RESUMEN

Background and objectives: wear and corrosion can lead to the gross failure of the Morse taper junction with the consequent fracture of the true neck of the prosthetic stem in hip arthroplasty. Materials and Methods: 58-year-old male patient, with a BMI of 38 kg/m2. Because of avascular necrosis, in 2007, a metal-on-metal total hip arthroplasty was implanted in him, with a TMZF stem and a Co-Cr head. In December 2020, he complained of acute left hip pain associated with the deterioration of his left leg and total functional impairment, preceded by the crunching of the hip. X-rays and CT scan showed a fracture of the prosthetic neck that necessitated prosthetic revision surgery. A Scanning Electron Microscope (SEM) analysis of the retrieved prosthetic components was conducted. Results: Macroscopically, the trunnion showed a typical bird beak appearance, due to a massive material loss of about half of its volume. The gross material loss apparently due to abrasion extended beyond the trunnion to the point of failure on the true neck about half a centimeter distal from the taper. SEM analysis demonstrated fatigue rupture modes, and the crack began close to the neck's surface. On the lateral surface, several scratches were found, suggesting an intense wear that could be due to abrasion. Conclusions: The analysis we conducted on the explanted THA showed a ductile rupture, began close to the upper surface of the prosthetic neck where the presence of many scratches had concentrated stresses and led to a fatigue fracture.

Asunto(s)

RESUMEN

INTRODUCTION: Trunnionosis of total hip prosthesis is defined as corrosion at the head-neck taper junction combined with local tissue reaction. Trunnionosis is a rare complication of total hip arthroplasty (THA) that is often missed in diagnosis. Severe trunnionosis can result in head-neck dissociation, which is called gross trunnion failure (GTF). CASE PRESENTATION: We describe a case of GTF in a 70-year-old male patient 10 years after right total hip arthroplasty with a cobalt chromium (CoCr) femoral head and a titanium alloy stem. A revision of the stem, cup and femoral head was performed. Six months after surgery, the patient is recovering well and walking. DISCUSSION: Trunnionosis is associated with hip prostheses with a CoCr femoral head and a titanium alloy stem. Metal Artefact Reduction Sequence (MARS) and serum cobalt and chromium levels are diagnostic tools that can be useful when trunnionosis is suspected. CONCLUSION: Trunnionosis remains hard to diagnose in an early stage when gross trunnion failure is not present. This case of a 70-year-old patient with gross trunnion failure 10 years after right total hip arthroplasty supports the literature suggesting that a CoCr femoral head, a high body mass index (BMI), and a longer implantation time are risk factors for developing trunnionosis. When conventional X ray and C-reactive protein are inconclusive, serum cobalt and chromium levels should be determined. When serum cobalt and chromium levels are elevated, a MARS MRI should be performed to confirm trunnionosis.

RESUMEN

Metallosis is a known yet rare late complication of unicompartmental and total knee arthroplasty (TKA), usually secondary to either metal-backed patellar component failure, mobile-bearing polyethylene dislocation, or catastrophic polyethylene failure and wear through. The majority of literature surrounding metallosis has been published in relation to total hip arthroplasty (THA) metal on metal bearing wear or mechanically assisted crevice corrosion.This case report describes the development of metallosis in a 77-year-old male patient with advanced (Kellgren-Lawrence Grade 4) osteoarthritis with associated valgus deformity, who underwent index TKA with a semiconstrained revision knee system due to intraoperative medial collateral ligament laxity. The taper junction between the titanium alloy stem and cobalt chromium femoral component was the source of diffuse intra-articular metallosis.

Asunto(s)

RESUMEN

BACKGROUND: Ceramic heads are frequently combined with titanium sleeves in revision total hip arthroplasties (THAs), ostensibly to protect the ceramic head from existing damage to the retained trunnion. Although widely adopted, data on the performance and safety of this construct are minimal. The purpose of this study was to describe implant survivorships, radiographic results, and clinical outcomes of patients who underwent revision THA with a ceramic head and titanium sleeve on a retained femoral component. METHODS: We identified 516 revision THAs with femoral component retention (328 acetabular-only revisions and 188 bearing surface exchanges) treated with a new ceramic head and titanium sleeve between 2000 and 2020. Mean age at revision was 64 years, 56% were women, and mean body mass index was 30. The indications for revision THA were adverse local tissue reaction (25%), acetabular loosening (24%), dislocation (17%), infection (5%), and other (29%). Kaplan-Meier survivorships were analyzed, radiographs reviewed, and Harris Hip Scores evaluated. Mean follow-up was 4 years (range, 2 to 10). RESULTS: There were no reoperations or failures for ceramic head fracture, taper corrosion, or head/sleeve disengagement. The 10-year survivorship free of any re-revision was 85%. Indications for the 57 re-revisions included dislocation (33), infection (13), acetabular component loosening (7), periprosthetic fracture (2), psoas impingement (1), and sciatic nerve irritation (1). The 10-year survivorship free of any reoperation was 82%. There were an additional 14 reoperations. Radiographically, 1.9% had progressive femoral radiolucent lines, and 4.7% had progressive acetabular radiolucent lines. Mean Harris Hip Score was 81 at 2 years. CONCLUSIONS: New ceramic heads with titanium sleeves in revision THAs with retained femoral components were durable and reliable with no cases of ceramic head fracture or taper complications at mean 4-year follow-up, including those revised for adverse local tissue reaction. LEVEL OF EVIDENCE: IV.

Asunto(s)

RESUMEN

Femoral neck trunnion dissociations are rare complications of total hip replacements. This hardware failure is often due to underlying trunnionosis which is important to recognize. We present a case of a patient with dissociation at the femoral head-neck junction of a total hip arthroplasty (THA) with a Stryker Accolade TMZF femoral stem. There was no significant preceding trauma. The complication was visualized on radiography and confirmed during revision arthroplasty.

RESUMEN

A 67-year-old man who underwent right hemiarthroplasty and left total hip arthroplasty (THA) experienced left hip pain two years previously. No previous diagnosis was made at other hospitals. Radiography revealed left hip trunnionosis because of stem-neck shortening, with periprosthetic joint infection (PJI) spreading to both hips. Bilateral revision THA was performed, but the treatment was difficult due to the delayed diagnosis, necessitating the extraction of the well-fixed stem for PJI. Trunnionosis is caused by implant-related, surgical, and patient factors, and early diagnosis is important because of its association with PJI. Furthermore, even implants with few reports of trunnionosis can lead to this complication. Surgeons should always consider that performing THA using a large-diameter head predisposes the patient to trunnionosis.

RESUMEN

BACKGROUND: Corrosion at the head-neck junction of femoral stems is a rare complication of total hip arthroplasty (THA) with manifestations ranging from subclinical wear to failure. Prior studies have identified a single femoral component design with an increased propensity for catastrophic trunnion failure. The purpose of the present study was to quantify trunnion damage of this femoral component retrieved from patients undergoing revision THA for non-trunnionosis indications. METHODS: 24 femoral components from a single manufacturer were identified for study inclusion. Each prosthesis underwent stereomicroscopic inspection. Corrosion and fretting scores were assigned per the Goldberg criteria to quadrants of the trunnion. Material loss was calculated based on cone angles across trunnion quadrants. This was carried out using a coordinate measuring machine that digitised each trunnion surface. Stems were compared to a series of femoral stems with the same trunnion design. RESULTS: 20 of the 24 (83%) trunnions demonstrated corrosion, all 24 trunnions demonstrated fretting. Corrosion scores did not statistically differ with respect to trunnion zone (p = 0.53), while fretting scores were higher in the inferior compared to the superior zones (p < 0.001). There was no significant difference in cone angles assessing material loss between stems (p = 0.25). CONCLUSIONS: Evidence of trunnion damage was observed in each stem retrieved for non-trunnionosis revision. Fretting occurred more frequently about the inferior quadrants. However, digitised trunnion shapes were similar between compared stems exhibiting no material loss. Therefore, it is possible that previous reports of trunnion failures for this implant are not a systemic issue, and that further investigation is required.

RESUMEN

INTRODUCTION AND IMPORTANCE: Several studies have discussed trunnionosis in metal-on-metal total hip arthroplasties. However, trunnionosis in metal-on-polyethylene total hip arthroplasties has been less frequently discussed. CASE PRESENTATION: In this study, trunnionosis in two male patients undergoing metal-on-polyethylene total hip arthroplasty, which was done to treat femoral head osteonecrosis were reported and discussed adequately. CLINICAL DISCUSSION: Total hip arthroplasties (THA) were done for the treatment of femoral head osteonecrosis in these cases. In the first case, trunnionosis occurred one year after the revision of the primary THA, and in the second case occurred ten years after the primary THA. Both of these cases were presented with reduced range of motion. After surgery, the symptoms were resolved, and the patients remained complication-free until the last follow-up. CONCLUSION: This report raises awareness regarding the importance of trunnionosis as a serious complication of modular total hip arthroplasty.

RESUMEN

Corrosion at the modular head-neck taper interface of total and hemiarthroplasty hip implants (trunnionosis) is a cause of implant failure and clinical concern. The Goldberg corrosion scoring method is considered the gold standard for observing trunnionosis, but it is labor-intensive to perform. This limits the quantity of implants retrieval studies typically analyze. Machine learning, particularly convolutional neural networks, have been used in various medical imaging applications and corrosion detection applications to help reduce repetitive and tedious image identification tasks. 725 retrieved modular femoral stem arthroplasty devices had their trunnion imaged in four positions and scored by an observer. A convolutional neural network was designed and trained from scratch using the images. There were four classes, each representing one of the established Goldberg corrosion classes. The composition of the classes were as follows: class 1 (n = 1228), class 2 (n = 1225), class 3 (n = 335), and class 4 (n = 102). The convolutional neural network utilized a single convolutional layer and RGB coloring. The convolutional neural network was able to distinguish no and mild corrosion (classes 1 and 2) from moderate and severe corrosion (classes 3 and 4) with an accuracy of 98.32%, a class 1 and 2 sensitivity of 0.9881, a class 3 and 4 sensitivity of 0.9556 and an area under the curve of 0.9740. This convolutional neural network may be used as a screening tool to identify retrieved modular hip arthroplasty device trunnions for further study and the presence of moderate and severe corrosion with high reliability, reducing the burden on skilled observers.

Asunto(s)

RESUMEN

BACKGROUND: The aim of this study is to update the 10-year follow-up survivorship and metal ions levels of a cohort of metal-on-metal (MoM) hip resurfacing (HR) and large-diameter-head (LDH) total hip arthroplasty (THA). METHODS: The study is a retrospective analysis of prospectively collected data that compared the outcomes of 24 MoM HR (21 patients) and 15 (11 patients) modular LHD MoM THA at >10 years follow-up. Baseline characteristics as well as intraoperative and postoperative information were collected, including complications, revisions, clinical and radiographic outcomes, and serum metal ions level (Cobalt, Chromium). Metal ion levels were compared using a two-tailed unpaired t-test and Wilcoxon signed-rank test (jamovi v2.3.3.0, Sydney, NSW, AU). RESULTS: No significant differences were detected in gender, BMI, and ASA score between the two groups. Patients in the modular THA group were significantly older (57 years vs. 46 years; p < 0.05). The HR overall survivorship was 91.7% (22 of 24 hips) with survivorship from implant failure and/or aseptic loosening and/or metal debris related 100% of problems. The modular THA overall survivorship was 86.7% (13 of 15 hips) with survivorship from implant aseptic loosening and metal ions complications of 93.4% (14 of 15 hips). No significant difference was noted when comparing clinical outcomes. Metal ions were significantly lower in the HR group (Co 25.8 nmol/L vs. 89 nmol/L; p < 0.001-Cr 33.5 nmol/L vs. 55.2 nmol/L; p = 0.026). CONCLUSION: Both implants reported excellent and comparable clinical outcomes at >10 years follow-up. The Adept HR reported remarkable survivorship, in line with the registry data, proving once again its reliability in young active males. The modular LDH THA, despite being discontinued, presented higher reliability and a lower failure rate when compared with similar withdrawn MoM implants. Trunnionosis did not appear to be a significant problem in this particular modular design.

RESUMEN

The use of inert head materials such as ceramic heads has been proposed as a method of reducing wear and corrosion products from the articulating surfaces in total hip arthroplasty, as well as from the stem-head taper connection. The aim of the present study was to compare the blood metal ion levels in patients with Oxinium and CoCrMo modular femoral heads, as well as monoblock stainless steel Charnley prostheses at 10 years postoperatively. The 150 patients with osteoarthritis of the hip joint included in a randomized clinical trial were grouped according to femoral head material. One group (n = 30) had received the Charnley monoblock stainless steel stem (DePuy, UK). The other patients (n = 120) received a Spectron EF CoCrMo stem with either a 28 mm CoCrMo or Oxinium modular head (Smith & Nephew, USA). After 10 years, 38 patients had withdrawn, 19 deceased, 7 revised due to aseptic loosening and 5 revised due to infection. The 81 patients with median age of 79 years (70-91) were available for whole blood metal ion analysis. The levels of Co, Cr, Ni and Zr in the blood were generally low with all the head materials (medians <0.3 micrograms/L) and no statistical difference between the groups were found (p = .2-.8). Based on the low blood metal ion values in our study groups, no indication of severe trunnion corrosion in patients with CoCrMo heads was observed, neither was there any beneficial reduction in metal ion exposure with the Oxinium femoral heads.

Asunto(s)

RESUMEN

A 64-year-old male with a recalled modular-neck stem implant presented with a soft tissue mass in the lateral thigh. Preoperative testing revealed no signs of infection by the 2018 periprosthetic joint infection criteria. MRI revealed a large soft tissue mass around the implant consistent with a pseudotumor, and we performed revision surgery of the femoral component for trunnionosis. One intraoperative culture was positive for infection, and the patient was placed on antibiotics. Six weeks following revision surgery of the femoral component, the patient presented with acute drainage and was diagnosed with an acute on chronic periprosthetic joint infection and underwent explantation of the femoral and acetabular components with the placement of an antibiotic spacer. Cultures revealed identical bacteria from the index procedure. Given the clinical course, this case likely represents adverse local tissue reaction with an atypical presentation of periprosthetic joint infection. This is the first case presentation of an adverse local tissue reaction and superimposed periprosthetic joint infection with normal infection workup, representing an important consideration when differentiating between pseudotumor and periprosthetic joint infection in modular-neck femoral stem implants.

RESUMEN

In vitro test methods are challenged by the multi-factorial nature of head-neck taper connection tribocorrosion due to the consequences of simplification. Incorrect study design and misinterpretation of results has led to contradictory findings regarding important factors affecting head-neck taper tribocorrosion. This review seeks to highlight important considerations when developing in vitro test methods, to help researchers strengthen their study design and analyze the implications of others' design decisions. The advantages, disadvantages, limitations and procedural considerations for finite element analyses, electrochemical studies and in vitro simulations related to head-neck taper connection tribocorrosion are discussed. Finite element analysis offers an efficient method for studying large ranges of mechanical parameters. However, they are limited by neglecting electrochemical, biological and fluid flow factors. Electrochemical studies may be preferred if these factors are considered important. Care must be taken in interpreting data from electrochemical studies, particularly when different materials are compared. Differences in material valence and toxicity affect clinical translation of electrochemical studies' results. At their most complex, electrochemical studies attempt to simulate all aspects of headneck taper connection tribocorrosion in a bench top study. Effective execution requires in-depth knowledge of the tribocorrosion phenomenon, the involved mechanisms, and their measures such that each study design decision is fully informed.

RESUMEN

BACKGROUND: This study aimed to examine the medium-term clinical and radiological outcomes of revision THA using the S-ROM-A stem, a modification of the S-ROM stem intended for Asians. METHODS: Femoral reconstruction using the S-ROM-A stem was performed in 126 hips that underwent revision THA. All patients were followed for perioperative complications. In addition, clinical and radiographic outcomes at a mean of 8 (range 5-14) years postoperatively were evaluated in 96 hips of 86 patients (76%). RESULTS: The most common perioperative complication was a femoral fracture, occurring in 16 hips (13%), including 11 intraoperative and 5 postoperative fractures. Dislocation occurred in five hips (4.0%), infection in three hips (2.4%), and trunnionosis in two hips (1.6%), including late complications. The total second stem revision was performed in two hips while stem only second revision preserving the bone ingrown sleeve was performed in four hips. With a second revision for aseptic loosening as the endpoint, the 13-year stem survival rate was 100%. Hip function as assessed by the Japanese Orthopedic Association score improved from a mean of 48 points preoperatively to 87 points 8 years postoperatively (P < .05). Radiological evaluation at the final follow-up showed that 95 hips (99%) achieved bone ingrowth fixation and one hip (1%) achieved fibrous stable status. CONCLUSION: Revision THA using the S-ROM-A stem resulted in good medium-term outcomes. Although modifications of the stem length and shape may be effective in preventing fractures in Asians with relatively small body sizes, attention should be paid to the occurrence of trunnionosis, which may be associated with the decreased taper size.

Asunto(s)

RESUMEN

Approximately 17 years after a primary metal-on-metal total hip arthroplasty, a 59-year-old female developed pain, swelling, and weakness in her right hip accompanied by laboratory findings and imaging suggestive of an adverse local tissue reaction. Acetabular revision was performed to upsize the femoral head and improve hip stability. Upon impaction of the new, non-option ceramic femoral head onto the unsleeved retained stem, the head split into two pieces without fragmentation. The surgery was completed using a cobalt-chromium head, which was impacted without issue onto the stem's taper. Although BIOLOX delta femoral heads do not require titanium sleeves, we believe that careful consideration should be given to their use in revision total hip arthroplasty with ceramic heads, regardless of the extent of trunnion damage noted intraoperatively.

RESUMEN

BACKGROUND: Gross taper failure (GTF) is a rare but catastrophic failure mode of the head-stem-taper junction of hip prostheses, facilitated by massive material loss. GTF is a two stage process initiated by corrosion leading to head bottoming out, followed by abrasive wear due to the head rotating on the stem. The purpose of this study was to reproduce the clinical failure patterns and to determine the material loss during simulated gait. METHODS: Six cobalt-chromium alloy heads (36 mm, 12/14 taper) with three different head lengths (short / medium / extra long) were combined with stem taper replicas made from titanium alloy sized to achieve bottoming out. A hip simulator was used to simulate gait loading after (ISO 14242-1 for 2 million cycles). RESULTS: Wear patterns from in-vitro testing match the clinical failure patterns. Stem taper wear increased linearly with time (p< 0.001). After two million cycles the material loss of short / medium / extra long heads was (M+-STD) 1168±242 mg / 400±23 mg / 94±12 mg on the stem side and 46±36 mg / 46±24 mg / 70±8 mg on the head side. Stem taper wear decreased with increasing head length (p=0.01), whereas clinical failures are mostly seen for long and extra long heads.

Asunto(s)

RESUMEN

INTRODUCTION: Comparison of mid- to long-term cause of failure and survivorship of metal-on-metal (MoM) resurfacing hip arthroplasty (RHA) and large head total hip arthroplasty (THA) remains sparse. This study aimed to identify and compare the cause of failure and survivorship of MoM RHA and THA at a minimum ten year follow-up. METHODS: Four hundred twenty-seven MoM hip arthroplasties (286 THA and 141 RHA) were retrospectively analyzed at a mean follow-up of 13 ± three years. Causes of failure were reported as MoM specific (i.e., adverse reaction to metal debris (ARMD) and painful hip with ion elevation) or MoM non-specific (i.e., fracture, infection, and dislocation). Chromium (Cr) and cobalt (Co) ion levels and Co/Cr ratio were compared. Survivorship was compared according to the cause of failure with revision as the endpoint. RESULTS: The rate of ARMD was significantly higher in THA (OR = 2.9 [95%-CI: 1-7]; p = 0.02). No significant difference was detected in failure rate due to other causes between the two groups (p = 0.2-0.9). Ion levels and Co/Cr ratio were both significantly higher in THA (p < 0.01). Survivorship was significantly lower in THA compared to RHA at ten years [89% (95%-CI: 85%-91%) vs 96% (95%-CI: 91%-98%); p = 0.01] and 15 years [73% (95%-CI: 67%-78%) vs 83% (95%-CI: 73%-90%); p = 0.01]. CONCLUSION: RHA survivorship was significantly higher at any time point. Failure rate due to ARMD was significantly higher in THA while no significant difference in other causes of failure was observed between the two groups. This result emphasizes the role of fretting corrosion at the head-neck junction (i.e., trunnionosis) with significantly higher ion levels and Co/Cr ratio dissociation in THA.

Asunto(s)

RESUMEN

Component dissociation secondary to trunnionosis is rare, and its causes are multifactorial. It is a major complication of total hip replacement, in most cases requiring revision arthroplasty. In this paper, we present a case of taper/head modular interface dissociation in a metal-on-metal total hip replacement. We review the literature of both trunnionosis, as well as a systematic review of modular dissociation of the femoral component in total hip arthroplasty, identifying commonalities with our own case.

RESUMEN

Trunnionosis is emerging as an early mode of failure in conventional metal-on-polyethylene total hip arthroplasty. It is defined as wear or corrosion at the trunnion, the taper at the femoral head-neck interface. Trunnion wear can result in a variety of negative sequelae and, in severe cases, necessitate revision arthroplasty. We describe a 64-year-old man with a metal-on-polyethylene total hip arthroplasty who presented with a sensation of clunking in the hip. Initial imaging and laboratory studies were inconclusive, and the decision was made to monitor. Two years later, trunnion wear was detected on radiographs, presenting as an abnormal alignment of the femoral neck relative to the femoral head. Several case reports and series describe catastrophic total hip arthroplasty failure due to trunnionosis. However, few describe the radiographic signs of wear at the trunnion before gross failure. This early presentation is important to recognize to minimize patient morbidity and aid surgical planning.

RESUMEN

Adverse reaction to metal debris (ARMD) is an issue in metal-on-metal (MoM) total hip replacements (THR). It mainly affects large-head MoM THR, whereas 28-32 mm MoM pairings are associated with low long-term revision rates. However, the bearing surface is not necessarily the only cause of metal debris. This report documents with advanced analysis of the retrievals a particular cause of trunnionosis in late failure of a small diameter MoM THR and illustrates the importance of cleaning of the taper when seating the head in THR. A 65-year-old patient was revised due to ARMD 16 years after small diameter MoM THR. Debridement and exchange of the inlay and the head had been performed through an anterior approach. While the cup and the outer surface of the head were accessible to direct analysis by an optical coordinate measuring machine, the female taper had to be analysed indirectly by measuring an imprint. Wear from the cup and the head was within expected low ranges. The analysis of the female taper identified bone fragments, which contributed to trunnionosis. Failure due to ARMD after MoM THR is not necessarily caused by the bearing, but can be due to trunnionosis. Bone fragments within the taper contact in this case highlight the importance of meticulous cleaning of the taper before seating the head, to avoid trunnionosis.

Asunto(s)