RESUMEN

Objective: This laboratory study evaluated the effect of Salvadora persica (S. persica) root extracts and Chlorhexidine Digluconate (CHX) on the antibacterial and surface hardness properties of glass ionomer cement (GIC). Methods: The in vitro experimental study was conducted at the Baqai Institute of Pharmaceutical Sciences of Baqai Medical University, Karachi, Pakistan, from October 2022 to March 2023. There were a total four experimental groups. The first group consisted of ethanol extract (GIC-SPEE) and second group consisted of hexane extract as (GIC-SPHE) both prepared from Salvadora persica root respectively, and mixed with liquid of GIC separately. The third group comprised chlorhexidine (GIC-CHX) that was also mixing into liquid portion of GIC and the last group was Control i.e. (cGIC). The GIC samples were prepared by using stainless steel metallic moulds with dimension (5mm x 2mm), following the manufacturer guidelines. Antibacterial activity against Streptococcus mutans was done by disc diffusion test (DDT), and surface hardness test was done by Vickers hardness tester. Statistical analysis was performed using One-Way ANOVA and Tukey's post hoc tests (p<0.05). Results: The antibacterial activity against S. mutans reported that the maximum zone of inhibition was obtained at 3 wt% by the GIC-SPEE, when compared with other experimental groups. For surface hardness, the highest mean and standard deviation and significant findings was reported by the group GIC-SPEE. Conclusions: Considering the outcome of this in vitro study, it can be concluded that the addition of 3 wt% GIC-SPEE increased the surface hardness and antibacterial activity against Streptococcus mutans.

RESUMEN

Experimental light-curing pattern resins were fabricated to produce pattern resin materials with adequate dimensional stability. The light-curing pattern resins consisted of poly(n-butyl methacrylate) or poly(iso-butyl methacrylate) (PiBMA) polymers and methacrylate monomers. The physical properties, amount of residual ash after burning, Vickers hardness, flexural strength, and volumetric polymerization shrinkage of each material were determined. The data obtained for the prepared resins were compared with those of a commercially available pattern resin, Palavit G (PG). A lower amount of residual ash was observed for some of the prepared resins than for PG. The Vickers hardness and flexural strength values of all experimental resins were lower than those of PG. The volumetric polymerization shrinkage of all the experimental resins based on PiBMA was lower than that of PG. These results suggest that acrylic light-curing resin materials based on PiBMA may be useful for patterning and indexing during soldering.

Asunto(s)

RESUMEN

Purpose This study evaluated the color alterations, flexural strength and microhardness properties of two different 3D-printed permanent crown resins. Materials and Methods Samples were produced from two different 3D Print permanent crown resins: Group 1 (Saremco Crowntec; Saremco, Switzerland), Group 2 (P-crown Version 2; Senertek, Turkey). Color changes (ΔE values), flexural strenght and vickers hardness number of the samples were calculated. Data were analyzed with Shapiro-Wilk normality test, Independent-t test, and Mann Whitney-U tests. Significance level was accepted as P<0.05. Results ΔE values for red wine were found to be significantly higher in Group 1 (6.43Å}2.26; P<0.001). The flexural strength values (MPa) of Group 1 were significantly higher than Group 2 in all three solutions (P<0.001). There was no significant difference between the VHN values of the samples kept in wine and coffee solutions (P= 0.271; 0.827). Conclusion 3D printing resins are affected at different levels by coloring solutions. Microhardness and flexural strength of 3D print samples kept in different coloring agents are different.In the use of 3D printing resins, product selection should be made by taking into account the individual factors such as the eating and drinking habits of the patients and the physical properties expected from the sample.

RESUMEN

Hardness is one of the most crucial mechanical properties, serving as a key indicator of a material's suitability for specific applications and its resistance to fracturing or deformation under operational conditions. Machine learning techniques have emerged as valuable tools for swiftly and accurately predicting material behavior. In this study, regression methods including decision trees, adaptive boosting, extreme gradient boosting, and random forest were employed to forecast Vickers hardness values based solely on scanned monochromatic images of indentation imprints, eliminating the need for diagonal measurements. The dataset comprised 54 images of D2 steel in various states, including commercial, quenched, tempered, and coated with Titanium Niobium Nitride (TiNbN). Due to the limited number of images, non-deep machine learning techniques were utilized. The Random Forest technique exhibited superior performance, achieving a Root Mean Square Error (RMSE) of 0.95, Mean Absolute Error (MAE) of 0.12, and Coefficient of Determination (R2) ≈ 1, surpassing the other methods considered in this study. These results suggest that employing machine learning algorithms for predicting Vickers hardness from scanned images offers a promising avenue for rapid and accurate material assessment, potentially streamlining quality control processes in industrial settings.

RESUMEN

Interproximal enamel reduction, also known as stripping, is a common orthodontic procedure that reduces the mesiodistal diameter of teeth, allowing for a balance of available space in dental arches. The aim of this study was to assess the enamel surface microhardness resulting from the application of currently available methods for interproximal reduction. Forty-two extracted human permanent teeth were divided into six different groups, each subjected to a therapeutic stripping procedure using various methods (i.e., diamond burs, abrasive strips of 90 µm, 60 µm, 40 µm, and 15 µm, and abrasive discs). Stripping was performed by a single individual in accordance with the manufacturers' recommendations for the various systems used. One of the proximal faces of the tooth underwent IPR, while the other side remained untreated for control. The hardness of the enamel surface was measured using a Vickers hardness tester. The control group achieved the hardest enamel surface (354.4 ± 41.02 HV1), while the lowest was observed for enamel surfaces treated with 90 µm abrasive strips (213.7 ± 118.6). The only statistically significant difference was identified in comparisons between the values measured for the control group and those obtained after stripping with diamond burs (p = 0.0159). Enamel microhardness varied depending on the stripping instrument used, but no statistically significant differences were found (p > 0.05). Optimal microhardness values, close to those of healthy enamel, were achieved after mechanical treatment with 15 µm abrasive strips and abrasive discs. Dental stripping is a safe therapeutic procedure that has a relatively minor influence on the microhardness of surface enamel.

RESUMEN

This study evaluated the effect of different post-curing cycles on the Vickers hardness, color change, and translucency value of 3D printed methacrylic acid ester-based temporary and permanent crown resins. A total of 300 samples were printed in disk shape (ø:8 mm, thickness: 2 mm) using VarseoSmile Crown Plus (VSC) and VarseoSmile Temp (VST) materials from a 3D printer. These disks were divided into five subgroups (n = 30 each) based on flash-curing cycles (0, 750, 1500, 2250, and 3000). Surface hardness tests and color tests were conducted on both the green state and flash-cured groups. The data were analyzed using univariate analysis of variance (ANOVA). The hardness of 3D printed temporary and permanent crown resin increased with post-curing time. Compared to the post-curing cycle recommended by the manufacturer, no clinically significant color change (ΔE00 ≥ 2.25) was observed in any of the polymerized groups. It was determined that permanent crown material had a more translucent structure than temporary crown material. The interaction between material and post-curing had significant effects on surface hardness, color (ΔE00), and translucency of 3D printed methacrylic acid ester-based resins.

RESUMEN

The organic single crystals of Cyclohexylammonium picrate (CHAP) had been grown using the method of slow evaporation solution growth. A determination was made regarding the solubility of the substance. The crystal's lattice cell parameters and morphology were characterized using single-crystal X-ray diffraction and powder X-ray diffraction techniques. The HRXRD techniques were utilized to assess the crystal quality. The functional groups of CHAP material were identified through the use of FT-IR and FT-Raman analysis. A Hirshfeld surface analysis was performed to investigate the formation of hydrogen bonds between N-H⋯O and C-H⋯O molecules. The grown crystals were examined in optical and thermal investigations utilizing UV-visible and TGA, DSC techniques. Mechanical analysis is used to quantify surface properties, such as work hardening coefficient and void volume. Z-scan analysis was utilized to calculate the non-linear refractive index (n2), nonlinear absorption (ß), and third-order non-linear susceptibility (χ3).

RESUMEN

OBJECTIVE: The aim of this in vitro study was to evaluate the effect of radiotherapy on the surface microhardness and roughness of different bioactive restorative materials. MATERIALS AND METHODS: A total of 60-disc specimens (5 mm × 2 mm) were performed in four groups (n = 15 each) from Equia Forte HT, Cention N, Activa Bioactive Restorative, and Beautifil II. Following the polishing procedure (600, 1000, 1200 grit silicon carbide papers), all specimens were irradiated at 2 Gy per fraction, five times a week for a total dose of 70 Gy in 30 fractions over 7 weeks. Before and after the irradiation, the specimens were analyzed regarding the surface roughness and microhardness. Surface morphology was also analyzed by scanning electron microscopy. Kruskal-Wallis test, Wilcoxon test, and paired sample t-test were used for statistical analysis. RESULTS: Significant differences were found after radiation with increased mean roughness of both Cention N (p = 0.001) and Beautifil II (p < 0.001) groups. In terms of microhardness, only the Beautifil II group showed significant differences with decreased values after radiation. There were statistically significant differences among the groups' roughness and microhardness data before and after radiotherapy (p < 0.05). CONCLUSION: The effect of radiotherapy might differ according to the type of the restorative material. Although results may differ for other tested materials, giomer tends to exhibit worse behaviour in terms of both surface roughness and microhardness. CLINICAL RELEVANCE: In patients undergoing head and neck radiotherapy, it should be taken into consideration that the treatment process may also have negative effects on the surface properties of anti-caries restorative materials.

Asunto(s)

RESUMEN

Dental amalgams have been used by dentists for the restoration of posterior human teeth. However, there have been concerns about the release of mercury from amalgams into the oral cavity. The objective of the present research is to study the effect of titanium (Ti) nanoparticles on the microstructural mechanism of the release of mercury vapor in two commonly used brands of dental amalgam (the Dispersalloy: 11.8% Cu; the Sybralloy: 33% Cu). Ti powder was added to both the Dispersalloy and the Sybralloy in increments of 10 mg up to 80 mg. The addition of Ti powder to both brands of dental amalgam has been found to result in a considerable decrease in Hg vapor release. The decrease in the Hg vapor release due to Ti addition has been explained by the formation of strong Hg-Ti covalent bonds, which reduce the availability of Hg atoms for evaporation. The Ti atoms in excess of the solubility limit of Ti in Hg reside in the grain boundaries, which also reduces the evaporation of Hg from the amalgam. The binding of Hg with Ti via a strong covalent bond also results in a significant improvement in mechanical properties such as Vickers hardness.

RESUMEN

The main aim of this study was to assess the impact of the environment on the mechanical and tribological properties of glass-carbomer cements used in dentistry. The properties of the Glass Cements Polyalkene (GCP) Glass Fill material, belonging to glass-polyalkene cements, were tested after placing it in various environments: air, distilled water, artificial saliva simulating a neutral environment (pH = 7), and simulating inflammation (pH = 4). The research material included four samples and a two-year reference material. The analysis of volumetric consumption and the assessment of the impact of solubility on the stability of glass-carbomer cements were carried out using tribological measurements and Vickers hardness measurements. In addition, microstructural characterization of the materials was performed using scanning electron microscopy (SEM). It was observed that the lowest wear (0.04%), the most stable microstructure, and the lowest average hardness (21.52 HV 0.1) were exhibited by the material stored in artificial saliva simulating a neutral environment (pH = 7). The least stable microstructure and statistically the highest hardness (77.3 HV 0.1) was observed in the test sample, which was stored in air for two years and then in distilled water. The highest consumption (0.11%) was recorded in the case of cement placed in artificial saliva simulating inflammation (pH = 4). The results obtained in this study indicate specific trends in the influence of the environment in which the tested cement is located, such as air, distilled water, air/distilled water, artificial saliva simulating a neutral environment, and simulating inflammation, on its structure, hardness, and wear.

RESUMEN

BACKGROUND: Glass fibre-reinforced composite (GFRC) has the potential to enhance the mechanical properties of resin-based restorations. Nevertheless, the application technique can influence the cervical margin porosity, potentially reducing the mechanical strength of restorations. METHODS: In an in vitro setup, mould specimens underwent six different treatments to assess the effects of snowplow and incremental curing techniques on the properties of GFRC (EverX) and universal resin composite (Filtek). Mechanical properties, namely flexural strength (FS), compressive strength (CS) and Vickers hardness (VH), were evaluated following ISO 4049 standards. Data interpretation utilized the Kruskal-Wallis tests. RESULTS: No significant difference emerged across groups for FS. CS in the snowplow method with lesser EverX thickness (SnPl_1) was comparable with only EverX and Filtek (P > 0.05). The CS was reduced in the snowplow technique with greater EverX thickness (SnPl_2) (P < 0.05) and further decreased with the incremental method (P < 0.001). VH results showed that EverX Posterior was consistently softer than Filtek, with specific patterns of hardness variations among different application methods. CONCLUSIONS: Applying EverX and Filtek using the snowplow technique delivers superior CS and VH for restorations in contrast to the incremental method. Utilizing the snowplow approach in high-stress areas can make restorations more fracture-resistant.

Asunto(s)

RESUMEN

This paper reports the microstructural characteristics and mechanical properties of yttria-stabilized zirconia prepared via fused deposition modelling and slip casting. X-Ray Diffraction peaks indicated that yttria-stabilized zirconia crystallized in tetragonal structure for both slip casted(SC) and fused deposition modelled(FDM) samples. Further, scanning electron microscopy of slip casted sample showcased closely packed structure with fine grains and an average grain size of ∼65 nm whilst fused deposition modelled samples showcased non-homogeneous pores with ∼20 nm grain size. Average relative density of slip casted samples was ∼99.4 % while that of fused deposition modelled sample exhibited ∼96.2 %. The Vickers Hardness of slip casted (∼15.26 ± 0.4 GPa) was ∼10 % higher than the fused deposition modelled samples (∼13.79 ± 0.3 GPa). Likewise, indentation fracture toughness of slip casted (5.78 ± 0.5 MPa m1/2) was 14 % higher than fused deposition modelled samples which could have been due to the change in grain size as well as porosity of the ceramics. Compressive strength of the fused deposition modelled samples was 32 % less than slip casted samples (∼510 ± 10 MPa) due to its non-homogenous pores which led to weakening van der Waals force of attraction.

RESUMEN

6061 aluminum composites with 0.5 and 1 vol. % graphene nanoplatelets as well as 1 and 2 vol. % activated nanocarbon were manufactured by a powder metallurgy method. Scanning electron microscopy and Raman spectroscopy were used to study the morphology, structure, and distribution of nanocarbon reinforcements in the composite samples. Density Functional Theory (DFT) calculations were performed to understand the aluminum-carbon bonding and the effects of hybridized networks of carbon atoms on nanocarbon aluminum matrix composites. Scanning electron microscopy showed the good distribution and low agglomeration tendencies of nanoparticles in the composites. The formation of secondary phases at the materials interface was not detected in the hot-pressed composites. Raman spectroscopy showed structural changes in the reinforced composites after the manufacturing process. The results from Density Functional Theory calculations suggest that it is thermodynamically possible to form carbon rings in the aluminum matrix, which may be responsible for the improved mechanical strength. Our results also suggest that these carbon networks are graphene-like, which also agrees with the Raman spectroscopy data. Micro-Vickers hardness and compressive tests were used to determine the mechanical properties of the samples. Composites presented enhanced hardness, yield and ultimate strength compared to the 6061 aluminum alloy with no nanocarbon reinforcement. Ductility was also affected, as shown by the reduction in elongation and by the number of dimples in the fractured surfaces of the materials.

RESUMEN

The aim of this study was to evaluate the surface properties and fatigue mechanical behavior of an advanced lithium disilicate ceramic in comparison to lithium disilicate and zirconia. First, discs (n = 15, diameter = 13.5 mm and thickness = 1.2 mm) were made from the following materials: 4Y-PSZ - 4% mol yttria-stabilized zirconia (IPS e.max ZirCAD A2); LD - lithium disilicate (IPS e.max CAD); ALD - advanced lithium disilicate (CEREC Tessera). The specimens were crystalized/sintered and subsequently analyzed by a rugosimeter (Mitutoyo SJ-410) to determine surface roughness (parameters Ra and Rz). Specimens were subjected to biaxial flexural fatigue testing using the step-test method (20 Hz; 10,000 cycles per step; initial stress of 200 MPa; and step size of 25 MPa) until specimen fracture. Statistical analyses included Shapiro-Wilk, Kruskal-Wallis, and post-hoc tests for roughness data, while survival analysis (Kaplan-Meier and Mantel-Cox) and reliability analysis (Weibull modulus) were applied to flexural fatigue strength data. Hardness (Vickers) results were submitted to analysis of variance (1-way ANOVA) and Tukey's test. Zirconia (4Y-PSZ) showed higher FFS, CFF (467 MPa and 115216 cycles) and survival compared to the other materials. ALD had the lowest FFS, CFF (215 MPa and 11,908 cycles) and survival. ALD showed lower Weibull modulus (m = 6.63 for FFS; m = 1.27 for CFF) than LD for FFS (m = 17.33), and lower than LD (m = 4.64) and 4Y-PSZ (m = 6.69) for CFF. ALD showed the lowest Ra (0.07 µm) and Rz (1.05 µm) values, while 4Y-PSZ (Ra = 0.22 µm; Rz = 1.91 µm) and LD (Ra = 0.21 µm; Rz = 2.17 µm) showed higher and similar values. Zirconia (4-YPSZ) was the hardest material, while lithia-based ceramics (LD and ALD) presented the lowest and similar hardness values. Fractures originated in surface defects in the tensile stress concentration region. ALD has lower flexural fatigue strength compared to the other tested materials, along with higher variability (lower structural reliability).

Asunto(s)

RESUMEN

Direct restorations are currently the most popular restorations used in dental prosthodontics. Due to the increased requirements for materials used in the fabrication of fixed restorations, there is a need for evaluation of strength parameters of these materials, including dental cements. The present study investigated the change in selected strength parameters of four dual-cured composite cements as a function of storage temperature. The following were investigated: three-point flexural strength (FS), flexural modulus in bending (FM), diametral tensile strength (DTS) and Vickers hardness (HV). Four dual-cured composite cements were tested, i.e., Multilink Automix (Ivoclar Vivadent), seT PP (SDI), MaxCem (Kerr), and Bifix Hybrid Abutment (VOCO). Each of the tested cements was stored for 7 days at one of the selected temperatures: 8 °C, 15 °C, 25 °C, or 35 °C, before the samples were made. Strength properties (DTS, FS) are not strongly dependent on the storage temperature in the range of 8-35 °C. Some statistical differences were observed between the hardness of MaxCem and Multilink Automix storage in various temperatures. FS and FM were lowest for Bifix Hybrid Abutment, MaxCem and Multilink Automix storage at 25 °C, and highest for Bifix Hybrid Abutment, MaxCem, and seT PP stored in 35 °C. The cement with the highest filler content (70% by weight) showed the highest FS and HV.

RESUMEN

Ocean acidification (OA) results from the absorption of anthropogenic CO2 emissions by the ocean and threatens the survival of many marine calcareous organisms including molluscs. We studied OA effects on adult shells of the abalone species Haliotis diversicolor and Haliotis discus hannai that were exposed to three pCO2 conditions (ambient, ∼880, and ∼1600 µatm) for 1 year. Shell periostracum corrosion under OA was observed for both species. OA reduced shell hardness and altered the nacre ultrastructure in H. diversicolor, making its shells more vulnerable to crushing force. OA exposure did not reduce the shell hardness of H. discus hannai and did not alter nacre ultrastructure. However, the reduced calcification also decreased its resistance to crushing force. Sr/Ca in the shell increased with rising calcification rate. Mg/Ca increased upon OA exposure could be due to a complimentary mechanism of preventing shell hardness further reduced. The Na/Ca distribution between the aragonite and calcite of abalone shells was also changed by OA. In general, both abalone species are at a greater risk in a more acidified ocean. Their shells may not provide sufficient protection from predators or to transportation stress in aquaculture.

Asunto(s)

RESUMEN

Zirconium-lithium-phosphate glasses were elaborated through the melting-quenching technique. The primary objective of this research is to investigate how the replacement of lithium oxide with zirconium oxide impacts the physical, thermal, mechanical, and electrical properties of the fabricated glasses. The result showed that the vitreous materials were obtained with a ZrO2 content lower than 1 mol%. Furthermore, it is found that incorporating ZrO2 in the glassy phosphate framework affects mal compatibility and increases the durability of the glassy samples. Analyzing the mechanical performance reveals that the incorporation of ZrO2 leads to enhancements in the elastic constants of the glasses, including the longitudinal modulus, shear modulus, Young's modulus, bulk modulus, and Poisson coefficient. The bond strengths are used to calculate and explain the glasses' Vickers hardness values. On the other hand, the infrared (IR) spectroscopy results reveal that replacing Li2O with ZrO2 oxide in the glassy matrix causes significant structural changes. Finally, the dielectric features of the prepared glasses versus frequency and temperature are analyzed. The significance lies in the fact that the replacement of lithium with zirconium leads to a reduction in the ionic conductivity of the glasses.

RESUMEN

Background: Mouthwashes are increasingly being used worldwide. However, these preparations are known to have a negative impact on composite resin dental restorations. In this study, we aim to evaluate the effect of mouthwashes on the microhardness of such restorations. Methods: Thirty specimens of Tetric NCeram composite were prepared. Each composite specimen was cured for 40 seconds and kept in saline solution for 24 hours at 37 °C. Baseline microhardness of each specimen was recorded using an Innovatest Vickers Micro Hardness Tester. Composite specimens were randomly placed in 20 mL of the selected mouthwashes (Colgate® Plax, Listerine® Teeth & Gum Defence, and Closeup® Antibacterial Mouthwash Cool Breeze) and stored in an incubator for 24 hours at 37 °C. Next, microhardness values were rechecked. pH measurements were recorded for each type of mouthwash using a digital pH meter. Results: Due to the acidic nature of Colgate® and Listerine®, the microhardness of the restorations decreased with these mouthwashes; Listerine® caused the greatest decrease in microhardness and had the lowest pH reading (4.34). For Closeup®, with a neutral pH (7.02), no negative effect on microhardness was found; on the contrary, due to the presence of zinc in this latter mouthwash, an increase of the microhardness was found. Conclusions: We confirm the negative effect of acidic mouthwashes on the microhardness of composite dental restorations.(AU)

Fundamento: El uso de colutorios bucales está aumentando a nivel mundial. Sin embargo, es conocido que afectan negativamente a las reparaciones dentales de composite, por lo que el objetivo de este estudio es evaluar el efecto de los colutorios bucales sobre la microdureza de estas reparaciones. Métodos: Se prepararon treinta muestras de composite Tetric NCeram. Cada muestra compuesta se curó durante 40 segundos y se mantuvo en solución salina durante 24 horas a 37 °C. La microdureza inicial de cada muestra se registró utilizando un probador de microdureza Innovatest Vickers. Las muestras se sumergieron aleatoriamente en 20 mL de los colutorios bucales seleccionados (Colgate® Plax, Listerine® Teeth & Gum Defence y Closeup® Antibacterial Mouthwash Cool Breeze) y se incubaron a 37 °C durante 24 horas. A continuación, se volvieron a comprobar los valores de microdureza. El pH de cada colutorio bucal empleado se midió con un pHmetro digital. Resultados: Debido a la naturaleza ácida de Colgate® y Listerine®, la microdureza de las muestras de composite sumergidas en estos colutorios disminuyó; Listerine® causó la mayor disminución de microdureza y mostró el pH más bajo (4,34). Closeup®, con pH neutro (7,02), no mostró ningún efecto negativo sobre la microdureza; por el contrario, su contenido en zinc aumentó la microdureza de las muestras. Conclusiones: Los colutorios bucales ácidos mostraron un efecto negativo sobre la microdureza de las restauraciones dentales de composite.(AU)

Asunto(s)

RESUMEN

CONTEXT: This study rigorously investigates three 3d transition metal carbide (TMC) structures via LDA and GGA approximations. It examines cohesive energy (Ecoh), Vickers hardness (Hv), mechanical stability, and electronic properties. Notably, most 3d TMCs exhibit higher cohesive energy than nitrides, and rs-TiC demonstrates a Vickers hardness of 25.66 GPa, outperforming its nitride counterpart. The study employs theoretical calculations to expedite research, revealing mechanical stability in CrC and MnC (GGA) and CrC (LDA in cc structure), while all 3d TMCs in rs and seven in zb structures show stability. Charge transfer and bonding analysis reveal enhanced covalency along the series, influenced by the interplay between p orbitals of carbon and d orbitals of the metal. Most 3d TMCs exhibit metallic properties, excluding zb-TiC and zb-FeC in all phases. An inverse correlation between elastic constant C44 and electronic states near the Fermi level (EF) emerges, guiding applications and design. This study efficiently uncovers 3d TMC properties, offering insights for applications and design. METHODS: We employed the Vienna ab initio Simulation software (VASP) to perform computations based on density functional theory (DFT). Our approach incorporated both the projector augmented wave (PAW) and PW91 general gradient approximation (GGA) methods within the local density approximation (LDA).

RESUMEN

Monolithic dental prostheses made of 3-6 mol% yttria-stabilized zirconia (3-6YSZ) have gained popularity owing to their improved material properties and semi-automated fabrication processes. In this study, we aimed to evaluate the influence of mechanical surface treatments, such as polishing, grinding, and sandblasting, on the residual stress of 3-6YSZ used for monolithic prostheses in association with crystalline phase transformation. Plate specimens were prepared from five dental zirconia blocks: Aadva Zirconia ST (3YSZ), Aadva Zirconia NT (6YSZ), Katana HT (4YSZ), Katana STML (5YSZ), and Katana UTML (6YSZ). The specimens were either polished using 1, 3, or 9 µm diamond suspensions, ground using 15, 35, or 55 µm diamond discs, or sandblasted at 0.2, 0.3, or 0.4 MPa. The residual stress, crystalline phase, and hardness were analyzed using the cosα method, X-ray diffraction (XRD), and Vickers hardness test, respectively. Additionally, we analyzed the residual stress on the surfaces of monolithic zirconia crowns (MZCs) made of 4YSZ, 5YSZ, and 6YSZ, which were processed using clinically relevant procedures, including manual grinding, followed by polishing using a dental electric motor on the external surface, and sandblasting on the internal surface. Residual stress analysis demonstrated that grinding and sandblasting, particularly the latter, resulted in the generation of compressive residual stress on the surfaces of the plate specimens. XRD revealed that the ground and sandblasted specimens contained a larger amount of the rhombohedral phase than that of the polished specimens, which may be a cause of the residual stress. Sandblasting significantly increased the Vickers hardness compared to polishing, which may possibly be due to the generation of compressive residual stress. In the case of MZCs, compressive residual stress was detected not only on the sandblasted surface, but also on the polished surface. The difference in the residual stress between the plate and crown specimens may be related to the force applied during the automated and manual grinding and polishing procedures. Further studies are required to elucidate the effects of the compressive residual stress on the clinical performance of MZCs.

Asunto(s)