RESUMEN

Despite the great potential of sulfur-based autotrophic denitrification, an improvement in nitrate removal rate is still needed. This study used the desulfurized products of Mn ore to develop the MnS-S0-limestone autotrophic denitrification system (MSLAD). The feasibility of MSLAD for denitrification was explored and the possible mechanism was proposed. The nitrate (100 mg/L) was almost removed within 24 h in batch experiment in MSLAD. Also, an average TN removal of 98 % (472.0 mg/L/d) at hydraulic retention time of 1.5 h in column experiment (30 mg/L) was achieved. MnS and S0 could act as coupled electron donors and show synergistic effects for nitrate removal. γ-MnS with smaller particle size and lower crystallinity was more readily utilized by the bacterium and had higher nitrate removal efficiency than that of α-MnS. Thiobacillus and Sulfurimonas were the core functional bacterium in denitrification. Therefore, MnS-S0-limestone bio-denitrification provides an efficient alternative method for nitrate removal in wastewater.

Asunto(s)

RESUMEN

Manganese sulfide (MnS) is a promising converion-type anode for sodium storage, owing to the virtues of high theoretical capacity, coupled with it crustal abundance and cost-effectiveness. Nevertheless, MnS suffers from inadequate electronic conductivity, sluggish Na+ reaction kinetics and considerable volume variation during discharge/charge process, thereby impeding its rate capability and capacity retention. Herein, a novel lamellar heterostructured composite of Fe-doped MnS nanoparticles/positively charged reduced graphene oxide (Fe-MnS/PG) was synthesized to overcome these issues. The Fe-doping can accelerate the ion/electron transfer, endowing fast electrochemical kinetics of MnS. Meanwhile, the graphene space confinement with strong MnSC bond interactions can facilite the interfacial electron transfer, hamper volume expansion and aggregation of MnS nanoparticles, stabilizing the structural integrity, thus improving the Na+ storage reversibility and cyclic stability. Combining the synergistic effect of Fe-doping and space confinement with strong MnSC bond interactions, the as-produced Fe-MnS/PG anode presents a remarkable capacity of 567 mAh/g at 0.1 A/g and outstanding rate performance (192 mAh/g at 10 A/g). Meanwhile, the as-assembled sodium-ion capacitor (SIC) can yield a high energy density of 119 Wh kg-1 and a maximum power density of 17500 W kg-1, with capacity retention of 77 % at 1 A/g after 5000 cycles. This work offers a promising strategy to develop MnS-based practical SICs with high energy and long lifespan, and paves the way for fabricating advanced anode materials.

RESUMEN

The crystallographic, optical, and electrical properties of manganese sulfide thin films depend on the control of the temperature precursors in the synthesis process, as shown by the results of this work. MnS thin films were deposited on glass substrates using the SILAR method and over an additional layer of CdS synthesized by chemical bath deposition (CBD) to acquire a p-n heterojunction. SILAR is an inexpensive method performed with a homemade robot in this case. Temperature in the solution precursors varied from 20 to 80 °C in four experiments. The morphology and structure of MnS and FTO/CdS/MnS thin films were studied through scanning electron microscopy (SEM) and grazing-incidence X-ray diffraction (GIXRD); the results indicate that materials showed a polycrystalline behavior, a diffraction peak of α- MnS cubic phase was observed with lattice constants values, ranging from 4.74 to 4.75 Å. Additionally, Raman spectroscopy showed a signal corresponding to the transversal optical phonons of MnS at a wavenumber near 300 cm-1. UV-vis spectroscopy showed optical bandgap values of 3.94, 4.0, 4.09, and 4.26 eV for thin films obtained at 20°, 40°, 60°, and 80 °C. respectively. Results indicated 80 °C as an optimal cationic precursor process temperature, achieving optical transmittance T% and good film quality according to SEM and GIXRD for the synthetization of MnS. The current-voltage (I-V) characterization in the heterojunction showed a characteristic diode curve with an open circuit voltage (VOC) of 300 mV under illumination, which indicated that the manganese sulfide behaves as p-type material contributing with positive charge carriers, while CdS behaves as n-type material.

RESUMEN

Improving the adsorption selectivity, enhancing the extraction capacity, and ensuring the structural stability of the adsorbent are the key to realize the high efficiency recovery of uranium. In this work, we utilized the strong Lewis acid-base interaction between S2- and U(VI)O22+ coupling rapid electron transfer at the MnS/U(VI)O22+ solid-liquid interface to achieve excellent selectivity, high adsorption capacity, and rapid extraction of uranium. The as-synthesized MnS adsorbent exhibited an ultrahigh uranium extraction capacity (2457.05 mg g-1) and a rapid rate constant (K = 9.11 × 10-4 g h-1 mg-1) in seawater with 100.7 ppm of UO2(NO3)2 electrolyte. The kinetic simulation reveals that this adsorption process is a chemical adsorption process and conforms to a pseudo-second-order kinetic model, indicating electron transfer at the MnS/U(VI)O22+ solid-liquid interface. The relevant (quasi) in situ spectroscopic characterization and theoretical calculation results further revealed that the outstanding uranium extraction property of MnS could be attributed to the highly selective UO22+ adsorption of MnS with lower adsorption energy as a result of the strong interaction between S2- and UO22+ and the rapid mass transfer and interface electron transfer from S2- and low-valent Mn(II) to U(VI)O22+.

Asunto(s)

RESUMEN

The accumulation of antibiotics in aquatic environments poses a serious threat to human health. Photocatalytic degradation is a promising method for removing antibiotics from water, but its practical implementation requires improvements in photocatalyst activity and recovery. Here, a novel graphite felt-supported MnS/Polypyrrole composite (MnS/PPy/GF) was constructed to achieve effective adsorption of antibiotics, stable loading of photocatalyst, and rapid separation of spatial charge. Systematic characterization of composition, structure and photoelectric properties indicated the efficient light absorption, charge separation and migration of the MnS/PPy/GF, which achieved 86.2% removal of antibiotic ciprofloxacin (CFX), higher than that of MnS/GF (73.7%) and PPy/GF (34.8%). The charge transfer-generated 1O2, energy transfer-generated 1O2, and photogenerated h+ were identified as the dominant reactive species, which mainly attacked the piperazine ring in the photodegradation of CFX by MnS/PPy/GF. The •OH was confirmed to participate in the defluorination of CFX via hydroxylation substitution. The MnS/PPy/GF-based photocatalytic process could ultimately achieve the mineralization of CFX. The facile recyclability, robust stability, and excellent adaptability to actual aquatic environments further confirmed MnS/PPy/GF is a promising eco-friendly photocatalyst for antibiotic pollution control.

Asunto(s)

RESUMEN

High-dispersion polystyrene (PS) microspheres with monodispersity were successfully synthesized by the non-emulsification polymerization method, and three-dimensional (3D) photonic crystals of PS microspheres were fabricated by electrophoretic self-assembly (EPSA). The metal nickel inverse opal structure (IOS) photonic crystal, of which the structural thickness can be freely adjusted via electrochemical deposition (ECD), and subsequently, MnS/MoS2/Ni-IOS specimens were also prepared by ECD. Excellent specific capacitance values (1880 F/g) were obtained at a charge current density of 5 A/g. The samples in this experiment were tested for 2000 cycles of cycle life and still retained a reasonably good level of 76.6% of their initial capacitance value. In this study, the inverse opal structure photonic crystal substrate was used as the starting point, and then the microelectrode material for the MnS/MoS2/Ni-IOS supercapacitor was synthesized. Our findings show that the MnS/MoS2/Ni-IOS microelectrode makes a viable technical contribution to the design and fabrication of high-performance supercapacitors.

RESUMEN

In this study, the crystalline structure and particle shape of Cd1-xMnxS (x~0.3) in the composite photocatalysts prepared by hydrothermal synthesis at different temperatures (T = 80, 100, 120, and 140 °C) were analyzed. Along with mixed Cd-Mn sulfide, the catalysts contain a small amount of ß-Mn3O4. XRD patterns of (Cd,Mn)S have features inherent to both cubic zinc blende and hexagonal wurtzite structure. Moreover, XRD peaks are anisotropically broadened. First, the heterogeneous (or two-phased) model was considered by the commonly used Rietveld method. Phase ratio, average crystallite sizes, and strains for both phases were formally determined. However, it was shown that this model is not correct because relatively narrow and broad peaks cannot be fitted simultaneously. Then, the homogeneous model was tested by Debye Function Analysis. This model assumes that particles are statistically homogeneous, but each particle contains lamellar intergrowth of zinc blende and wurtzite modifications. The probability of stacking faults, as well as the average radii of spherical and ellipsoidal particles, were varied. It was shown that nanocrystalline Cd0.7Mn0.3S particles have an ellipsoidal shape. Ellipsoids are elongated along the direction normal to the plane of defects. An increase in the hydrothermal synthesis temperature from 80 °C to 140 °C leads to an enlargement of particles and a gradual decrease in the probability of stacking faults in the wurtzite structure from 0.47 to 0.36. Therefore, with increasing temperature, the structure of (Cd,Mn)S nanoparticles transforms from almost random polytype cubic/hexagonal (ZB:WZ = 47:53) to a preferably hexagonal structure (ZB:WZ = 36:64). Mn2+ ions facilitate CdS phase transformation from zinc blende to wurtzite structure. There is no direct correlation between the structure and photocatalytic activity.

RESUMEN

The necessity to develop renewable energy resources that are highly durable and flexible with superior energy density and capacitance ability has attracted considerable interest in the field of solar cell research. Semiconducting compound materials that are easily available, hazard-free and cost-effective are emerging as potential solutions to tackle this challenge. Herein, we present multiple molecular precursors used to grow manganese sulfide nanoparticles through a proficient one-step heat-up approach. For all of the tested samples, the X-ray diffraction peaks correspond to a γ-MnS hexagonal wurtzite structure. UV-Vis spectroscopy yielded absorption wavelengths of 359-420 nm and band-gap energies of 3.78-4.0 eV. Photoluminescence analysis shows characteristics of red and blue shift from 451-602 nm. High-resolution transmission electron microscopy (HRTEM) and selected-area electron diffraction (SAED) reveal a narrow size distribution with nanosticks and large contact areas, which are critical for improved catalytic performance. The current study provides an improved pathway to a well-grown and uniform nanocrystal structure for applications in energy devices.

Asunto(s)

RESUMEN

Manganese sulfide (MnS) has unique reactive abilities and can affect the fate and toxicity of contaminants in the natural environment, specifically sulfidic sediments that undergo biogeochemical changes due to natural and artificial processes. However, the effect of oxidization induced by the oxygenation of MnS on organic contaminants remains poorly understood. Herein, we revealed that the hydroxyl radical (HO·) was the dominant reactive oxidant for the rapid degradation of the assessed hydrophobic organic contaminants (including azo dye, nitroaromatic compounds, pesticide, and an endocrine disrupt chemical) during the oxygenation of MnS based on the competitive dynamic experiments, quenching experiments and electron spin resonance (ESR) methods. The removal rates of the assessed organic contaminants were significantly dependent on MnS dosage and co-solutes, including sediment humic acid, metal ions (Mn2+and Fe3+), and inorganic anions (PO43-and Cl-). HO· scavenging by sulfide and its oxidation products (e.g., elemental sulfur), rather than dissolved Mn2+, was responsible for the low utilization efficiency of HO· for the assessed contaminants. The contribution of the manganese oxide (MnO2) generated by the oxygenation of MnS to the examined degradation of contaminants could be neglected. Considered collectively, the reaction between H2O2 and MnO2 generated superoxide radicals (O2-·) which dominated the generation of HO· in an oxic MnS suspension. The results suggest that the impact of oxidization induced by the oxygenation of MnS on environmental contaminants should be of concern in both natural and engineered systems.

Asunto(s)

RESUMEN

Rational structure and morphology design are of great significance to realize excellent Na storage for advanced electrode materials in sodium-ion batteries (SIBs). Herein, a cube-like core/shell composite of single MnS nanocubes (≈50 nm) encapsulated in N, S co-doped carbon (MnS@NSC) with strong CSMn bond interactions is successfully prepared as outstanding anode material for SIBs. The carbon shell significantly restricts the expansion of the MnS volume in successive sodiation/desodiation processes, as demonstrated by in situ transmission electron microscopy (TEM) of one single MnS@NSC nanocube. Moreover, the in situ generated CSMn bonds between the MnS core and carbon shell play a significant role in improving the Na-storage stability and reversibility of MnS@NSC, as revealed by in situ Raman and TEM. As a result, MnS@NSC exhibits a high reversible specific capacity of 594.2 mAh g-1 at a current density of 100 mA g-1 and an excellent rate performance. It also achieves a remarkable cycling stability of 329.1 mAh g-1 after 3000 charge/discharge cycles at 1 A g-1 corresponding to a low capacity attenuation rate of 0.0068% per cycle, which is superior to that of pristine MnS and most of the reported Mn-based anode materials in SIBs.

RESUMEN

Manganese-based nanomaterials have piqued great interest in cancer nanotheranostics, owing to their excellent physicochemical properties. Here we report a facile wet-chemical synthesis of size-controllable, biodegradable, and metastable γ-phase manganese sulfide nanotheranostics, which is employed for tumor pH-responsive traceable gas therapy primed chemodynamic therapy (CDT), using bovine serum albumin (BSA) as a biological template (The final product was denoted as MnS@BSA). The as-prepared MnS@BSA can be degraded in response to the mildly acidic tumor microenvironment, releasing hydrogen sulfide (H2S) for gas therapy and manganese ions for magnetic resonance imaging (MRI) and CDT. In vitro experiments validated the pH-responsiveness of MnS@BSA at pH 6.8 and both H2S gas and •OH radicals were detected during its degradation. In vivo experiments showed efficiently tumor turn-on T1-weighted MRI, significantly suppressed tumor growth and greatly prolonged survival of tumor-bearing mice following intravenous administration of MnS@BSA. Our findings indicated that MnS@BSA nanotheranostics hold great potential for traceable H2S gas therapy primed CDT of cancer.

Asunto(s)

RESUMEN

A comprehensive study of the valence state and the local coordination character of Mn1-xYbxS (x = 0; 0.01; 0.05) solid solutions has been performed using X-ray absorption spectroscopy combined with finite difference method calculations. The good agreement between experimental and calculated data indicates that cationic substitution does not lead to significant changes in the manganese local coordination character. The ytterbium atoms are found to be in the trivalent state, while the manganese and sulfur atoms are in the divalent state.

RESUMEN

Nanostructures can improve battery capacity and cycle life, especially with sulfide electrodes. In this work, a freestanding flexible electrode, consisting of MnS nanoparticles embedded onto carbon nanofibers, was prepared by electrospinning. The produced hybrid was used as an electrode for lithium-ion and sodium-ion batteries. MnS nanoparticles have a size of about 5 nm and the particles are evenly distributed in the carbon nanofibers. Carbon nanofibers act as electronic conductors and buffer the volume change, while MnS nanoparticles react through rapid electrochemical reaction. As a Li-ion battery anode, this hybrid electrode exhibits specific capacities from 240 mAh g-1 at a high current density of 5 A g-1 , up to 600 mAh g-1 at 200 mA g-1 .

RESUMEN

Laser-induced breakdown spectroscopy (LIBS) was used for analysis of the distribution of S,Mn,Fe,Cr,Mo,Si,Al in a 34CrNiMo6 steel sample cut from a main shaft of wind driven generator.The MnS inclusion area in each ablation craters cover zone was extracted in the way of comparing the metallograph captured by optical microscopy before and after LIBS scanning ablation.The statistic relation between MnS inclusion area and signal intensity of S and Mn was analyzed.The result showed that the abnormal signal of S and Mn occurred at the same position with the existence of MnS inclusion,and their signal intensity showed linear relationship.The abnormal signal of S and Mn were triggered mainly by MnS inclusion.The statistic result also showed linear relationship between signal intensity and MnS inclusion area both for S and Mn.It was possible to determine the inclusion type,size and distribution by analyzing abnormal signal.A simplified ablation model was established to calculate the relation of S and Mn content to MnS inclusion area.The arithmetic result showed a linear relation between the content and MnS inclusion area both for S and Mn.The calculation confirmed the linear relationship between signal intensity and inclusion area observed in experiment.The linear relationship could be interfered by macro-segregation,micro-segregation,deviation in measuring inclusion area,and inclusion spatter in pre-ablation.

RESUMEN

Multifunctional nanoplatforms with integrated diagnostic and therapeutic functions have attracted tremendous attention. Especially, the second near-infrared (NIR-II) light response-based nanoplatforms hold great potential in cancer theranostic applications, which is because the NIR-II window provides larger tissue penetration depth and higher maximum permissible exposure (MPE) than that of the well-studied first near-infrared (NIR-I) window. Herein, we for the first time present a two-dimensional (2D)-nanoplatform based on Cu2MnS2 nanoplates (NPs) for magnetic resonance imaging (MRI)/multispectral optoacoustic tomography (MSOT) dual-modal imaging-guided photothermal therapy (PTT) of cancer in the NIR-II window. Methods: Cu2MnS2 NPs were synthesized through a facile and environmentally friendly process. A series of experiments, including the characterization of Cu2MnS2 NPs, the long-term toxicity of Cu2MnS2 NPs in BALB/c nude mice, the applications of Cu2MnS2 NPs for in vitro and in vivo MRI/MSOT dual-modal imaging and NIR-II PTT of cancer were carried out. Results: The as-synthesized Cu2MnS2 NPs exhibit low cytotoxicity, excellent biocompatibility as well as high photothermal conversion efficiency (~49.38%) and outstanding photostability. Together with their good T1-shortening effect and strong absorbance in the NIR-I and NIR-II region, the Cu2MnS2 NPs display high-contrast imaging performance both in MRI and MSOT (900 nm laser source). Moreover, the subsequent in vitro and in vivo results demonstrate that the Cu2MnS2 NPs possess excellent PTT efficacy under 1064 nm laser irradiation with a low power density (0.6 W cm-2). In addition, the detailed long-term toxicity studies further confirming the safety of Cu2MnS2 NPs in vivo. Conclusion: We have developed a new 2D Cu2MnS2 NPs as multifunctional theranostic agents for MRI/MSOT dual-modal imaging-guided PTT of cancer in the NIR-II window. Such biocompatible Cu2MnS2 NPs might provide a new perspective for exploring new 2D-based nanoplatforms with improved properties for clinical applications in the future.

Asunto(s)

RESUMEN

Manganese sulfide (MnS) thin films were synthesized via atomic layer deposition (ALD) using gaseous manganese bis(ethylcyclopentadienyl) and hydrogen sulfide as precursors. At deposition temperatures ≤150 °C phase-pure γ-MnS thin films were deposited, while at temperatures >150 °C, a mixed phase consisting of both γ- and α-MnS resulted. In situ quartz crystal microbalance (QCM) studies validate the self-limiting behavior of both ALD half-reactions and, combined with quadrupole mass spectrometry (QMS), allow the derivation of a self-consistent reaction mechanism. Finally, MnS thin films were deposited on copper foil and tested as a Li-ion battery anode. The MnS coin cells showed exceptional cycle stability and near-theoretical capacity.

RESUMEN

In this work, we demonstrate a general lithium-ion battery electrode fabrication method for colloidal nanoparticles (NPs) using electrophoretic deposition (EPD). Our process is capable of forming robust electrodes from copper sulfide, manganese sulfide, and germanium NPs without the use of additives such as polymeric binders and conductive agents. After EPD, we show two postprocessing treatments ((NH4)2S and inert atmosphere heating) to effectively remove surfactant ligands and create a linked network of particles. The NP films fabricated by this simple process exhibit excellent electrochemical performance as lithium-ion battery electrodes. Additive-free Cu(2-x)S and MnS NP films show well-defined plateaus at ∼1.7 V, demonstrating potential for use as cathode electrodes. Because of the absence of additives in the NP film, this additive-free NP film is an ideal template for ex situ analyses of the particles to track particle morphology changes and deterioration as a result of Li ion cycling. To this end, we perform a size-dependent investigation of Cu(2-x)S NPs and demonstrate that there is no significant relationship between size and capacity when comparing small (3.8 nm), medium (22 nm), and large (75 nm) diameter Cu(2-x)S NPs up to 50 cycles; however, the 75 nm NPs show higher Coulombic efficiency. Ex situ TEM analysis suggests that Cu(2-x)S NPs eventually break into smaller particles (<10 nm), explaining a weak correlation between size and performance. We also report for the first time on additive-free Ge NP films, which show stable capacities for up to 50 cycles at 750 mAh/g.

RESUMEN

We investigated how the outcome of the solvothermal synthesis of manganese(II) sulfide (MnS) nanocrystals (NCs) is affected by the type and amount of long chain surfactant present in the reaction mixture. Prompted by a previous observation that a larger than stoichiometric amount of sulfur is required [Puglisi, A.; Mondini, S.; Cenedese, S.; Ferretti, A. M.; Santo, N.; Ponti A. Chem. Mater. 2010, 22, 2804-2813], we carried out a wide set of reactions using Mn(II) carboxylates and Mn2(CO)10 as precursors with varying amounts of sulfur and carboxylic acid. MnS NCs were obtained provided that the S/Mn ratio was larger than the L/Mn ratio, otherwise MnO NCs were produced. Since MnS can crystallize in three distinct phases (rock salt α-MnS, zincblende ß-MnS, and wurtzite γ-MnS), we also investigated whether the surfactant affected the NC polymorphism. We found that MnS polymorphism can be controlled by appropriate selection of the surfactant. γ-MnS nanocrystals formed when a 1:2 mixture of long chain carboxylic acid and amine was used, irrespective of the presence of carboxylic acid as a free surfactant or ligand in the metal precursor. When we used a single surfactant (carboxylic acid, alcohol, thiol, amine), α-MnS nanocrystals were obtained. The peculiar role of the amine seems to be related to its basicity. The nanocrystals were characterized by TEM and electron diffraction; ATR-FTIR spectroscopy provided information about the surfactants adsorbed on the NCs.

RESUMEN

A spray-based technique, originally developed for the production of semiconductor nanocrystals, is utilized for the preparation of high-quality nanocrystalline thin films, as demonstrated with manganese sulfide. The films are formed by the use of pneumatic-assisted thermospray or pneumatic nebulizers. Our simple, low-cost, and low-temperature process results in a dense and phase-pure grain structure. The concepts and benefits of this technique are described and discussed. The film characteristics show dependence on the experimental parameters, in particular the rate of solvent vaporization. Three alternative film formation mechanisms are suggested for cases with varied experimental conditions.