RESUMEN
This study investigates nanostructured titanium surfaces (Ti2 spikes) that promote the viability of osteoblasts and fibroblasts and prevent bacterial colonisation. Helium ion irradiation was adopted to produce nanometric-sized cones on titanium. Human osteoblasts (hFOB) and human gingiva fibroblasts (hGF) were used for analysis. A viability and a cytotoxicity assay were conducted to evaluate the lactate dehydrogenase (LDH) activity and assess cell damage in Ti2 spikes compared to titanium discs with a sandblasted and acid-etched (Ti2 SLA) surface. The antibacterial activity was investigated against Escherichia coli, Streptococcus mutans, Fusobacterium nucleatum, and Porphyromonas gingivalis. In the course of the cultivation, both hGF and hFOB demonstrated significantly reduced viability on the Ti2 spikes surface. hGF cells exhibited a slight but significant increase in LDH release. In contrast, hFOB showed reduced cytotoxicity on this surface. On the Ti2 spikes surface, hGF cells exhibited a significant reduction in gene expression of VCL, Src-1, and ITGα5. However, the integrin subunits ITGα1 and ITGα3 showed upregulation on the Ti2 spikes surface. The Ti2 spikes surface significantly increased the expression of almost all osteogenic markers. The results of conventional culturing demonstrated a statistically significant decrease in the number of viable cells for S. mutans, F. nucleaum, and greater quantities of P. gingivalis on Ti2 spikes surface compared to control. However, no such reduction was detected for E. coli. The long-term success of implants relies on establishing and maintaining hard and soft peri-implant tissues. Ti2 spikes represent a novel and promising approach to enhance osseointegration and optimize biocompatibility.
RESUMEN
Plasma treatment on a zirconia surface prevents bacterial contamination and maintains osteoblast activity. To assess the degree of adhesion of Porphyromonas gingivalis on a zirconia surface after non-thermal plasma (NTP) treatment, specimens were treated with plasma for 60, 300, and 600 s, after which P. gingivalis was inoculated onto the surface and incubated for 48 h. To assess osteoblast activity after NTP treatment, osteoblasts (MC3T3-E1) were dispensed onto the specimens contaminated with P. gingivalis immediately after NTP for 60 and 120 s, followed by incubation for 48, 72, and 96 h. P. gingivalis was cultured after 60 s of NTP treatment of zirconia. The NTP and control groups showed no significant difference (p = 0.91), but adhesion was significantly increased following NTP treatment for 300 s or longer (300, 600 s groups) (p < 0.05). After NTP treatment of P. gingivalis-contaminated zirconia, osteoblast activity significantly increased at 72 and 96 h (I60 and I120 s group) in the groups treated with plasma (p < 0.017). Application of NTP to dental zirconia implants for 60 s not only inhibits the proliferation of P. gingivalis, which causes peri-implantitis but also increases osseointegration on zirconia surfaces contaminated with P. gingivalis.
RESUMEN
A novel approach of surface treatment of orthopaedic implants combining electric discharge machining (EDM), chemical milling (etching) and shot peening is presented in this study. Each of the three techniques have been used or proposed to be used as a favourable surface treatment of biomedical titanium alloys. But to our knowledge, the three techniques have not yet been used in combination. Surface morphology and chemistry were studied by scanning electron microscopy and X-ray photoelectron spectroscopy, respectively. Fatigue life of the material was determined and finally several in-vitro biocompatibility tests have been performed. EDM and subsequent chemical milling leads to a significant improvement of osteoblast proliferation and viability thanks to favourable surface morphology and increased oxygen content on the surface. Subsequent shot-peening significantly improves the fatigue endurance of the material. Material after proposed combined surface treatment possesses favourable mechanical properties and enhanced osteoblast proliferation. EDM treatment and EDM with shot peening also supported early osteogenic cell differentiation, manifested by a higher expression of collagen type I. The combined surface treatment is therefore promising for a range of applications in orthopaedics.
Asunto(s)
Proliferación Celular/efectos de los fármacos , Osteoblastos/efectos de los fármacos , Titanio/química , Aleaciones , Materiales Biocompatibles/química , Adhesión Celular/efectos de los fármacos , Diferenciación Celular/efectos de los fármacos , Línea Celular Tumoral , Supervivencia Celular/efectos de los fármacos , Técnica del Anticuerpo Fluorescente , Humanos , Microscopía Electrónica de Rastreo , Osteoblastos/citología , Espectroscopía de Fotoelectrones , Prótesis e Implantes , Propiedades de Superficie , Titanio/farmacologíaRESUMEN
BACKGROUND: Nano-hydroxyapatite particles have better bioactivity than the coarse crystals. So, they can be utilized for engineered tissue implants with improved efficiency over other materials. The development of materials with specific bioactive characteristics is still under investigation. METHODS: The surface properties of four hydroxyapatite materials templated by different micelle-polymer structured network are studied. The synergistic interaction of each block copolymer in contact with CTAB rod-like micelles results in crystalline HAp nano-rods of 25-50nm length organized in hierarchical structures with different micro-rough characteristics. RESULTS: It was observed that the material in vitro bioactivity strongly depends on the surface structure while in a minor extent on their Ca/P ratio. So, MIII and MIV materials with Skewness parameter Rsk>2.62 favored the formation on their surfaces of net-like phase with a high growth kinetic constant; while MI and MII (Rsk≤2.62) induced the appearance of spherulitic-like structures and a growth rate 1.75 times inferior. Material biocompatibility was confirmed by interaction with rat calvarial osteoblasts. CONCLUSIONS: The different structures growth is attributed to a dissimilar matching of crystal planes in the material and the apatite layer formed. In specific synthesis conditions, a biocompatible material with a Ca/P ratio close to that for the trabecular bone and a morphology that are considered essential for bone-bonding was obtained. GENERAL SIGNIFICANCE: The creation of implantable devices with a specific bioactive characteristic may be useful to manipulate the attachment of cells on mineral coating directly affecting the stability and life of the implant.