RESUMEN

The stability, reproducibility and engineering of SERS substrate faces a great challenge in melamine SERS assay. In this work, a simple, highly sensitive, stable and cost-efficient SERS detection platform for melamine was established based on its Raman fingerprints spectrum. The Ag@ porous silicon photonic crystal (Ag@PPC) was prepared as the 3D SERS substrate by electrochemical etching and magnetron sputter technology. The main influence factors for the preparation of SERS substrate were investigated in detail. The analytical enhancement factor of the 3D SERS substrate can reach to 2.6 × 108. The 3D SERS detection platform showed a wide linear detection range of 10-4∼10 mg L-1 and a low limit of detection of 0.1 µg L-1 for melamine. Moreover, such detection platform showed good stability, high reproducibility and high recovery rates for melamine. The 3D Ag@PPC SERS substrate can be easily prepared and engineered, displaying a great potential application in food safety field.

RESUMEN

In this work, a boric-acid-modified Fe3O4@Au@BA-MOF composite material as a multifunctional SERS substrate was ingeniously constructed for detecting both pathogens and antibiotics as well as photothermally inactivating the pathogens. Through improving the dispersity and stability of gold nanoparticles (Au NPs), leveraging the specificity of boric acid (BA) groups in recognizing cis-diol structures, and the ability of SERS technology to provide unique fingerprint spectra of targets, the sensitive and stable detection of pathogens and antibiotics was achieved. Compared with Au NPs and Fe3O4@Au, the SERS enhancement factor of Fe3O4@Au@BA-MOF was 4.31 × 106, which was about 400 times and 16 times higher than the former two, respectively. Among the existing work, the limit of detection for pathogens was lower or comparable, and it exhibited good stability, maintaining consistent performance for 23 days. Additionally, this substrate achieved efficient photothermal inactivation of pathogens under both near-infrared light and natural light excitation. Within 8 min of near-infrared light irradiation, the bactericidal rates for Staphylococcus aureus and Escherichia coli reach 100% and 99.3%, respectively.

RESUMEN

Herein we report a wearable sweat sensor of a Janus fabric based on surface enhanced Raman scattering (SERS) technology, mainly detecting the two important metabolites glucose and lactate. Janus fabric is composed of electrospinning PU on a piece of medical gauze (cotton), working as the unidirectional moisture transport component (R = 1305%) to collect and transfer sweat efficiently. SERS tags with different structures act as the probe to recognize and detect the glucose and lactate in high sensitivity. Core-shell structured gold nanorods with DTNB inside (AuNRs@DTNB@Au) are used to detect lactate, while gold nanorods with MPBA (AuNRs@MPBA) are used to detect glucose. Through the characteristic SERS information, two calibration functions were established for the concentration determination of glucose and lactate. The concentrations of glucose and lactate in sweat of a 23 years volunteer during three-stage interval running are tested to be 95.5, 53.2, 30.5 µM and 4.9, 13.9, 10.8 mM, indicating the glucose (energy) consumption during exercise and the rapid accumulation of lactate at the early stage accompanied by the subsequent relief. As expected, this sensing system is able to provide a novel strategy for effective acquisition and rapid detection of essential biomarkers in sweat.

Asunto(s)

RESUMEN

A core-shell-shell sandwich material is developed with silver nanowires as the core, ZIF-8 as an inner shell, and gold nanoparticles as the outer shell, namely, Ag@ZIF-8@Au nanowires (AZA-NW). Then, the synthesized AZA-NW is transformed into a surface-enhanced Raman spectroscopy (SERS) sensor (named M-AZA) by the vacuum filtration method and used to enrich, detect, and inactivate traces of bacteria in the environment. The M-AZA sensor has three main functions: (1) trace bacteria are effectively enriched, with an enrichment efficiency of 91.4%; (2) ultrasensitive detection of trace bacteria is realized, with a minimum detectable concentration of 1 × 101 CFU/mL; (3) bacteria are effectively killed up to 92.4%. The shell thickness of ZIF-8 (5-75 nm) is controlled by adjusting the synthesis conditions. At an optimum shell thickness of 15 nm, the effect of gold nanoparticles and ZIF-8 shell on the sensor's stability, SERS activity, and antibacterial performance is investigated. The simulation of the SERS sensor using the finite difference time domain (FDTD) method is consistent with the experimental results, theoretically demonstrating the role of the gold nanoparticles and the ZIF-8 shell. The sensor also shows excellent stability, safety, and generalizability. The campus water sample is then tested on-site by the M-AZA SERS sensor, indicating its potential for practical applications.

Asunto(s)

RESUMEN

Tailoring a material's surface with hierarchical structures from the micro- to the nanoscale is key for fabricating highly sensitive detection platforms. To achieve this, the fabrication method should be simple, inexpensive, and yield materials with a high density of surface features. Here, using benchtop fabrication techniques, gold surfaces with hierarchically structured roughness are generated for sensing applications. Hierarchical gold electrodes are prepared on pre-stressed polystyrene substrates via electroless deposition and amperometric pulsing. Electrodes fabricated using 1 mm H[AuCl4] and roughened with 80 pulses revealed the highest electroactive surface area. These electrodes are used for enzyme-free detection of glucose in the presence of bovine serum albumin and achieved a limit of detection of 0.36 mm, below glucose concentrations in human blood. The surfaces nanoroughened with 100 pulses also showed excellent surface-enhanced Raman scattering (SERS) response for the detection of rhodamine 6G, with an enhancement factor of ≈2 × 106 compared to detection in solution, and for the detection of a self-assembled monolayer of thiophenol, with an enhancement factor of ≈30 compared to the response from microstructured gold surfaces. It is envisioned that the simplicity and low fabrication cost of these gold-roughened structures will expedite the development of electrochemical and SERS sensing devices.

RESUMEN

Exosome-based liquid biopsies possess great potential in monitoring cancer development However, current exosome detection biosensors require large exosome volumes, showing the weak detection sensitivity. Besides, these methods pay little attention to in situ analysis of exosomes, hence limiting the provision of more accurate clinically-relevant information. Herein, we develop an innovative label-free biosensor combining the low-cost thermophoretic enrichment method with the surface-enhanced Raman spectroscopy (SERS) detection. Based on the thermophoretic enrichment strategy, exosomes and gold nanoparticles can be enriched together into a small area with a scale of 500 µm within 10 min. The Raman signals of various exosomes derived from normal, cancerous cell lines and human serum are dynamically monitored in situ, with the limit of detection of 102-103 particles per microliter, presenting higher sensitivity compared with the similar label-free SERS detection. The spectral data set of different exosomes is applied to train for multivariate classification of cell types and to estimate how the normal exosome data resemble cancer cell exosome. The reliable classification and identification of different exosomes can be realized. The current biosensor is convenient, low-cost and requires small exosome volumes (∼3 µL), and if validated in larger cohorts may contribute to the tumor prediction and diagnosis.

Asunto(s)

RESUMEN

Flexible laser-scribed graphene (LSG) substrates with gold nanoislands have been developed as biochips for in situ electrochemical (EC) and surface-enhanced Raman scattering (SERS) biodetection (biomolecules and viral proteins). A flexible biochip was fabricated using CO2 laser engraving polyimide (PI) films to form a 3D porous graphene-like nanostructure. Gold nanoislands were deposited on the LSG substrates to enhance the intensity of the Raman signals. Moreover, the addition of auxiliary and reference electrodes induced a dual-function EC-SERS biochip with significantly enhanced detection sensitivity. The biochip could selectively and easily capture SARS-CoV-2 S1 protein through the SARS-CoV-2 S1 antibody immobilized on EC-SERS substrates using 1-ethyl-(3-dimethylaminopropyl)carbodiimide (EDC) and N-hydroxysuccinimide (NHS). The grafted antibody specifically bound to SARS-CoV-2, resulting in a significant increase in the SERS signal of the target analyte. The limit of detection (LOD) of the SARS-CoV-2 S1 protein was 5 and 100 ng/mL by using EC and SERS detection, respectively. Although the LOD of the SARS-CoV-2 S1 protein detected using SERS is only 100 ng/mL, it can provide fingerprint information for identification. To improve the LOD, EC detection was integrated with SERS detection. The three-electrode detection chip enables the simultaneous detection of SERS and EC signals, which provides complementary information for target identification. The dual-functional detection technology demonstrated in this study has great potential for biomedical applications, such as the rapid and sensitive detection of SARS-CoV-2.

Asunto(s)

RESUMEN

The unreasonable spraying and random migration of acetamiprid may cause pollution of crops, soil and water resources in the environment, resulting in threatening ecosystem and human health. However, the monitoring of acetamiprid using mass spectrum in the environment encounters challenges due to high-cost instruments and complex processing time. Herein, we fabricated a rapid and reliable SERS method based on Ag@ZIF-8@Au platforms for tracing acetamiprid residues in the environment. In this method, a MOF material named ZIF-8 is coated with silver nanoparticles and distributed internally between AgNPs and AuNPs to enhance Raman signal, which can enrich pesticide molecules into the hotspots area provided by noble material and helps avoid the oxidation of silver nanoparticles. High sensitivity (LOD of 9.027 × 10-10 M for acetamiprid, and SERS enhancement factor of 4.3 × 107), excellent reproducibility (6.496% or 7.198% RSD for 30 random points) and superior stability (3.127% RSD for 6 weeks) were achieved using the proposed method. Acetamiprid with concentrations from 10-4 to 10-9 M were successfully detected by SERS method. Furthermore, the linear detection models of acetamiprid in different environment matrices (lake water, tea leaves, tea garden soil, oranges and oranges orchard soil) were established and all the correlation coefficient (R2) were higher than or equal to 95%, indicating the excellent adaptability of Ag@ZIF-8@Au platform in environment. The randomly spiked concentrations of acetamiprid were also tested with good recovery values and low relative error values, further confirming the reliability of the detection method.

Asunto(s)

RESUMEN

The global environmental concern surrounding microplastic (MP) pollution has raised alarms due to its potential health risks to animals, plants, and humans. Because of the complex structure and composition of microplastics (MPs), the detection methods are limited, resulting in restricted detection accuracy. Surface enhancement of Raman spectroscopy (SERS), a spectral technique, offers several advantages, such as high resolution and low detection limit. It has the potential to be extensively employed for sensitive detection and high-resolution imaging of microplastics. We have summarized the research conducted in recent years on the detection of microplastics using Raman and SERS. Here, we have reviewed qualitative and quantitative analyses of microplastics and their derivatives, as well as the latest progress, challenges, and potential applications.

Asunto(s)

RESUMEN

Inspired by ordered photonic crystals and structural color materials in nature, we successfully prepared hydroxypropyl cellulose (HPC) photonic films with ordered surface arrays by double-imprint soft lithography. Then we introduced another important material of the cellulose family, cellulose nanocrystals (CNC), which has liquid crystal nature and birefringent properties of the particles, into the system to realize the single-point shrinkage of the film array and the control of structural color. Through multi-component doping and concentration control, we further optimized the multi-scale structure of the materials, and obtained HPC/CNCs composite photonic films with excellent properties in color, stability and flexibility, whose elastic modulus and tensile properties are significantly higher than those of single-component. Further loading of SiO2@PDA enhances the color saturation and realizes the in-situ reduction of metal ions on the film surface. This plasma film can track a variety of substances with high sensitivity and long-term stability, showing potential application prospects in the field of surface-enhanced Raman scattering (SERS), which provides a potential possibility for chiral structures to be used in the field of biosensor detection and circularly polarized luminescence.

RESUMEN

The prevalence of sulfonamide residues in aquatic environments poses serious environmental risks, and the sensitive detection and effective degradation of sulfonamides have attracted widespread attention. Here, the environmentally friendly chitosan (CS)/carbon nitride (CN) with three-dimensional porous structure is fabricated by freeze-drying method, and subsequently a new bifunctional flexible substrate (CS/CN/Ag) is prepared by anchoring of small sized AgNPs (6 ∼ 12 nm) on CS/CN. Importantly, the CS/CN/Ag substrate shows high adsorption capacity (∼ 83.06%) for sulfamethoxazole (SMX) solution within 20 mins and the limit of detection can be as low as 7.46 × 10-9 mol·L-1 with an enhancement factor of 3.3 × 105. Also, the CS/CN/Ag substrate displays highly selective for surface-enhanced Raman spectroscopy (SERS) detection of sulfonamides and also shows excellent SERS response for SMX in hospital wastewater samples. In addition, the photocatalytic degradation efficiency of SMX could reach as high as 99.22% within 20 mins of irradiation and the CS/CN/Ag still maintains outstanding photocatalytic performance after six cycles. Moreover, the Ag content in the CS/CN/Ag substrate is only 2.35%, and also the CS/CN/Ag exhibits good uniformity, repeatability, recyclability and stability. Therefore, this flexible and cost-effectively substrate of CS/CN/Ag shows great potential for the simultaneous SERS detection and photocatalytic degradation of pollutants in actual wastewater samples.

RESUMEN

Volatile organic compounds (VOCs), particularly monoaromatic hydrocarbon compounds (MACHs), pose a potential risk to the atmospheric environment and human health. Therefore, the progressive development of efficient detection methodologies is a pertinent need, which is still a challenge at present. In this study, we present a rapid and sensitive method to detect trace amounts of MACHs using a bifunctional SERS composite substrate. We prepared an Au/SiO2 enhanced layer and a porous Cu(OH)2 adsorption layer via microfluidic-assisted gas-liquid interface self-assembly. The composite substrate effectively monitored changes in benzaldehyde using time-varying SERS spectra, and track-specifically identified various VOCs such as benzene, xylene, styrene, and nitrobenzene. In general, the substrate exhibited a rapid response time of 20 s to gaseous benzaldehyde, with a minimum detection concentration of less than 500 ppt. Further experimental assessments revealed an optimum Cu(OH)2 thickness of the surrounding adsorption layer of 150 nm, which can achieve an efficient SERS response to MACHs. Furthermore, the recoverable and reusable property of the composite substrate highlights its practicality. This study presents a straightforward and efficient approach for detecting trace gaseous VOCs using SERS, with significant implications in the designing of SERS substrates for detecting other VOCs.

RESUMEN

Tea plants absorb chromium-contaminated soil and water and accumulate in tea leaves. Hexavalent chromium (Cr6+) is a very toxic heavy metal; excessive intake of tea containing Cr6+ can cause serious harm to human health. A reliable and sensitive surface-enhanced Raman spectroscopy (SERS) method was developed using Au@Ag nanoparticles as an enhanced substrate for the determination of Cr6+ in tea. The Au@AgNPs coated with carbimazole showed a highly selective reaction to Cr6+ in tea samples through a redox reaction between Cr6+ and carbimazole. The Cr6+ in the contaminated tea sample reacted with methimazole-the hydrolysate of carbimazole-to form disulfide, which led to the decrease in the Raman intensity of the peak at 595 cm-1. The logarithm of the concentration of Cr6+ has a linear relationship with the Raman intensity at the characteristic peak and showed a limit of detection of 0.945 mg/kg for the tea sample. The carbimazole functionalized Au@AgNPs showed high selectivity in analyzing Cr6+ in tea samples, even in the presence of other metal ions. The SERS detection technique established in this study also showed comparable results with the standard ICP-MS method, indicating the applicability of the established technique in practical applications.

RESUMEN

Antibiotic residues in aquaculture environments disrupt the ecosystem balance and pose a potential hazard to human health when entering the food chain. Therefore, ultra-sensitive detection of antibiotics is necessary. In this study, a multifunctional Fe3O4@mTiO2@Ag core-shell nanoparticle (NP), synthesized using a layer-by-layer method, was demonstrated to be useful as an enhanced substrate for in-situ surface-enhanced Raman spectroscopy (SERS) detection of various quinolone antibiotics in aqueous environments. The results showed that the minimum detectable concentrations of the six investigated antibiotics were 1 × 10-9 mol/L (ciprofloxacin, danofloxacin, enoxacin, enrofloxacin, and norfloxacin) and 1 × 10-8 mol/L (difloxacin hydrochloride) under the enrichment and enhancement of Fe3O4@mTiO2@Ag NPs. Additionally, there was a good quantitative relationship between the antibiotics concentrations and SERS peak intensities within a certain detection range. The results of the spiked assay of actual aquaculture water samples showed that the recoveries of the six antibiotics ranged from 82.9% to 113.5%, with relative standard deviations ranging from 1.71% to 7.24%. In addition, Fe3O4@mTiO2@Ag NPs achieved satisfactory results in assisting the photocatalytic degradation of antibiotics in aqueous environments. This provides a multifunctional solution for low concentration detection and efficient degradation of antibiotics in aquaculture water.

Asunto(s)

RESUMEN

The accurate, sensitive and portable detection of morphine is important to handle judicial cases, but remains to be a great challenge. In this work, a flexible route is presented for the accurate identification and efficient detection of trace morphine in solutions based on surface-enhanced Raman spectroscopy (SERS) and a solid substrate/chip. A gold-coated jagged silicon nanoarray (Au-JSiNA) is designed and prepared via Si-based polystyrene colloidal template-reactive ion etching and sputtering deposition of Au. Such Au-JSiNA has three-dimensional nanostructure with good structural uniformity, high SERS activity and hydrophobic surface. Adopting this Au-JSiNA as SERS chip, trace morphine in solutions could be detected and identified in both dropping and soaking ways, and the limit of detection is below 10-4 mg/mL. Importantly, such chip is especially suitable for the detection of trace morphine in aqueous solutions and even domestic sewage. The good SERS performance is attributed to the high-density nanotips and nanogaps on this chip as well as its hydrophobic surface. Additionally, the appropriate surface modification of this Au-JSiNA chip with 3-mercapto-1-propanol or 3-mercaptopropionic acid/1-(3-dimethylaminopropyl)-3-ethylcarbodiimide can further increase its SERS performances to morphine. This work provides a facile route and practical solid chip for SERS detection of trace morphine in solutions, which is significant to develop the portable and reliable instruments for on-site analysis of drugs in solutions.

RESUMEN

We demonstrate wrinkle-bioinspired flexible SERS sensor covered by silver nanowire (AgNWs) network for the detection of pesticide molecules. Compared with the silver film deposition substrates, the wrinkle-bioinspired AgNWs SERS substrates show stronger SERS effect, which were attributed to the electromagnetic field enhancement posed by the relatively high density "hot spots" of AgNWs. In order to investigate the adsorption performance of wrinkle-bioinspired flexible sensors, we measured the corresponding contact angles of AgNWs on the substrate surfaces before and after plasma treatment and found that the AgNWs treated with plasma are more hydrophilic than that without plasma treatment. Additionally, the wrinkle-bioinspired SERS sensors show different SERS activities under different tensile strain, and the 10-6 mol/L concentration of Rhodamine dye (R6G) molecules can be detected by portable Raman spectra, reducing greatly detection cost. The surface plasmon resonance of AgNWs is induced by adjusting the deformation of AgNWs substrate, enhancing the SERS signal. This reliability of wrinkle-bioinspired SERS sensors is further verified by in situ detection of pesticide molecules.

Asunto(s)

RESUMEN

Ultraviolet lithography is a very promising technology used for the batch fabrication of biomedical microswimmers. However, creating microswimmers that can swim at low Reynolds number using biocompatible materials while retaining strong magnetic properties and excellent biomedical functionality is a great challenge. Most of the previously reported biomedical microswimmers possess either strong magnetic properties by using non-biocompatible nickel coating or good biocompatibility by using iron oxide particle-embedded hydrogel with weak magnetism, but not both. Alternatively, iron oxide nanoparticles can be coated on the surface of microswimmers to improve magnetic properties; however, this method limited the usability of the microswimmers' surfaces. To address these shortcomings, this work utilized an in situ synthesis technique to generate high magnetic content inside hydrogel-based achiral planar microswimmers while leaving their surfaces free to be functionalized for SERS detection. The hydrogel matrices of the magnetically actuated hydrogel-based microswimmers were first prepared by ultraviolet lithography. Then, the high concentration of iron oxide was achieved through multiple continuous in situ coprecipitation cycles. Finally, the SERS detection capability of magnetically actuated hydrogel-based microswimmers was enabled by uniformly growing silver nanoparticles on the surface of the microswimmers. In the motion control tests, the microswimmers showed a high swimming efficiency, high step-out frequency, and consistent synchronized motion. Furthermore, the magnetically actuated hydrogel-based microswimmers were able to improve the detection efficiency of analytes under magnetic guidance.

RESUMEN

Rapid identification and quantitative simultaneous analysis for multiple pesticide in real samples based on surface-enhanced Raman spectroscopy (SERS) is still a challenge because of sample complexity, reproducibility, and stability of SERS substrate. With use of colloidal silver nanoparticles loaded three-dimensional (3D) silica photonic microspheres (SPMs) array as the analytical platform, a SERS-based array assay for multiple pesticides was developed in this work. The silver nanoparticles were fixed into the gaps formed by the self-assembled nanospheres of the 3D SPMs to produce "hot spots", on which the Raman enhanced effect was up to 9.86 × 107 and the maximum electric field enhancement effect reached to 9.75 times, ensuring the target pesticides on the surface of the SERS-substrate integrated SPM can be detected sensitively. Using 2,4-dichlorophenoxyacetic acid (2,4-D), glyphosate, and imidacloprid as the testing pesticides, the label-free and high-throughput SERS assay for simultaneous detection of the pesticides was established, giving good linear detection ranges (0.1-204.8 µg/mL for 2,4-D, 0.3-247.9 µg/mL for glyphosate, and 0.2-204.8 µg/mL for imidacloprid) and low detection limits (3.03 ng/mL for 2,4-D, 3.14 ng/mL for glyphosate, and 8.82 ng/mL for imidacloprid). The spiked recovery rates in the real samples were measured in the range of 82-112%, which was consistent with that of the classical standard methods. The label-free 3D SERS array analytical platform provides a powerful tool for high-throughput and low-cost screening of multiple pesticide residues in real samples.

Asunto(s)

RESUMEN

Wearable, noninvasive, and simultaneous sensing of subtle strains and eccrine molecules on human body is essential for future health monitoring and personalized medicine. However, there is a huge chasm between biomechanics and bio/chemical molecule detections. Here, a wearable plasmonic bridge sensor with multiple abilities to monitor subtle strains and molecules is developed. Hollow Au-Ag nano-rambutans and carbon nanotubes (CNTs) are adsorbed in the nonwoven fabrics (NWFs) conjointly, where the gap between the conducting network of CNTs is bridged by the Au-Ag nano-rambutans during the subtle strain sensing, and the detection sensitivity for stress is improved at least 1 order of magnitude compared to that with the only CNTs. In order to acquire the accurate human action recognition, a machine learning algorithm (support vector machines) based on output biomechanics data is designed. The average accuracy of our plasmonic bridge sensor reaches 89.0% for human action recognition. Moreover, due to the hollow structure and high nanoroughness, the single Au-Ag nano-rambutan particle has strong localized surface plasmon resonance effect and high surface-enhanced Raman scattering (SERS) activity. Based on their unique SERS spectra introduced by the hollow Au-Ag nano-rambutan adsorbed in the NWFs, noninvasive extraction and "fingerprint" recognition of bio/chemical molecules could be realized during the wearable sensing. In sum, the NWFs/CNTs/Au-Ag sensor bridges the barrier between the bodily strain detection and molecule recognition during the wearable sensing. Such integrated and multifunctional sensing strategy for universal biomechanics and bio/chemical molecules means to assess human health to be of importance.

Asunto(s)

RESUMEN

In this study, we developed a filtering material for facial masks, which is capable of trapping and subsequent inactivation of bacteria under white light emitting diodes (LED) or sunlight irradiation. Such a functionality is achieved via the modification of the composite membrane based on porous polymer with photocatalytic (TiO2) and plasmonic (Ag) nanoparticles. The porous polymer is produced by means of a computer numerical control machine, which rolls a photoresist/thermoplastic mixture into a ~20-µm-thick membrane followed by its thermal/ultraviolet (UV) hardening and porosification. TiO2 nanoparticles are prepared by hydrothermal and sol-gel techniques. Colloidal synthesis is utilized to fabricate Ag nanoparticles. The TiO2 photocatalytic activity under UV excitation as well as a photothermal effect generated by plasmonic Ag nanoparticles subjected to LED irradiation are studied by the assessment of methylene blue (MB) decomposition. We demonstrate that, in contrast to the filter of the standard facial medical mask, the polymer membrane modified with spray-coated TiO2 and Ag nanoparticles prevents the penetration of bacillus subtilis from its top to bottom side and significantly inhibits bacterial growth when exposed to LED or sunlight.