RESUMEN

This work deals with the growth investigation of the methylammonium lead triiodide (MAPbI3) thin films prepared by the spin coating technique. Firstly, MAPbI3 films were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM) and UV-Visible spectroscopy as well as photoluminescence techniques are used to calculate the band gap energy. Indeed, the high-quality MAPbI3 perovskite films were obtained by using Chlorobenzene as an antisolvent with good crystallinity, large grain sizes, and higher absorption compared to MAPbI3 treated by toluene. Secondly, the performance of FTO/TiO2/MAPbI3/Spiro OMeTAD/Au perovskite solar cell was evaluated using a numerical simulation of the Solar Cell by SCAPS simulator. The effect of the structural and physical parameters of MAPbI3 absorber layer and HTL with the different antisolvents, including thickness, defect density, total charge density, donor density and electron affinity. Obtained results are: Jsc of 25.96 mA/cm2, PCE of 30.70%, Voc of 1.259 V, FF of 88.93% of MAPbI3-based solar cells when MAPbI3 is treated by toluene. However, for MAPbI3- Chlorobenzene, the I-V characteristics are rather: Jsc of 28.18 mA/cm2, PCE of 31.81%, FF of 88.19% and Voc of 1.200 V. It is pointed out that the use of chlorobenzene may be of interest to improve the perovskites solar cells performances.

Asunto(s)

RESUMEN

Fabricating perovskite films with a dominant crystal orientation is an effective path to realizing quasi-single-crystal perovskite film, which can eliminate the fluctuation of the electrical properties in films arising from grain-to-grain variations, and improve the performance of perovskite solar cells (PSCs). Perovskite (FAPbI3 ) films based on one-step antisolvent methods usually suffer from chaotic orientations due to the inevitable intermediate phase conversion from intermediates of PbI2 •DMSO, FA2 Pb3 I8 •4DMSO, and δ-FAPbI3 to α-FAPbI3 . Here, a high-quality perovskite film with (111) preferred orientation ((111)-α-FAPbI3 ) using a short-chain isomeric alcohol antisolvent, isopropanol (IPA) or isobutanol (IBA), is reported. The interaction between IPA and PbI2 leads to a corner-sharing structure instead of an edge-sharing PbI2 octahedron, sidestepping the formation of these intermediates. With the volatilization of IPA, FA+ can replace IPA in situ to form α-FAPbI3 along the (111) direction. Compared to randomly orientated perovskites, the dominantly (111) orientated perovskite ((111)-perovskite) exhibits improved carrier mobility, uniform surface potential, suppressed film defects and enhanced photostability. PSCs based on the (111)-perovskite films show 22% power conversion efficiency and excellent stability, which remains unchanged after 600 h continuous working at maximum power point, and 95% after 2000 h of storage in atmosphere environment.

Asunto(s)

RESUMEN

During the fabrication of lateral-structured photodetectors based on CH3 NH3 PbI3 film, antisolvents represented by toluene are usually used to accelerate the crystallization of perovskite. Using antisolvent not only leads to the formation of shrinkage holes at the bottom of the perovskite layer, but the toxicity of antisolvents would also hinder the industrial preparation of perovskite devices. An antisolvent-free method is a possible solution to avoid these problems. Here, we report a lateral-structured photodetector based on an antisolvent-free method. The lateral photodetector exhibited a high responsivity of 1.75 A⋅W-1 and specific detectivity (D*) of 3.54 × 1012 Jones. In particular, the results indicated that the solvent had an influence on perovskite film morphology, crystallization, and device performance. The prepared CH3 NH3 PbI3 film presented needle-like crystals and low performance with single precursor solvent N,N-dimethylformamide (DMF). In comparison, appropriate mixing of dimethyl sulfoxide (DMSO) could improve the morphology, crystallization, and performance of the film. In addition, the solvent volume ratio of the precursor had a profound effect on the performance of the as-prepared photodetectors. At a DMSO:DMF volume ratio of 5:5, the as-prepared film had massive perovskite crystals and fewer defects, resulting in optimal device performance, which can be explained by Urbach energy.

RESUMEN

Xylitol was biotechnologically produced by Kluyveromyces marxianus ATCC36907 using the hemicellulosic hydrolysate of the cashew apple bagasse (CABHH). Sequentially, the present study investigated the recovery and purification of xylitol evaluating different antisolvents [ethanol, isopropanol and the ionic liquid 2-hydroxyl-ethylammonium acetate (2-HEAA)], their proportion in the medium (10-90% v/v), and their cooling rate (VC 0.25-0.50 °C/min). These processes were contrasted with the crystallization process of commercial xylitol. This study is the first to assess xylitol crystallization using a protic ionic liquid. The hydrolysate obtained from a mild treatment with sulfuric acid contained mainly glucose and xylose at concentrations of 15.7 g/L and 11.9 g/L, respectively. With this bioprocess, a maximum xylitol production of 4.5 g/L was achieved. The performance of the investigated antisolvents was similar in all conditions evaluated in the crystallization process of the commercial xylitol, with no significant difference in yields. For the crystallization processes of the produced xylitol, the best conditions were: 50% (v/v) isopropanol as antisolvent, cooling rate of 0.5 °C/min, with a secondary nucleation of yield and purity of 69.7% and 84.8%, respectively. Under the same linear cooling rate, using ethanol, isopropanol or the protic ionic liquid 2-hydroxyl-ethylammonium acetate (2-HEAA), crystallization did not occur, probably due to the presence of carbohydrates not metabolized by the yeast in the broth, which influences the solubility curve of xylitol. With the results of this work, a possible economical and environmentally friendly process of recovery and purification of xylitol from CABHH could be proposed.

Asunto(s)

RESUMEN

Organic-inorganic hybrid perovskites have attracted considerable attention due to their superior optoelectronic properties. Traditional one-step solution-processed perovskites often suffer from defects-induced nonradiative recombination, which significantly hinders the improvement of device performance. Herein, treatment with green antisolvents for achieving high-quality perovskite films is reported. Compared to defects-filled ones, perovskite films by antisolvent treatment using methylamine bromide (MABr) in ethanol (MABr-Eth) not only enhances the resultant perovskite crystallinity with large grain size, but also passivates the surface defects. In this case, the engineering of MABr-Eth-treated perovskites suppressing defects-induced nonradiative recombination in perovskite solar cells (PSCs) is demonstrated. As a result, the fabricated inverted planar heterojunction device of ITO/PTAA/Cs0.15 FA0.85 PbI3 /PC61 BM/Phen-NADPO/Ag exhibits the best power conversion efficiency of 21.53%. Furthermore, the corresponding PSCs possess a better storage and light-soaking stability.

RESUMEN

One-step solution deposition of high-quality perovskite thin films relies heavily on a small number of antisolvents. Here, we design a simple minimum volume colorimetric solution assay to screen over 100 different solvents. We correctly identify 14 previously reported antisolvents and predict 20 novel candidates. We then refine the assay through analysis of screening results, available solvent properties, and qualitative evaluation of films cast using 50 candidates. Using the refined findings, we successfully demonstrated 15 different antisolvents for characterization and evaluation in inverted devices, including six previously unreported candidates. All candidates produced power conversion efficiencies comparable to chlorobenzene controls without any additional optimization. This work presents the largest scope of antisolvents reported, can be easily adapted to other perovskites, and opens the door to selecting antisolvents based on a wide range of desirable properties including efficiency, usability, safety, and industrial viability.

RESUMEN

The preparation of high-quality perovskite films is important for achieving high-performance perovskite solar cells (PSCs). The effective balance between solvent and antisolvent is an essential factor for regulating high-quality perovskite film during the spin-coating and thermal-annealing steps. In this work, a greener, nonhalogenated, nontoxic bifunctional (anti)solvent, methyl benzoate (MB), is developed not only as an antisolvent to rapidly generate crystal seeds at the perovskite spin-coating step, but also as a digestive-ripening solvent for the perovskite precursors, which can prevent the loss of organic components during the thermal-annealing stage and effectively suppress the formation of miscellaneous lead halide phases. As a result, this novel bifunctional (anti)solvent is employed in planar n-i-p PSCs for engineering high-quality perovskite layers and thus achieving a power conversion efficiency up to 22.37% with negligible hysteresis and >1300 h stability. Moreover, due to the high boiling point and low-volatility characteristic of MB, high-performance PSCs are achieved reproducibly at different operating temperatures (22-34 °C). Therefore, this developed bifunctional solvent system can provide a promising platform toward globally upscaling and commercializing PSCs in all seasons and regions.

RESUMEN

This study presents a novel droplet-templated antisolvent spherical crystallization method applicable to both hydrophilic and hydrophobic drugs. In both cases, an alginate hydrogel binder forms in situ, concurrently with the crystallization process, effectively binding the drug crystals into monodisperse spheres. This study presents a detailed process description with mass transfer modeling, and with characterization of the obtained alginate/drug spheres in terms of morphology, composition, and drug loading. Although glycine and carbamazepine are used as model hydrophilic and hydrophobic drugs, this method is easily generalized to other drugs, and offers several benefits such as minimal thermal impact, fast crystallization rates, high drug-binder loading ratios, and high selectivity toward metastable polymorphs.

Asunto(s)

RESUMEN

Cesium lead halide (CsPbX3, X=Cl, Br, I) perovskites are a new material system that has attracted a lot of research focus. Its tunable band gap and better thermal stability than organic lead halide perovskite give it the potential for applications in optoelectronic devices such as light-emitting diodes and solar cells. Here we have synthesized CsPbBr3-xIx perovskite quantum dots (QDs) via a solution process, and then have selected three different anti-solvents to purify the product. A significant effect on optical properties of CsPbBr3-xIx was found after the centrifugation process. Up to a ∼40nm shift was observed in mixed halide CsPbBr3-xIx QDs in both absorbance and PL spectra after purification while there was no obvious change in pure CsPbBr3 when it was subjected to the same purification steps. XPS analysis shows that the Br:I ratio of the CsPbBr3-xIx QDs had changed as a result of exposure to the anti-solvent, causing the change of the band gap and shift of the spectra. It is also shown that iodine can be removed more easily than bromine during the anti-solvent purification. Ab-initio simulations of small CsPbBr3-xIx atomic clusters suggest that exposed Cs ions on Cs-terminated facets are the first species to be attacked by hydrophilic molecules, likely dragging halide ions into solution with them to maintain overall charge neutrality in the material. Charge carrier recombination rates were found to be unchanged and all samples maintained a good PL quantum yield which was more than 44%.

RESUMEN

A simple process for batch or continuous formation of polymer nanofibers and other nanomaterials in the bulk of a sheared fluid medium is introduced. The process may be of high value to commercial nanotechnology, as it can be easily scaled up to the fabrication of staple nanofibers at rates that may exceed tens of kilograms per hour.

Asunto(s)

RESUMEN

An anti-solvent for graphene oxide (GO), hexane, is introduced to increase the surface area and the pore volume of the non-stacked GO/reduced GO 3D structure and allows the formation of a highly crumpled non-stacked GO powder, which clearly shows ideal supercapacitor behavior.