RESUMEN

High dielectric constant (k) materials have been investigated to improve the performance of dynamic random access memory (DRAM) capacitors. However, the conventional binary oxides have reached their fundamental limit of k < 100. In this study, we investigated alternative ternary oxides, SrTiO3 (STO) and (Ba,Sr)TiO3 (BSTO), which were epitaxially grown on SrRuO3 (SRO) using atomic layer deposition (ALD). The structural compatibility between SRO and STO enables the in situ crystallization of STO during ALD at a low temperature of 300 °C. Consequently, STO on SRO exhibited no film deformation, a common issue during high temperature postdeposition annealing, and maintained superior crystallinity at a thin thickness down to 50 Å. Furthermore, the dielectric constant of STO can be adjusted by modulating its tunable ferroelectric and dielectric properties through Ba doping. BSTO, with a high dielectric constant (kmax:527) achieved at a Ba doping concentration of approximately 50%, displayed a low leakage current density (3.9 × 10-8 A cm-2 @ 1 V) and demonstrated excellent reliability of 1012 cycles in the metal-insulator-metal capacitors. This study proposes a promising alternative to satisfy the extreme EOT required for next-generation DRAM capacitors.

RESUMEN

An electrochemical nitrite sensor probe is introduced herein using a modified flat glassy carbon electrode (GCE) and SrTiO3 material doped with spherical-shaped gold nanoparticles (Au-NPs) and polypyrrole carbon (PPyC) at a pH of 7.0 in a phosphate buffer solution. The nanocomposites (NCs) containing Au-NPs, PPyC, and SrTiO3 were synthesized by ultrasonication, and their properties were thoroughly characterized through structural, elemental, optical, and morphological analyses with various conventional spectroscopic methods, such as field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, high-resolution transmission electron microscopy, powder X-ray diffraction, X-ray photoelectron spectroscopy, and Brunauer-Emmett-Teller method. The peak currents due to nitrite oxidation were characterized in detail and analyzed using conventional cyclic voltammetry (CV) as well as differential pulse voltammetry (DPV) under ambient conditions. The sensor response increased significantly from 0.15 to 1.5 mM of nitrite ions, and the sensor was fabricated by coating a conducting agent (PEDOT:PSS) on the GCE to obtain the Au-NPs/PPyC/SrTiO3 NCs/PEDOT:PSS/GCE probe. The sensor's sensitivity was determined as 0.5 µA/µM∙cm2 from the ratio of the slope of the linear detection range by considering the active surface area (0.0316 cm2) of the flat GCE. In addition, the limit of detection was determined as 20.00 ± 1.00 µM, which was found to be satisfactory. The sensor's stability, pH optimization, and reliability were also evaluated in these analyses. Overall, the sensor results were found to be satisfactory. Real environmental samples were then analyzed to evaluate the sensor's reliability through DPV, and the results showed that the proposed novel electrochemical sensor holds great promise for mitigating water contamination in the real samples with the lab-made Au-NPs/PPyC/SrTiO3 NC. Thus, this study provides valuable insights for improving sensors for broad environmental monitoring applications using the electrochemical approach.

RESUMEN

The catalysts with three-dimensional porous (3DP) CeO2, LaFeO3 and SrTiO3 are synthesized by sol-gel method and chemical precipitation method. The resulting multi-component 3DP CeO2/LaFeO3/SrTiO3 composite material featured a high specific surface area (26.08 m2/g), which can provide more surface active sites to improve adsorption capacity and catalytic performance. The photocatalytic, Fenton-like, photo-Fenton-like performance of the catalyst are studied on decolorization of RhB under UV irradiation, respectively. 3DP CeO2/LaFeO3/SrTiO3 exhibits high catalytic performance. Compared with photocatalytic or Fenton-like performance, 3DP CeO2/LaFeO3/SrTiO3 catalyst exhibits higher photo-Fenton-like performance, facilitating efficient decolorization of the rhodamine B. Moreover, the initial reaction rate on decolorization of RhB with 3DP CeO2/LaFeO3/SrTiO3 is 10.55, 5.52, 3.67 and 1.51 times higher than that with SrTiO3, LaFeO3, 3DP CeO2 and 3DP CeO2/LaFeO3, respectively. Meanwhile, 3DP LaFeO3/CeO2/SrTiO3 has a wider pH usage range in the synergistic reaction. Finally, a catalytic mechanism for the decolorization of rhodamine B is proposed. The continuous cycling of Fe3+/Fe2+ and Ce4+/Ce3+ and the production of active substances are achieved under the photo-Fenton-like effect of the catalyst.

RESUMEN

The remarkable stability, suitable thermomechanical characteristics, and acceptable electrical properties of donor-doped strontium titanates make them attractive materials for fuel electrodes, interconnects, and supports of solid oxide fuel and electrolysis cells (SOFC/SOEC). The present study addresses the impact of processing and thermochemical treatment conditions on the electrical conductivity of SrTiO3-derived ceramics with moderate acceptor-type substitution in a strontium sublattice. A-site-deficient Sr0.85La0.10TiO3-δ and cation-stoichiometric Sr0.85Pr0.15TiO3+δ ceramics with varying microstructures and levels of reduction have been prepared and characterized by XRD, SEM, TGA, and electrical conductivity measurements under reducing conditions. The analysis of the collected data suggested that the reduction process of dense donor-doped SrTiO3 ceramics is limited by sluggish oxygen diffusion in the crystal lattice even at temperatures as high as 1300 °C. A higher degree of reduction and higher electrical conductivity can be obtained for porous structures under similar thermochemical treatment conditions. Metallic-like conductivity in dense reduced Sr0.85La0.10TiO3-δ corresponds to the state quenched from the processing temperature and is proportional to the concentration of Ti3+ in the lattice. Due to poor oxygen diffusivity in the bulk, dense Sr0.85La0.10TiO3-δ ceramics remain redox inactive and maintain a high level of conductivity under reducing conditions at temperatures below 1000 °C. While the behavior and properties of dense reduced Sr0.85Pr0.15TiO3+δ ceramics with a large grain size (10-40 µm) were found to be similar, decreasing grain size down to 1-3 µm results in an increasing role of resistive grain boundaries which, regardless of the degree of reduction, determine the semiconducting behavior and lower total electrical conductivity of fine-grained Sr0.85Pr0.15TiO3+δ ceramics. Oxidized porous Sr0.85Pr0.15TiO3+δ ceramics exhibit faster kinetics of reduction compared to the Sr0.85La0.10TiO3-δ counterpart at temperatures below 1000 °C, whereas equilibration kinetics of porous Sr0.85La0.10TiO3-δ structures can be facilitated by reductive pre-treatments at elevated temperatures.

RESUMEN

Devising of materials that afforded dual applicability in decontamination and pollutant detection were still a towering challenge owing to the increasing flux of discharge toxic contaminants over the years. Herein, the NiFe2O4 nanoparticles-loaded on cube-like SrTiO3 (NiFe2O4/SrTiO3) composite was fabricated by a two-step hydrothermal approach providing remarkable photocatalytic treatment and electrochemical sensing of noxious pollutants in wastewater. The material traits of the fabricated composite were scrutinized by myriad characterization approaches. The NiFe2O4/SrTiO3 hybrid material demonstrated high surface area of 19.81 m2/g, adequate band gap energy of 2.75 eV, and prominent photoluminescence characteristics. In the presence of visible light, the NiFe2O4/SrTiO3 exhibited profound photocatalysis capability to eliminate sewage effluent-bearing chlortetracycline hydrochloride (CTCH) with 88.6% COD removal in 120 min, outperforming other pure materials. Meanwhile, the toxicity examination of effluent, the possible degradation pathway of CTCH and the proposed photocatalysis mechanism were also divulged. More importantly, the glassy carbon electrode was modified with synergized NiFe2O4/SrTiO3 (NiFe2O4/SrTiO3-GCE) was adopted for the precise quantification of Hydrazine (Hz). The NiFe2O4/SrTiO3-GCE obeyed first-order response for the Hz detection within the range of 1-10 mM: cyclic voltametric: limit of detection (LOD) of 0.119 µM with sensitivity of 18.9 µA µM-1 cm-2, and linear sweep voltametric: LOD of 0.222 µM with a sensitivity of 12.05 µA µM-1 cm-2. The stability and interference of modified electrode were also inspected. This work furnished valuable insights to yield a composite with the prominent S-scheme heterojunction system for quenching of charge carrier recombination and consequently contributing to the future realization into the domains of environmental clean-up and toxic chemical detection.

Asunto(s)

Técnicas Electroquímicas , Compuestos Férricos , Hidrazinas , Níquel , Óxidos , Aguas del Alcantarillado , Estroncio , Titanio , Contaminantes Químicos del Agua , Hidrazinas/química , Hidrazinas/análisis , Titanio/química , Estroncio/química , Estroncio/análisis , Contaminantes Químicos del Agua/análisis , Contaminantes Químicos del Agua/química , Óxidos/química , Níquel/análisis , Níquel/química , Compuestos Férricos/química , Aguas del Alcantarillado/química , Técnicas Electroquímicas/métodos , Eliminación de Residuos Líquidos/métodos , Catálisis , Procesos Fotoquímicos , Aguas Residuales/química , Aguas Residuales/análisis

RESUMEN

One way to effectively address endophyte infection and loosening is the creation of multifunctional coatings that combine anti-inflammatory, antibacterial, and vascularized osteogenesis. This study started with the preparation of strontium-doped titanium dioxide nanotubes (STN) on the titanium surface. Next, tannic acid (TA), gentamicin sulfate (GS), and pluronic F127 (PF127) were successfully loaded into the STN via layer-by-layer self-assembly, resulting in the STN@TA-GS/PF composite coatings. The findings demonstrated the excellent hydrophilicity and bioactivity of the STN@TA-GS/PF coating. STN@TA-GS/PF inhibited E. coli and S. aureus in vitro to a degree of roughly 80.95 % and 92.45 %, respectively. Cellular investigations revealed that on the STN@TA-GS/PF surface, the immune-system-related RAW264.7, the vasculogenic HUVEC, and the osteogenic MC3T3-E1 showed good adhesion and proliferation activities. STN@TA-GS/PF may influence RAW264.7 polarization toward the M2-type and encourage MC3T3-E1 differentiation toward osteogenesis at the molecular level. Meanwhile, the STN@TA-GS/PF coating achieved effective removal of ROS within HUVEC and significantly promoted angiogenesis. In both infected and non-infected bone defect models, the STN@TA-GS/PF material demonstrated strong anti-inflammatory, antibacterial, and vascularization-promoting osteogenesis properties. In addition, STN@TA-GS/PF had good hemocompatibility and biosafety. The three-step process used in this study to modify the titanium surface for several purposes gave rise to a novel concept for the clinical design of antimicrobial coatings with immunomodulatory properties.

Asunto(s)

Antibacterianos , Antiinflamatorios , Materiales Biocompatibles Revestidos , Escherichia coli , Nanotubos , Prótesis e Implantes , Staphylococcus aureus , Estroncio , Titanio , Titanio/química , Titanio/farmacología , Nanotubos/química , Ratones , Animales , Estroncio/química , Estroncio/farmacología , Antiinflamatorios/farmacología , Antiinflamatorios/química , Staphylococcus aureus/efectos de los fármacos , Humanos , Materiales Biocompatibles Revestidos/química , Materiales Biocompatibles Revestidos/farmacología , Escherichia coli/efectos de los fármacos , Antibacterianos/farmacología , Antibacterianos/química , Células RAW 264.7 , Células Endoteliales de la Vena Umbilical Humana/efectos de los fármacos , Pruebas de Sensibilidad Microbiana , Propiedades de Superficie , Taninos/química , Taninos/farmacología , Osteogénesis/efectos de los fármacos , Poloxámero/química , Poloxámero/farmacología , Proliferación Celular/efectos de los fármacos , Gentamicinas/farmacología , Gentamicinas/química , Tamaño de la Partícula

RESUMEN

The adsorption properties of CO2 on the SrTiO3(001) surface were investigated using ambient pressure X-ray photoelectron spectroscopy under elevated pressure and temperature conditions. On the Nb-doped TiO2-enriched (1 × 1) SrTiO3 surface, CO2 adsorption, i.e., the formation of CO3 surface species, occurs first at the oxygen lattice site under 10-6 mbar CO2 at room temperature. The interaction of CO2 molecules with oxygen vacancies begins when the CO2 pressure increases to 0.25 mbar. The adsorbed CO3 species on the Nb-doped SrTiO3 surface increases continuously as the pressure increases but starts to leave the surface as the surface temperature increases, which occurs at approximately 373 K on the defect-free surface. On the undoped TiO2-enriched (1 × 1) SrTiO3 surface, CO2 adsorption also occurs first at the lattice oxygen sites. Both the doped and undoped SrTiO3 surfaces exhibit an enhancement of the CO3 species with the presence of oxygen vacancies, thus indicating the important role of oxygen vacancies in CO2 dissociation. When OH species are removed from the undoped SrTiO3 surface, the CO3 species begin to form under 10-6 mbar at 573 K, thus indicating the critical role of OH in preventing CO2 adsorption. The observed CO2 adsorption properties of the various SrTiO3 surfaces provide valuable information for designing SrTiO3-based CO2 catalysts.

RESUMEN

The development of an efficient, selective, and durable catalysis system for the electrocatalytic N2 reduction reaction (ENRR) is a promising strategy for the sustainable production of ammonia. The high-performance ENRR is limited by two major challenges: poor adsorption of N2 over the catalyst surface and abysmal N2 solubility in aqueous electrolytes. Herein, with the help of our combined density functional theory (DFT) calculations and experimental electrocatalysis study, we demonstrate that concurrently induced electron-deficient Lewis acid sites in an electrocatalyst and in an electrolyte medium can significantly boost the ENRR performance. The DFT calculations, ex situ X-ray photoelectron and FTIR spectroscopy, electrochemical measurements, and N2-TPD (temperature-programmed desorption) over boron-doped strontium titanate (BSTO) samples reveal that the Lewis acid-base interactions of N2 synergistically enhance the adsorption and activation of N2. Besides, the B-dopant induces the defect sites (oxygen vacancies and Ti3+) that assist in enhanced N2 adsorption and results in suppressed hydrogen evolution due to B-induced electron-deficient sites for H+ adsorption. The insights from the DFT study evince that B prefers the Srtop position (on top of Sr) where N2 adsorbs in an end-on configuration, which favors the associative alternating pathway and suppresses the competitive hydrogen evolution. Thus, our combined experimental and DFT study demonstrates an insight toward enhancing the ENRR performance along with the suppressed hydrogen evolution via concurrently engineered electron-deficient sites at electrode and electrolyte interfaces.

RESUMEN

We present a numerical investigation of self-diffusion on strontium titanate TiO2-terminated (001) surfaces via density functional theory. Our calculations first indicate that Ti has the highest diffusion barrier with approximately 2.20 eV, thus representing the rate-limiting step for surface self-diffusion. Furthermore, the higher energy barriers of O and Ti in comparison to O2and TiO2indicate electronic activity with the surface atoms. Under the consideration of equi-biaxial strain as it would be encountered in e.g. heteroepitaxial thin films, the diffusion barriers for surface self-diffusion decrease for both compressive and tensile strains between -6% and 2%. For larger strains, we observe plastic deformations. This possibility to lower the energy barrier paves the way for accelerated and possible new mechanisms of surface diffusion and reconstruction of strontium titanate structures in a wide range of applications.

RESUMEN

A metal-free combination of rGO/g-C3N4-coupled SrTiO3 (SRN) ternary nanocomposite prepared via a wet impregnation method for UV-Vis light photocatalytic applications. Various physicochemical properties of the samples were investigated by several spectroscopic techniques including X-ray diffraction (XRD), FT-IR, Raman, field emission scanning electron microscopy with energy dispersive X-ray spectroscopy (FE-SEM-EDX), high-resolution transmission electron microscopy (HR-TEM), UV-Vis, photoluminescence (PL), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) surface area analysis. The data suggest agglomerated SRT nanoparticles are dispersed and distributed throughout the surface of the rGO sheets and GCN nanostructures. The photocatalytic performance of the SRN towards combined mixed dye and its degradation activities were evaluated towards the most common industrial effluents, Rhodamine B (RhB) and Methylene blue (MB), under UV-Vis light illumination. The results revealed that the degradation efficiency of the SRN photocatalyst shows excellent performance compared with that of the binary composition and the pure SrTiO3 (SRT) sample. The reaction rate constant for RhB was estimated to be 0.0039 min-1 and for MB to be 0.0316 min-1, which are 3.26 (RhB) and 4.21 (MB) times faster than the pure SRT sample. The enhanced degradation efficiency was attained not only by interfacial formation but also by the speedy transportation of electrons across the heterojunction. After 5 runs of the photocatalytic recylic process, the SRN photocatalyst exhibited ultimate stability without structural changes, and no noticeable degradation was observed. The outcomes of the ternary SRN nanocomposite manifest a dual photocatalytic scheme, the photocatalytic enrichment could be caused by the Z-scheme charge transfer process between GCN, SRT, and rGO nanocomposite, which helps effectual charge separation and keeps a high redox potential. From the results, SRN sample provides insight into the integration of an effective and potential photocatalyst for wastewater treatment toward real-time environmental remediation applications.

RESUMEN

Semihydrogenation is a crucial industrial process. Noble metals such as Pd have been extensively studied in semihydrogenation reactions, owing to their unique catalytic activity toward hydrogen activation. However, the overhydrogenation of alkenes to alkanes often happens due to the rather strong adsorption of alkenes on Pd active phases. Herein, we demonstrate that the incorporation of Pd active phases as single-atom sites in perovskite lattices such as SrTiO3 can greatly alternate the electronic structure and coordination environment of Pd active phases to facilitate the desorption of alkenes rather than further hydrogenation. Furthermore, the incorporated Pd sites can be well stabilized without sintering by a strong host-guest interaction with SrTiO3 during the activation of H species in hydrogenation reactions. As a result, the Pd incorporated SrTiO3 (Pd-SrTiO3) exhibits an excellent time-independent selectivity (> 99.9 %) and robust durability for the photocatalytic semihydrogenation of phenylacetylene to styrene. This strategy based on incorporation of active phases in perovskite lattices will have broad implications in the development of high-performance photocatalysts for selective hydrogenation reactions.

RESUMEN

The discovery of high-mobility two-dimensional electron gas and low carrier density superconductivity in multiple SrTiO3-based heterostructures has stimulated intense interest in the surface properties of SrTiO3. The recent discovery of high-Tc superconductivity in the monolayer FeSe/SrTiO3 led to the upsurge and underscored the atomic precision probe of the surface structure. By performing atomically resolved cryogenic scanning tunneling microscopy/spectroscopy characterization on dual-TiO2-δ-terminated SrTiO3(001) surfaces with (√13 × âˆš13), c(4 × 2), mixed (2 × 1), and (2 × 2) reconstructions, we disclosed universally broken rotational symmetry and contrasting bias- and temperature-dependent electronic states for apical and equatorial oxygen sites. With the sequentially evolved surface reconstructions and simultaneously increasing equatorial oxygen vacancies, the surface anisotropy reduces and the work function lowers. Intriguingly, unidirectional stripe orders appear on the c(4 × 2) surface, whereas local (4 × 4) order emerges and eventually forms long-range unidirectional c(4 × 4) charge order on the (2 × 2) surface. This work reveals robust unidirectional charge orders induced by oxygen vacancies due to strong and delicate electronic-lattice interaction under broken rotational symmetry, providing insights into understanding the complex behaviors in perovskite oxide-based heterostructures.

RESUMEN

The interfacial FeSe/TiO2-δ coupling induces high-temperature superconductivity in monolayer FeSe films. Using cryogenic atomically resolved scanning tunneling microscopy/spectroscopy, we obtained atomic-site dependent surface density of states, work function, and the pairing gap in the monolayer FeSe on the SrTiO3(001)-(√13 × âˆš13)-R33.7° surface. Our results disclosed the out-of-plane Se-Fe-Se triple layer gradient variation, switched DOS for Fe sites on and off TiO5□, and inequivalent Fe sublattices, which gives global spatial modulation of pairing gap contaminants with the (√13 × âˆš13) pattern. Moreover, the coherent lattice coupling induces strong inversion asymmetry and in-plane anisotropy in the monolayer FeSe, which is demonstrated to correlate with the particle-hole asymmetry in coherence peaks. These results disclose delicate atomic-scale correlations between pairing and lattice-electronic coupling in the Bardeen-Cooper-Schrieffer to Bose-Einstein condensation crossover regime, providing insights into understanding the pairing mechanism of multiorbital superconductivity.

RESUMEN

Infection and aseptic loosening caused by bacteria and poor osseointegration remain serious challenges for orthopedic implants. The advanced surface modification of implants is an effective strategy for addressing these challenges. This study presents a "pneumatic nanocannon" coating for titanium orthopedic implants to achieve on-demand release of antibacterial and sustained release of osteogenic agents. SrTiO3 nanotubes (SrNT) were constructed on the surface of Ti implants as "cannon barrel," the "cannonball" (antibiotic) and "propellant" (NH4HCO3) were codeposited into SrNT with assistance of mussel-inspired copolymerization of dopamine and subsequently sealed by a layer of polydopamine. The encapsulated NH4HCO3 within the nanotubes could be thermally decomposed into gases under near-infrared irradiation, propelling the on-demand delivery of antibiotics. This coating demonstrated significant efficacy in eliminating typical pathogenic bacteria both in planktonic and biofilm forms. Additionally, this coating exhibited a continuous release of strontium ions, which significantly enhanced the osteogenic differentiation of preosteoblasts. In an implant-associated infection rat model, this coating demonstrated substantial antibacterial efficiency (>99%) and significant promotion of osseointegration, along with alleviated postoperative inflammation. This pneumatic nanocannon coating presents a promising approach to achieving on-demand infection inhibition and sustained osseointegration enhancement for titanium orthopedic implants.

Asunto(s)

Antibacterianos , Nanotubos , Óxidos , Estroncio , Titanio , Estroncio/química , Estroncio/farmacología , Animales , Titanio/química , Titanio/farmacología , Antibacterianos/farmacología , Antibacterianos/química , Ratas , Óxidos/química , Óxidos/farmacología , Nanotubos/química , Prótesis e Implantes , Oseointegración/efectos de los fármacos , Ratones , Ratas Sprague-Dawley , Indoles/química , Indoles/farmacología , Materiales Biocompatibles Revestidos/química , Materiales Biocompatibles Revestidos/farmacología , Osteogénesis/efectos de los fármacos , Propiedades de Superficie , Polímeros/química , Polímeros/farmacología , Biopelículas/efectos de los fármacos , Pruebas de Sensibilidad Microbiana

RESUMEN

Ni-rich layered ternary cathodes are promising candidates thanks to their low toxic Co-content and high energy density (∼800 Wh/kg). However, a critical challenge in developing Ni-rich cathodes is to improve cyclic stability, especially under high voltage (>4.3 V), which directly affects the performance and lifespan of the battery. In this study, niobium-doped strontium titanate (Nb-STO) is successfully synthesized via a facile solvothermal method and used as a surface modification layer onto the LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode. The results exhibited that the Nb-STO modification significantly improved the cycling stability of the cathode material even under high-voltage (4.5 V) operational conditions. In particular, the best sample in our work could provide a high discharge capacity of ∼190 mAh/g after 100 cycles under 1 C with capacity retention over 84% in the voltage range of 3.0-4.5 V, superior to the pristine NCM811 (∼61%) and pure STO modified STO-811-600 (∼76%) samples under the same conditions. The improved electrochemical performance and stability of NCM811 under high voltage should be attributed to not only preventing the dissolution of the transition metals, further reducing the electrolyte's degradation by the end of charge, but also alleviating the internal resistance growth from uncontrollable cathode-electrolyte interface (CEI) evolution. These findings suggest that the as-synthesized STO with an optimized Nb-doping ratio could be a promising candidate for stabilizing Ni-rich cathode materials to facilitate the widespread commercialization of Ni-rich cathodes in modern LIBs.

RESUMEN

Successful preparation of PVA/SrTiO3/CNT polymer nanocomposite films was accomplished via the solution casting method. The structural, optical, and thermal properties of the films were tested by XRD, SEM, FTIR, TGA, and UV-visible spectroscopy. Inclusion of the SrTiO3/CNT nanofillers with a maximum of 1 wt% drastically improved the optical and thermal properties of PVA films. SrTiO3 has a cubic crystal structure, and its average crystal size was found to be 28.75 nm. SEM images showed uniform distribution in the sample with 0.3 wt% of SrTiO3/CNTs in the PVA film, while some agglomerations appeared in the samples of higher SrTiO3/CNT content, i.e., at 0.7 and 1.0 wt%, in the PVA polymer films. The inclusion of SrTiO3/CNTs improved the thermal stability of PVA polymer films. The direct and indirect optical band gaps of the PVA films decreased when increasing the mass of the SrTiO3/CNTs, while the single-oscillator energy (E0) and dispersion energy (Ed) increased. The films' refractive indices were gradually increased upon increasing the nanofillers' weight. In addition, improvements in the optical susceptibility and nonlinear refractive indices' values were also obtained. These films are qualified for optoelectronic applications due to their distinct optical and thermal properties.

RESUMEN

The fabrication of solid solutions represents a compelling approach to modulating the physicochemical properties of materials. In this study, we achieved the successful synthesis of solid solutions comprising SrTiO3 and SrTaO2N (denoted as (SrTiO3)1-x-(SrTaO2N)x, 0≤x≤1) using the magnesium powder-assisted nitridation method. The absorption edge of (SrTiO3)1-x-(SrTaO2N)x is tunable from 500 to 600 nm. The conduction band minimum (CBM) of (SrTiO3)1-x-(SrTaO2N)x comprises the Ti 3d orbitals and the Ta 5d orbitals, while the valence band maximum (VBM) consists of the O 2p and N 2p orbitals. The microstructure of the (SrTiO3)1-x-(SrTaO2N)x consists of small nanoparticles, exhibiting a larger specific surface area than the parent compounds of SrTiO3 and SrTaO2N. In the photocatalytic hydrogen evolution reaction (HER) with sacrificial reagents, the activity of solid solutions is notably superior to that of nitrogen-doped SrTiO3 and SrTaO2N. This superiority is mainly attributed to its broad light absorption range and high charge separation efficiency, which indicates its potential as a promising photocatalytic material. Moreover, the magnesium powder-assisted nitridation method exhibits obvious advantages for the synthesis of oxynitrides and bears instructional significance for the synthesis of other nitrogen-containing compounds and even sulfur-containing compounds.

RESUMEN

Atomic-resolution scanning transmission electron microscopy combined with 2D Gaussian fitting enables the accurate and precise identification of atomic column positions within a few picometers. The measurement performance significantly depends on the signal-to-noise ratio of the atomic columns. In areas with low signal-to-noise ratios, such as near surfaces, the measurement performance was lower than that of the bulk. However, previous studies evaluated the accuracy and precision only in bulk areas, underscoring the need for a method that quantitatively evaluates the accuracy and precision of each atomic column position with various signal-to-noise ratios. This study introduced Bayesian inference to assess the accuracy and precision of determining individual atomic column positions under various signals. We applied this method to simulated and experimental images and demonstrated its effectiveness in identifying statistically significant displacements, particularly near surfaces with signal degradation. The use of vector maps and kernel density estimate plots obtained from Bayesian inference provided a probabilistic understanding of the atom displacement. Therefore, this study highlighted the potential benefits of Bayesian inference in high-resolution imaging to reveal material properties.

RESUMEN

Suppressing carrier recombination in bulk and facilitating carrier transfer to surface via rational structure design is of great significance to improve solar-to-H2 conversion efficiency. We demonstrate a facile hydrothermal method to synthesize porous SrTiO3 single crystals (SrTiO3-P) with exposed (001) facets by introducing carbon spheres as templates. The obviously increased surface photovoltage and photocurrent response indicate that the interconnected pore walls act as enormous charge transfer "highways", accelerating carrier transport from bulk to surface. Furthermore, the absence of grain boundaries and high crystallinity could also lower the carrier recombination rate. Thus, the SrTiO3-P photocatalyst loaded with Rh/Cr2O3 as cocatalyst exhibits 1.5 times higher overall water splitting activity than that of solid SrTiO3, with gas evolution rate of 19.99 µmol h-1 50 mg-1 for H2 and 11.37 µmol h-1 50 mg-1 for O2. Additionally, SrTiO3-P also shows superior stability without any decay during cycling testing. This work provides a new insight into designing efficient multicomponent photocatalysts with a single-crystal porous structure.

RESUMEN

Artificial photosynthesis of fuels has garnered significant attention, with SrTiO3 emerging as a potential candidate for photocatalysis due to its exceptional physicochemical properties. However, selectively converting CO2 into fuels with desired reaction products remains a grand challenge. Herein, we design an updated method via an aging strategy based on the electrospinning technique to synthesize a single-crystalline Al-doped SrTiO3 nanotubular networks with self-assembled orderly mesopores, further modified by Cu-Pd alloy. It exhibits both high crystallinity and superior cross-linked mesoporous structures, effectively facilitating charge carrier transfer, photon utilization, and mass transfer, with a remarkable enhancement from 0.025 mmol h-1 m-2 to 1.090 mmol h-1 m-2 in the CO production rate. Meanwhile, the ordered arrangement of Cu and Pd atoms on the (111) surface can promote the rate-determining step (*CO2 to *COOH), which is also responsible for its good activity. The presence of CuO in the reaction confers a significant advantage for CO desorption, leading to a remarkable CO selectivity of 95.54 %. This work highlights new insights into developing advanced heterogeneous photocatalysts.