RESUMEN

The addition of Co to Ni-based alloys can reduce the stacking fault energy. In this study, a novel Ni-26.6Co-18.4Cr-4.1Mo-2.3Al-0.3Ti-5.4Nb alloy was developed by increasing the Co addition to 26.6 wt.%. A new strategy to break the trade-off between strength and ductility is proposed by introducing dense nanosized precipitations, stacking faults, and nanoscale twins in the as-prepared alloys. The typical characteristics of the deformed alloy include dense dislocations tangles, nanotwins, stacking faults, and Lomer-Cottrell locks. In addition to the pinning effect of the bulky δ precipitates to the grain boundaries, the nanosized γ' particles with a coherent interface with the matrix show significant precipitation strengthening. As a result, the alloy exhibits a superior combination of yield strength of 1093 MPa and ductility of 29%. At 700 °C, the alloy has a high yield strength of 833 MPa and an ultimate tensile strength of 1024 MPa, while retaining a ductility of 6.3%.

RESUMEN

The commonly used aluminum-copper alloys in industry are mainly rolled plates and extruded or drawn bars. The aluminum-copper alloys' anisotropy generated in the manufacturing process is unfavorable for subsequent applications. Its underlying mechanism shall be interpreted from a microscopic perspective. This paper conducted the loading simulation on Al-4%Cu alloy crystals at the microscopic scale with molecular dynamics technology. Uniaxial tension and compression loading were carried out along three orientations: X-<1¯12>, Y-<11¯1>, and Z-<110>. It analyzes the micro-mechanisms that affect the performance changes of aluminum-copper alloys through the combination of stress-strain curves and different organizational analysis approaches. As shown by the results, the elastic modulus and yield strength are the highest under tension along the <11¯1> direction. Such is the case for the reasons below: The close-packed plane of atoms ensures large atomic binding forces. In addition, the Stair-rod dislocation forms a Lomer-Cottrell dislocation lock, which has a strengthening effect on the material. The elastic modulus and yield strength are the smallest under tension along the <110> direction, and the periodic arrangement of HCP atom stacking faults serves as the main deformation mechanism. This is because the atomic arrangement on the <110> plane is relatively loose, which tends to cause atomic misalignment. When compressed in different directions, the plastic deformation mechanism is mainly dominated by dislocations and stacking faults. When compressed along the <110> direction, it has a relatively high dislocation density and the maximum yield strength. That should be attributed to the facts below. As the atomic arrangement of the <110> plane itself was not dense originally, compression loading would cause an increasingly tighter arrangement. In such a case, the stress could only be released through dislocations. This research aims to provide a reference for optimizing the processing technology and preparation methods of aluminum-copper alloy materials.

RESUMEN

Single Recovery Roadway (SRR) is a novel retraction technology in the non-pillars mining innovation system. In previous support withdrawing, single recovery roadway was usually replaced by a dual-recovery roadway or cut the coal wall before the support. This study is set against the background of the longwall panel at Duanshi Coal Mine, where a mechanical model based on the stress characteristics of a composite cantilever beam was constructed to analyze the failure of the main roof in a single recovery roadway. Through numerical analysis, the relationship between deformation failure of the recovery roadway and interlayer slippage structures was explored, as well as how mining-induced stress distribution and the evolution of key strata fractures impact the stability of the roadway. The results indicate that after the connection of the longwall panel and the recovery roadway, the overlying composite interlayered rock strata are affected by the interlayer slippage structures, leading to significant asymmetric deformation in the surrounding rocks. Additionally, borehole observation data support the theoretical calculations of the cantilever beam model. These research results enhance the understanding of the interlayer slip instability mechanism and provide important guidance for mine design under similar geological conditions.

RESUMEN

The Three Gorges Reservoir Area (TGRA) is characterized by unique geological features that increase its susceptibility to landslides. These slopes are especially prone to destabilization when influenced by external triggers like rainfall. This research focuses on the Piansongshu landslide within the TGRA, aiming at unraveling the complex internal deformation mechanisms of landslides triggered by rainfall and providing critical insights for their prevention and mitigation. The study begins with on-site geological surveys to meticulously examine the macroscopic signs and mechanisms of deformation. It then utilizes the GeoStudio numerical simulation software to assess the landslide's stability, focusing on the changes in internal seepage fields and stability under various rainfall scenarios. Results indicate that continuous rainfall leads to the formation of a temporary saturation zone on the slope, which gradually deepens. In regions with more pronounced deformation, the infiltration line at the leading edge of accumulation notably protrudes towards the surface. Notably, the stability coefficient of the secondary shear surface of the landslide fluctuates more significantly than that of the primary sliding surface. Higher rainfall intensity and longer duration are positively correlated with a more pronounced decrease in stability coefficients. The impact on stability also varies across different rainfall patterns. As rainfall infiltrates over time, the slope's safety factor gradually decreases. This reduction continues even post-rainfall, indicating a delayed restoration period before stability returns to a safe level. These results yield valuable data for forecasting and mitigating landslides.

RESUMEN

Thin-walled bearings are widely used owing to the advantages of their light structure, high hardness, and strong load-carrying capacity. However, thin-walled bearings are often prone to deformation during the machining process, which can seriously affect the performance of the bearings. In addition, the machining deformation and quality of bearings are difficult to balance. To address the above issues, this paper investigates the effects of the machining parameters on the machining deformation, surface quality, and machining efficiency of a thin-walled bearing during the roughing stage. The dynamic balance between deformation inhibition and high quality in rough grinding was studied, and the optimal parameters for thin-walled bearing outer ring grinding were obtained. The deformation mechanism of thin-walled bearings caused by grinding was revealed through simulation and experimental analysis. The results show that the machining deformation and quality reach a balance when the workpiece speed is 55 r/min, the grinding wheel rotational speed is 2000 r/min, and the feed rate is 0.1 mm/min. Deformation increases with the increase in workpiece speed and grinding wheel speed. At the same time, the surface roughness increases with the increase in the workpiece speed, but the increase in the wheel speed will improve the surface roughness. As the workpiece speed increases, the surface topography shows a more pronounced stockpile of material, which is ameliorated by an increase in grinding wheel speed. As the rotational speed of the workpiece increases, the number of abrasive grains involved in the process per unit of time decreases, and the surface removal of the workpiece is less effective, while the increase in the rotational speed of the grinding wheel has the opposite effect. The grinding deformation of thin-walled bearings is mainly induced by machining heat and stress. As the rotational speed increases, the heat flux in the grinding zone increases. More heat flux flows into the surface of the workpiece, causing an increase in thermal stresses on the inner surface of the bearing collar, leading to greater deformation. The temperature in the grinding area can be reduced during machining, realizing a reduction in deformation. The research content contributes to the balance between high quality and low distortion in machining processes.

RESUMEN

In this work, we consider the physical basis of deformation and fracture in layered composite nanocrystalline/amorphous material-low-melting crystalline alloy in a wide temperature range. Deformation and fracture at the crack tip on the boundary of such materials as nanocrystalline alloy of the trademark 5BDSR, amorphous alloy of the trademark 82K3XSR and low-melting crystalline alloy were experimentally investigated. The crack was initiated by uniaxial stretching in a temperature range of 77-293 K. A theoretical description of the processes of deformation and fracture at the crack tip is proposed, with the assumption that these processes lead to local heating and ensure the plastic character of crack growth at liquid nitrogen temperatures. The obtained results improve the theoretical understanding of the physics of fracture at the boundary of nanocrystalline and crystalline alloys in a wide temperature range. The possibility of preserving the plastic nature of fracture in a thin boundary layer of crystalline-nanocrystalline material at cryogenic temperatures has been experimentally shown.

RESUMEN

Using the Split Hopkinson Pressure Bar technique, strain-limited dynamic compressive loading experiments were performed on TA1/TA15 heterostructure (HS) materials. The plastic deformation mechanisms, fracture forms, and energy absorption properties of an HS material with a metallurgical bonding interface (MB) and an HS material without a metallurgical bonding interface (NMB) are compared and analyzed. The results show that there is no significant difference between the two deformation mechanisms. The fracture forms are all "V-shaped" fractures within the TA1 part. The NMB was carried for 57 µs before failure and absorbed 441 J/cm3 of energy. The MB was carried for 72 µs before failure and absorbed 495 J/cm3 of energy. Microstructure observations show that there is a coordinated deformation effect near the MB interface compared to the NMB, with both TA1 and TA15 near the interface carrying stresses. This causes an enhancement of the MB load-bearing time and a 12% increase in energy absorption.

RESUMEN

This study investigates the viscoelastic deformation mechanisms of bone as a response to Vickers hardness indentation. We utilized advanced high-resolution scanning electron microscopy (SEM) to investigate a distinct deformation pattern that originates from the indentation site within the bone matrix. The focus of our research was to analyze a unique deformation mechanism observed in bone tissue, which has been colloquially termed as "screw-like" due to its resemblance to a screw thread when viewed under an optical microscope. The primary goals of this research are to investigate the distinctive characteristics of the "screw-like" deformation pattern and to determine how the microstructure of bone influences the initiation and control of this mechanism. These patterns, emerging during the dwell period of indentation, underscore the viscoelastic nature of bone, indicating its propensity for energy dissipation and microstructural reconfiguration under load. This study uncovered a direct correlation between the length of the "screw-like" deformation and the duration of the indentation dwell time, providing quantifiable evidence of the bone's viscoelastic behavior. This finding is pivotal in understanding the mechanical properties of bone, including its fracture toughness, as it relates to the complex interplay of factors such as energy dissipation, microstructural reinforcement, and stress distribution. Furthermore, this study discusses the implications of viscoelastic properties on the bone's ability to resist mechanical challenges, underscoring the significance of viscoelasticity in bone research.

RESUMEN

Heat treatment is an important process for optimizing the microstructures of superalloys, and the cooling rate after solid solution treatment is one of the most critical parameters. In this work, we treated solid solution MAR-M247 alloys with water quenching, air cooling, and furnace cooling. Microstructure characterization, hardness, and room temperature tensile tests were conducted to investigate the effect of cooling rate on the microstructure and mechanical properties of MAR-M247 alloys. The results showed that the cooling rate after solid solution treatment mainly affected the precipitation behavior of the secondary γ' phase, but it had few effects on other microstructure characterizations, including grain size, γ/γ' eutectic, and MC carbide. The water-quenched sample had the highest cooling rate (400 °C/s) and hardness (400 HV) but suffered from premature fracture because of quenching cracks. A further decrease in cooling rate from 1.5 °C/s to 0.1 °C/s deteriorated hardness (384 HV to 364 HV) and yield strength (960 MPa to 771 MPa) but increased elongation (8.5% to 13.5%). Moreover, the deformation mechanism was transformed from dislocation shearing to Orowan bypassing. The decreased yield strength was mainly due to the weakened precipitation strengthening resulting from γ'-phase coarsening. The improved elongation was attributed to not only the higher work-hardening index caused by interface dislocation networks but also the more uniform deformation, which delayed necking.

RESUMEN

This study investigates how deviation angles close to the [001] orientation affect the tensile properties and deformation behavior of a nickel-based single-crystal superalloy at room temperature. The research focuses on samples with deviation angles of 3°, 8°, and 13° from the [001] orientation and examines their strength and ductility. We employed scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM) to explore the deformation micro-mechanisms at varying angles. Findings reveal that strength decreases and ductility increases as the deviation angle widens within the [001] vicinity. The study emphasizes that <110> octahedral slip-driven crystal slip and rotation are crucial for understanding tensile deformation. The deformation differences in samples at varying angles are attributed to the differential engagement of mechanisms. Specifically, at lower angles, reduced ductility and increased strength are due to short lattice rotation paths and work hardening causing superlattice stacking faults (SSFs) to slip in two directions on the {111} plane within the γ' phase. As the angles increase, the lattice rotation paths extend, and Shockley partial dislocations (a/6<112>) accumulate in γ channels. This process, involving SSFs moving in a single direction within the γ' phase, results in higher ductility and reduced strength.

RESUMEN

Upon tensile stress, the spiral cellulose fibrils in wood cell walls rotate like springs with decreasing microfibril angle (MFA), and the cellulose molecules elongate in the chain direction. Compression wood with high MFA and opposite wood with low MFA were comparatively studied by in-situ tensile tests combined with synchrotron radiation WAXS in the present study. FTIR spectroscopy revealed that compression wood had a higher lignin content and fewer acetyl groups. For both types of wood, the lattice spacing d004 increased and the MFA decreased gradually with the increase of tensile stress. At stresses beyond the yield point, cellulose lattice strain depended linearly on macroscopic stress, while the MFA depended linearly on macroscopic strain. The deformation mechanisms of compression wood and opposite wood are not essentially different but differ in their deformation behavior. Specifically, the contribution ratio of lattice strain and cellulose fibril reorientation to macroscopic strain was 0.25 and 0.53 for compression wood, and 0.40 and 0.33 for opposite wood, respectively. Due to the geometric effects of MFA, a greater contribution of cellulose fibril reorientation to the macroscopic deformation was detected in compression wood than in opposite wood.

Asunto(s)

RESUMEN

The planned viaduct in Jining, Shandong is a priority project in the city. However, the 63 working faces of a mine in Jining is only 3 m away from the planned viaduct, posing a serious threat to the safety of the viaduct's construction. Consequently, it is essential to evaluate the stability of the planned viaduct's goaf area under the influence of the 63 working faces. However, the 63 working faces are short faces, and there is a lack of corresponding prediction of surface residual subsidence. To address this issue, this paper employs theoretical analysis and numerical simulation to uncover the foundation deformation mechanism and characteristics of fractured rock and soil mass in the short goaf. Subsequently, a residual subsidence prediction method for the short goaf was proposed for the viaduct mined-out area. This new approach was implemented for the planned viaduct in Jining, and its effectiveness was validated through InSAR and leveling monitoring results. The research findings offer technical support for viaduct construction in areas affected by underground mining.

Asunto(s)

RESUMEN

Understanding plastic deformation behaviour is key to optimising the mechanical properties of nano-polycrystalline layered composites. This study employs the molecular dynamics (MD) simulation to comprehensively investigate the effects of various factors, such as grain sizes, strain rates, and the interlayer thicknesses of the intermetallic compounds (IMCs), on the plastic deformation behaviour of nano-polycrystalline Al/Mg layered composites. Our findings reveal that the influence of grain size on deformation behaviour is governed by the strain rate, and an increase in grain size is inversely proportional to yield stress at low strain rates, whereas it is positively proportional to tensile stress at high strain rates. Moreover, an optimal thickness of the intermediate layer contributes to enhanced composite strength, whereas an excessive thickness leads to reduced tensile strength due to the fewer grain boundaries (GBs) available for accommodating dislocations. The reinforcing impact of the intermediate IMCs layer diminishes at excessive strain rates, as the grains struggle to accommodate substantial large strains within a limited timeframe encountered at high strain rates. The insights into grain sizes, strain rates, and interlayer thicknesses obtained from this study enable the tailored development of nanocomposites with optimal mechanical characteristics.

RESUMEN

In this work, a Mg-Zn-Y (ZW31) alloy with good plasticity was introduced into 10 µm 10 vol% SiCp/AZ91 composite materials (PMMCs) via the extrusion compound method, and then the ZW31/PMMC laminate was prepared via multi-pass hot rolling. The hot deformation mechanism and elevated temperature tensile fracture mechanism of ZW31/PMMC laminates were studied using the elevated temperature tensile test. The elevated temperature deformation mechanism is influenced by the strain rate. At low strain rates, grain boundary slip is the primary elevated temperature deformation mechanism of the ZW31/PMMC laminate. However, at high strain rates, the activation of pipeline diffusion is facilitated by the particle deformation zone (PDZ) in the PMMC layer with a high dislocation density, leading to the dominance of dislocation climbing as the main mechanism for elevated temperature deformation of the laminate. Additionally, the implementation of a ZW31/PMMC laminate structure effectively inhibits the initiation and propagation of cavities and microcracks within the laminate layer along the normal direction (ND) while simultaneously blunting crack tips via lattice dislocation emission toward the ZW31 layer. Upon cracking of the PMMC layer, stress concentration occurs in the fracture area of the ZW31 layer, ultimately resulting in necking-induced detachment.

RESUMEN

Material deformation during nanoimprinting of aluminum (Al), copper (Cu), and gold (Au) was explored through molecular dynamics simulations. A comparative understanding of the deformation behavior of three substrate materials important for design and high-resolution pattern transfer was highlighted. In this study, we analyzed three metrics, including von Mises stresses, lattice deformation, and spring-back for the chosen materials. Of the three materials, the highest average von Mises stress of 7.80 MPa was recorded for copper, while the lowest value of 4.68 MPa was computed for the gold substrate. Relatively higher von Mises stress was observed for all three materials during the mold penetration stages; however, there was a significant reduction during the mold relaxation and retrieval stages. The Polyhedral Template Matching (PTM) method was adopted for studying the lattice dislocation of the materials. Predominantly Body-Centered Cubic (BCC) structures were observed during the deformation process and the materials regained more than 50% of their original Face-Centered Cubic (FCC) structures after mold retrieval. Gold had the lowest vertical spring-back at 6.54%, whereas aluminum had the highest average spring-back at 24.5%. Of the three materials, aluminum had the lowest imprint quality due to its irregular imprint geometry and low indentation depth after the NIL process. The findings of this research lay a foundation for the design and manufacture of Nanoimprint Lithography (NIL) molds for different applications while ensuring that the replicated structures meet the desired specifications and quality standards.

RESUMEN

This study investigates the microstructures and deformation mechanism of hetero-structured pure Ti under different high strain rates (500 s-1, 1000 s-1, 2000 s-1). It has been observed that, in samples subjected to deformation, the changes in texture are minimal and the rise in temperature is relatively low. Therefore, the influence of these two factors on the deformation mechanism can be disregarded. As the strain rate increases, the dominance of dislocation slip decreases while deformation twinning becomes more prominent. Notably, at a strain rate of 2000 s-1, nanoscale twin lamellae are activated within the grain with a size of 500 nm, which is a rarely observed phenomenon in pure Ti. Additionally, martensitic phase transformation has also been identified. In order to establish a correlation between the stress required for twinning and the grain size, a modified Hall-Petch model is proposed, with the obtained value of Ktwin serving as an effective metric for this relationship. These findings greatly enhance our understanding of the mechanical responses of Ti and broaden the potential applications of Ti in dynamic deformation scenarios.

RESUMEN

Semicrystalline polymers are lightweight, multiphase materials that exhibit attractive shock dissipation characteristics and have potential applications as protective armor for people and equipment. For shocks of 10 GPa or less, we analyzed various mechanisms for the storage and dissipation of shock wave energy in a realistic, united atom (UA) model of semicrystalline polyethylene. Systems characterized by different levels of crystallinity were simulated using equilibrium molecular dynamics with a Hugoniostat to ensure that the resulting states conform to the Rankine-Hugoniot conditions. To determine the role of structural rearrangements, order parameters and configuration time series were collected during the course of the shock simulations. We conclude that the major mechanisms responsible for the storage and dissipation of shock energy in semicrystalline polyethylene are those associated with plastic deformation and melting of the crystalline domain. For this UA model, plastic deformation occurs primarily through fine crystallographic slip and the formation of kink bands, whose long period decreases with increasing shock pressure.

RESUMEN

U-Mo alloys were considered to be the most promising candidates for high-density nuclear fuel. The uniaxial tensile behavior of nanocrystalline U-10Mo alloys with average grain sizes of 8-23 nm was systematically studied by molecular dynamics (MD) simulation, mainly focusing on the influence of average grain size on the mechanical properties and deformation mechanisms. The results show that Young's modulus, yield strength and ultimate tensile strength follow as average grain size increases. During the deformation process, localized phase transitions were observed in samples. Grain boundary sliding and grain rotation, as well as twinning, dominated the deformation in the smaller and larger grain sizes samples, respectively. Increased grain size led to greater localized shear deformation, resulting in greater stress drop. Additionally, we elucidated the effects of temperature and strain rate on tensile behavior and found that lower temperatures and higher strain rates not only facilitated the twinning tendency but also favored the occurrence of phase transitions in samples. Results from this research could provide guidance for the design and optimization of U-10Mo alloys materials.

RESUMEN

The present study investigates the creep behavior and deformation mechanism of a third-generation single-crystal Ni-based superalloy at 1170 °C under a range of stress levels. Scanning electron microscopes (SEM) and transmission electron microscopes (TEM) were employed to observe the formation of a rafted γ' phase, which exhibits a topologically close-packed (TCP) structure. The orientation relationship and elemental composition of the TCP phase and matrix were analyzed to discern their impact on the creep properties of the alloy. The primary deformation mechanism of the examined alloy was identified as dislocation slipping within the γ matrix, accompanied by the climbing of dislocations over the rafted γ' phase during the initial stage of creep. In the later stages of creep, super-dislocations with Burgers vectors of a<010> and a/2<110> were observed to shear into the γ' phase, originating from interfacial dislocation networks. Up to the fracture, the sequential activation of dislocation shearing in the primary and secondary slipping systems of the γ' phase occurs. As a consequence of this alternating dislocation shearing, a twist deformation of the rafted γ' phase ensued, ultimately contributing to the fracture mechanism observed in the alloy during creep.

RESUMEN

Equiatomic CoCrNi medium-entropy alloys exhibit superior strength and ductility. In this work, a non-equiatomic CoCrNi alloy with low stacking fault energy was designed, and different fractions of V were added to control the stacking fault energy and lattice distortion. Mechanical properties were evaluated by tensile tests, and deformation microstructures were characterized by transmission electron microscope (TEM). The main deformation mechanisms of CoCrNiV alloy with low V content are dislocation slip, stacking faults, and deformation-induced HCP phase transformation, while the dominant deformation patterns of CoCrNiV alloy with high V contents are dislocation slip and stacking faults. The yield strength increases dramatically when the V content is high, and the strain-hardening behavior changes non-monotonically with increasing the V content. V addition increases the stacking fault energy (SFE) and lattice distortion. The lower strain-hardening rate of 6V alloy than that of 2V alloy is dominated by the SFE. The higher strain-hardening rate of 10V alloy than that of 6V alloy is dominated by the lattice distortion. The effects of V addition on the SFE, lattice distortion, and strain-hardening behavior are discussed.