RESUMEN

Riboflavin overproduction byCorynebacterium glutamicumwas achieved by screening synthetic operons, enabling fine-tuned expression of the riboflavin biosynthetic genesribGCAH.The synthetic operons were designed by means of predicted translational initiation rates of each open reading frame, with the best-performing selection enabling riboflavin overproduction without negatively affecting cell growth. Overexpression of the fructose-1,6-bisphosphatase (fbp) and 5-phosphoribosyl 1-pyrophosphate aminotransferase (purF) encoding genes was then done to redirect the metabolic flux towards the riboflavin precursors. The resulting strain produced 8.3 g l-1of riboflavin in glucose-based fed-batch fermentations, which is the highest reported riboflavin titer withC. glutamicum. Further genetic engineering enabled both xylose and mannitol utilization byC. glutamicum, and we demonstrated riboflavin overproduction with the xylose-rich feedstocks rice husk hydrolysate and spent sulfite liquor, and the mannitol-rich feedstock brown seaweed hydrolysate. Remarkably, rice husk hydrolysate provided 30% higher riboflavin yields compared to glucose in the bioreactors.

Asunto(s)

RESUMEN

For a sustainable economy, biorefineries that use second-generation feedstocks to produce biochemicals and biofuels are essential. However, the exact composition of renewable feedstocks depends on the natural raw materials used and is therefore highly variable. In this contribution, a process analytical technique (PAT) strategy for determining the sugar composition of lignocellulosic process streams in real-time to enable better control of bioprocesses is presented. An in-line mid-IR probe was used to acquire spectra of ultra-filtered spent sulfite liquor (UF-SSL). Independent partial least squares models were developed for the most abundant sugars in the UF-SSL. Up to 5 sugars were quantified simultaneously to determine the sugar concentration and composition of the UF-SSL. The lowest root mean square errors of the predicted values obtained per analyte were 1.02 g/L arabinose, 1.25 g/L galactose, 0.50 g/L glucose, 1.60 g/L mannose, and 0.85 g/L xylose. Equipped with this novel PAT tool, new bioprocessing strategies can be developed for UF-SSL.

Asunto(s)

RESUMEN

Spent sulfite liquor (SSL) from softwood processing is rich in hemicellulose (acetyl galactoglucomannan, AcGGM), lignin, and lignin-derived compounds. We investigated the effect of sequential AcGGM purification on the enzymatic bioconversion of AcGGM. SSL was processed through three consecutive purification steps (membrane filtration, precipitation, and adsorption) to obtain AcGGM with increasing purity. Significant reduction (~99%) in lignin content and modest loss (~18%) of polysaccharides was observed during purification from the least pure preparation (UFR), obtained by membrane filtration, compared to the purest preparation (AD), obtained by adsorption. AcGGM (~14.5 kDa) was the major polysaccharide in the preparations; its enzymatic hydrolysis was assessed by reducing sugar and high-performance anion-exchange chromatography analysis. The hydrolysis of the UFR preparation with Viscozyme L or Trichoderma reesei ß-mannanase TrMan5A (1 mg/mL) resulted in less than ~50% bioconversion of AcGGM. The AcGGM in the AD preparation was hydrolyzed to a higher degree (~67% with TrMan5A and 80% with Viscozyme L) and showed the highest conversion rate. This indicates that SSL contains enzyme-inhibitory compounds (e.g., lignin and lignin-derived compounds such as lignosulfonates) which were successfully removed.

Asunto(s)

RESUMEN

BACKGROUND: Lignosulfonates are significant wood chemicals with a $700 million market, produced by sulfite pulping of wood. During the pulping process, spent sulfite liquor (SSL) is generated, which in addition to lignosulfonates contains hemicellulose-derived sugars-in case of hardwoods primarily the pentose sugar xylose. The pentoses are currently underutilized. If they could be converted into value-added chemicals, overall economic profitability of the process would increase. SSLs are typically very inhibitory to microorganisms, which presents a challenge for a biotechnological process. The aim of the present work was to develop a robust yeast strain able to convert xylose in SSL to carboxylic acids. RESULTS: The industrial strain Ethanol Red of the yeast Saccharomyces cerevisiae was engineered for efficient utilization of xylose in a Eucalyptus globulus lignosulfonate stream at low pH using CRISPR/Cas genome editing and adaptive laboratory evolution. The engineered strain grew in synthetic medium with xylose as sole carbon source with maximum specific growth rate (µmax) of 0.28 1/h. Selected evolved strains utilized all carbon sources in the SSL at pH 3.5 and grew with µmax between 0.05 and 0.1 1/h depending on a nitrogen source supplement. Putative genetic determinants of the increased tolerance to the SSL were revealed by whole genome sequencing of the evolved strains. In particular, four top-candidate genes (SNG1, FIT3, FZF1 and CBP3) were identified along with other gene candidates with predicted important roles, based on the type and distribution of the mutations across different strains and especially the best performing ones. The developed strains were further engineered for production of dicarboxylic acids (succinic and malic acid) via overexpression of the reductive branch of the tricarboxylic acid cycle (TCA). The production strain produced 0.2 mol and 0.12 mol of malic acid and succinic acid, respectively, per mol of xylose present in the SSL. CONCLUSIONS: The combined metabolic engineering and adaptive evolution approach provided a robust SSL-tolerant industrial strain that converts fermentable carbon content of the SSL feedstock into malic and succinic acids at low pH.in production yields reaching 0.1 mol and 0.065 mol per mol of total consumed carbon sources.. Moreover, our work suggests potential genetic background of the tolerance to the SSL stream pointing out potential gene targets for improving the tolerance to inhibitory industrial feedstocks.

RESUMEN

In this study the use of a particle filter algorithm to monitor Corynebacterium glutamicum fed-batch bioprocesses with uncertain raw material input composition is shown. The designed monitoring system consists of a dynamic model describing biomass growth on spent sulfite liquor. Based on particle filtering, model simulations are aligned with continuously and noninvasively measured carbon evolution and oxygen uptake rates, giving an estimate of the most probable culture state. Applied on two validation experiments, culture states were accurately estimated during batch and fed-batch operations with root mean square errors below 1.1 g L-1 for biomass, 0.6 g L-1 for multiple substrate concentrations and 0.01 g g-1 h-1 for biomass specific substrate uptake rates. Additionally, upon fed-batch start uncertain feedstock concentrations were corrected by the estimator without the need of any additional measurements. This provides a solid basis towards a more robust operation of bioprocesses utilizing lignocellulosic side streams.

Asunto(s)

RESUMEN

In this work, three polymeric resins were examined as alternatives for the separation of hemicellulose and lignin. The aim was to remove the lignin from spent-sulfite-liquor (SSL) prior to ultrafiltration, producing a hemicellulose-rich retentate with high purity, and increase the capacity of the membrane filtration. The lignin in the SSL was sulfonated; thus, two of the resins were anion exchangers and 1 was hydrophobic. The data from the equilibrium studies and adsorption kinetics were fitted to established models, and the results were interpreted based on these observations. The strongly basic anion exchanger performed best with regard to lignin removal. The adsorption followed the Sips isotherm, indicating that the process was cooperative with chemisorption as the main reaction between the adsorbate and adsorbent based on the kinetics. Regeneration of the adsorbent was also possible, wherein 100 g/L NaCl was sufficient to recover 98% of the lignin. The lignin removal had a positive effect on the ultrafiltration process, in which the flux increased by 38% and the extent of separation between the hemicellulose and lignin rose from 17% to 59%.

Asunto(s)

RESUMEN

Spent sulfite liquor is an abundant but currently less used wastewater stream from the pulp and paper industry. The recovery of lignin from this resource would provide an inexpensive raw material for the manufacture of fuels and fine chemicals. Here we investigated the suitability of ceramic hollow-fiber membranes for the concentration of spent sulfite liquor as an alternative to common membrane technologies. We tested three ceramic hollow-fiber membranes (3, 8, and 30 nm) in different membrane processes (fed-batch and total recycle mode) and compared their performance with the widely-used tubular membrane geometry. We also evaluated backflushing as a strategy to reduce membrane fouling during filtration. The juxtaposition of the two membrane geometries revealed that wall shear stress is the most important process parameter for the assessment of membrane performance according to permeate flux. The higher the wall shear stress, the higher the permeate flux. Due to the smaller inner diameter of the hollow-fiber membranes, higher wall shear stress can be achieved more easily. Backflushing had no effect on the permeate flux during the concentration experiments.

RESUMEN

Currently, the majority of binders used in wood particleboard (PB) manufacturing are formaldehyde-based synthetic resins. Because of the toxicity of formaldehyde, there is a strong demand for eco-friendly alternatives with similar performances and economic viability. In this work, thick spent sulfite liquor (TSSL), an industrial byproduct from sulfite pulp mills, is proposed as a binder for fully bio-based PBs. The results showed that PBs bound with TSSL present appropriate mechanical performance, which was further improved when TSSL was combined with wheat flour at an 84:16 dry weight ratio and preheated to 94 °C prior to application. For 13.2% binder content per dry wood weight, the PB internal bond strength was 0.46 N mm-2, which is above the standard requirements for PB type P2 (0.35 N mm-2). Optical microscopy showed that TSSL hinders the gelatinization of starch granules during preheating, allowing the binder mixture to maintain a low viscosity suitable for combination with wood particles and PB production.

RESUMEN

Mixed microbial cultures (MMC) and waste/surplus substrates, as hardwood spent sulfite liquor, are being used to decrease polyhydroxyalkanoates' (PHA) production costs. The process involves two or three steps, being the selection step a crucial one. For the industrial implementation of this strategy, reactor stability in terms of both performance and microbial community presence has to be considered. A long-term operation of a sequencing batch reactor under feast/famine conditions was performed along with microbial community identification/quantification using FISH and DGGE. The community was found to be extremely dynamic, dominated by Alphaproteobacteria, with Paracoccus and Rhodobacter present, both PHA-storing microorganisms. 16S rRNA gene clone library further revealed that side populations' non-PHA accumulators were able to strive (Agrobacterium, Flavobacteria, and Brachymonas). Nevertheless, reactor performance in terms of PHA storage was stable during operation time. The monitoring of the MMC population evolution provided information on the relation between community structure and process operation.

Asunto(s)

RESUMEN

Utilization of renewable resources is becoming increasingly important, and only sustainable processes that convert such resources into useful products can achieve environmentally beneficial economic growth. Wastewater from the pulp and paper industry is an unutilized resource offering the potential to recover valuable products such as lignin, pigments, and water [1]. The recovery of lignin is particularly important because it has many applications, and membrane technology has been investigated as the basis of innovative recovery solutions. The concentration of lignin can be increased from 62 to 285 g∙L(-1) using membranes and the recovered lignin is extremely pure. Membrane technology is also scalable and adaptable to different waste liquors from the pulp and paper industry.

RESUMEN

Lignosulfonates are abundantly available byproducts of the paper and pulping industry, and they therefore represent a promising feedstock for new sustainable processes. For industrial applications of lignosulfonates, their molecular weight distribution is a critical factor. In order to decrease the average molecular weight of lignosulfonates, Seventeen basidiomycetes were screened for their capability to depolymerize lignosulfonates from spent sulfite liquor (SSL) in surface and liquid cultures. Five basidiomycetes polymerized the lignosulfonates under the selected conditions. Only Irpex consors was found to efficiently degrade calcium lignosulfonates when SSL (0.5%, w/w) was used as the sole carbon and nitrogen source. The average molecular weight of the lignosulfonates was reduced from ∼26 to ∼4 kDa as determined by size exclusion chromatography (SEC) within two weeks. Various extracellular enzyme activities of I. consors were determined over the culture period. High peroxidase activities were correlating with a high degradation rate and the culture was harvested at the day of highest peroxidase activity. A putative versatile peroxidase was isolated by fast protein liquid chromatography (FPLC) and its encoding cDNA was cloned.

Asunto(s)

RESUMEN

BACKGROUND: Hardwood spent sulfite liquor (HSSL) is a by-product of acid sulfite pulping process that is rich in xylose, a monosaccharide that can be fermented to ethanol by Scheffersomyces stipitis. However, HSSL also contains acetic acid and lignosulfonates that are inhibitory compounds of yeast growth. The main objective of this study was the use of an evolutionary engineering strategy to obtain variants of S. stipitis with increased tolerance to HSSL inhibitors while maintaining the ability to ferment xylose to ethanol. RESULTS: A continuous reactor with gradually increasing HSSL concentrations, from 20% to 60% (v/v), was operated for 382 generations. From the final obtained population (POP), a stable clone (C4) was isolated and characterized in 60% undetoxified HSSL. C4 isolate was then compared with both the parental strain (PAR) and POP. Both POP and C4 were able to grow in 60% undetoxified HSSL, with a higher capability to withstand HSSL inhibitors than PAR. Higher substrate uptake rates, 7% higher ethanol efficiency and improved ethanol yield were obtained using C4. CONCLUSION: S. stipitis was successfully adapted to 60% (v/v) undetoxified eucalyptus HSSL. A stable isolate, C4, with an improved performance in undetoxified HSSL compared to PAR was successfully obtained from POP. Owing to its improved tolerance to inhibitors, C4 may represent a major advantage for the production of bioethanol using HSSL as substrate.

RESUMEN

Spent sulfite liquor is a lignocellulosic waste obtained after the sulfite pulping process. It is mainly formed by sugars and lignosulfonates which are isolated from the pulp during the cooking process. The current work investigates the kinetic modeling of the sulfite process from a biorefinery point of view since monosaccharides present in the spent liquor can be used as a raw material in further biorefinery processes to produce other value-added products. Kinetic parameters of carbohydrate degradation have been determined following sugar and inhibitors from wood to spent liquor, using laboratory scale reactors and different temperatures, 130, 140 and 150 °C. Three types of reaction schemes were developed. Kinetic parameters were obtained for each one using first and n order reactions, using Aspen Custom Modeler. Results show that the best temperature to be used in the process is 130 °C, giving the maximum sugar conversion, 33.91 mol% and obtaining 13.81 mol% of decomposition products.

Asunto(s)

RESUMEN

Halophilic microorganisms thrive at elevated concentrations of sodium chloride up to saturation and are capable of growing on a wide variety of carbon sources like various organic acids, hexose and also pentose sugars. Hence, the biotechnological application of these microorganisms can cover many aspects, such as the treatment of hypersaline waste streams of different origin. Due to the fact that the high osmotic pressure of hypersaline environments reduces the risk of contamination, the capacity for cost-effective non-sterile cultivation can make extreme halophilic microorganisms potentially valuable organisms for biotechnological applications. In this contribution, the stepwise use of screening approaches, employing design of experiment (DoE) on model media and subsequently using industrial waste as substrate have been implemented to investigate the applicability of halophiles to generate PHB from the industrial waste stream spent sulfite liquor (SSL). The production of PHB on model media as well as dilutions of industrial substrate in a complex medium has been screened for by fluorescence microscopy using Nile Blue staining. Screening was used to investigate the ability of halophilic microorganisms to withstand the inhibiting substances of the waste stream without negatively affecting PHB production. It could be shown that neither single inhibiting substances nor a mixture thereof inhibited growth in the investigated range, hence, leaving the question on the inhibiting mechanisms open. However, it could be demonstrated that some haloarchaea and halophilic bacteria are able to produce PHB when cultivated on 3.3% w/w dry matter spent sulfite liquor, whereas H. halophila was even able to thrive on 6.6% w/w dry matter spent sulfite liquor and still produce PHB.