RESUMEN

BACKGROUND: Advancements in digital dentistry helped in custom-milling screw-channels in implant-supported restorations; however, the fit of these restorations is still unclear especially for contemporary computer aided designing/computer aided manufacturing (CAD/CAM) materials. This study aimed to compare the internal and marginal fit of Ultra translucent multilayered zirconia versus lithium disilicate implant-supported hybrid abutment crowns (HACs) constructed with custom-milled screw-channels on Titanium-base. MATERIALS AND METHODS: A total of 24 HACs with custom-milled screw-channels were constructed from lithium disilicate (Group LDS) and Ultra translucent multilayered zirconia (Group UT) using digital workflow (n = 12). The internal and marginal gaps of HACs on their corresponding Titanium-bases were assessed using replica technique and stereomicroscope, respectively. After testing for normality, quantitative data were expressed as mean and standard deviation and compared using independent t-test at a level of significance (P ≤ 0.05). RESULTS: There was no statistically significant difference between Group LDS and Group UT in terms of marginal and internal fit. The internal and marginal gaps in both groups were within the accepted values reported in literature. CONCLUSIONS: UT and LDS HACs with custom-milled screw-channels demonstrated comparable and acceptable internal fit and marginal adaptations to Ti-base, which lied within the range reported in literature.

Asunto(s)

RESUMEN

Objectives: To investigate the effect of different designs of movable parts and prosthetic materials on the stress distribution of supporting tissues in mandibular free end dentition defects using three-dimensional finite element analysis of digital Roach attachments. Material and methods: A 3D model of a patient with Kennedy class I mandibular edentulous conditions was generated, and twelve prosthesis models were applied, combining two designs of removable parts and six types of CAD/CAM restorative materials with different elastic modulus (conventional zirconia, ultra-translucent zirconia, Polyetheretherketone (PEEK), Lithium disilicate, Nanoceramic resin, and resin composite (Paradigm MZ100, 3 M ESPE)). The stress distribution of abutment periodontal ligament, edentulousmucosa, and junction of attachment were analyzed using finite element analysis. Results: The stress value of the buccal neck of the periodontal ligament and the maximum compressive stress of the distal periodontal ligament of the design with clasp arms were higher than those without clasp arms, while the stress on the junction of attachment and the displacement of the mucosa in the edentulous area were smaller. Restorative materials with high elastic modulus, such as conventional zirconia and ultra-translucent zirconia, are recommended to be used as the fixed part of Roach attachment. Conclusion: CAD/CAM Roach attachments with clasp arms are recommended for the protection of mucosal soft tissue. Restorative materials with high elastic modulus, such as conventional zirconia and ultra-translucent zirconia, are recommended as the fixed part of Roach attachment for patients with free end defect of mandibular dentition. Clinical significance: This study provides references for the design with clasp arms and the selection of clinical fixed-movable prosthetic materials. Clinicians should consider the design of attachments and selection of appropriate manufacturing materials carefully to avoid negative impacts on patients' periodontal support tissues.

RESUMEN

Monolithic dental prostheses fabricated from 3 mol.% yttria-stabilized zirconia (3YZ) are becoming increasingly popular. Recently, 5 mol.% yttria-stabilized zirconia (5YZ) which significantly improves the translucency of 3YZ has been prepared. However, its mechanical and microstructural properties, especially those affected by low-temperature degradation (LTD), have not been fully elucidated yet. The objective of the present study was to establish the relationship between the flexural strength of 5YZ with or without autoclave-induced LTD and its microstructural properties. For this purpose, a total of 320 bar-shaped specimens were cut from 5YZ and 3YZ blocks, and half of the specimens in each group were autoclaved at 134 °C for 50 h. Their flexural strengths were determined by conducting three-point bending tests, and the obtained results were analyzed by the Weibull statistical method. Grain sizes and crystalline structures of the specimens were analyzed by scanning electron microscopy (SEM) and X-ray diffraction, respectively. Additionally, the LTD-induced phase transformation was examined by Raman microscopy and cross-sectional surface analysis. The characteristic strengths of 5YZ and 3YZ were approximately 620 and 950 MPa, respectively, and 5YZ was found to be more resistant to LTD in terms of phase transformation than 3YZ. However, a low amount of the monoclinic phase was detected even in 5YZ after 50 h of autoclaving, which significantly decreased its flexural strength and reliability. The results of SEM analysis revealed that 5YZ was composed of two distinct regions: a dominant matrix with large grains (median size: 0.8 µm) and scattered areas with small grains (median size: 0.4 µm). Phase transformation analysis and fractography data indicated that the small-grain region was strongly affected by LTD and likely represented a fracture origin. The described properties should be considered during the clinical application of monolithic 5YZ dental prostheses.

Asunto(s)

RESUMEN

Background . The current study aimed at identifying the color agreement between try-in pastes and the respective resin cements and investigated the effect of thickness and regions of Ultra-Translucent Multilayered Zirconia Veneers. Methods . A total of 90 cubic zirconia discs were prepared at two different thicknesses (0.5 mm and 0.7 mm) (n=45) in five groups in terms of the shade of the try-in paste and resin cement as follows: Universal, Clear, Brown, White and Opaque. Try-in paste and the respective resin cement were applied between the specimens and composite substrate, respectively, and colorimetric evaluation was carried out using CIE-Lab system. For each specimen, ΔE between the try-in paste and cement was calculated. Data were analyzed with SPSS 17 using Multifactor ANOVA (P<0.05). Results . Multifactor ANOVA results showed that ΔE values were significantly affected by the resin cement shade and the thickness of ceramic veneer (P<0.05). The results showed better shade agreement between the try-in paste and the respective resin cement with thicker ceramic veneers. The results of Tukey HSD revealed that ΔE values for the Clear, Universal and Brown shades were less than those of the White and Opaque shades. Lighter shades exhibited better agreement between the try-in paste and the respective resin cement. Conclusion . Perceptible color difference was found between the try-in pastes and the respective resin cement in most colors investigated. Although, the agreement of the try-in pastes and the respective resin cement was affected by the thickness of zirconia veneers, the different regions of multilayered ultra-translucent zirconia ceramic showed no significant effect.

RESUMEN

OBJECTIVE: The aim of this study was to evaluate the load-bearing capacity of monolithic lithium disilicate (LiDi - IPS e.max CAD) and novel ultra-translucent zirconia restorative systems of various compositions: 5Y-PSZ (5 mol% yttria-partially-stabilized zirconia) and 4Y-PSZ (4 mol% yttria-partially-stabilized zirconia); relative to a 3Y-TZP (3 mol% yttria-stabilized zirconia) control. MATERIALS AND METHODS: Experiments were carried out with 10 disc specimens (Ø12 ×1 mm) per ceramic material. The zirconia intaglio surface (as machined) was sandblasted (50 µm Al2O3 at 2 bar), while LiDi was etched with 5% HF for 20 s. The ceramic discs were then adhesively bonded onto a dentin-like substrate (G10, a high-pressure fiberglass material) using Multilink Automix cement and Monobond Plus primer, producing a ceramic/cement/dentin-like substrate trilayer structure. The bonded specimens were stored in water for 3 days at 37 °C prior to a Hertzian indentation flexural radial fracture test. The plate-on-foundation theory was used to validate the load-bearing capacity of the trilayer systems based on the flexural tensile stress at the ceramic intaglio (cementation) surface-a cause for bulk fracture of ceramic onlays. RESULTS: The experiment data showed that, when bonded to and supported by a dentin-like substrate, the load-bearing capacity of LiDi (872 N) is superior to the 5Y-PSZ (715 N) and can even reach that of 4Y-PSZ (864 N), while 3Y-TZP still holds the highest load-bearing capacity (1195 N). Theoretical analyses agree with experimental observations. The translucency of 5Y-PSZ approaches that of LiDi, which are superior to both 4Y-PSZ and 3Y-TZP. CONCLUSIONS: When adhesively bonded to and supported by dentin, lithium disilicate exhibits similar load-bearing properties to 4Y-PSZ but much better than 5Y-PSZ.

Asunto(s)