RESUMEN
This study investigated the muscle strength and performance fatigability of the forearms in eight male orthopaedic surgeons when performing bone screw fixations. Each surgeon performed an eight-bone screws operations in a porcine femur model to simulate fractural fixation using plating technique. The pre- and post-fatigue maximum isometric forces and corresponding electromyography responses were measured to assess the forearm muscle strength loss and fatigue due to screwing. Results showed that after eight bone screws were inserted, the maximal grip force, maximal driving torque and maximal push force losses were approximately 29%, 20% and 23%, respectively. While the grip force and/or driving torque acting, both the brachioradialis and extensor carpi ulnaris had a higher percentage change of EMG than the biceps brachii. The driving forces decreased with the number of screw insertions; however, the insertion time increased parabolically with the number of screws and significantly decreased the insertion rate of the screws, indicating that forearm muscle fatigue may occur in surgeons who treat fracture fixation using more than eight bone screws.
Asunto(s)
Tornillos Óseos , Fijación de Fractura , Enfermedades Profesionales/etiología , Cirujanos Ortopédicos , Trabajo/fisiología , Adulto , Animales , Fenómenos Biomecánicos , Codo/fisiología , Electromiografía , Antebrazo , Fuerza de la Mano/fisiología , Humanos , Masculino , Modelos Animales , Fatiga Muscular/fisiología , Fuerza Muscular/fisiología , Músculo Esquelético , Porcinos , Análisis y Desempeño de Tareas , TorqueRESUMEN
Headless compression screws (HCSs) are commonly used to fixate small bones and articular fractures. Understanding the biomechanical efficacy of different HCS designs can help surgeons make proper interfragmentary compression when a specific implant is chosen. HCSs with three different central shaft designs (unthreaded, fully threaded, and partially threaded) were studied: the Herbert-Whipple, Mini-Acutrak 2, and headless reduction (HLR). Polyurethane foam blocks were machined with a simulated fracture gap of 0.5 mm and set onto a custom-made jig to simultaneously measure compression force and driving torque during screw insertion. The maximal achievable compression forces and driving torques recorded were 47.4 ± 0.9 N and 145.11 ± 1.65 N mm for the HLR, 50.98 ± 1.29 N and 152.62 ± 2.83 N mm for the Mini-Acutrak 2, and 19.33 ± 1.0 N and 33.4 ± 2.2 N mm for the Herbert-Whipple. Overall, the compression force of the Mini-Acutrak 2 and HLR increased with the torque. Unlike the other screws, the Herbert-Whipple's driving torque increased while the compression force decreased after peak compression force was achieved. The partially threaded shaft design (HLR) demonstrated equivalent biomechanical advantage with the Mini-Acutrak 2 in interfragmentary compression. The HCSs with cone-shaped proximal ends (HLR and Mini-Acutrak 2) maintained their compression force during over-fastening, whereas the unthreaded central shaft of the Herbert-Whipple screw caused it to lose compression force.
Asunto(s)
Tornillos Óseos , Simulación por Computador , Fijación Interna de Fracturas/métodos , Fracturas Óseas/cirugía , Fracturas Intraarticulares/cirugía , Fenómenos Biomecánicos , Humanos , Poliuretanos , PresiónRESUMEN
OBJECTIVE: The purpose of this study was to evaluate the mechanical performance of mini-screws during insertion into artificial bone with use of the driving torque tester (Biomaterials Korea, Seoul, Korea), as well as testing of Pull-out Strength (POS). METHODS: Experimental bone blocks with different cortical bone thickness were used as specimens. Three modules of commercially available drill-free type mini-screws (Type A; pure cylindrical type, Biomaterials Korea, Seoul, Korea, Type B; partially cylindrical type, Jeil Medical, Seoul, Korea, Type C; combination type of cylindrical and tapered portions, Ortholution, Seoul, Korea), were used. RESULTS: Difference in the cortical bone thickness had little effect on the maximum insertion torque (MIT) in Type A mini-screws. But in Type B and C, MIT increased as the cortical bone thickness increased. MIT of Type C was highest in all situations, then Type B and Type A in order. Type C showed lower POS than Type A or B in all situations. There were statistically significant correlations between cortical bone thickness and MIT, and POS for each type of the mini-screws. CONCLUSION: Since different screw designs showed different insertion torques with increases in cortical bone thickness, the best suitable screw design should be selected according to the different cortical thicknesses at the implant sites