RESUMEN

Hexavalent chromium (CrVI) poses a serious risk to both human and environment health. Hence, a simple, robust, and efficient analytical method must be developed to monitor the presence of Cr(VI) in the environment. The current investigation concentrated on the colorimetric detection of Cr(VI) using TMB as indicator in the presence of H2O2. The study found that Cr(VI) reacts with H2O2 to generate hydroxyl radicals which oxidize TMB in a concentration dependent manner. Under optimized conditions, the method obtained a good linearity range (0.025-0.5 mg/L, r2 = 0.9944) with LOD and LOQ of 0.009 mg/L and 0.029 mg/L, respectively. The technique was further improved by the addition of EDTA in the sample preparation protocol to reduce the false positive result by the presence of ions like Cu2+, Fe3+, etc. The study recorded improved Cr(VI) recoveries (81.73-111.40 %) at different fortification levels (0.1-0.5 mg/L). Under optimized conditions, the EDTA added method obtained a good linear response (r2 = 0.9952) with a detection limit of 0.023 mg/L which is less than the prescribed limits by WHO (0.05 mg/L) and US EPA (0.1 mg/L) for drinking water. The developed analytical method is very simple without use of any nanomaterial and the results with natural water samples show that it has the potential for real-time detection of Cr(VI) in the environment.

RESUMEN

Bioremediation, an economical and environmentally friendly approach, provides a sustainable solution for mitigating heavy metal contamination in soils. This study identifies four fungal strains-Trichoderma harzianum DAA8, Trichoderma reesei DAA9, Rhizomucor variabilis DFB3, and Trichoderma asperellum LDA4-that exhibit tolerance to cadmium (Cd) and chromium (Cr). These strains were isolated from soils impacted by heavy metal contamination in mining regions. Rigorous examinations of these strains led us to determine their Minimum Inhibitory Concentrations (MICs) and optimal absorption-reduction conditions. Our microscopic data and GC-MS analysis indicate that these strains can accumulate Cd and Cr by generating compounds, such as ketones and imines, in heavy metal environments. We evaluated the remediation efficacy of both single and co-cultures of Rhizomucor variabilis DFB3 and Trichoderma asperellum LDA4 in conjunction with king grass, a plant known for its heavy metal accumulation capabilities. Our findings indicated an impressive 41.9% increase in plant biomass and 47.2% and 64.4% increase in Cd and Cr accumulation respectively. The removal rates of Cd and Cr were 16.5% and 19.0%, respectively, following the co-inoculation of Rhizomucor variabilis DFB3 and Trichoderma asperellum LDA4. These rates represent increases of 37.1% and 33.7% compared to the removal rates achieved with king grass alone. This study not only advances strategies to manage Cd-Cr contamination but also sets a pathway for efficient heavy metal soil remediation using a microbial-plant combined technique.

RESUMEN

In this study, a new and simple glassy carbon electrode modified with carbon nanohorns (SWCNH/GCE) was used for the determination of Cr(VI) in aqueous matrices via adsorptive cathodic stripping voltammetry (AdCSV). The modified electrode was characterized via field emission scanning electron microscopy and cyclic voltammetry, which revealed a homogeneous distribution of spherical agglomerates of SWCNH on the electrode surface. The modification increased the electrochemically active area from 0.10 cm2 ± 0.01 (GCE) to 0.16 cm2 ± 0.01 (SWCNH/GCE). The optimized analytical conditions were as follows: a supporting electrolyte (0.15 mol L-1 HCl), an accumulation potential of 0.8 V versus Ag/AgCl, and an accumulation time of 240 s. Validation of the analytical methodology was performed, obtaining a linear range between 20 and 100 µg L-1, a limit of detection of 3.5 µg L-1, and a limit of quantification of 11.6 µg L-1 with good accuracy and precision. The method was applied to the analysis of spiked tap water samples, and the results were compared using a flame atomic absorption spectrophotometer (FAAS) with no significant statistical differences.

RESUMEN

The production of keratinases was evaluated in submerged fermentation with Aspergillus niger and by pigs' swine hair in a batch bioreactor. Experimental planning was performed to assess the interaction between different variables. The enzyme extract produced was characterized at various pH and temperatures and subjected to enzyme concentration using a biphasic aqueous system and salt/solvent precipitation techniques. In addition, the substrate's potential in reducing hexavalent chromium from synthetic potassium dichromate effluent with an initial concentration of 20 mg L-1 of chromium was evaluated. The resulting enzyme extract showed 89 ± 2 U mL-1 of keratinase. The enzyme concentration resulted in a purification factor of 1.3, while sodium chloride/acetone and ammonium sulfate/acetone resulted in a purification factor of 1.9 and 1.4, respectively. Still using the residual substrate of swine hair from the fermentation, a 94% reduction of hexavalent chromium concentration occurred after 9 h of reaction. Thus, the study proved relevant for producing keratinases, with further environmental applicability and the possibility of concentrating the extract via low-cost processes.

RESUMEN

Studies on the molecular mechanisms of heavy metal toxicity in invertebrate reproduction are limited. Given that PARP-catalysed ADP-ribosylation is also involved in counteracting heavy metal toxicity and maintaining genomic integrity, and that PARylation is implicated in chromatin remodelling but its role in sperm chromatin remains to be elucidated, we investigated the effects of chromium(VI) at 1, 10 and 100 nM on the reproductive health of Mytilus galloprovincialis. The damage to the gonads was assessed by morphological analyses and the damage indices PARP and É£H2A.X were measured. Changes in the binding of protamine-like (PL) to DNA and the possibility of poly(ADP-ribosyl)ation of PL proteins were also investigated. Gonadal chromium accumulation and morphological damage were found, especially when the mussels were exposed to the highest dose of chromium(VI). In addition, the maximum expression of gonadal É£H2A.X and PARP were obtained at 100 and 10 nM Cr(VI), respectively. Interestingly, for the first time in all exposed conditions, poly(ADP)-ribosylation was detected on PL-II, which, together with PL-III and PL-IV, are the major nuclear basic proteins of Mytilus galloprovincialis sperm chromatin. Since PL-II is involved in the final high level of sperm chromatin compaction, this post-translational modification altered the binding of the PL protein to DNA, favouring the action of micrococcal nuclease on sperm chromatin. This study provides new insights into the effects of chromium(VI) on Mytilus galloprovincialis reproductive system and proposes a molecular mechanism hypothesis describing the toxic effects of this metal on PL-DNA binding, sperm chromatin and gonads.

Asunto(s)

RESUMEN

In this study, the ionic liquid (IL) trioctylmethylammonium salicylate (TOMAS) was prepared and incorporated into a polymer inclusion membrane (PIM) based on cellulose triacetate (CTA) as the polymer for the removal of Cr(VI). Various parameters including the effect of membrane composition (plasticizer and carrier concentration) as well as variables affecting both the feed phase and receiving solution have been investigated. Optimal results were achieved with a PIM made of 50% CTA and 50% TOMAS (% in mass) without the addition of any plasticizer. Using this PIM, Cr(VI) was effectively transported from a feed solution consisting of 10 mg L-1 Cr(VI) in 0.01 mol L-1 NaNO3 at pH = 2, to a receiving solution containing 0.1 mol L-1 NaOH. The transport of Cr(VI) was not affected by the presence of other metals, such as Cr(III), Cd(II), Zn(II), Cu(II), and Ni(II), and a selective recovery rate of 93.61% for both single-ion and mixed-ion solutions after 24 h of processing was obtained. Finally, the stability of the membrane was also investigated, with a slight decrease in efficiency observed after 5 days of reuse.

Asunto(s)

RESUMEN

Magnetite nanoparticles (nano-Fe3O4) and nano-Fe3O4 immobilized with bacterial extracellular polymeric substances (EPSs) extracted from Lysinibacillus sp. WH (Fe3O4/bact) were comparatively studied for the removal of Cr (VI) ions from aqueous solution in batch study. The objectives were to explore the removal of Cr (VI) efficiency by nano-Fe3O4 and Fe3O4/bact under varying bacterial concentrations at a range of acidic pH. Results indicated that 150 ppm Cr (VI) could be effectively removed by 5 g/L of nano-Fe3O4 at pH 4, with the efficiency of 89.2 ± 12%. The equilibrium time, determined by a pseudo-second-order model (R2 = 0.9983), was after 5 h, indicating chemical adsorption. The Cr (VI) removal by the nano-Fe3O4 immobilized with bacterial EPS was effective and steady under a wide range of acidic conditions although bacterial EPS has an alkaline nature. Here, we are the first to demonstrate that Cr (VI) removal efficiency by different concentrations of EPS was not significantly different, suggesting EPS concentration is possibly not the most crucial factor to be optimized for Cr (VI) removal in the future. This study shows the potential application of nano-Fe3O4 immobilized with bacterial EPS for wastewater treatment. PRACTITIONER POINTS: The equilibrium time for magnetite nanoparticles to remove Cr (VI) is 5 h, suggesting chemical adsorption. The Cr (VI) removal efficiency of either magnetite nanoparticles or bacterial EPS is stable under a wide range of acidic conditions. Magnetite nanoparticles immobilized with bacterial EPS extracted from Lysinibacillus sp. WH has a potential application for Cr (VI) removal in wastewater.

Asunto(s)

RESUMEN

The development of effective photocatalysts for the reduction of Cr(VI) and the degradation of antibiotics remains a challenge. The present work reports the development of a novel heterojunction composite material, BiOCl/BaTiO3@Co-BDC-MOF (BOC/BTO@Co-MOF), based on solvothermal techniques. To characterize the surface and bulk features of the material, techniques such as FE-SEM, HR-TEM, BET/BJH, XPS, FT-IR, p-XRD, and UV-Vis-DRS were used. Based on the results, the BiOCl/BaTiO3 nanocomposites are uniformly dispersed on the rod-shaped Co-BDC MOF, resulting in a layered texture on the surface. A further advantage of the composite structure is the strong interfacial enhancement facilitating the separation of photoexcited electron-hole pairs. Also, compared to its pristine counterparts, the heterostructure material exhibited excellent surface area and pore properties. The photocatalytic efficiency towards reduction and degradation of Cr(VI)/SMX pollutants were evaluated by optimizing various analytical parameters, such as pH, catalytic loading concentrations, analyte concentration, and scavenger role. The specially designed BOC/BTO@Co-MOF composite achieved a 96.5% Cr(VI) reduction and 98.2% SMX degradation under 60.0-90.0 min of visible light illumination at pH 3.0. This material is highly reusable and has a six-time recycling potential. The findings of this study contribute to a better understanding of the efficient decontamination of inorganic and organic pollutants in water purification systems.

Asunto(s)

RESUMEN

BACKGROUND: In response to growing concerns regarding heavy metal contamination in food, particularly chromium (Cr)(VI) contamination, this study presented a simple, sensitive and practical method for Cr(VI) detection. RESULTS: A magnetic separation-based capture-exponential enrichment ligand system evolution (SELEX) method was used to identify and characterize DNA aptamers with a high affinity for Cr(VI). An aptamer, Cr-15, with a dissociation constant (Kd) of 4.42 ± 0.44 µmol L-1 was obtained after only eight rounds of selection. Further innovative methods combining molecular docking, dynamic simulation and thermodynamic analysis revealed that CrO4 2- could bind to the 19th and 20th guanine bases of Cr-15 via hydrogen bonds. Crucially, a label-free fluorometric aptasensor based on SYBR Green I was successfully constructed to detect CrO4 2-, achieving a linear detection range of 60-300 nmol L-1 with a lower limit of detection of 44.31 nmol L-1. Additionally, this aptasensor was able to quantitatively detect CrO4 2- in grapes and broccoli within 40 min, with spike recovery rates ranging from 89.22% to 108.05%. The designed fluorometric aptasensor exhibited high selectivity and could detect CrO4 2- in real samples without sample processing or target pre-enrichment. CONCLUSION: The aptasensor demonstrated its potential as a reliable tool for monitoring Cr(VI) contamination in fruit and vegetable products. © 2024 Society of Chemical Industry.

RESUMEN

The increasing water contamination by toxic heavy metals, particularly hexavalent chromium, has become a significant environmental concern. This study explores the pyrolysis of termite-processed biomass, specifically Pinus elliottii particleboard and its termite droppings (TDs), to produce biochar and its application for chromium (VI) adsorption. Termite droppings, rich in lignin, and particleboard, rich in cellulose, were pyrolyzed at various temperatures to assess the effect of biomass composition on biochar properties. The study found that lignin-rich termite droppings produced biochar with higher fixed carbon content and specific surface area than cellulose-rich particleboard biochar. FTIR and Raman spectroscopy revealed significant molecular structure changes during pyrolysis, which influenced the adsorption capabilities of the biochar. Adsorption experiments demonstrated that TD biochar exhibited significantly higher chromium (VI) adsorption capacity, attributed to its distinct chemical composition and enhanced surface properties due to higher lignin content. These findings underscore the crucial role of lignin in producing efficient biochar for heavy metal adsorption, highlighting the practical applicability of termite-processed biomass in water purification technologies.

Asunto(s)

RESUMEN

The removal of chromium(VI) from an acidic (HCl) medium through non-dispersive extraction with strip dispersion (NDXSD) was investigated using a microporous PVDF membrane support in a permeation cell. The ionic liquid Cyphos IL102 (phosphonium salt) in Solvesso 100 was used as an organic phase. In NDXSD, the stripping phase (NaOH) is dispersed in the organic phase on the cell side with an impeller stirrer adequate to form a strip dispersion. This pseudo-emulsion phase (organic + strip solutions) provides a constant supply of the Cyphos IL102/Solvesso 100 to the membrane phase. Various hydrodynamic and chemical parameters, such as variation in the feed and pseudo-emulsion stirring speeds, HCl and Cr(VI) concentrations in the feed phase, and carrier concentration, were investigated. Results indicated that the best chromium(VI) transport was obtained under the following conditions: feed and pseudo-emulsion stirring speeds of 1000 min-1 and 600 min-1, respectively; an HCl concentration in the feed phase of 0.1 M; a chromium concentration of 0.01 g/L in the same phase; and carrier concentration in the organic phase in the 2-5-10% v/v range. From the experimental data, several mass transfer coefficients were estimated: a bulk diffusion coefficient of 3.1·10-7 cm2/s and a diffusion coefficient of 6.1·10-8 cm2/s in the membrane phase and mass transfer coefficients in the feed (5.7·10-3 cm/s) and membrane phases (2.9·10-6 cm/s). The performance of the present system against other ionic liquids and the presence of base metals in the feed phase were investigated.

RESUMEN

HYPOTHESIS: Magnetic particles are widely used in many adsorption and removal processes. Among the many types of magnetic colloids, magnetic Janus particles offer significant possibilities for the effective removal of several components from aqueous solutions. Nevertheless, the synthesis of structures integrating different types of materials requires scalable fabrication processes to overcome the limitations of the available methodologies. Herein, we hypothesized a fabrication process for dual-surface functionalized magnetic Janus particles. EXPERIMENTS: The primary silica particles with surface-attached amine groups are further asymmetrically modified by iron oxide nanoparticles, exploiting Pickering emulsion and electroless deposition techniques. The dual surface functionality of the particles is designed for its versatility and demonstrated in two wastewater-related applications. FINDINGS: We show that our design can simultaneously remove chromium (VI) and phenol from aqueous solution. The fabricated magnetic-responsive Janus particles are also an effective adsorbent for genomic Deoxyribonucleic acid (DNA) and show superior performance to commercial magnetic beads. Thus, this study provides a novel platform for designing magnetic Janus particles with multifunctional surfaces for wastewater treatment applications.

RESUMEN

Water scarcity is a significant global issue caused by the prolonged disregard and unsustainable management of this essential resource by both public and private bodies. The dependence on fossil fuels further exacerbates society's bleak environmental conditions. Therefore, it is crucial to explore alternative solutions to preserve our nation's water resources properly and promote the production of biofuels. Research into the utilization of E. crassipes to remove heavy metals and generate biofuels is extensive. The combination of these two lines of inquiry presents an excellent opportunity to achieve sustainable development goals. This study aims to develop a sustainable wastewater treatment system and generate biohydrogen from dry, pulverized E. crassipes biomass. A treatment system was implemented to treat 1 L of industrial waste. The interconnected compartment system was built by utilizing recycled PET bottles to generate biohydrogen by reusing the feedstock for the treatment process. The production of biological hydrogen through dark fermentation, using biomass containing heavy metals as a biohydrogen source, was studied. Cr (VI) and Pb (II) levels had a low impact on hydrogen production. The uncontaminated biomass of E. crassipes displayed a significantly higher hydrogen yield (81.7 mL H2/g glucose). The presence of Cr (IV) in E. crassipes leads to a decrease in biohydrogen yield by 14%, and the presence of Pb (II) in E. crassipes leads to a decrease in biohydrogen yield of 26%. This work proposes a strategy that utilizes green technologies to recover and utilize contaminated water. Additionally, it enables the production of bioenergy with high efficiency, indirectly reducing greenhouse gases. This strategy aligns with international programs for the development of a circular economy.

RESUMEN

Environmental and occupational exposure to hexavalent chromium (CrVI) is mostly renowned as a possible hepatotoxic in mammals. Echinacea purpurea (L.) Moench, a phenolic-rich plant, is recurrently used for its therapeutic properties. Therefore, this investigation was done to explore whether E. purpurea (EP) root extract would have any potential health benefits against an acute dose of CrVI-induced oxidative damage and hepatotoxicity. Results revealed that GC-MS analysis of EP root extract has 26 identified components with a significant amount of total phenolic and flavonoid contents. Twenty-four Male Wistar rats were divided into four groups: control, EP (50 mg/kg BW/day for 21 days), CrVI (15 mg/kg BW as a single intraperitoneal dosage), and EP + CrVI, respectively. Rats treated with CrVI displayed a remarkable rise in oxidative stress markers (TBARS, H2O2, PCC), bilirubin, and lactate dehydrogenase activity, and a marked decrease in enzymatic and non-enzymatic antioxidants, transaminases, and alkaline phosphatase activities, and serum protein level. Also, CrVI administration induced apoptosis and inflammation in addition to histological and ultrastructural abnormalities in the liver tissue. The examined parameters were improved significantly in rats pretreated with EP and then intoxicated with CrVI. Conclusively, EP had a potent antioxidant activity and could be used in the modulation of CrVI-induced hepatotoxicity.

Asunto(s)

RESUMEN

In soil, chromium can be found in two main valence forms: hexavalent Cr (VI) and trivalent Cr (III). In terms of toxicity, the most toxic form to plants is Cr (VI). In the present study, we investigated the impact of Cr (VI) (0, 25, 50, 75 and 100 ppm) on growth, physiological parameters and the translocation kinetics of Cr (VI) in the faba bean plant (Vicia faba L.). The results showed that Cr (VI) negatively affects growth parameters (- 15% to - 72%), tolerance index (- 34.05% to - 64.7%), and reduce the total chlorophyll content (until 40%) compared to control plants without Cr (VI). However, the increase of Cr (VI) concentration in the soil, stimulated the synthesis of sugars (max 6,97 mg/g FM), proteins (max 62.89 µg/mg FM) and proline (max 98.57 µg/mg FM) and increased the electrolyte leakage (+ 2.5% to + 9%) compared to control plants. Cr (VI) concentrations in shoots and roots increased significantly for all Cr (VI) doses applied. The translocation factor results showed that the majority of the Cr (VI) absorbed by the plant is stored in the roots, with a very low bioaccumulation factor, which does not exceed 0.4. The findings show that Cr (VI) negatively affects the morpho-physiological parameters of Vicia faba, the bioaccumulation of organic solutes and the low bioaccumulation factor of Cr (VI) can be considered as a strategy of tolerance to Cr(V).

Asunto(s)

RESUMEN

The release of industrial effluents, comprising of organic dyes, antibiotics, and heavy metals poses substantial environmental and ecological threats. Among the different approaches, the utilization of heterogeneous photocatalysis based on semiconducting metal oxides is of paramount important to removal of organic ( MB dye and TC antibiotic) and inorganic pollutants ( Cr (VI) ) in wastewater. In this work, a new approach for creating type-II heterojunction photocatalysts named xNiCo2O4/BiVO4 or BNC is suggested. The as-prepared samples were thoroughly examined by means of several sophisticated analytical tools to investigate their physicochemical properties. These composites were utilized in the decomposition of MB dye, TC drug and the reduction of Cr (VI) under visible light irradiation. According to the findings, the creation of type-II heterojunction at BiVO4-NiCo2O4 interface greatly improved charge transportation while successfully preventing electron-hole recombination. Among the various composites studied, BNC-2 demonstrated an enhanced photocatalytic activity towards degradation of MB and TC, which were found to be 91 % over a period of 150 min and 95 % within only 60 min, respectively. Moreover, the photocatalytic reduction of Cr (VI) was accomplished 96 % within just 25 min. Additionally, it is discovered that BNC-2 displayed promising photostability and recyclability with a retention of >90 % after five consecutive cycles. The enhanced photocatalytic activity of BNC-2 is evidently attributed to the expedited separation and transfer of charges, as proven by photocurrent measurement, photoluminescence and electrochemical impedance spectroscopy analyses. Hence, the current amalgamation of NiCo2O4 and BiVO4 heterojunction composite has paved novel paths towards photocatalytic removal of organic as well as inorganic contaminants.

Asunto(s)

RESUMEN

In this study, we aimed to synthesis of Fe-doping green fluorescent carbon dots (G-CDs) through the co-electrolysis of chrysoidine G and potassium ferrocyanide for Cr(VI) detection. The use of potassium ferrocyanide improves the quantum yield and sensing performance of G-CDs toward Cr(VI). The G-CDs have a maximum excitation wavelength of 308 nm and an emission wavelength of 510 nm. Comprehensive analyses including Raman, FT-IR, and XPS provided insights into the chemical structure and composition of the G-CDs. Under optimal conditions, G-CDs demonstrated concentration-dependent quenching upon interaction with Cr(VI). A linear relationship within the range of 0.25-100 µM was established with a calibration equation of ΔF/F0 = 0.005 + 0.015CCr(VI), yielding an R2 value of 0.996 and a limit of detection of 0.15 µM. The applicability of the G-CDs method was demonstrated by successful Cr(VI) detection in water samples with recovery rates ranging from 98.8 % to 100.1 % and relative standard deviation within 3.0 %. The fluorescence lifetime and Zeta potential measurements confirmed that the mechanism was via a static quenching process, while redox reaction, nanoparticle aggregation, and surface charge variation also played significant roles.

RESUMEN

A new type of polyethyleneimine-protected copper nanoclusters (PEI-CuNCs) is favorably developed by a one-pot method under mild conditions. The obtained PEI-CuNCs is characterized by X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, Fourier-transform infrared (FTIR) spectroscopy and other techniques. It is worth noting that the proposed PEI-CuNCs demonstrate a selective response to chromium(VI) over other competitive species. Fluorescence quenching of PEI-CuNCs is determined to be chromium(VI) concentrations dependence with a low limit of detection of 8.9 nM. What is more, the as-developed PEI-CuNCs is further employed in building a detection platform for portable recognition of chromium(VI) in real samples with good accuracy. These findings may offer a distinctive strategy for the development of methods for analyzing and monitoring chromium(VI) and expand their application in real sample monitoring.

Asunto(s)

RESUMEN

Oxometalates of vanadium(V), chromium(VI), and manganese(VII) have negative impacts on water resources due to their toxicity. To remove them, the kinetics of 0.04 mM oxometalates in natural and synthetic water were studied using graphene nanoplatelets (GNP). The GNP were dispersible in water and formed aggregates >15 µm that could be easily separated. Within 30 min, the GNP were covered with ~0.4 mg/g vanadium and ~1.0 mg/g chromium as Cr(OH)3. The reaction of 0.04 mM permanganate with 50 mg of GNP resulted in a coverage of 10 mg/g in 5 min, while the maximum value was 300 mg/g manganese as Mn2O3/MnO. TEM showed a random metal distribution on the surfaces; no clusters or nanoparticles were detected. The rate of disappearance in aerated water followed a pseudo second-order adsorption kinetics (PSO) for V(V), a pseudo second-order reaction for Cr(VI), and a pseudo first-order reaction for Mn(VII). For Cr(VI) and Mn(VII), the rate constants were found to depend on the GNP mass. Oxygen sorption occurred with PSO kinetics as a parallel slow process upon contact of GNP with air-saturated water. For thermally regenerated GNP, the rate constant decreased for V(V) but increased for Cr(VI), while no effect was observed for Mn(VII). GNP capacity was enhanced through regeneration for V(V) and Cr(VI); no effect was observed for Mn(VII). The reactions are well-suited for use in water purification processes and the reaction products, GNP, decorated with single metal atoms, are of great interest for the construction of sensors, electronic devices, and for application in single-atom catalysis (SAC).

RESUMEN

Like other heavy metals, Cr (VI) is a powerful carcinogen and mutagen agent. Its toxic effects on plants are well considered. In order to elucidate its adverse effects, the present work aims to study the mitosis aberrations of Cr (VI) on the Vicia faba root-cells and its molecular docking analysis to understand the genotoxicity mechanisms. In-vivo, Vicia faba plants were exposed to 50 and 100 µM Cr (VI) for 48 h. In-silico, molecular docking and molecular dynamics simulation were used to study the interactions between dichromate and tubulin tyrosine ligase T2R-TTL (PDBID: 5XIW) with reference to Colchicine (microtubule inhibitor). According to our results, Cr (VI) affects growth and cell division and also induces many mitosis aberrations such as chromosome sticking, anaphase/telophase bridges, lagging chromosomes and fragmentation during all phases of mitosis. On the one hand, Cr (VI) reduces mitotic index and promotes micronuclei induction. The in-silico results showed that dichromate establishes very strong bonds at the binding site of the tubulin tyrosine ligase T2R-TTL, with a binding affinity of -5.17 Kcal/Mol and an inhibition constant of 163.59 µM. These interactions are similar to those of colchicine with this protein, so dichromate could be a very potent inhibitor of this protein's activity. TTL plays a fundamental role in the tyrosination/detyrosination of tubulin, which is crucial to the regulation of the microtubule cytoskeleton. Its inhibition leads to the appearance of many morphogenic abnormalities such as mitosis aberrations. In conclusion, our data confirm the highest genotoxicity effects of Cr (VI) on Vicia faba root-cells.

Asunto(s)