RESUMEN

Embedded 3D printing (EMB3D) is an additive manufacturing technique that enables complex fabrication of soft materials including tissues and silicones. In EMB3D, a nozzle writes continuous filaments into a support bath consisting of a yield stress fluid. Lack of fusion defects between filaments can occur because the nozzle pushes support fluid into existing filaments, preventing coalescence. Interfacial tension was previously proposed as a tool to drive interfilament fusion. However, interfacial tension can also drive rupture and shrinkage of printed filaments. Here, we evaluate the efficacy of interfacial tension as a tool to control defects in EMB3D. Using polydimethylsiloxane (PDMS)-based inks with varying amounts of fumed silica and surfactant, printed into Laponite in water supports, we evaluate the effect of rheology, interfacial tension, print speeds, and interfilament spacings on defects. We print pairs of parallel filaments at varying orientations in the bath and use digital image analysis to quantify shrinkage, rupture, fusion, and positioning defects. By comparing disturbed filaments to printed pairs of filaments, we disentangle the effects of nozzle movement and filament extrusion. Critically, we find that capillary instabilities and interfilament fusion scale with the balance between support rheology and interfacial tension. Less viscous supports and higher interfacial tensions lead to more shrinkage and rupture at all points in the printing process, from relaxation after writing, to disturbance of the line, to writing of a second line. It is necessary to overextrude material to achieve interfilament fusion, particularly at high support viscosities and low interfacial tensions. Finally, fusion quality varies with printing orientation, and writing neighboring filaments causes displacement of existing structures. As such, specialized slicers are needed for EMB3D that consider the tighter spacings and orientation-dependent spacings necessary to achieve precise control over printed shapes.

RESUMEN

Abstract: A numerical study of yield-stress fluids flowing in porous media is presented. The porous media is randomly constructed by non-overlapping mono-dispersed circular obstacles. Two class of rheological models are investigated: elastoviscoplastic fluids (i.e. Saramito model) and viscoplastic fluids (i.e. Bingham model). A wide range of practical Weissenberg and Bingham numbers is studied at three different levels of porosities of the media. The emphasis is on revealing some physical transport mechanisms of yield-stress fluids in porous media when the elastic behaviour of this kind of fluids is incorporated. Thus, computations of elastoviscoplastic fluids are performed and are compared with the viscoplastic fluid flow properties. At a constant Weissenberg number, the pressure drop increases both with the Bingham number and the solid volume fraction of obstacles. However, the effect of elasticity is less trivial. At low Bingham numbers, the pressure drop of an elastoviscoplastic fluid increases compared to a viscoplastic fluid, while at high Bingham numbers we observe drag reduction by elasticity. At the yield limit (i.e. infinitely large Bingham numbers), elasticity of the fluid systematically promotes yielding: elastic stresses help the fluid to overcome the yield stress resistance at smaller pressure gradients. We observe that elastic effects increase with both Weissenberg and Bingham numbers. In both cases, elastic effects finally make the elastoviscoplastic flow unsteady, which consequently can result in chaos and turbulence.

RESUMEN

Necking and barreling deformation behaviors occurred simultaneously during the bending test of a single-crystal gold micro-cantilever (sample A) with the loading direction parallel to the [1-10] orientation and the neutral plane parallel to the [110] orientation. In contrast, for another single-crystal gold micro-cantilever, sample B, with the loading direction aligned parallel to the [0.37 -0.92 0.05] orientation and the neutral plane parallel to the [0.54 0.28 0.78] orientation, predominant slip band deformation was noted. Sample A exhibited activation of four slip systems, whereas sample B demonstrated activity in only a single-slip system. This difference suggests that the presence of multiple slip systems contributes to the concurrent occurrence of necking and barreling deformations. Furthermore, variations in the thickness of the micro-cantilevers resulted in observable strengthening, indicating that the effect of sample size is intricately linked to the geometry of the cross-section, which we have termed the "sample geometry effect".

RESUMEN

In this work, the effect of sonication on the molecular characteristics of polyacrylic acid (Carbopol® Ultrez 10), as well as on its rheological behavior in aqueous dispersions and microgels, was analyzed for the first time by rheometry, weight-average molecular weight (Mw) measurements via static light scattering (SLS), Fourier transform infrared (FTIR) spectroscopy and confocal microscopy. For this, the precursor dispersion and the microgels containing 0.25 wt.% of Ultrez 10 were sonicated in a commercial ultrasound bath at constant power and at different times. The main rheological properties of the microgel, namely, shear modulus, yield stress and viscosity, all decreased with increasing sonication time, while the microgel's Herschel-Bulkley (H-B) behavior, without thixotropy, was preserved. Also, Mw of Ultrez 10 decreased up to almost one-third (109,212 g/mol) of its original value (300,860 g/mol) after 180 min of sonication. These results evidence a softening of the gel microstructure, which results from the reduction in the Mw of polyacrylic acid with sonication time. Separately, FTIR measurements show that sonication produces scission in the C-C links of the Carbopol® backbone, which results in chains with the same chemistry but lower molecular weight. Finally, confocal microscopy observations revealed a diminution of the size of the microsponge domains and more free solvent with sonication time, which is reflected in a less compact and softer microstructure. The present results indicate that both the microstructure and the rheological behavior of Carbopol® microgels, in particular, and complex fluids, in general, may be manipulated or tailored by systematic high-power ultrasonication.

RESUMEN

This study aims to understand the water retention capabilities of Superabsorbent Polymers (SAPs) in different alkaline environments for internal curing and to assess their impact on the rheological properties of cement paste. Therefore, the focus of this paper is on the absorption capacities of two different sizes of polyacrylic-based Superabsorbent Polymers : SAP A, with an average size of 28 µm, and SAP B, with an average size of 80 µm, in various solutions, such as pH 7, pH 11, pH 13, and cement filtrate solution (pH 13.73). Additionally, the study investigates the rheological properties of SAP-modified cement pastes, considering three different water-to-cement (w/c) ratios (0.4, 0.5, and 0.6) and four different dosages of SAPs (0.2%, 0.3%, 0.4%, and 0.5% by weight of cement). The results showed that the absorption capacity of SAP A was higher in all solutions compared to SAP B. However, both SAPs exhibited lower absorption capacity and early desorption in the cement filtrate solution. In contrast to the absorption results in pH 13 and cement filtrate solutions, the rheological properties, including plastic viscosity and yield stress, of the cement paste with a w/c ratio of 0.4 and 0.5, as well as both dry and wet (presoaked) SAPs, were higher than those of the cement paste without SAP, indicating continuous absorption by SAP. The viscosity and yield stress increased over time with increasing SAP dosage. However, in the mixes with a w/c ratio of 0.6, the values of plastic viscosity and yield stress were initially lower for the mixes with dry SAPs compared to the reference mix. Additionally, cement pastes containing wet SAP showed higher viscosity and yield stress compared to the pastes containing dry SAP.

RESUMEN

In this study, we delve into the intricacies of elastoviscoplastic (EVP) fluids, particularly focusing on how polymer additives influence their extensional behavior. Our findings reveal that polymer additives significantly alter the extensional properties of the EVP fluids, such as relaxation time and extensional stresses while having negligible impact on the shear rheology. Interestingly, the modified fluids exhibit a transition from yield stress-like behavior to viscoelastic-like behavior under high extensional rates, ultimately leading to destabilization under extreme deformation. This research enhances the fundamental understanding of EVP fluids and highlights potential advancements in applications, especially in precision-demanding fields like 3D printing.

RESUMEN

The jaws and their supporting cartilages are tessellated in elasmobranchs and exhibit an abrupt increase in stiffness under compression. The major jaw-supporting cartilage, the hyomandibula, varies widely by shape and size and the extent of the load-bearing role is hypothesized to be inversely related to the number of craniopalatine articulations. Here, we test this hypothesis by evaluating the strength of the hyomandibular cartilage under compression in 13 species that represent all four jaw suspension systems in elasmobranchs (amphistyly, orbitostyly, hyostyly, and euhyostyly). The strength of the hyomandibular cartilages was measured directly using a material testing machine under compressive load, and indirectly by measuring morphological variables putatively associated with strength. The first measure of strength is force to yield (Fy), which was the peak force (N) exerted on the hyomandibula before plastic deformation. The second measure was compressive yield strength (σy, also called yield stress), which is calculated as peak force (N) before plastic deformation/cross-sectional area (mm2) of the specimen. Our results show that the load-bearing role of the hyomandibular cartilage, as measured by yield strength, is inversely related to the number of craniopalatine articulations, as predicted. Force to yield was lower for euhyostylic jaw suspensions and similar for the others. We also found that mineralization is associated with greater yield strength, while the second moment of area is associated with greater force to yield.

Asunto(s)

RESUMEN

Lime is widely used for soft ground treatment, rendering the compressibility of lime-treated soil a crucial factor in deformation analysis in engineering applications. This study investigated the compressibility of three remoulded lime-treated slurries with high water content in Southeast China. Sixty groups of oedometer tests were conducted on lime-treated soils with an initial water content of 1 to 3 times the liquid limit and lime contents between 1 and 3%. The oedometer test results were discussed to examine the remoulded yield stress σ y ' of lime-treated slurry. Considering the relationships between σ y ' , the void ratio, lime content, and initial water content were preliminarily discussed and quantitatively established. Research on the normalised compression curve of lime-treated soil revealed that for soil samples containing a lime content of 0-%, the normalised compression curve at σ p ' > σ y ' can be represented by a unique line. Furthermore, the log(1 + e) - log σ v ' compression curve of lime-treated slurry at pre-yield state is analysed, and a prediction method for the modified compression index is proposed.

RESUMEN

This research investigates the modeling of the pharmaceutical roller compaction process, focusing on the application of the Johanson model and the impact of varying roll speeds from 1 to 15 RPM on predictive accuracy of ribbon solid fraction. The classical Johanson's model was integrated with a dwell time parameter leading to an expression of a floating correction factor as a function of roll speed. Through systematic analysis of the effect of different roll speeds on the solid fraction of ribbons composed of microcrystalline cellulose, lactose, and their blends, corrective adjustment to the Johanson model was found to depend on both roll speed and formulation composition. Interestingly, the correction factor demonstrated excellent correlation with the blend's mechanical properties, namely yield stress (Py) and elastic modulus (E0), representative of the deformability of the powder. Validated by a multicomponent drug formulation with ±0.4-1.3 % differences, the findings underscore the utility of this modified mechanistic approach for precise prediction of ribbon solid fraction when Py or E0 is known for a given blend. Hence, this work advances the field by offering early insights for more accurate and controllable roller compaction operations during late-stage pharmaceutical manufacturing.

Asunto(s)

RESUMEN

Compliant materials are crucial for stretchable electronics. Stretchable solids and gels have limitations in deformability and durability, whereas active liquids struggle to create complex devices. This study presents multifunctional yield-stress fluids as printable ink materials to construct stretchable electronic devices. Ionic nanocomposites comprise silica nanoparticles and ion liquids, while electrical nanocomposites use the natural oxidation of liquid metals to produce gallium oxide nanoflake additives. These nanocomposite inks can be printed on an elastomer substrate and stay in a solid state for easy encapsulation. However, their transition into a liquid state during stretching allows ultrahigh deformability up to the fracture strain of the elastomer. The ionic inks produce strain sensors with high stretchability and temperature sensors with high sensitivity of 7% °C-1. Smart gloves are further created by integrating these sensors with printed electrical interconnects, demonstrating bimodal detection of temperatures and hand gestures. The nanocomposite yield-stress fluids combine the desirable qualities of solids and liquids for stretchable devices and systems.

RESUMEN

The literature suggests that the yield strain of cortical bone is invariant to its stiffness (elastic modulus) and strength (yield stress). However, data about intra-individual variations, e.g., the influence of different collagen/mineral organisations observed in bone aspects withstanding different habitual loads, are lacking. The hypothesis that the yield strain of human cortical bone tissue, retrieved from femoral diaphyseal quadrants subjected to different habitual loads, is invariant was tested. Four flat dumbbell-shaped specimens were machined from each quadrant of the proximal femoral diaphysis of five adult donors for a total of 80 specimens. Two extensometers attached to the narrow specimen region were used to measure deformation during monotonic tensile testing. The elastic modulus (linear part of the stress-strain curve) and yield strain/stress at a 0.2% offset were obtained. Elastic modulus and yield stress values were, respectively, in the range of 12.2-20.5 GPa and 75.9-136.6 MPa and exhibited a positive linear correlation. All yield strain values were in the narrow range of 0.77-0.87%, regardless of the stiffness and strength of the tissue and the anatomical quadrant. In summary, the results corroborate the hypothesis that tensile yield strain in cortical bone is invariant, irrespective also of the anatomical quadrant. The mean yield strain value found in this study is similar to what was reported by inter-species and evolution studies but slightly higher than previous reports in humans, possibly because of the younger age of our subjects. Further investigations are needed to elucidate a possible dependence of yield strain on age.

RESUMEN

In this study, composite particles of rGO/CoFe2O4 were synthesized using a solvothermal method to fabricate a low-density magnetorheological (MR) material with enhanced sedimentation stability. The morphology and crystallographic features of rGO/CoFe2O4 were characterized via SEM, TEM, and XRD, and its magnetic properties were tested using VSM. The MR fluid was formulated by blending rGO/CoFe2O4 particles into silicone oil. Under different magnet strengths (H), a rotational rheometer was used to test its MR properties. Typical MR properties were observed, including shear stress, viscosity, storage/loss modulus, and dynamic yield stress (τdy) following the Herschel-Bulkley model reaching 200 Pa when H is 342 kA/m. Furthermore, the yield stress of the MR fluid follows a power law relation as H increases and the index changes from 2.0 (in the low H region) to 1.5 (in the high H region). Finally, its MR efficiency was calculated to be about 104% at H of 342 kA/m.

RESUMEN

Planarly aligning 2D platelets is challenging due to their additional orientational freedom compared to 1D materials. This study reports a sequential dual-alignment approach, employing an extrusion-printing-induced shear force and rotating-magnetic-field-induced force couple for platelet planarly alignment in a yield-stress support bath. It is hypothesized that the partial alignment induced by a directional shear force facilitates subsequent axial rotation of the platelets for planar alignment under an external force couple, resulting in a synergistic alignment effect. This sequential dual-alignment approach achieves better planar alignment of 2D modified hexagonal boron nitride (mhBN). Specifically, the thermal conductivity of the 40 wt% mhBN/epoxy composite is significantly higher (692%) than that of unaligned composites, surpassing the cumulative effect of individual methods (only 133%) with a 5 times more synergistic effect. For 30, 40, and 50 wt% mhBN composites, the thermal conductivity values (5.9, 9.5, and 13.8 W m-1 K-1) show considerable improvement compared to the previously reported highest values (5.3, 6.6, and 8.6 W m-1 K-1). Additionally, a 3D mhBN/epoxy heat sink is printed and evaluated to demonstrate the feasibility of device fabrication. The approach enables the planar alignment of electrically or thermally conducting 2D fillers during 3D fabrication.

RESUMEN

This study aims to investigate the effects of introducing a 50/50 mixture of silica and magnesium oxide nanoparticles (SNP + MgONP) to the viscosity of Al-Ahdab crude oil (Iraq) at varied concentrations and temperatures. It is observed that the viscosity value drops from 38.49 to 7.8 cP. The highest degree of viscosity reduction is measured to be 56.91% at the maximum temperature of 50 °C and the greatest concentration of 0.4 wt% SM4. The Bingham model can be used to classify the behavior of the crude oil before the Nano-mixture is added. The liquid behavior grew closer to Newtonian behavior once the Nano-mixture was added. Along with a rise in plastic and effective viscosity values, the yield stress value decreases as the concentration of the Nano-mixture increases. The numerical data demonstrate that when the volume proportion of nanoparticles increases, the pressure distribution decreases. Furthermore, as the nanoparticle volume fraction increases, the drag decrease would also increase. SM4 obtains a maximum drag reduction of 53.17%. It is discovered that the sample SM4 has a maximum flow rate increase of 2.408%. Because they reduce the viscosity of crude oil, nanoparticles also reduce the friction factor ratio.

RESUMEN

Swallowing oral solid dosage forms is challenging for those who have medication swallowing difficulties, including patients with dysphagia. One option is to mix the drug (whole or crushed) with a thick vehicle (medication lubricant). Previous in vitro studies consistently suggest that thick vehicles could impact the dissolution of solid dosage forms, potentially influencing their therapeutic effectiveness, but do not account for changes that happen during oral processing and swallowing. This study aims to investigate the potential impact of medication lubricants on drug release and examine the effect of oral processing. In vitro dissolution of whole and crushed paracetamol tablets mixed with five commercially available medication lubricants (two IDDSI level 2, two IDDSI level 3, and one IDDSI level 4) were tested with and without oral processing; a medication lubricant with/without paracetamol was placed in the mouth (five healthy volunteers), prepared for swallowing, but then expectorated and assessed for physical characteristics and drug release. Medication lubricants, both alone and mixed with crushed paracetamol tablets, showed a significant decrease in viscosity after oral processing. Without oral processing, IDDSI level 3 and 4 lubricants significantly delayed the dissolution of paracetamol tablets. After oral processing, particularly with crushed tablets, there was a substantial increase in the dissolution rate. These findings suggest that dissolution testing overestimates the impact of medication lubricants on drug dissolution. Therefore, using in vitro dissolution tests to predict the dissolution rate of medications mixed with thick vehicles is discouraged. It is essential to consider ways to incorporate the effects of the oral environment and oral processing on thick vehicles used for oral medication administration.

RESUMEN

Creating tissue and organ equivalents with intricate architectures and multiscale functional feature sizes is the first step toward the reconstruction of transplantable human tissues and organs. Existing embedded ink writing approaches are limited by achievable feature sizes ranging from hundreds of microns to tens of millimeters, which hinders their ability to accurately duplicate structures found in various human tissues and organs. In this study, a multiscale embedded printing (MSEP) strategy is developed, in which a stimuli-responsive yield-stress fluid is applied to facilitate the printing process. A dynamic layer height control method is developed to print the cornea with a smooth surface on the order of microns, which can effectively overcome the layered morphology in conventional extrusion-based three-dimensional bioprinting methods. Since the support bath is sensitive to temperature change, it can be easily removed after printing by tuning the ambient temperature, which facilitates the fabrication of human eyeballs with optic nerves and aortic heart valves with overhanging leaflets on the order of a few millimeters. The thermosensitivity of the support bath also enables the reconstruction of the full-scale human heart on the order of tens of centimeters by on-demand adding support bath materials during printing. The proposed MSEP demonstrates broader printable functional feature sizes ranging from microns to centimeters, providing a viable and reliable technical solution for tissue and organ printing in the future.

Asunto(s)

RESUMEN

Accurate prediction and measurement of yield stress are crucial for optimizing sludge treatment and disposal. However, the differences and applicability of various methods for measuring yield stress are subjects of ongoing debate. Meanwhile, literature on measuring sludge yield stress is limited to low solid concentrations (TS <10%), understanding and studying the yield stress of medium to high solid concentration sludge is crucial due to increasingly stringent standards for sludge treatment and disposal. So, this study employed a rotational rheometer to measure sludge yield stress across a wide range of TS (4-50%) using steady shear, dynamic oscillatory shear, and transient shear. The study derived significant conclusions by comparing and summarizing the applicability and limitations of each testing method: Dynamic oscillatory shear methods, including G'-σ curve method, γ-σ curve method, and G**γc method can measure sludge yield stress ranging from 4% to 40% TS, while other methods are restricted to low or limited solid concentrations; The G' = G″ method, utilizing the intersection of G' and G″ curves, consistently yields the highest value for yield stress when 4%≤ TS ≤ 12%; The rotational rheometer cannot measure sludge yield stress when the solid concentration exceeds 40% TS; The relationship between sludge yield stress and solid concentration is stronger as a power-law for TS ≤ 25%, transitioning to linear for higher concentrations (28%≤ TS <40%). This study systematically explores the applicability and limitations of various measurement methods for characterizing sludge yield stress across a wide range of solid concentrations, providing valuable guidance for scientific measurement and highlighting challenging research issues.

Asunto(s)

RESUMEN

Consumer concern about intake of added sugars has increased commercial demand for sugar-reduced chocolates. However, substitution with high-potency sweeteners is not possible as sugar serves as an important bulking agent. Here, we investigated replacement of sucrose in chocolate compound with oat or rice flours, with starch granules smaller than 10 µm, focusing on texture, sweetness, and acceptability. In Study 1, six chocolates were made: a control with 54% sucrose, four sucrose-reduced versions (reductions of 25% or 50%, using either oat or sweet rice flour), and one 54% sucrose chocolate with reduced refining time. These chocolates were compared in a Difference from Control (DFC) test in a within-subject design, with and without nose clips. Particle size distribution, yield stress, and plastic viscosity were measured. Chocolates with 25% sucrose reduction by either sweet rice or oat flour (or reduced refining time) were not significantly different from the blind control (p > 0.05), regardless of nose clip use. In open-ended comments, participants reported differences in rice-flour-containing chocolates were due to a chalkier texture, while oat-flour-containing chocolates were described as smoother, softer, and creamier. DFC scores from the chocolates were positively correlated with plastic viscosity and negatively correlated with yield stress. In Study 2, 25% reduced sugar chocolates made with rice flour were liked significantly less than control, but the oat flour sample did not differ from control. Collectively, these results suggest up to 25% of sucrose in chocolate can be replaced with oat flour without negatively affecting texture or consumer acceptance.

Asunto(s)

RESUMEN

This study aimed to investigate the influence of incorporating Lepidium perfoliatum seed gum (LPSG) into wheat starch (WS) at various mixing ratios on its FTIR, DSC, steady and dynamic rheological properties, pasting attributes, syneresis, and particle size distributions characteristics. The interaction between WS and LPSG was purely based on hydrogen-bonding. It was found that the onset (To) and peak (Tp) temperatures of the LPSG-rich mixtures increased by 10 % and 8 %, respectively, while the enthalpy (ΔH) decreased by 70 % compared to WS. A higher LPSG ratio led to a decrease in the frequency dependence of storage modulus (G'), as well as an increase in the pseudoplasticity of the mixtures. The in-shear structural recovery test showed that the rate of recovery (R, %) increased with an increasing LPSG ratio. The pasting results demonstrated that the 9/1 ratio had the highest final viscosity and the lowest relative breakdown. Applying 1 to 5 freeze-thaw cycles resulted in a 50 % to 70 % decrease in syneresis for the 9/1 mixing ratio in comparison to WS, respectively. The incorporation of LPSG into WS resulted in higher static and dynamic magnitudes of yield stress, as well as an increase in particle size when compared to WS.

Asunto(s)

RESUMEN

RANS simulation of turbulent non-isothermal flow in a pipe by transition of Newtonian fluid into a viscoplastic non-Newtonian fluid is carried out. Carrier phase turbulence was modeled using two-equation isotropic k‒ε˜ - model and Reynolds stress transport model. Results of calculations of Newtonian and non-Newtonian power-law fluids were compared with data of DNS calculations of other authors. Comparisons with data from other works for isothermal Schwedoff-Bingham fluid were performed in this work using k‒ε˜ - model. Satisfactory agreement was obtained with data from other studies for the axial averaged velocity and turbulent kinetic energy radial profiles (the difference is up to 15 %). Reynolds stress transport model showed significant anisotropy between streamwise and transverse velocity fluctuations (up to several times) and good agreement with DNS results of other authors. Averaged and pulsation profiles express the indicated transformation of the non-isothermal turbulent flow.