RESUMEN

Steel mill wastewater sludge, as an iron-enriched solid waste, was expected to be converted into iron-enriched biochar with acceptable environmental risk by pyrolysis. The purpose of our study was to evaluate the chemical speciation transformation of heavy metals in biochar under various pyrolysis temperatures and its reutilization for tetracycline (TC) removal. The experimental data indicated that pyrolysis temperature was a key factor affecting the heavy metals speciation and bioavailability in biochar, and biochar with pyrolysis temperature at 450 °C was the most feasible for reutilization without potential risk. The endogenous iron-enriched biochar (FSB450) showed highly efficient adsorption towards TC, and its maximum adsorption capacity could reach 240.38 mg g-1, which should be attributed to its excellent mesoporous structure, abundant functional groups and endogenous iron cycling. The endogenous iron was converted to a stable iron oxide crystalline phase (Fe3O4 and MgFe2O4) by pyrolysis, which underwent a valence transition to form a coordination complex with TC by electron shuttling in the FSB450 matrix. The study provides a win-win approach for resource utilization of steel wastewater sludge and treatment of antibiotic contamination in wastewater.

Asunto(s)

RESUMEN

The American Iron and Steel Institute (AISI) gathered data between 1989 and 1997 to build an "objective database" to further understand the occupational exposures generated by the few asbestos-containing materials remaining at various steelmaking companies at this time. This paper analyzed the 520 samples from this campaign which occurred at five different steel manufacturers: Georgetown Steel Company, Inland Steel Company, Ling-Temco-Vought (LTV) Corporation, United States Steel Corporation, and Weirton Steel Corporation. This database is believed to have never previously been systematically organized. Samples were grouped based on sampling times to determine whether they should most appropriately be compared to the OSHA short-term excursion limit (EL) or the 8-hr time-weighted average (TWA) permissible exposure limit (PEL). Sampling times of 30 min or less were considered short-term samples, and samples of 180 min or greater were considered representative workday samples. Samples that did not fit into either category, with sampling times between 31 and 179 min, were considered task samples. Overall, the data indicated that the airborne concentrations were quite low in 1989 and they continued to be low through the study period which ended in 1997. Only seven out of 286 (approximately 2.5%) short-term or representative workday samples were in exceedance of the current OSHA OELs that were implemented in 1994 (short-term samples being compared to the 1 f/cc EL and representative workday samples being compared to the 0.1 f/cc 8-hr TWA PEL). Consistent with prior data, analysis of this dataset supports the view that materials containing asbestos were not used in many applications in the steel industry, and measured airborne concentrations of asbestos were almost always below the occupational exposure limits (OELs) in the post-OSHA era (1972-2000).

Asunto(s)

RESUMEN

Here, we report the complete genome sequence of Aminobacterium sp. strain MB27-C1, which was isolated from sewage sludge collected at the wastewater treatment plant of Sanming Steel Co. Ltd. in Fujian, China. The resulting genome of strain MB27-C1 is a single contig of 2,427,830 bp with 41.58% GC content.

RESUMEN

BACKGROUND: Historically, the use of asbestos in steelmaking has been limited to a few applications. Due to its physical and chemical properties, asbestos was not necessary or suitable for most purposes in a steel mill. The few applications where asbestos were used (i.e., certain gaskets, brakes, protective cloth, refractory materials, insulation materials, and hot top products) were replaced by alternative materials as they became available. OBJECTIVE: We discuss historical uses of asbestos in steel manufacturing and the associated airborne asbestos concentrations collected at sixteen U. S. Steel facilities between 1972 and 2006. METHODS: A total of 495 personal airborne asbestos samples from the U. S. Steel industrial hygiene records were analyzed across four time periods corresponding to changes in the OSHA permissible exposure limit (PEL) for asbestos. 68% of the samples (n = 337) were considered representative of an employee's workday. The remaining samples (n = 158) represented task samples. Samples were grouped by facility, department, and job category within the four time periods. RESULTS: The average fiber concentrations measured for each facility and department over time were below the contemporaneous OSHA PEL. The mean representative workday asbestos air concentration from 1972 and 1975 was 1.09 f/cc. The mean representative workday concentration decreased to 0.13 f/cc between 1976 and 1985, then decreased again to 0.02 f/cc between 1986 and 1993 and 0.03 f/cc between 1994 and 2006. For task samples, the mean air concentration from 1972 to 1975 was 3.29 f/cc. The mean task sample concentration decreased to 0.48 f/cc between 1976 and 1985, then decreased again to 0.01 f/cc between 1986 and 1993 and 0.03 f/cc between 1994 and 2006. Only eleven out of the 495 samples (2.2%), for both task and representative workday samples, were in exceedance of the contemporaneous PEL(as an 8-hour TWA), ten of which occurred prior to 1978. Eight of these eleven PEL exceeding samples were task samples. Of the remaining three representative workday samples, two had unknown sampling times. IMPACT: This paper presents an analysis of all the available personal sampling data for airborne asbestos across 16 facilities of the U. S. Steel Corporation between 1972 and 2006. This dataset has previously never been publicly shared or analyzed. It represents one of the more complete industrial hygiene datasets from a corporation to be presented in a scientific journal and, due to the similarities in the processes at each mill, it should reflect analogous exposures throughout the steelmaking industry in the United States. One of the benefits of presenting these data is that it also provides insight into where asbestos-containing materials (ACMs) were used in the steel making process. This is just one example of a large firm that released information that had previously remained in file cabinets for decades. We believe that another benefit of publishing this paper is that it may encourage the largest firms in industry to assemble and analyze their industrial hygiene data to benefit the occupational hygiene, medical, and epidemiology communities. This can support future epidemiology studies and improve the design of future industrial hygiene programs.

RESUMEN

In Brazil, more than 90% of steel mills are located in states that have Atlantic Forest which, together with the pollution of large urban centers, represent risk factors for the environmental quality of this important biome. The aim of this study was to evaluate the effects of urban and industrial air pollution in a city in Minas Gerais that has a steel mill on the symptomatology, on the leaf chemistry, and on the anatomy and micromorphology of extrafloral nectaries (EFNs) of Joannesia princeps Vell. (Euphorbiaceae), a native species of the Atlantic Forest. For 126 days, seedlings of J. princeps were exposed on stand systems in the urban and industrial area of MG (Ipatinga city), in the following places: Bom Retiro, Cariru, Cidade Nobre, and Veneza. For anatomical analysis, EFNs were collected and processed for microscopic analysis. In the southern parts of the steel mill closest to the Rio Doce State Park (RDSP) (Bom Retiro and Cariru), there was a predominance of NO, NOX, SO2 (Bom Retiro), naphthalene, benzene, and total suspended particulates (Cariru). In locations north of the steel mill (Cidade Nobre and Veneza), there was a predominance of volatile organic compounds (VOCs). In the urban environment, intense anatomical and micromorphological damage to EFNs, leaf damage, leaf metal accumulation, and alterations in the histochemical tests of the plants were observed. The interior of the RDSP presented environmental quality, but the contribution of pollutants near the border between the RDSP and the city of Ipatinga is worrying, requiring constant monitoring of this area to verify the impact and threat that pollution can cause on these Atlantic Forest remnants.

Asunto(s)

RESUMEN

The global shortage of zinc mines makes the extraction of zinc from zinc-containing wastes a hot research topic. Most kinds of steel mill dust (SMD) cannot be directly returned to the ironmaking and steelmaking processes due to their zinc content. A large amount of SMD produced during steelmaking has become a major challenge for steel plants due to environmental pollution, health issues and land scarcity. Lots of processes for recovering metals from SMD have been developed to comprehensively utilize them and solve these environmental problems. Zinc in SMD can be recovered by these technologies, and the residue can be used as raw material for ironmaking. In this work, the sources and characteristics of SMD from different processes were analyzed firstly. Then, the mechanisms of physical, hydrometallurgical, pyrometallurgical and pyrometallurgy-hydrometallurgy combined processes for SMD disposal are presented, and these methods are compared in terms of energy consumption, process complexity and industrial application. Finally, suggestions and prospects for utilization of SMD are put forward.

RESUMEN

The objective is to present historical asbestos airborne concentrations associated with activities involving presumably asbestos-containing materials in steel mills. A total of 138 historical industrial hygiene air samples collected in three US steel mills from 1972 to 1982 were analyzed. The majority of samples were collected during relining of open hearth furnaces, stoves, and blast furnaces by steel mill bricklayers and bricklayer helpers. Over 75% of the samples (n = 106) were collected for 50 min or less, four samples were collected for 227 to 306 min, and sample durations were not reported for the remaining 28 samples. Average airborne fiber concentrations measured during relining activities of open hearth furnaces, stoves, and blast furnaces were 0.21 f/cc, 0.72 f/cc and 0.13 f/cc phase-contrast microscopy (PCM), respectively. Measured airborne fiber concentrations of four time-weighted average (TWA) samples (>227 min) averaged 0.045 f/cc. Estimated 8-h TWAs concentrations averaged 0.34 f/cc for bricklayers and 0.2 f/cc bricklayer helpers. While 8-h TWA concentration estimates for monitored tasks/jobs may often have exceeded current Occupational Safety and Health Administration (OSHA) Permissible Exposure Limits (PELs), they did not exceed relevant contemporaneous occupational exposure standards. This analysis provides a better understanding of historical airborne asbestos exposures that bricklayers and other tradesmen experienced during furnace and stove work in the US steel mills.

Asunto(s)

RESUMEN

The purpose of this study was to determine the heavy metal concentrations and ecological risks to farmland soils caused by atmospheric deposition adjoining five industrial steel districts in Tangshan, Hebei, China. A total of 39 topsoil samples from adjoining these plants were collected and analyzed for Pb, Zn, Cu, Cr, and As. The geo-accumulation index (Igeo) and potential ecological risk index (PERI) were calculated to assess the heavy metal pollution level in soils. The results showed that the levels of Pb and As in farmland soils adjoining all steel plants were more than the background value, with the As content being excessively high. The Cr and Cu contents of some samples were over the background values, but the Zn content was not. In all the research areas, the largest Igeo value of the heavy metals was for As, followed by Pb, and the largest monomial PERI ([Formula: see text]) was As, which showed that the pollution of As in farmland soils was significant and had considerable ecological risk. Additionally, the heavy metal sequential extraction experiments showed that Pb and Cr, which exceeded the background value, were present in about 20% of the exchangeable and carbonate-bound fractions in the soils surrounding some steel plants. This would imply the risk of these heavy metals being absorbed and accumulated by the crops. Therefore, the local government needs to control the pollution of heavy metals in the farmland soils adjoining the steel plant as soon as possible, in order to avoid possible ecological and food safety risks.

Asunto(s)

RESUMEN

Acetogens have often been observed to be inhibited by CO above an inhibition threshold concentration. In this study, a two-stage culture consisting of carboxydotrophic archaea and homoacetogenic bacteria is found to be effective in converting industrial waste gas derived from a steel mill process. In the first stage, Thermococcus onnurineus could grow on the Linz-Donawitz converter gas (LDG) containing ca. 56% CO as a sole energy source, converting the CO into H2 and CO2. Then, in the second stage, Thermoanaerobacter kivui could grow on the off-gas from the first stage culture, consuming the H2 and CO in the off-gas completely and producing acetate as a main product. T. kivui alone could not grow on the LDG gas. This work represents the first demonstration of acetate production using steel mill waste gas by a two-stage culture of carboxydotrophic hydrogenogenic microbes and homoacetogenic bacteria.

Asunto(s)

RESUMEN

The use of bioassay batteries is necessary to evaluate toxic effects at various biological levels. The selection of bioassays without prior testing and determination of the most sensitive/suitable groups for each impact may allow the discharge of effluents that pose a threat to the environment. The present study tested and selected a battery of sensitive ecotoxicological bioassays for detecting toxic effects of metals. The sensitivities of six organisms were evaluated (algae Pseudokirchneriella subcapitata and Chlorella vulgaris, Cladocera Daphnia similis and Ceriodaphnia dubia, and fish Poecilia reticulata and Danio rerio) after exposure to 10 individual metal species deemed toxic to the aquatic environment (Ag+, Cd2+, Cu+, Cu2+, Cr3+, Cr6+, Pb2+, Ni2+, Zn2+, and Hg2+) and to real (steel-mill) and laboratory simulated effluents. In the bioassays, fish were the least sensitive; D. rerio showed no sensitivity to any of the effluents tested. P. subcapitata was a good bioindicator of Cr3+ toxicity, and D. similis was the most sensitive organism to Hg2+; but the toxic effect of effluents with higher levels of Hg2+ was better detected by C. dubia. The most sensitive battery of bioassays to detect low concentrations of dissolved metals in effluents was the 72-h chronic test with C. vulgaris and the 48-h acute test with C. dubia.

RESUMEN

Steel-mill waste rolling oil (SmWRO) is considered as hazardous substance with high treatment and disposal fees. Anaerobic process could not only transform the hazardous substance into activated sludge, but also generate valuable biogas. This study aimed at studying the biochemical methane potential of SmWRO under inoculum to substrate VS ratios (ISRs) of 0.25, 0.5, 1, 1.5, 2 and 3 using septic tank sludge as inoculum in mesophilic and thermophilic conditions, with blank tests for control. Specific biogas yield (mL/g VS(added)), net biogas yield (mL/g VS(removed)) and VS removal were analyzed. The ANOVA results indicated great influence of ISR and temperature on studied parameters. ISR of 1.5 at 55°C and ISR of 1.5 and 2 at 35°C were suggested with the highest specific biogas yield (262-265 and 303mL/g VS(added)). Kinetic analysis showed that Gompertz model fit the experimental data best with the least RMSE and largest R(2).

Asunto(s)

RESUMEN

OBJECTIVES: This study was performed to estimate the prevalence and possible risk factors of the metabolic syndrome in steel-mill workers, and to evaluate the relation between gamma-glutamyltransferase (gamma-GTP) and the metabolic syndrome. METHODS: The study subjects comprised 1,604 male steel-mill workers. The indices of metabolic syndrome, such as BMI, triglyceride, HDL-cholesterol, blood pressure, fasting glucose, and gamma-GTP were analyzed in each subject. We collected information about demographic characteristics, behavioral patterns, such as alcohol drinking, smoking, and exercise, and family medical history through a self-administered questionnaire. Statistical analysis was done by using the chi-square test, Mantel-Haenszel trend test and logistic regression model. RESULTS: The crude and age-adjusted prevalences of the metabolic syndrome were 21.3% and 15.5%, respectively, in the steel-mill workers. Age (OR: 1.063, 95% CI: 1.033-1.094), alcohol drinking (OR: 1.657, 95% CI: 1.175-2.337) and smoking (OR: 1.359, 95% CI: 1.017-1.816) were risk factors for the metabolic syndrome. Meanwhile, shift work showed a significant relation with hypertension (OR: 1.329, 95% CI: 1.038-1.700), but not with other metabolic syndrome components. However, tenure, exercise and family medical history were not significant factors for the metabolic syndrome in this study. The risk ratio of the metabolic syndrome (OR: 3.345, 95 % CI: 2.534-4.416) and its components, such as obesity, hypertriglyceridemia, hypertension and hyperglycemia, were higher in the high gamma-GTP group (> or =63 IU/ liter) than in the controls (<63 IU/liter). CONCLUSIONS: These results confirm the need for health education to control the metabolic syndrome by improving behavioral patterns, such as alcohol drinking and smoking, in factory workers. In addition, it is suggested that gamma-GTP might be a useful candidate in screening for the metabolic syndrome.

Asunto(s)

RESUMEN

A cross-sectional study was conducted to investigate the effect of long term noise exposure on blood pressure among steel mill workers. The workers participated in periodic medical examinations performed from August 27 to September 6 in 1990. Examined were 1,034 workers with high-level noise exposure(average 91.8+/-5.2 dB{AA)), and 390 workers with low-level noise exposure(average 75.2+/-4.6 dB(A)). No significant difference was found in systolic or diastolic blood pressure between the two exposure groups. Prevalence of hypertension (> or = 160 mmHg systolic or > or = 100 mmHg diastolic) was higher in a younger age group ( or = 25dB at 1000 Hz or > or = 40 dB at 4000 Hz in at least one ear) than in the normal hearing group. From multiple regression analysis, hearing loss, body mass index, age, alcohol and family history of hypertension were proven to be predictors of diastolic blood pressure (p<0.02). When regression was performed for each age group, hearing loss was a strong predictor of diastolic pressure in the younger age group (p<0.01).

Asunto(s)