RESUMEN

The literature presents insufficient data evaluating the displacement and micromotion effects resulting from the combined use of tooth-implant connections in fixed partial dentures. Analyzing the biomechanical behavior of tooth-implant fixed partial denture (FPD) prothesis is vital for achieving an optimum design and successful clinical implementation. The objective of this study was to determine the relative significance of connector design on the displacement and micromotion of tooth-implant-supported fixed dental prostheses under occlusal vertical loading. A unilateral Kennedy class I mandibular model was created using a 3D reconstruction from CT scan data. Eight simulated designs of tooth-implant fixed partial dentures (FPDs) were split into two groups: Group A with rigid connectors and Group B with non-rigid connectors. The models were subjected to a uniform vertical load of 100 N. Displacement, strain, and stress were computed using finite element analysis. The materials were defined as isotropic, homogeneous, and exhibiting linear elastic properties. This study focused on assessing the maximum displacement in various components, including the bridge, mandible, dentin, cementum, periodontal ligament (PDL), and implant. Displacement values were predominantly higher in Group B (non-rigid) compared to Group A (rigid) in all measured components of the tooth-implant FPDs. Accordingly, a statistically significant difference was observed between the two groups at the FPD bridge (p value = 0.021 *), mandible (p value = 0.021 *), dentin (p value = 0.043 *), cementum (p value = 0.043 *), and PDL (p value = 0.043 *). Meanwhile, there was an insignificant increase in displacement values recorded in the distal implant (p value = 0.083). This study highlighted the importance of connector design in the overall stability and performance of the prosthesis. Notably, the 4.7 mm × 10 mm implant in Group B showed a displacement nearly 92 times higher than its rigid counterpart in Group A. Overall, the 5.7 mm × 10 mm combination of implant length and diameter showcased the best performance in both groups. The findings demonstrate that wider implants with a proportional length offer greater resistance to displacement forces. In addition, the use of rigid connection design provides superior biomechanical performance in tooth-implant fixed partial dentures and reduces the risk of micromotion with its associated complications such as ligament overstretching and implant overload, achieving predictable prognosis and enhancing the stability of the protheses.

RESUMEN

Improper osteotomy during total knee arthroplasty (TKA) can lead to anterior femoral notching, which increases the risk of periprosthetic fractures due to stress concentration. One potential solution is the addition of an intramedullary stem to the femoral component. However, the optimal stem length remains unclear. In this study, we aimed to determine the optimal stem length using finite element models. Finite element models of femurs were developed with unstemmed prostheses and prostheses with stem lengths of 50, 75, and 100 mm. Under squat loading conditions, the von Mises stress at the notch and stress distribution on four transversal sections of the femur were analyzed. Additionally, micromotion of the prosthesis-bone interface was evaluated to assess initial stability. The unstemmed prosthesis exhibited a von Mises stress of 191.8 MPa at the notch, which decreased to 43.1, 8.8, and 23.5 MPa for stem lengths of 50, 75, and 100 mm, respectively. The stress reduction on four selected femoral transversal sections compared with the unstemmed prosthesis was 40.0%, 84.4%, and 67.1% for stem lengths of 50, 75, and 100 mm, respectively. Micromotion analysis showed a maximum of 118.8 µm for the unstemmed prosthesis, which decreased significantly with the application of stems, particularly at the anterior flange. Intramedullary stems effectively reduced stress concentration at the femoral notch. The 50-mm stem length provided the optimal combination of reduced notch stress, minimized stress-shielding effect, and decreased micromotion at the anterior flange.

RESUMEN

The conical stem tibial design of total ankle replacement (TAR) has high implant-bone micromotion. This may lead to aseptic loosening which can be avoided by improving the tibial design. The objective was to propose the best stem design parameters to reduce implant-bone micromotion along with minimizing stress shielding using an integrated Finite Element-Multi Criteria Decision Making (FE-MCDM) approach. FE models of implanted tibia bones were prepared by changing the height of the stem, the diameter of the stem, and the slant of the stem. Weighted Aggregated Sum Product Assessment (WASPAS), Technique for Order of Preference by Similarities to Ideal Solution (TOPSIS), Evaluation based on Distance from Average Solution (EDAS), and VIseKriterijumska Optimizacija I Kompromisno Resenje (VIKOR) MCDM techniques with equal weights for micromotion and stress shielding were considered. The micromotion and stress shielding were greater when the height of the stem was increased. Whereas, the increase in diameter and slant affected them marginally. The best-performing design was the Model with stem height 6 mm (diameter 6.4 mm and slant 4°) and after that was the Model with stem height 8 mm (diameter 6.4 mm and slant 4°), and then the Model with stem height 10 mm (diameter 6.4 mm and slant 4°). The height of the stem is the most important stem design parameter. Shorter height, moderate thickness, and moderate slanting stem designs are recommended.

RESUMEN

The risk of aseptic loosening in cementless hip stems can be reduced by improving osseointegration with osteoinductive coatings favoring long-term implant stability. Osseointegration is usually evaluated in vivo studies, which, however, do not reproduce the mechanically driven adaptation process. This study aims to develop an in silico model to predict implant osseointegration and the effect of induced micromotion on long-term stability, including a calibration of the material osteoinductivity with conventional in vivo studies. A Finite Element model of the tibia implanted with pins was generated, exploiting bone-to-implant contact measures of cylindrical titanium alloys implanted in rabbits' tibiae. The evolution of the contact status between bone and implant was modeled using a finite state machine, which updated the contact state at each iteration based on relative micromotion, shear and tensile stresses, and bone-to-implant distance. The model was calibrated with in vivo data by identifying the maximum bridgeable gap. Afterward, a push-out test was simulated to predict the axial load that caused the macroscopic mobilization of the pin. The bone-implant bridgeable gap ranged between 50 µm and 80 µm. Predicted push-out strength ranged from 19 N to 21 N (5.4 MPa-3.4 MPa) depending on final bone-to-implant contact. Push-out strength agrees with experimental measurements from a previous animal study (4 ± 1 MPa), carried out using the same implant material, coated, or uncoated. This method can partially replace in vivo studies and predict the long-term stability of cementless hip stems.

RESUMEN

BACKGROUND: Augmented baseplates can be effective at addressing eccentric glenoid wear in reverse total shoulder arthroplasty (rTSA). However, these implants often come in a limited number of predetermined shapes that require additional reaming to ensure adequate glenoid seating. This typically involves complex instrumentation and can have a negative impact on implant stability. Modular baseplate augmentation based on intra-operative measurements may allow for more precise defect filling while preserving glenoid bone. The purpose of this investigation was to assess the stability of a novel ringed baseplate with modular augmentation in comparison to non-augmented standard and ringed baseplate designs. METHODS: In this biomechanical study, baseplate micromotion was tested for three constructs according to American Society for Testing and Materials (ASTM) guidelines. The constructs included a non-augmented curved baseplate, a non-augmented ringed baseplate and ringed baseplate with an 8 mm locking modular augmentation peg. The non-augmented constructs were mounted flush onto polyurethane (PU) foam blocks, while the augmented baseplate was mounted on a PU block with a simulated defect. Baseplate displacement was measured prior to and after 100,000 cycles of cyclic loading. RESULTS: Prior to cyclic loading, the non-augmented and augmented ringed baseplates both demonstrated significantly less micromotion than the non-augmented curved baseplate design (81.1 µm vs 97.2 µm vs 152.7 µm; p=0.009). After cyclic loading, both ringed constructs continued to have significantly less micromotion compared to the curved design (105.5 µm vs 103.2 µm vs 136.6 µm; p<0.001). The micromotion for both ringed constructs remained below the minimum threshold required for bony ingrowth (150 µm) at all time points. CONCLUSION: In the setting of a simulated glenoid defect, locked modular augmentation of a ringed baseplate does not result in increased baseplate micromotion when compared to full contact, non-augmented baseplates. This design offers a simple method for tailored baseplate augmentation that can match specific variations in glenoid anatomy, limiting the need for excessive reaming and ultimately optimizing the environment for long term implant stability. LEVEL OF EVIDENCE: Basic Science Study; Biomechanics.

RESUMEN

The electric cell-substrate impedance sensing (ECIS) is a well-established technique that allows for the real-time monitoring of cell cultures growing on gold-electrodes embedded in culture dishes. Its foundation lays on the insulating effect that cells present against the free-flow of electrons, as these passive electrical properties generate a characteristic complex impedance spectrum when a small-amplitude, non-invasive alternating current (AC) is provided through the electrodes, the living cells, and the culture media in the culture ware. In addition, it possesses the ability to create a wound that is highly confined to the electrode area by simply increasing the amplitude of the AC current in dependence of the pre-resistor strength for a defined pulse duration and at a specific frequency. Therefore, it represents a controlled and reproducible tool to carry out in vitro wound healing experiments. Accordingly, in this methods protocol, the use of the ECIS will be described in the context of the wound healing research: cardiac 3T3 fibroblasts will be wounded and their recovery dynamics analyzed based on the typical methodologies applied to the processing of ECIS data. In addition, cellular micromotions will be evaluated. Finally, fluorescence immunostaining of ECIS samples will be described in order to showcase the potential of the ECIS in combination with other well-established techniques to add further knowledge depth to the understanding of the complex wound healing dynamics.

Asunto(s)

RESUMEN

Aseptic loosening is the primary cause of failure following posterior-stabilized total knee arthroplasty. It is unclear whether tibial post loading of posterior-stabilized prosthesis increases the risk of aseptic loosening of the tibial prosthesis. The purpose of this study is to investigate the biomechanical effects of tibial post loading on the tibial prosthesis fixation interface during level walking, squatting, stair descent, and standing up-sitting down activities. In this paper, finite element models with and without post were established to compare the effects of tibial post loading on the von Mises stress of the proximal tibia, shear stress of the cement, and the bone-prosthesis interface micromotion during four physiological activities. The tibial post loading had an insignificant influence on tibial biomechanics and bone-prosthesis interface micromotion during leveling walking activity. However, compared to the insert without post condition, tibial post loading significantly increased the maximum tibial von Mises stress, the maximum shear stress in the medial of cement, and the bone-prosthesis interface peak micromotion by 912.84%, 612.77%, and 921.09%, respectively, at the moment of the maximum flexion angle for the stair descent activity, and 637.92%, 351.43%, and 519.13%, respectively, at the moment of the maximum flexion angle for the standing up-sitting down activity. Tibial post loading increased the risk of postoperative aseptic loosening of tibial prosthesis in patients with posterior-stabilized total knee arthroplasty, and it was recommended that the post-cam contact mechanism of posterior-stabilized prosthesis should be optimized to reduce the biomechanical impact of tibial post loading on tibial prosthesis fixation.

RESUMEN

Non-cooperative targets, such as birds and unmanned aerial vehicles (UAVs), are typical low-altitude, slow, and small (LSS) targets with low observability. Radar observations in such scenarios are often complicated by strong motion clutter originating from sources like airplanes and cars. Hence, distinguishing between birds and UAVs in environments with strong motion clutter is crucial for improving target monitoring performance and ensuring flight safety. To address the impact of strong motion clutter on discriminating between UAVs and birds, we propose a frequency correlation dual-SVD (singular value decomposition) reconstruction method. This method exploits the strong power and spectral correlation characteristics of motion clutter, contrasted with the weak scattering characteristics of bird and UAV targets, to effectively suppress clutter. Unlike traditional clutter suppression methods based on SVD, our method avoids residual clutter or target loss while preserving the micro-motion characteristics of the targets. Based on the distinct micro-motion characteristics of birds and UAVs, we extract two key features: the sum of normalized large eigenvalues of the target's micro-motion component and the energy entropy of the time-frequency spectrum of the radar echoes. Subsequently, the kernel fuzzy c-means algorithm is applied to classify bird and UAV targets. The effectiveness of our proposed method is validated through results using both simulation and experimental data.

RESUMEN

INTRODUCTION: Several internal fixation devices are available for treating Pauwels type I, II and III femoral neck fractures. The present study compared various fixation implants for all Pauwels fracture types using a CT-based subject-specific finite element model of the femur and determined the most effective implant for each fracture type. MATERIALS AND METHODS: The analysis included four different configurations of cannulated screw models, Femoral Neck System, Dynamic Hip Screw and Dynamic Condylar Screw (with and without anti-rotational screw). Ti-alloy was considered as the implant material. Heterogeneous bone material property was assigned based on CT grey value. Frictional contact was assumed in the contact interfaces. Peak loading corresponding to normal walking and stair-climbing were considered. Equivalent strain in bone, equivalent stress in the implants, femoral head deformation and rotation, micromotion in the contact interfaces, and strain-shielding in bone were evaluated for each implanted model. RESULTS: Stresses generated in the implants were within the yield limit of the implant material. In Pauwels I and II, the micromotion predicted at the contact regions in all the implanted models was within 100 µm, which is suitable for bone integration. However, in Pauwels III fracture, most of the implanted models other than DHS with AR-screw model exhibited micromotion of more than 150 µm in the contact regions, which is expected to inhibit bone growth. CONCLUSIONS: The DHS with AR-screw implanted model was identified as the most effective in treating Pauwels I and III fractures. However, for Pauwels type II, DCS with an AR-screw implant was deemed superior to the other configurations.

Asunto(s)

RESUMEN

Background: Stemless humeral components are being clinically investigated for reverse shoulder arthroplasty (RSA) procedures. There is, however, a paucity of basic science literature on the surgical parameters that influence the success of these procedures. Therefore, this cadaveric biomechanical study evaluated the neck shaft angle (NSA) of implantation on the survivability and performance of stemless RSA humeral components during cyclical loading. Methods: Twelve paired cadaveric humeri were implanted with stemless RSA humeral components at NSAs of 135° and 145°. Implant-bone motion at the periphery of the implant was measured with 3 optical machine vision USB3 cameras outfitted with c-mount premium lenses and quantified with ProAnalyst software. A custom 3-dimensional loading apparatus was used to cyclically apply 3 loading directions representative of physiological states at 5 progressively increasing loading magnitudes. Stemless 135° and 145° implants were compared based on the maximum implant-bone relative distraction detected, as well as the survivorship of the implants throughout the loading protocol. Results: Primary fixation and implant biomechanical survivorship were substantially better in the 145° NSA implants. The 135° NSA implants elicited significantly higher implant-bone distractions during cyclical loading (P = .001), and implant survivorship was considerably lower in the 135° NSA specimens when compared to the 145° NSA specimens (135° NSA: 0%, 145° NSA: 50%) (P < .001). Conclusion: NSA is a modifiable parameter that influences time-zero implant stability, as well as the early survivorship of the stemless RSA humeral components tested in this study. NSA resections of 145° appear to promote better stability than those utilizing 135° NSAs during early postoperative eccentric loads. Further studies are required to assess if other stemless reversed humeral implant designs have improved time-zero fixation at higher NSAs.

RESUMEN

Background: Several studies have reported proximal bone resorption in stemless and press-fit short-stem humeral implants for anatomic total shoulder arthroplasty. The purpose of this biomechanical study was to evaluate implant and cortical bone micromotion of a cortical rim-supported stemless implant compared to a press-fit short stem implant during cyclic loading and static compression testing. Methods: Thirty cadaveric humeri were assigned to 3 groups based on a previously performed density analysis, adopting the metaphyseal and epiphyseal and inferior supporting bone densities for multivariate analyses. Implant fixation was performed in stemless implant in low bone density (SL-L, n = 10) or short stem implant in low bone density (Stem-L, n = 10) and in stemless implant in high bone density (SL-H, n = 10). Cyclic loading with 220 N, 520 N, and 820 N over 1000 cycles at 1.5 Hz was performed with a constant valley load of 25 N. Optical recording allowed for spatial implant tracking and quantification of cortical bone deformations in the medial calcar bone region. Implant micromotion was measured as rotational and translational displacement. Load-to-failure testing was performed at a rate of 1.5 mm/s with ultimate load and stiffness measured. Results: The SL-H group demonstrated significantly reduced implant micromotion compared to both low-density groups (SL-L: P = .014; Stem-L: P = .031). The Stem-L group showed significantly reduced rotational motion and variance in the test results at the 820-N load level compared to the SL-L group (equal variance: P = .012). Implant micromotion and reversible bone deformation were significantly affected by increasing load (P < .001), metaphyseal cancellous (P = .023, P = .013), and inferior supporting bone density (P = .016, P = .023). Absolute cortical bone deformation was significantly increased with stemless implants in lower densities and percentage reversible bone deformation was significantly higher for the SL-H group (21 ± 7%) compared to the Stem-L group (12 ± 6%, P = .017). Conclusion: A cortical rim-supported stemless implant maintained proximally improved dynamic bone loading in variable bone densities compared to a press-fit short stem implant. Biomechanical time-zero implant micromotion in lower bone densities was comparable between short stem and stemless implants at rehabilitation load levels (220 N, 520 N), but with higher cyclic stability and reduced variability for stemmed implantation at daily peak loads (820 N).

RESUMEN

PURPOSE: Cervical disc arthroplasty (CDA) is widely employed for patients diagnosed with cervical degenerative disc disease (CDDD). Postoperative bone loss (BL) represents a radiological alteration that is a relatively novel consideration in the realm of CDA. This study endeavors to examine the risk factors associated with BL following CDA, aiming to elucidate the underlying mechanisms and the impact of BL on surgical outcomes. METHODS: A retrospective study was undertaken, encompassing consecutive patients subjected to one-level CDA, two-level CDA, or two-level hybrid surgery (HS) for the treatment of CDDD at our institution. Patient demographic and perioperative data were systematically recorded. Radiological images obtained preoperatively, at 1-week post-operation, and during the last follow-up were collected and evaluated, following with statistical analyses. RESULTS: A total of 295 patients and 351 arthroplasty segments were involved in this study. Univariate logistic regressions indicated that age ≥ 45 years and two-level HS was associated with lower risk of BL; and a greater ΔDA (change of disc angle before and after surgery) was correlated with an increased risk of BL. Multivariate logistic regression determined that two-level HS and greater ΔDA were independent preventative and risk factors for BL, respectively. Further analysis revealed that severe BL significantly elevated the risk of implant subsidence compared to non-BL and mild BL. CONCLUSIONS: This study posited bone remodeling and micromotion as potential underlying mechanisms of BL. Subsequent research endeavors should delve into the divergent mechanisms and progression observed between lower- and higher-grade BL, aiming to prevent potential adverse outcomes associated with severe BL.

RESUMEN

While technological advances have made implants a good treatment option with a good long-term prognosis, peri-implantitis, which results in alveolar bone resorption around implants, has been observed in some cases. Micromotion at the implant abutment connection can cause peri-implantitis. However, the temporal progression of micromotion upon loading remains unclear. Therefore, we aimed to longitudinally measure micromotion upon loading application on an implant. Implants with Morse-tapered connections were prepared. Custom titanium abutments were fabricated and tightened onto implant bodies at 35 N. A 100 N vertical load was applied for 200,000 cycles. Micromotion was measured when the load was applied, as was the total implant length and removal torque before and after loading. The micromotion was measured from the position data of the jig of the testing machine during loading. The average removal torque was 30.67 N after 10 min of tightening and 27.95 N after loading, indicating a decrease due to loading. The implant length reduced by 3.6 µm under the load. The average micromotion was 0.018 mm at 2 cycles, 0.016 mm at 100,000 cycles, and 0.0157 mm at 200,000 cycles, indicating implant length reduction under the load but not reaching 0. The micromotion between the implant and abutment under a cyclic load decreased over time but did not completely cease. These results highlight the relationship between micromotion and loading, underscoring the importance of careful monitoring and management to mitigate potential complications, such as peri-implantitis, and ensure optimal performance and durability of the implant.

RESUMEN

INTRODUCTION: Aseptic loosening and periprosthetic fractures are main reasons for revision after THA. Quite different from most other stem systems, Corail cementless hip stems show better survival rates than their cemented counterpart, which can possibly be explained by the use of a collar. The study aimed to investigate primary stability with standard and undersized hip stems both collared and collarless. MATERIALS AND METHODS: Primary stability of cementless, collared and collarless, femoral stems was measured in artificial bones using both undersized and standard size. After preconditioning, 3D micromotion was measured under cyclic loading at the bone-implant interface. RESULTS: The use of a collar resulted in higher micromotion within the same stem size but showed no statistically significant difference for both standard and undersized hip stems. The collared and collarless undersized stems showed no significant differences in 3D micromotion at the upper measuring positions compared to the standard stem size. Micromotion was significantly higher in the distal measuring positions, with and without collar, for the undersized stems (vs. standard collarless stem size). CONCLUSION: The key finding is that the collarless and collared Corail hip stems, within one stem size, showed no significant differences in primary stability. Undersized stems showed significantly higher micromotion in the distal area both with and without collar.

Asunto(s)

RESUMEN

PURPOSE: The present study aimed to identify the optimal design of the unicompartmental femoral component through parameter analysis and stability evaluation. METHODS: A finite element (FE) analysis was applied to analyse and adjust the parameter combinations of the anterior tilt angle of the posterior condyle resection surface, the position of the peg, the length of the peg and the inclination angle of the peg, resulting in 10 different FE models. Setting three knee flexion angles of 8.4° (maximum load state during walking), 40° (maximum load state during stair climbing) and 90° (maximum load state during squatting exercise), quantitatively analysing the micromotion values of the bone-prosthesis interface and defining a weighted scoring formula to evaluate the stability of different FE models. The validity of the FE analysis was verified using the Digital Image Correlation (DIC) device. RESULTS: The errors between the FE analysis and the DIC test at three flexion angles were 5.6%, 1.7% and 11.1%. The 10 different femoral component design models were measured separately. The FE analysis demonstrated that the design with a 0° anterior tilt angle of the posterior condyle resection surface, both pegs placed on the distal resection surface, lengthened 5 mm pegs and a 10° peg inclination angle provided the best stability. CONCLUSION: The current study proposed a method for evaluating the stability of the femoral component design. The optimal intersurface stability design of the unicompartmental femoral component was achieved with two pegs placed on the distal resection surface, a 5-mm peg length increment and a 10° peg inclination. These results might provide a reference for the selection of unicompartmental femoral components in clinical practice and therefore improve the survival rate of future unicompartmental knee arthroplasty. LEVEL OF EVIDENCE: Level III.

Asunto(s)

RESUMEN

PURPOSE: The purpose of this study was to compare micromotion of two new cementless tibial baseplates to a cementless design with well-published clinical success. METHODS: Three cementless tibial baseplate designs (fixed-bearing [FB] with keel and cruciform pegs, rotating-platform with porous central cone and pegs, FB with cruciform keel and scalloped pegs) were evaluated on sawbone models. Loading was applied to the baseplate at a rate of 1 Hz for 10,000 cycles, which represents 6-8 weeks of stair descent. This time frame also represents the approximate time length for the induction of biologic fixation of cementless implants. Compressive and shear micromotion at the sawbone-implant interface were measured. RESULTS: At the end of the loading protocol, the central cone rotating-platform design exhibited greater micromotion at the anterior (p < 0.001), posterior (p < 0.001) and medial locations (p = 0.049) compared to the other two implants. The central cone design also exhibited greater translational micromotion in the sagittal plane at the medial (p = 0.001) and lateral locations (p = 0.034) and in the coronal plane anteriorly (p = 0.007). CONCLUSION: The cementless central cone rotating-platform baseplate demonstrated greater vertical and translational micromotion compared to the two FB baseplates with a keel underloading. This may indicate lower initial mechanical stability in implants without a keel, which possibly affects osseointegration. The implication of this is yet unknown and requires further long-term clinical follow-up to correlate these laboratory findings. LEVEL OF EVIDENCE: V (biomechanical study).

Asunto(s)

RESUMEN

The optimal design of complex engineering systems requires tracing precise mathematical modeling of the system's behavior as a function of a set of design variables to achieve the desired design. Despite the success of current tibial components of knee implants, the limited lifespan remains the main concern of these complex systems. The mismatch between the properties of engineered biomaterials and those of biological materials leads to inadequate bonding with bone and the stress-shielding effect. Exploiting a functionally graded material for the stem of the tibial component of knee implants is attractive because the properties can be designed to vary in a certain pattern, meeting the desired requirements at different regions of the knee joint system. Therefore, in this study, a Ti6Al4V/Hydroxyapatite functionally graded stem with a laminated structure underwent simulation-based multi-objective design optimization for a tibial component of the knee implant. Employing finite element analysis and response surface methodology, three material design variables (stem's central diameter, gradient factor, and number of layers) were optimized for seven objective functions related to stress-shielding and micro-motion (including Maximum stress on the cancellous bone, maximum and mean stresses on predefined paths, the standard deviation of mean stress on paths, maximum and mean micro-motions at the bone-implant interface and the standard deviation of mean micro-motion). Then, the optimized functionally graded stem with 6 layers, a central diameter of 5.59 mm, and a gradient factor of 1.31, was compared with a Ti6Al4V stem for various responses. In stress analysis, the optimal stem demonstrated a 1.92% improvement in cancellous bone stress while it had no considerable influence on the maximum, mean, and standard deviation of stresses on paths. In micro-motion analysis, the maximum, mean, and standard deviation of mean micro-motion at the interface were enhanced by 24.31%, 39.53%, and 19.77%, respectively.

RESUMEN

Natural fracture healing is most efficient when the fine-tuned mechanical force and proper micromotion are applied. To mimick this micromotion at the fracture gap, a near-infrared-II (NIR-II)-activated hydrogel was fabricated by integrating two-dimensional (2D) monolayer Nb2C nanosheets into a thermally responsive poly(N-isopropylacrylamide) (NIPAM) hydrogel system. NIR-II-triggered deformation of the NIPAM/Nb2C hydrogel was designed to generate precise micromotion for co-culturing cells. It was validated that micromotion at 1/300 Hz, triggering a 2.37-fold change in the cell length/diameter ratio, is the most favorable condition for the osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs). Moreover, mRNA sequencing and verification revealed that micromotion-induced augmentation was mediated by Piezo1 activation. Suppression of Piezo1 interrupts the mechano-sensitivity and abrogates osteogenic differentiation. Calvarial and femoral shaft defect models were established to explore the biocompatibility and osteoinductivity of the Micromotion Biomaterial. A series of research methods, including radiography, micro-CT scanning, and immunohistochemical staining have been performed to evaluate biosafety and osteogenic efficacy. The in vivo results revealed that tunable micromotion strengthens the natural fracture healing process through the sequential activation of endochondral ossification, promotion of neovascularization, initiation of mineral deposition, and combinatory acceleration of full-thickness osseous regeneration. This study demonstrated that Micromotion Biomaterials with controllable mechanophysical characteristics could promote the osteogenic differentiation of BMSCs and facilitate full osseous regeneration. The design of NIPAM/Nb2C hydrogel with highly efficient photothermal conversion, specific features of precisely controlled micromotion, and bionic-mimicking bone-repair capabilities could spark a new era in the field of regenerative medicine.

RESUMEN

Osseointegrated transfemoral prostheses experience aseptic complications with an incidence between 3% and 30%. The main aseptic risks are implant loosening, adverse bone remodeling, and post-operative periprosthetic fractures. Implant loosening can either be due to a lack of initial (primary) stability of the implant, which hinders bone ingrowth and therefore prevents secondary stability, or, in the long-term, to the progressive resorption of the periprosthetic bone. Post-operative periprosthetic fractures are most often caused by stress concentrations. A method to simultaneously evaluate the primary stability and the load transfer is currently missing. Furthermore, the measurement errors are seldom reported in the literature. In this study a method to reliably quantify the bone implant interaction of osseointegrated transfemoral prostheses in terms of primary stability and load transfer was developed, and its precision was quantified. Micromotions between the prosthesis and the host bone and the strains on the cortical bone were measured on five human cadaveric femurs with a typical commercial osseointegrated implant. To detect the primary stability of the implant and the load transfer, cyclic loads were applied, simulating the peak load during gait. Digital Image Correlation was used to measure displacements and bone strains simultaneously throughout the test. Permanent migrations and inducible micromotions were measured (three translations and three rotations), while, on the same specimen, the full-field strain distribution on the bone surface was measured. The repeatability tests showed that the devised method had an intra-specimen variability smaller than 6 µm for the translation, 0.02 degrees for the rotations, and smaller than 60 microstrain for the strain distribution. The inter-specimen variability was larger than the intra-specimen variability due to the natural differences between femurs. Altogether, the measurement uncertainties (intrinsic measurement errors, intra-specimen repeatability and inter-specimen variability) were smaller than critical levels of biomarkers for adverse remodelling and aseptic loosening, thus allowing to discriminate between stable and unstable implants, and to detect critical strain magnitudes in the host bone. In conclusion, this work showed that it is possible to measure the primary stability and the load transfer of an osseointegrated transfemoral prosthesis in a reliable way using a combination of mechanical testing and DIC.

RESUMEN

The existing one-time identity authentication technology cannot continuously guarantee the legitimacy of user identity during the whole human-computer interaction session, and often requires active cooperation of users, which seriously limits the availability. This study proposes a new non-contact identity recognition technology based on cardiac micro-motion detection using ultra wideband (UWB) bio-radar. After the multi-point micro-motion echoes in the range dimension of the human heart surface area were continuously detected by ultra wideband bio-radar, the two-dimensional principal component analysis (2D-PCA) was exploited to extract the compressed features of the two-dimensional image matrix, namely the distance channel-heart beat sampling point (DC-HBP) matrix, in each accurate segmented heart beat cycle for identity recognition. In the practical measurement experiment, based on the proposed multi-range-bin & 2D-PCA feature scheme along with two conventional reference feature schemes, three typical classifiers were selected as representatives to conduct the heart beat identification under two states of normal breathing and breath holding. The results showed that the multi-range-bin & 2D-PCA feature scheme proposed in this paper showed the best recognition effect. Compared with the optimal range-bin & overall heart beat feature scheme, our proposed scheme held an overall average recognition accuracy of 6.16% higher (normal respiration: 6.84%; breath holding: 5.48%). Compared with the multi-distance unit & whole heart beat feature scheme, the overall average accuracy increase was 27.42% (normal respiration: 28.63%; breath holding: 26.21%) for our proposed scheme. This study is expected to provide a new method of undisturbed, all-weather, non-contact and continuous identification for authentication.

Asunto(s)