliver the soft message to the decoder with the soft demapper. In this paper, a Transformer-based detector/demapper is proposed to improve the error performance of the mobile coded OFDM system. The soft modulated symbol probabilities are computed by the Transformer network, and are then used to calculate the mutual information to allocate the code rate. Then, the network computes the codeword soft bit probabilities, which are delivered to the classical belief propagation (BP) decoder. For comparison, a deep neural network (DNN)-based system is also presented. Numerical results show that the Transformer-based coded OFDM system outperforms both the DNN-based and the conventional system.

RESUMEN

Enhancing multi-gas detectability using photoacoustic spectroscopy capable of simultaneous detection, highly selectivity and less cross-interference is essential for dissolved gas sensing application. A T-type photoacoustic cell was designed and verified to be an appropriate sensor, due to the resonant frequencies of which are determined jointly by absorption and resonant cylinders. The three designated resonance modes were investigated from both simulation and experiments to present the comparable amplitude responses by introducing excitation beam position optimization. The capability of multi-gas detection was demonstrated by measuring CO, CH4 and C2H2 simultaneously using QCL, ICL and DFB lasers as excitation sources respectively. The influence of potential cross-sensitivity towards humidity have been examined in terms of multi-gas detection. The experimentally determined minimum detection limits of CO, CH4 and C2H2 were 89ppb, 80ppb and 664ppb respectively, corresponding to the normalized noise equivalent absorption coefficients of 5.75 × 10-7 cm-1 W Hz-1/2, 1.97 × 10-8 cm-1 W Hz-1/2 and 4.23 × 10-8 cm-1 W Hz-1/2.

RESUMEN

Due to the popularity of different high bandwidth applications, it is becoming increasingly difficult to satisfy the huge data capacity requirements, since the traditional electrical interconnects suffer significantly from limited bandwidth and huge power consumption. Silicon photonics (SiPh) is one of the important technologies for increasing interconnect capacity and decreasing power consumption. Mode-division multiplexing (MDM) allows signals to be transmitted simultaneously, at different modes, in a single waveguide. Wavelength-division multiplexing (WDM), non-orthogonal multiple access (NOMA) and orthogonal-frequency-division multiplexing (OFDM) can also be utilized to further increase the optical interconnect capacity. In SiPh integrated circuits, waveguide bends are usually inevitable. However, for an MDM system with a multimode bus waveguide, the modal fields will become asymmetric when the waveguide bend is sharp. This will introduce inter-mode coupling and inter-mode crosstalk. One simple approach to achieve sharp bends in multimode bus waveguide is to use a Euler curve. Although it has been reported in the literature that sharp bends based on a Euler curve allow high performance and low inter-mode crosstalk multimode transmissions, we discover, by simulation and experiment, that the transmission performance between two Euler bends is length dependent, particularly when the bends are sharp. We investigate the length dependency of the straight multimode bus waveguide between two Euler bends. High transmission performance can be achieved by a proper design of the waveguide length, width, and bend radius. By using the optimized MDM bus waveguide length with sharp Euler bends, proof-of-concept NOMA-OFDM experimental transmissions, supporting two MDM modes and two NOMA users, are performed.

RESUMEN

Since orthogonal frequency division multiplexing (OFDM) systems are very susceptible to symbol timing offset (STO) and carrier frequency offset (CFO), which cause inter-symbol interference (ISI) and inter-carrier interference (ICI), accurate STO and CFO estimations are very important. In this study, first, a new preamble structure based on the Zadoff-Chu (ZC) sequences was designed. On this basis, we proposed a new timing synchronization algorithm, called the continuous correlation peak detection (CCPD) algorithm, and its improved algorithm: the accumulated correlation peak detection (ACPD) algorithm. Next, the correlation peaks that were obtained during the timing synchronization were used for the frequency offset estimation. For this, the quadratic interpolation algorithm was adopted as the frequency offset estimation algorithm, which was better than the fast Fourier transform (FFT) algorithm. The simulation results showed that when the correct timing probability reached 100%, under the parameters of m = 8 and N = 512, the performance of the CCPD algorithm was 4 dB higher than that of Du's algorithm, and that of the ACPD algorithm was 7 dB. Under the same parameters, the quadratic interpolation algorithm also had a great performance improvement in both small and large frequency offsets, when compared with the FFT algorithm.

RESUMEN

The performance of an all fibered near-infrared (NIR) single-channel frequency-division multiplexing wavelength-modulated laser heterodyne radiometer (FDM WM-LHR) is demonstrated in ground-based solar occultation mode. The system modulates the laser through the high-frequency signal output by the lock-in amplifier to replace the traditional chopper modulation, making it more stable and compact. Moreover, personal computers are used to simultaneously control the operating current of two distributed feedback (DFB) lasers through a general purpose interface bus-universal serial bus (GPIB-USB), thereby controlling the central wavelength of the laser at 1602.88 and 1653.727 nm, which serve as the absorption lines for the local oscillator detection of the two main greenhouse gases: CO2 and CH4. Firstly, the performance of traditional laser heterodyne radiometer (LHR) and the wavelength-modulated laser heterodyne radiometer (WM-LHR) are compared. The results reveal that both the radiometers have an optimized 2f signal when the modulation amplitude m = 2.2. In the actual measurement, 0.25 V and 0.21 V are selected as the modulation amplitude of the laser for the detection of CH4 and CO2. Under the same experimental parameters, at 1602.88 nm, the signal-to-noise ratio (SNR) for the 2f signal of CO2 in the WM-LHR system is 500.24, while that for the direct absorption signal (DAS) of CO2 in the traditional LHR system is 337.94. At 1653.727 nm, the SNR for the 2f signal in the WM-LHR system and the DAS of CH4 in the traditional LHR system are 512.04 and 389.58, respectively. Obviously, the SNR for the WM-LHR system is greatly improved. Finally, the application of frequency-division multiplexing (FDM) technology in the WM-LHR system is discussed. The modulation frequency of the two lasers should be appropriately selected to avoid interference between the signals. Overall, the results show that the FDM WM-LHR system can not only detect multiple gases simultaneously but also reduce the implementation cost of the ground-based radiometer. In addition, this study provides useful insights on planetary atmosphere exploration.

RESUMEN

Silicon photonics (SiPh) are considered a promising technology for increasing interconnect speed and capacity while decreasing power consumption. Mode division multiplexing (MDM) enables signals to be transmitted in different orthogonal modes in a single waveguide core. Wideband MDM components simultaneously supporting wavelength division multiplexing (WDM) and orthogonal frequency-division multiplexing (OFDM) can significantly increase the transmission capacity for optical interconnects. In this work, we propose, fabricate and demonstrate a wideband and channel switchable MDM optical power divider on an SOI platform, supporting single, dual and triple modes. The switchable MDM power divider consists of two parts. The first part is a cascaded Mach-Zehnder interferometer (MZI) for switching the data from their original TE0, TE1 and TE2 modes to different modes among themselves. After the target modes are identified, mode up-conversion and Y-branch are utilized in the second part for the MDM power division. Here, 48 WDM wavelength channels carrying OFDM data are successfully switched and power divided. An aggregated capacity of 7.682 Tbit/s is achieved, satisfying the pre-forward error correction (pre-FEC) threshold (bit-error-rate, BER = 3.8 × 10-3). Although up to three MDM modes are presented in the proof-of-concept demonstration here, the proposed scheme can be scaled to higher order modes operation.

Asunto(s)

RESUMEN

Orthogonal frequency division multiplexing (OFDM) has the characteristics of high spectrum efficiency and excellent anti-multipath interference ability. It is the most popular and mature technology currently in wireless communication. However, OFDM is a multi-carrier system, which inevitably has the problem of a high peak-to-average power ratio (PAPR), and s signal with too high PAPR is prone to distortion when passing through an amplifier due to nonlinearity. To address the troubles caused by high PAPR, we proposed an improved tone reservation (I-TR) algorithm to alleviate the above native phenomenon, which will pay some modest pre-calculations to estimate the rough proportion of peak reduction tone (PRT) to determine the appropriate output power allocation threshold then utilize a few iterations to converge to the near-optimal PAPR. Furthermore, our proposed scheme significantly outperforms previous works in terms of PAPR performance and computational complexity, such as selective mapping (SLM), partial transmission sequence (PTS), TR, tone injection (TI), etc. The simulation results show that in our proposed scheme, the PAPR is appreciably reduced by about 6.44 dB compared with the original OFDM technique at complementary cumulative distribution function (CCDF) equal to 10-3, and the complexity of I-TR has reduced by approximately 96% compared to TR. Besides, as for bit error rate (BER), our proposed method always outperforms the original OFDM without any sacrifice.

Asunto(s)

RESUMEN

In the past few years, wireless communications based on digital coding metasurfaces have gained research interest owing to their simplified architectures and low cost. However, in most of the metasurface-based wireless systems, a single-polarization scenario is used, limiting the channel capacities. To solve the problem, multiplexing methods have been adopted, but the system complexity is inevitably increased. Here, a space-frequency-polarization-division multiplexed wireless communication system is proposed using an anisotropic space-time-coding digital metasurface. By separately designing time-varying control voltage sequences for differently oriented varactor diodes integrated on the metasurface, we achieve frequency-polarization-division multiplexed modulations. By further introducing different time-delay gradients to the control voltage sequences in two polarization directions, we successfully obtain space-frequency-polarization-division multiplexed modulations to realize a wireless communication system with a new architecture. The new communication system is designed with compact dual-polarized meta-elements, and can improve channel capacity and space utilization. Experimental results demonstrate the high-performance and real-time transmission capability of the proposed communication system, confirming its potential application in multiple-user collaborative wireless communications.