RESUMEN

Objective: To evaluate tooth displacement and periodontal stress generated by the dual action vertical intra-arch technique (DAVIT) for open-bite correction using three-dimensional finite element analysis. Methods: A three-dimensional model of the maxilla was created by modeling the cortical bone, cancellous bone, periodontal ligament, and teeth from the second molar to the central incisor of a hemiarch. All orthodontic devices were designed using specific software to reproduce their morpho-dimensional characteristics, and their physical properties were determined using Young's modulus and Poisson's coefficient of each material. A linear static simulation was performed to analyze the tooth displacements (mm) and maximum stresses (Mpa) induced in the periodontal ligament by the posterior intrusion and anterior extrusion forces generated by the DAVIT. Results: The first and second molars showed the greatest intrusion, whereas the canines and lateral incisors showed the greatest extrusion displacement. A neutral zone of displacement corresponding to the fulcrum of occlusal plane rotation was observed in the premolar region. Buccal tipping of the molars and lingual tipping of the anterior teeth occurred with intrusion and extrusion, respectively. Posterior intrusion generated compressive stress at the apex of the buccal roots and furcation of the molars, while anterior extrusion generated tensile stress at the apex and apical third of the palatal root surface of the incisors and canines. Conclusions: DAVIT mechanics produced a set of beneficial effects for open-bite correction, including molar intrusion, extrusion and palatal tipping of the anterior teeth, and occlusal plane rotation with posterior teeth uprighting.

RESUMEN

OBJECTIVE: Current standardized in vitro bending experiments for orthodontic archwires cannot capture friction conditions and load sequencing during multi-bracket treatment. This means that clinically relevant forces exerted by superelastic wires cannot be predicted. To address these limitations, this study explored a novel test protocol that estimates clinical load range. METHODS: The correction of a labially displaced maxillary incisor was simulated using an in vitro model with three lingual brackets. Deflection force levels derived from four different protocols were designed to explore the impact of friction and wire load history. These force levels were compared in nickel-titanium (NiTi) archwires with three commonly used diameters. The unloading path varied between protocols, with single or multiple sequences and different load orders and initial conditions. RESULTS: Deflection forces from the new protocol, employing multiple continuous load/unload cycles (CCincr), consistently exceeded those from the conventional protocol using a single continuous unloading path (CUdecr). Mean differences in plateau force ranged from 0.54 N (Ø 0.014" wire) to 1.19 N (Ø 0.016" wire). The CCinr protocol also provided average force range estimates of 0.47 N (Ø 0.012" wire), 0.89 N (Ø 0.014" wire), and 1.15 N (Ø 0.016" wire). SIGNIFICANCE: Clinical orientation towards CUdecr carries a high risk of excessive therapeutic forces because clinical loading situations caused by friction and load history are underestimated. Physiological tooth mobility using NiTi wires contributes decisively to the therapeutic load situation. Therefore, only short unloading sequences starting from the maximum deflection in the load history, as in CCincr, are clinically meaningful.

Asunto(s)

RESUMEN

OBJECTIVES: To synthesise the dentoalveolar, periodontal and skeletal changes that occur when using maxillary expansion techniques assisted by temporary anchorage devices compared to conventional protocols. METHODS: Five databases and grey literature were consulted, up to December 2023, focusing on intervention designs and excluding other type of studies. The quality assessment was conducted by using the adaptation for orthodontics of the CONSORT statement, the guidelines for reporting non-randomised studies, the RoB-2 tool, and the ROBINS-I tool. A descriptive summary and meta-analysis using RevMan 5.4 were performed. RESULTS: Nine clinical trials were included (n=377 patients, mean age 13.2±0.6) with a diagnosis of transverse maxillary deficiency. The analysed studies showed qualitative dentoalveolar and periodontal changes after expansion, which were greater on the maxillary first premolars in tooth-borne appliances. Meta-analyses for some effects were included from two studies (n=64); patients who used tooth-borne appliances had greater effects of buccal intercoronal width between the premolars with statistically significant differences (Std Mean difference 2.34; 95% CI: 0.04-4.65 p=0.05). Conversely, those patients who used bone-borne or hybrid appliances had greater effects of buccal intercoronal width between molars with statistically significant differences (Std Mean difference -0.64; 95% CI: -1.38-0.10; p=0.09). CONCLUSIONS: According to the studies analysed, all measurements increased in the intervention groups after expansion. Quantitative analyses show different findings at dentoalveolar level when tooth-borne, bone-borne or hybrid appliances are considered. Nevertheless, the results should be taken with caution due to the heterogeneity of the studies. The protocol was registered at PROSPERO (CRD42021283170), with no funding to report.

Asunto(s)

RESUMEN

We demonstrate pre-epiglottic baton plate as non-invasive treatment modality for initial airway management in newborns with Pierre Robin Sequence. A case example illustrates management of upper airway obstruction and feeding using digital technology to facilitate customization. Laryngoscope, 2024.

RESUMEN

ABSTRACT Objective: This study aimed to compare the influence of four different maxillary removable orthodontic retainers on speech. Material and Methods: Eligibility criteria for sample selection were: 20-40-year subjects with acceptable occlusion, native speakers of Portuguese. The volunteers (n=21) were divided in four groups randomized with a 1:1:1:1 allocation ratio. The four groups used, in random order, the four types of retainers full-time for 21 days each, with a washout period of 7-days. The removable maxillary retainers were: conventional wraparound, wraparound with an anterior hole, U-shaped wraparound, and thermoplastic retainer. Three volunteers were excluded. The final sample comprised 18 subjects (11 male; 7 female) with mean age of 27.08 years (SD=4.65). The speech evaluation was performed in vocal excerpts recordings made before, immediately after, and 21 days after the installation of each retainer, with auditory-perceptual and acoustic analysis of formant frequencies F1 and F2 of the vowels. Repeated measures ANOVA and Friedman with Tukey tests were used for statistical comparison. Results: Speech changes increased immediately after conventional wraparound and thermoplastic retainer installation, and reduced after 21 days, but not to normal levels. However, this increase was statistically significant only for the wraparound with anterior hole and the thermoplastic retainer. Formant frequencies of vowels were altered at initial time, and the changes remained in conventional, U-shaped and thermoplastic appliances after three weeks. Conclusions: The thermoplastic retainer was more harmful to the speech than wraparound appliances. The conventional and U-shaped retainers interfered less in speech. The three-week period was not sufficient for speech adaptation.

RESUMO Objetivo: Este estudo teve como objetivo comparar a influência na fala causada por quatro diferentes contenções ortodônticas removíveis superiores. Material e Métodos: Os critérios de elegibilidade para seleção da amostra foram: indivíduos com 20 a 40 anos de idade, com oclusão aceitável, falantes nativos de português. Os voluntários (n=21) foram divididos em quatro grupos, randomizados com proporção de alocação de 1:1:1:1. Os quatro grupos utilizaram os quatro tipos de contenção, em ordem aleatória e em período integral por 21 dias cada, com período de wash-out de sete dias. As contenções superiores removíveis foram: wraparound convencional, wraparound com orifício anterior, wraparound em U e contenção termoplástica. Três voluntários foram excluídos. A amostra final foi composta por 18 indivíduos (11 homens; 7 mulheres) com idade média de 27,08 anos (DP=4,65). A avaliação da fala foi realizada em gravações de trechos vocais, realizadas antes, imediatamente após e 21 dias após a instalação de cada contenção, com análise perceptivo-auditiva e acústica das frequências formantes F1 e F2 das vogais. ANOVA de medidas repetidas e teste de Friedman com Tukey foram utilizados para comparação estatística. Resultados: As alterações de fala aumentaram imediatamente após a instalação das contenções wraparound e termoplástica, e reduziram após 21 dias, mas não para níveis normais. Porém, esse aumento foi estatisticamente significativo apenas para as contenções wraparound com orifício anterior e termoplástica. As frequências dos formantes das vogais foram alteradas no momento inicial e, após três semanas, as alterações se mantiveram com as contenções convencional, em forma de U e termoplástica. Conclusões: A contenção termoplástica foi mais prejudicial à fala do que os aparelhos wraparound. Oswraparounds convencional e em forma de U interferiram menos na fala. O período de três semanas não foi suficiente para adaptação da fala.

RESUMEN

Nowadays, many people use clear aligners to address their dental issues. The efficacy of transparent dental aligners must be investigated even though they are more aesthetically pleasing, easy to use, and tidy than permanent tools. Thirty-five patients in this study's sample group who used Nuvola® clear aligners for their orthodontic therapy were prospectively observed. Initial, simulated, and final digital scans were analysed with a digital calliper. The actual results were compared with the prescribed ending position to evaluate the efficacy of transversal dentoalveolar expansion. Aligner treatments in Groups A (12) and B (24), particularly in the dental tip measures, demonstrated high adherence to the prescription. On the other hand, the gingival measures exhibited a greater level of bias, and the differences were statistically significant. However, there was no difference in the outcomes between the two groups (12 vs. 24). Within specific parameters, the evaluated aligners were shown to be helpful in predicting movements in the transverse plane, particularly when considering movements linked to the vestibular-palatal inclination of the dental elements. This article compares the expansion effectiveness of Nuvola® aligners compared with other work in the literature using competitor companies.

RESUMEN

Objective: Infrazygomatic crestal (IZC) implants have gained increased popularity over the past few years. Hardly any studies have been done to assess the rate and reasons for failure of IZCs. This prospective study was planned and designed with the primary objective of assessing the rate of failure of bone-screws (BS) placed in the infrazygomatic crest. In continuation, the secondary objective was to assess the factors that were associated with the failure. Materials and methods: The study was carried out by taking a detailed case history, (age, gender, vertical skeletal pattern, medical history), photographic records, radiographs, and clinical examination of a total of 32 randomly selected. patients of south indian origin who required infrazygomatic implants bilaterally as the choice of anchorage conservation to retract their incisors. All selected subjects were required to take a PA Cephalogram after the implant placement. The age of the patients ranged from 18 to 33 with an average age of 25 years. The patient log was maintained which included the treatment mechanics, status of oral hygiene, stability of implants, time of loading of the implant, presence of inflammation and time of failure of implant. The angulation of implant was measured on a digital PA cephalogram using Nemoceph software. These parameters were examined to evaluate independent and dependent variables using the Chi-Square test and Fischer's exact test. Result: A failure rate 28.1% for IZC placed in the infrazygomatic crest region was observed. Patients with a high mandibular plane angle, poor oral hygiene, immediately loaded implant, peri-implantitis, and severe clinical mobility showed higher failure rates. Variables such as age, gender, sagittal skeletal pattern, length of the implant, type of movement, occluso-gingival position, method of force application, and angle of placement were not significantly associated with implant failure. Conclusion: Oral hygiene and peri-screw inflammation must be controlled to minimize the failure of bone screws placed in the infrazygomatic crest region. Loading of the implant should be done after a latent period of two weeks. A higher failure rate was observed in patients with vertical growth pattern.

RESUMEN

OBJECTIVE: This study was conducted to compare maxillary incisor retraction rates using buccal orthodontics with segmented arch approach supported by a buccal or palatal mini-screw in non-growing Class II Division 1 patients during a 3-month period. PATIENTS AND METHODS: All patients between September 2018 and December 2021 with following criteria were included: non-growing class II division 1 protrusion, indication for premolar extraction, no or little crowding, normal overbite, no previous orthodontic treatment, no systematic disease, good oral hygiene, no periodontal problems or oral habits. Mini-implant was inserted buccally or palatally between upper second premolar and first molar bilaterally. Incisor retraction was manipulated by a 200-gram force through a nickel-titanium closed-coil spring extended from the mini-implant to the segmental design. Study casts were made before retraction and after every 4 weeks (T0: baseline, T1: 4 weeks, T2, 8 weeks, T3: 12 weeks). A repeated measures ANOVA was performed for total comparison of data (mm of retraction) on 3D casts. A pairwise t test with Bonferroni correction was used for comparison between two experimental periods for the same group. An independent samples t-test was also used for comparison between two groups for the same experimental period. RESULTS: Of 30 patients meeting the eligibility criteria, only 28 were included with mean age 16±2.5 years. Repeated measures ANOVA revealed significant differences in incisor retraction between the time intervals for both buccal and palatal groups (P=0.001). In addition, the paired-sample t test indicated a significant difference between each time interval for both the buccal and palatal groups (P=0.001), except between T3 and T2 for the palatal group (P=0.09). The independent sample t-test revealed significant differences between the buccal and palatal groups at T1 (Mean: 0.55 [0.355-0.748],=0.001) and T2 (Mean: 1.4 [0.91-1.88], P=0.001); whereas no significant difference was found at T3 (Mean: 1.15 [0.67-1.63], P=0.945). CONCLUSIONS: Anterior retraction using a segmental palatal model with mini-screws was effective regardless of the buccal or palatal situation of the minivis. Retraction of incisors with palatal miniscrews was significantly faster in the first two months.

Asunto(s)

RESUMEN

No final da década de 70, ocorreu a introdução da tecnologia de desenho assistido por computador e fabricação assistida por computador (CAD/CAM) na Odontologia. As principais proposições dessa tecnologia seriam automatização do processo manual minimizando as variações ou falhas humanas. Dentre os benefícios do produto citado, destacam-se a possibilidade de individualização dos acessórios de acordo com as necessidades biomecânicas do paciente, personalizando a sua prescrição e o formato da sua base para melhor adaptação ao dente, dando ao ortodontista a possibilidade de alcançar finalizações de tratamentos muito mais precisas. A posição do primeiro molar superior tem grande importância para a clínica ortodôntica. As rotações dos primeiros molares superiores estão presentes na maioria das más oclusões, principalmente na má oclusão de Classe II de Angle Divisão 1, que aumenta o espaço ocupado pelos dentes na arcada dentária. O presente estudo avaliou in vitro o desempenho dos tubos no controle rotacional dos molares superiores. Nesta pesquisa, os tubos foram colados em primeiros molares superiores esquerdos artificiais de resina, aleatoriamente, divididos em quatro grupos, de acordo com o tipo de tubo utilizado e posicionamento de colagem. Os seguintes grupos foram testados: Grupo 1: Tubo cerâmico prototipado, colado na posição central; Grupo 2: Tubo cerâmico prototipado, colado na posição distal; Grupo 3: Tubo simples metálico colado na posição central e Grupo 4:Tubo simples metálico colado na posição distal. Para a execução dos testes, hemiarcadas superiores esquerdas contendo desde o dentes incisivo central superior ao segundo molar superior esquerdo foram obtidas por arquivo STL (Standard Triangle Language) através do software americano Autodesk Meshmixer. Os tubos ortodônticos foram fixados por colagem indireta com cianoacrilato na face vestibular dos dentes. Para a avaliação da eficiência dos tubos ortodônticos na correção da rotação do primeiro molar superior foi necessária a utilização de um simulador eletrônico, com o objetivo de padronizar os testes para todas as amostras pesquisadas. Testes T de student e Mann-Whitney foram aplicados para avaliar diferença estatística entre os resultados obtidos nos grupos. Na posição Central, a média dos pulsos de correção dos tubos cerâmicos prototipados (39.41 pulsos) foi superior à média dos tubos metálicos (27.37 pulsos) (teste T de Student p<0.05). Na posição distal, a média dos pulsos de correção dos tubos cerâmicos prototipados (38.38 pulsos) foi superior à média dos tubos metálicos (18.07 pulsos) (teste de Mann-Whitney, p<0.05). Tubos cerâmicos prototipados obtiveram uma maior intensidade da correção da rotação do molar superior que os tubos metálicos, através da metodologia adotada na presente pesquisa, nas duas situações avaliadas. (AU)

At the end of the 1970s, computer-aided design and computer-aided manufacturing (CAD/CAM) technology was introduced into dentistry. The main propositions of this technology would be the automation of the manual process, minimizing human variations or errors. Among the benefits of the product, the possibility of individualizing the accessories according to the patient's biomechanical needs stands out, customizing their prescription and the shape of their base for better adaptation to the tooth, giving the orthodontist the possibility of achieving complete much more accurate treatments. The position of the upper first molar is of great importance for the orthodontic clinic. Rotations of the upper first molars are present in most malocclusions, especially in Angle Class II Division 1 malocclusion, which increases the space occupied by the teeth in the dental arch. The present study evaluated in vitro the performance of the tubes in the rotational control of upper molars. In this research, the tubes were bonding to artificial resin upper left first molars, randomly, divided into four groups, according to the type of tube used and gluing positioning. The following groups were tested: Group 1: Prototyped ceramic tube, bonded in the central position; Group 2: Prototyped ceramic tube, bonded in the distal position; Group 3: Simple metallic tube bonded in the central position and Group 4: Simple metallic tube bonded in the distal position. For the execution of the tests, upper left hemiarchs containing from central incisor teeth superior to the upper left second molar were obtained using an STL (Standard Triangle Language) file using the American software Autodesk Meshmixer. The orthodontic tubes were fixed by indirect bonding with cyanoacrylate on the buccal surface of the teeth. To evaluate the efficiency of orthodontic tubes in correcting the rotation of the upper first molar, it was necessary to use an electronic simulator, with the aim of standardizing the tests for all samples researched. Student's T and Mann-Whitney tests were applied to evaluate statistical differences between the results obtained in the groups. In the Central position, the average correction pulses for the prototyped ceramic tubes (39.41 pulses) were higher than the average for the metallic tubes (27.37 pulses) (Student's T test p<0.05). In the distal position, the average correction pulses for the prototyped ceramic tubes (38.38 pulses) were higher than the average for the metallic tubes (18.07 pulses) (Mann-Whitney test, p<0.05). Prototyped ceramic tubes obtained a greater intensity of correction of upper molar rotation than metallic tubes, through the methodology adopted in the present research, in the two situations evaluated. (AU)

Asunto(s)

RESUMEN

There is a critical need for an accurate device for orthodontists to know the magnitude of forces exerted on the tooth by the orthodontic brackets. Here, we propose a new orthodontic force measurement principle to detect the deformation of the elastic semi-sphere sensor. Specifically, we aimed to detail technical issues and the feasibility of the sensor performance attached to the inner surface of the orthodontic aligner or on the tooth surface. Accurate force tracking is important for the optimal decision of aligner replacement and cost reduction. A finite element (FE) model of the semi-sphere sensor was developed, and the relationship between the force and the contact area change was investigated. The prototype was manufactured, and the force detection performance was experimentally verified. In the experiment, the semi-sphere sensor was manufactured using thermoplastic polymer, and a high-precision mold sized 3 mm in diameter. The change in the contact area in the semi-sphere sensor was captured using a portable microscope. Further development is justified, and future implementation of the proposed sensor would be an array of multiple semi-sphere sensors in different locations for directional orthodontic force detection.

RESUMEN

OBJECTIVES: To evaluate the treatment effects and post-treatment stability of the maxillary total arch distalization using TADs during the non-extraction treatment of class II malocclusions. MATERIALS AND METHODS: Study involved an electronic search followed by hand searching for randomized and non-randomized clinical studies about maxillary total arch distalization using TADs. After data extraction and risk of bias assessment, meta-analysis was performed for dental, skeletal and soft tissue changes using the Generic-inverse variance approach by use of the mean difference and random-effect model. RESULTS: In total, 1788 articles were identified, 88 full texts were screened and 22 studies were found eligible; 17 of them were included in the quantitative analysis. The means of distalization/distal tipping of the maxillary first molar were 4mm/3.17° in adults, 3.95mm/1.61° in adolescents after treatment with the Modified C-Palatal plate (MCPP), while they were 2.44mm/2.91° with the inter-radicular mini-screws. Both MCPP's treatment in adults and inter-radicular mini-screws resulted in significant intrusion of U6 (1.64 and 0.75mm, respectively), while insignificant extrusion of U6 was resulted in adolescents treated by MCPP. MCPP appliances resulted in palatal inclination/extrusion of maxillary incisors U1 (6.77°/2mm in adults, 7.46°/3.14mm in adolescents). In contrast, inter-radicular mini-screws resulted in less palatal less amount of palatal inclination/insignificant intrusion of U1 (2.42°/0.14mm). MCPP treatment also resulted in significant changes in the skeletal measurements (SNA, ANB, occlusal and mandibular planes). Insignificant differences were found between subgroups in the retraction amount of maxillary incisors, as well as the upper and lower lips. In the follow-up of adolescents treated with MCPP, a significant amount of mesial movement, mesial tipping, and extrusion (2.94mm, 2.84°, and 3.94mm, respectively) was found. However, skeletal and occlusal corrections of the Class II relationship were maintained. CONCLUSIONS: Maxillary total arch distalization using TADs can be an effective and stable treatment procedure. However, RCTs or prospective cohort studies are highly recommended to establish a clinical evidence regarding their efficiency.

Asunto(s)

RESUMEN

OBJECTIVE: The aim of this case series was to test various personalized, CAD/CAM-manufactured orthodontic extrusion appliances. The appliances were characterized by high rigidity and manufacturing precision. In addition, the orthodontic force vector could be precisely and three-dimensionally planned. METHOD AND MATERIALS: After a comprehensive diagnosis of three patients with deep fractured teeth by an interdisciplinary team, each patient's personalized extrusion protocol was determined (slow or rapid extrusion). Based on an intraoral scan, the personalized extrusion appliances were then digitally planned and manufactured using selective laser melting. The force vector was also precisely planned during this process. The appliances were inserted, and the force on the teeth to be extruded was precisely applied in accordance with the extrusion protocol. After extrusion, the teeth were retained and, if necessary, permanently restored. RESULTS: The target teeth of all three patients were successfully extruded. Furthermore, good cleanability and high wearing comfort of the appliances were maintained throughout treatment, as was the precise application of force. CONCLUSION: The effectiveness of the tested digital workflow for precise and simplified orthodontic extrusion was clinically proven. The workflow guaranteed the following throughout treatment: precise planning and application of the force system; improved periodontal hygiene; and improved wearing comfort of the appliance, without affecting the patient's existing occlusion.

Asunto(s)

RESUMEN

O objetivo da pesquisa foi avaliar a preferência de jovens universitários de cursos das áreas da Saúde, Exatas e Humanas por diferentes modelos de aparelho ortodôntico. Foram selecionados dois (modelos) indivíduos jovens, um masculino e um feminino. Em seguida, foram confeccionadas 6 imagens simulando aparelhos ortodônticos para cada modelo. Após confeccionar um álbum de fotografias com todas as imagens, os álbuns foram entregues aos estudantes universitários (n=169) com idades entre 18 a 25 anos, juntamente com um questionário. Foram então formados 3 grupos de avaliadores das áreas do conhecimento, Saúde (n=62), Exatas (n=51) e Humanas (n=56). No questionário, os avaliadores identificaram o aparelho de sua preferência, caso fossem ser tratados, apontando nas 6 imagens a ordem de sua preferência. Eles ainda responderam o motivo da escolha daquele modelo de aparelho. Os alinhadores obtiveram maiores avaliações sobre os aparelhos estéticos (5,0). Em contrapartida, os aparelhos metálicos foram os piores avaliados (2,0). Não houve influência da área de estudo e do gênero do avaliador sobre a hierarquia de atratividade na avaliação, no entanto as avaliadoras do sexo feminino da área de Saúde foram mais críticas quanto ao aparelho metálico com ligadura azul. Apesar da área de estudo não ter influenciado na preferência pelo tipo de aparelho, sendo os mais estéticos preferidos sobre os metálicos, as avaliações mais críticas partiram dos estudantes da área de Saúde. (AU)

The aim of the present research was to evaluate the preference of young university students from courses of the health, science, and human areas regarding different orthodontic appliance design. Two (models) young individuals were selected, one male and one female. Then 6 images were made simulating orthodontic appliances for each model. After producing a photo album with all the images, the albums have been given to university students (n=169) aged between 18 and 25 years old, along with a questionnaire. Three groups of evaluators from different areas of knowledge: Health (n=62), Science (n=51) an Human area (n=56) were formed. In the questionnaire, the evaluators identified which device they would prefer if they were treated, indicating the order of their preference on the 6 images. They also answered the reason for choosing that device model. Aligners had higher ratings than aesthetic devices (5.0). On the other hand, metallic appliances were the worst evaluated (2.0). There was no influence of the study area and the evaluator's gender on the hierarchy of attractiveness in the evaluation, however female evaluators from the Health area were more critical regarding metallic braces with blue ligature. Although the study area did not influence the preference for the type of appliance, with the most aesthetic being preferred over metallic ones, the most critical evaluations came from students in the Health area (AU)

Asunto(s)

RESUMEN

AIM: To test the null hypothesis that there was no difference in treatment efficiency between therapies undertaken with conventional (CBs), passive self-ligating (PSLBs) or active self-ligating (ASLBs) brackets. MATERIALS AND METHODS: An electronic search was performed in 3 data bases (Pubmed, Web of Science, Cochrane Library) from their origin up to January 2019. Additional references were hand searched. Search was strictly restricted to randomized controlled trials (RCTs) and split-mouth design studies (SMDs). RCTs and SMDs were initially processed separately and subsequently combined in a network meta-analysis. The following variables were evaluated: treatment duration, number of visits, occlusal outcomes, alignment rate, transverse arch dimensional changes, incisor position modification, rate of space closure, anchorage loss, bond failure, root resorption, perception of discomfort during the initial phase of alignment, time to ligate in or to untie an archwire, periodontal variables, quality of life. RESULTS: On 229 papers, 30 RCTs and 9 SMDs were finally included in this study. Out of 85 comparisons, 16 only revealed statistically significant differences. It was quicker to untie and ligate an 0.014 NiTi arch from/in 6 ASLBs anterior ceramic brackets compared to 6 ceramic CBs. It was also more painful to insert and remove an 0.019×0.025 SS wire in/from PSLB's brackets compared to CB's attachments. Compared to conventional brackets, there was less maxillary incisor proclination with PSLBs in non-extraction cases. Moreover, there was less bleeding on probing 4-5 weeks after bonding with PSLBs compared to CBs brackets. The only significant difference between ASLBs and PSLBs was that alignment was 10 days faster with active self-ligating braces compared with passive self-ligating braces even if treatment duration between ASLBs and PSLBs was not significantly different. The network meta-analysis revealed that IMPA was greater in extractions cases with CBs compared with both ASLBs (+2,5°) and PSLBs (+1,6°). CONCLUSIONS: The vast majority of the studied variables did not show any significant differences between the three types of brackets. The most significant findings were that it was quicker to insert and remove archwires from ASLBs compared to CBs, and it was more painful to insert and remove an 0.019×0.025" stainless steel wire in/from PSLBs compared to CBs. The major difference between ASLBs and PSLBs was that alignment was 10 days faster with active self-ligating braces compared with passive self-ligating braces even if treatment duration between ASLBs and PSLBs was not significantly different. Most of the claims put forward by the suppliers were not substantiated by our network meta-analysis.

Asunto(s)

RESUMEN

OBJECTIVES: To discern the effects of computer-aided design (CAD)/computer-aided manufactured (CAM) customized appliances and piezocision on orthodontic treatment (OT). MATERIALS AND METHODS: The study combined findings from two previously published randomized controlled trials: (1) standard OT vs piezocision-assisted standard OT, and (2) CAD/CAM OT vs piezocision-assisted CAD/CAM OT. Piezocision is a minimally invasive corticotomy surgical procedure used to accelerate orthodontic treatment and CAD/CAM refers to CAD/CAM customized brackets and archwires. The outcomes were the overall treatment time, and the durations of the alignment phase and fine-tuning phase. Clinical and radiological features also were evaluated. RESULTS: The combined study included 48 patients with similar baseline characteristics. Compared to the standard treatment, CAD/CAM technology alone significantly decreased the overall median OT time from 543 to 394 days (P < .001) and from 543 to 254 days (P < .0001) when combined with piezocision. Although piezocision significantly reduced the duration of the alignment phase in the mandible and maxilla, CAD/CAM technology considerably shortened the fine-tuning phase. All periodontal and radiographic parameters remained stable from the start to the end of treatment in all groups. CONCLUSIONS: CAD/CAM technology combined with piezocision accelerates the entire OT process, during the alignment phase for piezocision and during the fine-tuning phase for CAD/CAM, with a global reduction of the overall treatment time of more than 50%.

Asunto(s)

RESUMEN

OBJECTIVE: To assess the influence of changing the size and position of lever arm on transverse and vertical bowing effects during retraction in lingual biomechanics. METHODS: A three dimensional 3D finite element method was used to simulate en masse anterior teeth retraction using lingual appliance with sliding mechanics. Two groups were made, 1st group had lever arm mesial to canine while 2nd group had distal to canine. Each group had 4 subgroups with lever arm height varying from 0mm to 12mm. Displacements of the maxillary anterior teeth were noted in each group. RESULTS: As the Lever Arm Height (LAH) increased in group I, the vertical bowing effect reduced while the transverse bowing increased with respect to canines. In group II, both vertical and transverse bowing effects increased but transverse bowing was less as compared to group I. CONCLUSION: Strategic location of the lever arm is required in different clinical situations during en-mass retraction, keeping in mind the location of Centre of Resistance (CRes) as well as the vertical and the transverse bowing effects.

Asunto(s)

RESUMEN

OBJECTIVE: Some modifications of orthodontic appliances such as the rapid maxillary expansion (RME) device with a Hyrax screw or Herbst are fabricated using traditional investment casting (lost-wax casting). This is precise but very labor-intensive. New technologies enable us today to use direct selective laser sintering (SLS) to produce freeform metallic structures. These machines are very expensive and only available in specialized laboratories. The aim of this investigation was to combine fused filament fabrication (FFF) 3D printing with wax-based filaments to produce orthodontic appliances via investment casting. METHOD AND MATERIALS: For demonstration purposes, a lingual arch, a palatal arch, and an RME appliance were digitally designed based on an intraoral scan. The *.stl files were sliced and printed with a dual-nozzle FFF printer. The object was printed with a wax-based filament especially suited for investment casting, and support structures were printed with water-soluble polyvinyl-alcohol (PVA) filament. The printed objects were cast in metal and finished. RESULTS: All appliances were successfully cast and polished. They were provisionally placed intraorally. The fit was clinically very good and comparable to traditionally crafted appliances. The printing and handling of the parts made of these special filaments is challenging. CONCLUSION: With this experiment, the successful production of investment casting using FFF printing was shown for the first time.

Asunto(s)

RESUMEN

Clear aligners are the fastest-growing appliances in this century, which are not only favored by patients, but also concerned by doctors. This article explains the significance of vertical control in orthodontic treatment, the advantages and disadvantages of vertical control with clear aligner. It also analyzes the causes of the shortcomings and how to use existing technologies and methods to make up for these shortcomings.

Asunto(s)

RESUMEN

INTRODUÇÃO: Os aparelhos intraorais (AIO) possuem indicação para tratamento da Síndrome da Apneia Obstrutiva do Sono (SAOS) inclusive em pacientes com baixa adesão ao CPAP. A polissonografia com o AIO pode confirmar benefício terapêutico. MÉTODOS: Compararam-se os resultados polissonográficos de um AIO semiflexível em pacientes sob uso inadequado do CPAP por meio de estudo-piloto retrospectivo, incluindo 17 pacientes (11 homens e 6 mulheres) com 53,7 +- 7,8 anos, IMC de 27,5 +- 4,1kg/m2 e índice de apneia- -hipopneia basal (IAH) de 35,0 +- 19,8/h. Confirmados o uso inadequado ou recusa do CPAP, os pacientes receberam um aparelho com propulsão semiflexível (A-QUALITY) e, após titulação completa, novas polissonografias foram comparadas aos registros basais e com CPAP. Utilizou-se ANOVA para medidas repetidas e post-hoc Bonferroni (p < 0,05). RESULTADOS: Houve redução semelhante no IAH com AIO (7,7 +- 1,7/h) e CPAP (6,1 +- 1,6/h), ambos comparados ao basal (p < 0,001). O índice de dessaturação de O2 foi reduzido com AIO (2,4 +- 0,6/h) e CPAP (1,3 +- 0,6/h), ambos comparados ao basal (15,7 +- 3,8), (p <0,001). O índice de despertares também foi minimizado com AIO (7,2 +- 1,9/h) e CPAP (4,2 +- 0,7/h), ambos comparados ao basal (18,9 +- 5,3), (p<0,001). A eficiência do sono foi maior com o AIO comparado ao CPAP (87,2 +- 2,1 x 75,6 +- 3,9) (p<0,05). CONCLUSÃO: O tratamento com o aparelho selecionado resultou em melhora nos registros polissonográficos nessa amostra e pode ser indicado como alternativa ao CPAP em pacientes subtratados (AU)

INTRODUCTION: Intraoral appliances (IOA) are indicated for treatment of Obstructive Sleep Apnea Syndrome (OSAS) even in patients with poor adherence to CPAP. Polysomnography with IOA may confirm therapeutic benefit. METHODS: Polysomnographic results of a semiflexible IOA in patients under inadequate use of CPAP were compared by a retrospective pilot study including 17 patients (11 men and 6 women) aged 53.7 +- 7.8 years, BMI of 27.05 +- 4.1kg/m2 and basal apnea-hypopnea index (AHI) of 35.0 +- 19.8/h. Confirmed the inappropriate use or refusal of CPAP, the patients received a semiflexible propulsion device (AQUALITY) and, after complete titration, new polysomnographies were compared to baseline and CPAP registers. ANOVA was used for repeated and post-hoc Bonferroni measurements (p <0.05). RESULTS: There was a similar reduction in AHI with OA (7.7 +- 1.7/h) and CPAP (6.1 +- 1.6/h), both compared to baseline (p <0.001). The O2 desaturation index was reduced with IOA (2.4 +- 0.6 h) and CPAP (1.3 +- 0.6/h), both compared to baseline (15.7 +- 3.8) (p <0.001). Awakening rates were also minimized with IOA (7.2 +- 1.9/h) and CPAP (4.2 +- 0.7/h), both compared to baseline (18.9 +- 5.3) (p <0.001). Sleep efficiency was higher with IOA compared to CPAP (87,2 +- 2,1 x 75,6 +- 3,9) (p <0.05). CONCLUSION: Treatment with the selected device resulted in improved polysomnographic records in this sample and may be indicated as an alternative to CPAP in undertreated patients. (AU)

Asunto(s)

RESUMEN

Este estudo teve como objetivo avaliar a capacidade de retenção que os attachments proporcionam aos alinhadores ortodônticos, bem como analisar a reprodutibilidade dos attachments a partir do planejamento digital até a sua reprodução clínica. A amostra foi composta por dezesseis modelos, divididos em 2 grupos, sendo oito no grupo controle impresso (GCI), onde os attachments eram impressos no modelo e outros oito modelos no grupo experimental de resina (GER), cujos attachments foram colados manualmente a partir de uma guia de transferência. Cada grupo foi dividido em outros 4 subgrupos, de acordo com o posicionamento dos attachments em determinados dentes e orientação do tal acessório no formato retangular: canino a 2º pré-molar horizontal (HPM), canino a 1º molar horizontal (HM), canino a 2º pré-molar vertical (VPM) e canino a 1º molar vertical (VM). Placas de PETG foram termoformados para um total de 80 alinhadores, sendo 40 para o grupo GCI e outros 40 para o grupo GER nas espessuras de 0.6 mm e 0.8 mm. Os modelos dos grupos GCI e GER foram escaneados e analisados por comparação digital para avaliação da morfologia dos attachments. Em seguida, os alinhadores foram submetidos a ensaio mecânico de tração. A análise qualitativa mostrou que as bases dos attachments colados possuem excesso de resina, dificultando a criação de ângulos vivos. Ao analisar qualitativamente a morfologia do grupo GER foi possível verificar que os attachments colados tiveram suas bases em dimensões maiores que o planejado. O grupo GER apresentou melhores retenções que os grupo GCI. Não há diferença estatística na orientação do acessório e no número de dentes que possuem os dispositivos. Entretanto, há diferença estatística quanto à espessura de PETG onde as placas de 0.8 mm forneceram maior retenção. Neste caso, os attachments horizontais com colagem até os molares apresentam a maior média de retenção estatisticamente significante (p < 0.01) quando comparados aos outros attachments no grupo experimental. Conclui-se que as placas de 0.8 mm conferem retenção superior do que as de espessura 0.6 mm, e também que a combinação de attachments na horizontal com colagem de canino a molar proporcionam maior retenção quando comparados à outra orientação e ao número de dentes envolvidos. (AU)

This study aimed to evaluate the retention capacity that attachments provide to orthodontic aligners, as well as to analyze the reproducibility of attachments made from guides made for this purpose. The sample consisted on sixteen models which were divided into 2 groups, eight in the printed control group (PCG), whose attachments were printed onto the model and eight in the experimental resin group (ERG), whose attachments were bonded manually from transfer guide. Each group was subdivided into 4, according to the positioning and orientation of the attachments: horizontal premolar (HPM), horizontal molar (HM), vertical premolar (VPM) and vertical molar (VM). PETG acetate aligners were thermoformed for a total of 80 aligners, 40 for the PCG group and another 40 for the ERG group in thicknesses of 0.6 mm and 0.8 mm. The models of the PCG and ERG groups were scanned and analyzed by digital comparison to assess the morphology of the attachments. Then, the aligners were subjected to mechanical tensile testing. The qualitative analysis showed that the bases of the bonded attachments have excess resin, making it difficult to create sharp angles. When analyzing the morphology of the ERG group, it was possible to verify they had the bases in larger dimensions than planned. The ERG group had better retentions than the PCG group. There is no statistical difference in the orientation of the accessory and in the number of teeth that the devices have when the attachments are grouped. However, a statistical difference occurs regarding the observed thickness of acetate whose 0.8 mm aligners provided greater retention. In this case, the horizontal attachments with bonding up to the molars have the highest statistically significant retention average (p <0.01) when compared to the other attachments in the experimental group. It is concluded that the 0.8 mm aligners provide superior retention than those of 0.6 mm thickness, and also that the combination of horizontal attachments with molar canine bonding provides greater retention when compared to the other orientation and the number of teeth involved. (AU)

Asunto(s)