RESUMEN

High-grade heavy metal elements in copper slag (CS) are worth recovering. Unfortunately, the high viscosity of leaching solution, low leaching efficiency, difficult filtration and low separation efficiency of valuable components exist in the traditional sulfuric acid leaching process. In this study, the above problems are solved by sulfuric acid pretreatment + curing + water leaching. Moreover, iron, cobalt and copper ions in solution are separated by stepwise precipitation. The final iron, cobalt, copper and silicon recoveries are 99.01 %, 98.45 %, 93.13 % and 99.52 %, respectively. Thermodynamic calculations show that H4SiO4 can be converted to insoluble SiO2 to improve filtration properties under curing conditions of sulfur dioxide partial pressures of 10-20∼0 atm, oxygen partial pressures of 10-20∼0 atm and 400-600k. Simulation studies of the phase equilibria of the components of the leach solution by Visual MINTEQ showed that the oxidation of Fe2+ to Fe3+ is necessary for the removal of Fe2+ from the solution by precipitation. This study provides a new idea for the efficient utilization of CS.

RESUMEN

Ion precipitation flotation technology was demonstrated to be an efficient method for the separation of valuable metals from low-concentration solution. However, the selective separation of three metals from mixing solution is a great challenge, and highly selective reagents are the key to polymetallic separation. In this work, stepwise separation of Co and Zn from the simulated zinc hydrometallurgy wastewater containing ternary Co-Zn-Mn metals by ion precipitation flotation process was proposed. It's demonstrated that organic reagents of 1-nitroso-2-naphthol (NN) and sodium dimethyldithiocarbamate (SDDC) had excellent selectivity for the capture of Co and Zn to form respective precipitate from wastewaters via the chelation reactions. After precipitation, dodecylpyridinium chloride (DPC) and tetradecyltrimethylammonium bromide (TTAB) were chosen as surfactants for the separation of Co and Zn sediments from the solution via the flotation process. The effects of solution pH, molar ratio, reaction temperature, and reaction time on the selective precipitation efficiencies of Co and Zn as well as the effects of surfactant dosage and flotation gas velocity on the flotation separation efficiencies were systematically investigated. It's demonstrated that the comprehensive recovery rates of Co, Mn, and Zn reach 98%, 90%, and 99%, respectively. After separation, oxidation calcination of the foam products was conducted to prepare high-purity Co3O4 and ZnO nanoparticles in which the organic matters were burnt out with gas emissions. The stepwise chelation capture mechanisms of Co and Zn by highly selective precipitation reagents were minutely discussed. It's demonstrated that the proposed selective stepwise precipitation and flotation method is suitable for recovery of critical metal ions from low-concentration polymetallic wastewaters.

Asunto(s)

RESUMEN

This work introduced a new way of fabricating a granular material with the supply of Al-rich precipitates selectively obtained from acid mine drainage (AMD), and its potential as a promising adsorbent for fluoride (F) was evaluated. Through the selective sequential precipitation (SP) process in the field, Al-rich precipitates with high purity (>81%) were collected at the high recovery rate (>99.8%) as a raw material for adsorbent fabrication. The granular adsorbent (ALB) was synthesized through encapsulation of precipitate powders by chemically inducing polymeric bead formation. The characterization results revealed that ALB possessed a highly porous structure and embedded a large number of nanoparticles of amorphous Al hydroxides inside its framework. Less adsorption of F occurred at an alkaline pH condition due to the competitive effect of hydroxyl ions. The adsorption process can be divided into fast adsorption by the outer surface and slow diffusion in the inner phase. The maximum adsorption capacity of ALB for F was calculated to be 17.7 mg g-1 in the Langmuir isotherm model fitting results. By the repetitive adsorption/desorption and XPS results, it turned out that both chemisorption and physisorption gave a contribution in the removal of F, and the regeneration of adsorbent using NaOH was effective to restore the adsorption capability but accompanied the loss of adsorption sites. As a result, it can be concluded that a granule-type material fabricated using Al-rich precipitates selectively recovered from AMD neutralization can be considered as a promising adsorbent for F removal in aqueous solution.

Asunto(s)

RESUMEN

Directional microwave-assisted liquefaction and stepwise extraction are introduced for producing platform chemicals: aromatics and monosaccharides. When sulfuric acid was used as a catalyst, a 45% monosaccharides yield and a 29% aromatics yield were obtained from bamboo with 0.3g catalyst per 18g methanol and 2g bamboo at 160°C with 10min. Approximately 78-86wt% of the six biomass materials were converted into liquid products. After the stepwise extraction and precipitation process, the yields of monosaccharide derivatives and three phenolic compound fractions were 39-45% and 28-32%, respectively. Monosaccharides from holocellulose collected with a high purity of methyl glycosides were higher than 90%. Aromatic derivatives with different weight-molecular distributions were separated into three fractions with more than 80% phenolics. As their similar chemical properties within each fraction, platform chemicals have great commercial potential for producing high-quality chemicals and biofuels using mild upgrading conditions.

Asunto(s)

RESUMEN

In this study, Ti was doped to CeO2-MoO3 to promote the catalytic performance for the selective catalytic reduction of NOx with NH3 (NH3-SCR). The preparation method for CeMo0.5TiaOx (a = 0, 1, 2, 5, 10) catalysts was a stepwise precipitation method. When Ti was doped, all of the Ce-Mo-Ti catalysts exhibited remarkably improved NOx conversion and N2 selectivity than the CeMo0.5Ox without Ti. The CeMo0.5Ti5Ox with excellent activity in a broad temperature range was selected as an optimal catalyst to investigate the effects of Ti addition. The formation process analysis of the CeMo0.5Ti5Ox showed that, the Mo and Ti species first precipitated together from the mixed solution with the increase of pH, and then Ce species precipitated onto the Mo-Ti precipitates. The obtained catalyst exhibited remarkably facilitated NOx and NH3 adsorption, enhanced charge imbalance, promoted redox property, and improved surface acidity, which are all important reasons for the excellent catalytic performance of an NH3-SCR catalyst.