RESUMEN

Background: Understanding the risk factors leading to intracranial aneurysm (IA) rupture have still not been fully clarified. They are vital for proper medical guidance of patients harboring unruptured IAs. Clarifying the hemodynamics associated with the point of rupture could help could provide useful information about some of the risk factors. Thus far, few studies have studied this issue with often diverging conclusions. Methods: We identified a point of rupture in patients operated for an IAs during surgery, using a combination of preoperative computed tomography (CT) and computed tomography angiography (CTA). Hemodynamic parameters were calculated both for the aneurysm sac as a whole and the point of rupture. In two cases, the results of CFD were compared with those of the experiment using particle image velocimetry (PIV). Results: We were able to identify 6 aneurysms with a well-demarcated point of rupture. In four aneurysms, the rupture point was near the vortex with low wall shear stress (WSS) and high oscillatory shear index (OSI). In one case, the rupture point was in the flow jet with high WSS. In the last case, the rupture point was in the significant bleb and no specific hemodynamic parameters were found. The CFD results were verified in the PIV part of the study. Conclusion: Our study shows that different hemodynamic scenarios are associated with the site of IA rupture. The numerical simulations were confirmed by laboratory models. This study further supports the hypothesis that various pathological pathways may lead to aneurysm wall damage resulting in its rupture.

RESUMEN

The USP Rotating Basket Dissolution Testing Apparatus 1 is listed in the USP as one of the tools to assess dissolution of oral solid dosage forms. Baskets of different mesh sizes can be used to differentiate between dissolution profiles of different formulations. Here, we used Particle Image Velocimetry (PIV) to study the hydrodynamics of the USP Apparatus 1 using baskets with different mesh openings (10-, 20- and 40-mesh) revolving at 100 rpm, when the vessel was filled with 500 mL. The velocity profiles throughout the liquid were found to vary significantly using baskets of different mesh sizes, typically increasing with increased size of the opening of the basket mesh, especially for axial and radial velocities. This, in turn, resulted in a significantly different flow rate through the basket, which can be expected to significantly impact the dissolution rate of the drug product. A comparison between the results of this work with those of a previous study with a 900-mL fill volume (Sirasitthichoke et al., Intern. J. Pharmaceutics, 2021, 607: 120976), shows that although the hydrodynamics in the USP Apparatus 1 changed with fill level in the vessel, the flow rate through the basket was not significantly affected. This implies that tablets dissolving in the two systems would experience similar tablet-liquid medium mass transfer coefficients, and therefore similar initial dissolution rates, but different dissolution profiles because of the difference in volume.

Asunto(s)

RESUMEN

Sessile barnacles feed by sweeping their basket-like cirral fan through the water, intercepting suspended prey. A primary component of the diet of adult barnacles is copepods that are sensitive to fluid disturbances and capable of escaping. How do barnacles manage to capture copepods despite the fluid disturbances they generate? We examined this question by describing the feeding current architecture of 1 cm sized Balanus crenatus using particle image velocimetry, and by studying the trajectories of captured copepods and the escapes of evading copepods. We found that barnacles produce a feeding current that arrives both from behind and the sides of the barnacle. The flow from the sides represents quiescent corridors of low fluid deformation and uninterrupted by the beating cirral fan. Potential prey arriving from behind are likely to encounter the cirral fan and, hence, capture here is highly unlikely. Accordingly, most captured copepods arrived through the quiet corridors, while most copepods arriving from behind managed to escape. Thus, it is the unique feeding flow architecture that allows feeding on evasive prey. We used the Landau-Squire jet as a simple model of the feeding current. For the Reynolds number of our experiments, the model reproduces the main features of the feeding current, including the lateral feeding corridors. Furthermore, the model suggests that smaller barnacle specimens, operating at lower Reynolds numbers, will produce a fore-aft symmetric feeding current without the lateral corridors. This suggests an ontogenetic diet shift from non-evasive prey to inclusion of evasive prey as the barnacle grows.

Asunto(s)

RESUMEN

Fluid flow behavior is visualized through particle image velocimetry (PIV) for understanding and studying experimental fluid dynamics. However, traditional PIV methods require multiple cameras and conventional lens systems for image acquisition to resolve multi-dimensional velocity fields. In turn, it introduces complexity to the entire system. Meta-lenses are advanced flat optical devices composed of artificial nanoantenna arrays. It can manipulate the wavefront of light with the advantages of ultrathin, compact, and no spherical aberration. Meta-lenses offer novel functionalities and promise to replace traditional optical imaging systems. Here, a binocular meta-lens PIV technique is proposed, where a pair of GaN meta-lenses are fabricated on one substrate and integrated with a imaging sensor to form a compact binocular PIV system. The meta-lens weigh only 116 mg, much lighter than commercial lenses. The 3D velocity field can be obtained by the binocular disparity and particle image displacement information of fluid flow. The measurement error of vortex-ring diameter is ≈1.25% experimentally validates via a Reynolds-number (Re) 2000 vortex-ring. This work demonstrates a new development trend for the PIV technique for rejuvenating traditional flow diagnostic tools toward a more compact, easy-to-deploy technique. It enables further miniaturization and low-power systems for portable, field-use, and space-constrained PIV applications.

RESUMEN

An interventional robot is a means for vascular diagnosis and treatment, and it can perform dredging, releasing drug and operating. Normal hemodynamic indicators are a prerequisite for the application of interventional robots. The current hemodynamic research is limited to the absence of interventional devices or interventional devices in fixed positions. Considering the coupling effect of blood, vessels and robots, based on the bi-directional fluid-structure interaction, using the computational fluid dynamics and particle image velocimetry methods, combined with the sliding and moving mesh technologies, we theoretically and experimentally study the hemodynamic indicators such as blood flow lines, blood pressure, equivalent stress, deformation and wall shear stress of blood vessels when the robot precesses, rotates or does not intervene in the pulsating blood flow. The results show that the intervention of the robot increase the blood flow rate, blood pressure, equivalent stress and deformation of the vessels by 76.4%, 55.4%, 76.5%, and 346%, respectively. The operating mode of the robot during low-speed operation has little impact on the hemodynamic indicators. Using the methyl silicone oil as the experimental fluid, the elastic silicone pipe as the experimental pipe, and the intervention robot having a bioplastic outer shell, the velocity of the fluid around the robot is measured on the developed experimental device for fluid flow field in a pulsating flow when the robot runs. The experimental results are similar to the numerical results. Our work provides an important reference for the hemodynamic study and optimization of the mobile interventional devices.

Asunto(s)

RESUMEN

Particle image velocimetry has been widely used in various sectors from the automotive to aviation, research, and development, energy, medical, turbines, reactors, electronics, education, refrigeration for flow characterization and investigation. In this study, articles examined in open literature containing the particle image velocimetry techniques are reviewed in terms of components, lasers, cameras, lenses, tracers, computers, synchronizers, and seeders. The results of the evaluation are categorized and explained within the tables and figures. It is anticipated that this paper will be a starting point for researchers willing to study in this area and industrial companies willing to include PIV experimenting in their portfolios. In addition, the study shows in detail the advantages and disadvantages of past and current technologies, which technologies in existing PIV laboratories can be renewed, and which components are used in the PIV laboratories to be installed.

RESUMEN

Objective To investigate the effect of left ventricular assist device (LVAD) and aortic graft angle on hemodynamics of aortic valve. Methods Three models of aorta and aortic valve with 45°, 60° and 90° anastomosis angles between LVAD and aorta were constructed, and an in vitro pulsating table was built for in vitro experiments. Using particle image velocimetry (PIV) system, three moments in the cardiac cycle ( T1 systolic peak, T rapid closure, T3 diastolic peak), were selected to study the hemodynamic state of aortic valve. Results Velocity vector, vorticity and viscous shear stress were used to evaluate the effect of LVAD anastomosis angle on hemodynamics of aortic valve. During the period of rapid valve closure, with the increase of graft angle, the blood flow velocity near the valve wall, the average vorticity and the maximum viscous shear stress all increased. Conclusions When the graft angle is lower, the impact velocity of blood on the valve is smaller, and the shear force on the valve decreases, so that the valve is in a better hemodynamic environment. This study provides references for the selection of anastomotic angles in clinical operations.

RESUMEN

Computational fluid dynamics (CFD) is widely employed to predict hemodynamic characteristics in arterial models, while not friendly to clinical applications due to the complexity of numerical simulations. Alternatively, this work proposed a framework to estimate hemodynamics in vessels based on angiography images using machine learning (ML) algorithms. First, the iodine contrast perfusion in blood was mimicked by a flow of dye diffusing into water in the experimentally validated CFD modeling. The generated projective images from simulations imitated the counterpart of light passing through the flow field as an analogy of X-ray imaging. Thus, the CFD simulation provides both the ground truth velocity field and projective images of dye flow patterns. The rough velocity field was estimated using the optical flow method (OFM) based on 53 projective images. ML training with least absolute shrinkage, selection operator and convolutional neural network was conducted with CFD velocity data as the ground truth and OFM velocity estimation as the input. The performance of each model was evaluated based on mean absolute error and mean squared error, where all models achieved or surpassed the criteria of 3 × 10-3 and 5 × 10-7 m/s, respectively, with a standard deviation less than 1 × 10-6 m/s. Finally, the interpretable regression and ML models were validated with over 613 image sets. The validation results showed that the employed ML model significantly reduced the error rate from 53.5% to 2.5% on average for the v-velocity estimation in comparison with CFD. The ML framework provided an alternative pathway to support clinical diagnosis by predicting hemodynamic information with high efficiency and accuracy.

RESUMEN

Under the global landscape of the prolonged COVID-19 pandemic, the number of individuals who need to be tested for COVID-19 through screening centers is increasing. However, the risk of viral infection during the screening process remains significant. To limit cross-infection in screening centers, a non-contact mobile screening center (NCMSC) that uses negative pressure booths to improve ventilation and enable safe, fast, and convenient COVID-19 testing is developed. This study investigates aerosol transmission and ventilation control for eliminating cross-infection and for rapid virus removal from the indoor space using numerical analysis and experimental measurements. Computational fluid dynamics (CFD) simulations were used to evaluate the ventilation rate, pressure differential between spaces, and virus particle removal efficiency in NCMSC. We also characterized the airflow dynamics of NCMSC that is currently being piloted using particle image velocimetry (PIV). Moreover, design optimization was performed based on the air change rates and the ratio of supply air (SA) to exhaust air (EA). Three ventilation strategies for preventing viral transmission were tested. Based on the results of this study, standards for the installation and operation of a screening center for infectious diseases are proposed.

RESUMEN

The modelling of turbulence for IC engine applications is quite a challenging task. Large Eddy Simulation (LES) is the best approach to model the turbulence as the flow is three dimensional, chaotic, transient, diffusive, dissipative and intermittent. In this paper, a Computational Fluid Dynamics (CFD) data of in-cylinder air movement on TUD (Technische universitat Darmstadt) through Reynolds Average Navier-Stokes (RANS) approach with two different turbulence model, viz. Re-Normalized Group (RNG), K-Epsilon (k-ε) and K-Omega (k-ω) turbulence models for a single-cylinder, spark-ignition engine is analyzed. A commercial code STAR-CD (Solver for turbulent flow in arbitrary regions-Computational Dynamics) which works based on finite volume method is used for numerical analysis. Qualitative and quantitative data resemblance at a particular crank angle of interest throughout the inlet and compression stroke is analysed. CFD data was compared using the experimental data conducted on a single cylinder engine using a high speed Particle Image Velocimetry (PIV) technique, which was obtained from Darmstadt Technical University. Experimental data from the published literature were difficult to obtain and hence the above data is used for comparison. The resemblance data presented here are in terms of trapped mass of air, in-cylinder pressure, fluid flow pattern into the cylinder and the spatial variation of velocity at a particular interest of location and plane on the cylinder. The data offered in this work will be useful for academic researchers attempting to undertake computational fluid dynamics studies in diesel engines.

RESUMEN

INTRODUCTION: Dry Powder Inhalers (DPIs) continue to be developed to deliver an expanding range of drugs to treat an ever-increasing range of medical conditions; with each drug and device combination needing a specifically designed inhaler. Fast regulatory approval is essential to be first to market, ensuring commercial profitability. AREAS COVERED: In vitro deposition, particle image velocimetry, and computational modeling using the physiological geometry and representative anatomy can be combined to give complementary information to determine the suitability of a proposed inhaler design and to optimize its formulation performance. In combination, they allow the entire range of questions to be addressed cost-effectively and rapidly. EXPERT OPINION: Experimental techniques and computational methods are improving rapidly, but each needs a skilled user to maximize results obtained from these techniques. Multidisciplinary teams are therefore key to making optimal use of these methods and such qualified teams can provide enormous benefits to pharmaceutical companies to improve device efficacy and thus time to market. There is already a move to integrate the benefits of Industry 4.0 into inhaler design and usage, a trend that will accelerate.

Asunto(s)

RESUMEN

Introduction: Direct quantification of hemodynamic factors applied to a cerebral aneurysm (CA) remains inaccessible due to the lack of technologies to measure the flow field within an aneurysm precisely. This study aimed to develop an in vitro validated 3D in silico patient-specific internal carotid artery sidewall aneurysm (ICASA) model which can be used to investigate hemodynamic factors on the CA pathophysiology. Methods: The validated ICASA model was developed by quantifying and comparing the flow field using particle image velocimetry (PIV) measurements and computational fluid dynamics (CFD) simulations. Specifically, the flow field characteristics, i.e., blood flowrates, normalized velocity profiles, flow streamlines, and vortex locations, have been compared at representative time instants in a cardiac pulsatile period in two designated regions of the ICASA model, respectively. One region is in the internal carotid artery (ICA) inlet close to the aneurysm sac, the other is across the middle of the aneurysmal sac. Results and Discussion: The results indicated that the developed computational fluid dynamics model presents good agreements with the results from the parallel particle image velocimetry and flowrate measurements, with relative differences smaller than 0.33% in volumetric flow rate in the ICA and relative errors smaller than 9.52% in averaged velocities in the complex aneurysmal sac. However, small differences between CFD and PIV in the near wall regions were observed due to the factors of slight differences in the 3D printed model, light reflection and refraction near arterial walls, and flow waveform uncertainties. The validated model not only can be further employed to investigate hemodynamic factors on the cerebral aneurysm pathophysiology statistically, but also provides a typical model and guidance for other professionals to evaluate the hemodynamic effects on cerebral aneurysms.

RESUMEN

The USP Apparatus 1 (rotating basket), typically used to assess drug product reproducibility and evaluate oral solid dosage forms performance, consists of a cylindrical glass vessel with a hemispherical bottom and a wire basket rotating at constant speed. Baskets with different wire openings can be used in alternative to the standard mesh opening (40-mesh) in order to discriminate between drug formulations during early stage of drug product development. Any changes introduced by different basket geometries can potentially and significantly impact the system hydrodynamics and cause variability of results, thus affecting product quality. In this work, Particle Image Velocimetry (PIV) was used to experimentally quantify the velocity distribution in the USP rotating basket Apparatus 1 using baskets of different mesh sizes (10-, 20-, and 40-mesh size) under the typical operating conditions described in dissolution testing procedures. Similar flow patterns were observed in all cases. However, the radial and axial velocities in the USP Apparatus 1 generally increased with increasingly larger openings of the basket mesh. Increasing the basket agitation speed also resulted in an overall increase in the velocities, especially below in the innermost core region below the basket, where drug fragments typically reside. More importantly, the flow entering and leaving the baskets was quantified from the velocity profiles in the immediate vicinity of the baskets. It was found that the flow increased significantly with increasingly larger mesh openings, which can, in turn, promote faster dissolution of the oral solid dosage forms, thus affecting drug dissolution profiles. Hence, the selection of the basket mesh size must be carefully considered during drug product development.

Asunto(s)

RESUMEN

Steady and pulsatile aortic stenotic flows through stenosis tubes were experimentally and numerically investigated. The objective was the understanding of the fluid dynamics in arterial geometries most relevant in the context of atherosclerosis. Axisymmetric phantoms corresponding to significant artery stenosis of 50% in diameter and severe aortic stenosis of 75% were respectively machined from silicon. A water flow circuit was established, a steady flow was provided by gravity and a pulsed flow by a pulsatile pump. At inlet Reynolds numbers in the range of 85 to 1125, flows at the stenosis region were investigated using two-component Particle Image Velocimetry (PIV). For the unsteady flow, three different heartbeats (60, 69 and 90 beats per minute) were considered. The k-ω shear-stress-transport first-order turbulence model in Computational Fluid Dynamics (CFD) commercial software was adopted for simulations. Experimental measurements of the velocity fields show good agreements with CFD for both steady and pulsed flows. Recirculation regions were found near the stenosis in both cases. Reverse flow through the stenosis was also observed in pulsatile flow during the end diastolic phase of the cycle. CFD simulations allowed us to accurately assess wall shear stress in the stenotic region where the optical measurements are very noisy. High values of wall shear stress (with high variations both in space and time), are observed, which are indicators of possible future aortic wall damage.

Asunto(s)

RESUMEN

In leaching processes controlled by diffusion and convectional transport of mass, the hydrodynamic structure formed in the reactor's working volume is an additional factor affecting the process. This research work presents results related to hydrodynamic structures developing in batch reactors, different in shape, recorded by means of the particle image velocimetry (PIV) method. The movement of the distilled water and leaching solution was analyzed during investigations. Next, the system hydrodynamics and the process of tin leaching were analyzed. Finally, the leaching is affected by the reactor geometry and the hydrodynamic structure developed in its working volume, especially when a convectional or diffusion mass transport decides the process efficiency.

RESUMEN

BACKGROUND: The haemodynamics determined by different approaches for studying fluid dynamics - i.e. computational fluid dynamics (CFD), particle image velocimetry (PIV), and phase-contrast magnetic resonance imaging (PC-MRI) - have rarely been thoroughly compared; nor have the factors that affect accuracy and precision in each method. As each method has its own advantages and limitations, this knowledge is important for future studies to be able to achieve valid analyses of fluid flows. OBJECTIVE: To gauge the capacity of these methods for analysing aneurysmal flows, we compared the haemodynamic behaviours determined by each method within a patient-specific aneurysm model. METHODS: An in vitro silicone aneurysm model was fabricated for PIV and PC-MRI, and an in silico aneurysm model with the same geometry was reconstructed for CFD. With the same fluid model prepared numerically and physically, CFD, PIV and PC-MRI were performed to study aneurysmal haemodynamics. RESULTS: 2D velocity vectors and magnitudes show good agreement between PIV and CFD, and 3D flow patterns show good similarity between PC-MRI and CFD. CONCLUSIONS: These findings give confidence to future haemodynamic studies using CFD technology. For the first time, the morphological inconsistency between the PCMRI model and others is found to affect the measurement of local flow patterns.

Asunto(s)

RESUMEN

The objective of this paper was to investigate acoustic pressure waves and the transient flow structure emitted from the single bubble near an elastic boundary based on the particle image velocimetry (PIV). A combination of an electric-spark bubble generator and PIV were used to measure the temporal bubble shapes, transient flow structure, as well as the mid-span deflection of an elastic boundary. Results are presented for three different initial positions near an elastic boundary, which were compared with results obtained using a rigid boundary. A formula relating velocity and pressure was proposed to calculate the acoustic pressure contours surrounding a bubble based on the velocity field of the transient flow structure obtained using PIV. The results show the bubbles near the elastic boundary presented a "mushroom" bubble and an inverted cone bubble. Based on the PIV-measured acoustic pressure contours, a significant pressure difference is found between the elastic boundary and the underside of the bubble, which contributed to the formation of the "mushroom" bubble and inverted cone bubble. Furthermore, the bubbles had opposite migration direction near rigid and elastic boundaries, respectively. In detail, the bubble was repelled away from the elastic boundary and the bubble was attracted by the rigid boundary. The resultant force made up of a Bjerknes force and buoyancy force dominated the migration direction of the bubble.

RESUMEN

A dual beam optical coherence tomography (OCT) instrument has been developed for flow measurement that offers advantages over microscope derived imaging techniques. It requires only a single optical access port, allows simultaneous imaging of the microfluidic channel, does not require fluorescent seed particles, and can provide a millimetre-deep depth-section velocity profile (as opposed to horizontal-section). The dual beam instrument performs rapid re-sampling of particle positions, allowing measurement of faster flows. In this paper, we develop the methods and processes necessary to make 2D quantitative measurements of the flow-velocity using dual beam OCT and present exemplar results in a microfluidic chip. A 2D reference measurement of the Poiseuille flow in a microfluidic channel is presented over a spanwise depth range of 700 m and streamwise length of 1600 m with a spatial resolution of 10 m , at velocities up to 50 m m / s . A measurement of a more complex flow field is also demonstrated in a sloped microfluidic section.

RESUMEN

A characteristic feature of obstructive lung diseases is the narrowing of small airways, which affects regional airflow patterns within the lung. However, the extent to which these patterns differ between healthy and diseased states is unknown. To investigate airflow patterns in detail, we first used particle image velocimetry measurements to validate a large eddy simulation model of flow in a patient-specific geometry. We then predicted flow patterns in the central airway under exhalation for three flow conditions-normal, intermediate, and severe-where boundary conditions represented the effect of lower airway obstructions. We computed Pearson correlation coefficients (R) to assess the similarity of flow patterns, and found that flow patterns demonstrated the greatest differentiation between flow conditions in the right main bronchi (R ≤0.60), whereas those in the secondary branches and regions of the trachea showed high correlation (R ≥0.90). These results indicate that although flow patterns are distinct between flow conditions, the choice of measurement location is critical for differentiation.

Asunto(s)

RESUMEN

Particle image velocimetry (PIV) is a commonly used method for in vitro investigation of fluid dynamics in biomedical devices, such as flow diverters for intracranial aneurysm treatment. Since it is limited to transparent blood substituting fluids like water-glycerol mixture, the influence of coagulation and platelet aggregation is neglected. We aimed at the development and the application of a modified platelet rich plasma as a new PIV fluid with blood-like rheological and coagulation properties. In standardized intracranial aneurysm silicone models, the effect of this new PIV plasma on the fluid dynamics before and after flow diverter implantation was evaluated and compared with water-glycerol measurements. The flow diverting effect was strongly dependent on the used fluid, with considerably lower velocities achieved using PIV plasma, despite the same starting viscosity of both fluids. Moreover, triggering coagulation of PIV plasma allowed for intra-aneurysmal clot formation. We presented the first in vitro PIV investigation using a non-Newtonian, clottable PIV plasma, demonstrating a mismatch to a standard PIV fluid and allowing for thrombus formation.

Asunto(s)