RESUMEN

The achievement of size uniformity and monodispersity in perovskite quantum dots (QDs) requires the implementation of precise temperature control and the establishment of optimal reaction conditions. Nevertheless, the accurate control of a range of reaction variables represents a considerable challenge. This study addresses the aforementioned challenge by employing manganese (Mn) doping to achieve size uniformity in CsPbBr3 perovskite QDs without the necessity for the precise control of the reaction conditions. By optimizing the Mn:Pb ratio, it is possible to successfully dope CsPbBr3 QDs with the appropriate concentrations of Mn²âº and achieve a uniform size distribution. The spectroscopic measurements on single QDs indicate that the appropriate Mn²âº concentrations can result in a narrower spectral linewidth, a longer photoluminescence (PL) lifetime, and a reduced biexciton Auger recombination rate, thus positively affecting the PL properties. This study not only simplifies the size control of perovskite QDs but also demonstrates the potential of Mn-doped CsPbBr3 QDs for narrow-linewidth light-emitting diode applications.

RESUMEN

Designing high-performance and durable oxygen evolution reaction (OER) catalysts is important for green hydrogen production through anion exchange membrane water electrolysis (AEMWE). Herein, a series of Mn-doped Co-based OER catalysts supported on FeOxHy (FCMx) are presented to enhance the OER activity. Mn doping effectively reduces the size of the Co oxide particles, thereby augmenting the active surface area. Moreover, Mn doping induces the creation of oxygen vacancies, leading to an efficient structural conversion during the OER, which is confirmed via in situ Raman spectroscopy. Under optimal conditions, the catalyst exhibits an overpotential of 234.4 mV at 10 mA cm-2 and a Tafel slope of 37.2 mV dec-1 under half-cell conditions. The AEMWE single-cell system demonstrates a current density of 1560 mA cm-2 at 1.8 V at 60 °C with a degradation rate of 0.4 mV h-1 for 500 h at 500 mA cm-2. Our development of a robust OER catalyst represents notable progress in the field of nonprecious-metal water electrolysis, marking a step toward cost-effective green hydrogen production.

RESUMEN

Electrochemical urea oxidation reaction (UOR) suffers from sluggish reaction kinetics due to its complex 6-electron transfer processes combined with conversion of complicated intermediates, severely retarding the overall energy conversion efficiency. Herein, manganese-doped nickel phosphide nanosheets (Mn-Ni2P) are constructed and employed for driving UOR. Comprehensive analysis deciphers that Mn doping could efficiently accelerate the surface reconstruction of Mn-Ni2P electrode, generating highly reactive NiOOH-MnOOH heterostructure with local nucleophilic and electrophilic regions. Such unique structure could accelerate the targeted adsorption and activation of C and N atoms, promoting fracture of CN bond in urea. In addition, moderate Mn doping could efficiently enhance the adsorption capacities of urea molecules and some key intermediates, and minish the energy barrier for *CO2 desorption, accelerating refreshing of the catalyst. Consequently, the Mn-Ni2P electrode exhibits excellent UOR catalytic activity, achieving an industrial-level current density of 1000 mA cm-2 at 1.46 V (vs. RHE).

Asunto(s)

RESUMEN

Doping engineering of metallic elements is of significant importance in photocatalysis, especially in the transition element range where metals possess empty 'd' orbitals that readily absorb electrons and increase carrier concentration. The doping of Mn ions produces dipole interactions that change the local structure of BiOCl, thus increasing the specific surface area of BiOCl and the number of mesoporous distributions, and providing a broader platform and richer surface active sites for catalytic reactions. The combination of Mn doping and metal Bi reduces the forbidden bandwidth of BiOCl, thereby increasing the absorption in the light region and strengthening the photocatalytic ability of BiOCl. The degradation of norfloxacin by Bi/Mn-doped BiOCl can reach 86.5% within 10 min. The synergistic effect of Mn doping and Bi metal can change the internal energy level and increase light absorption simultaneously. The photocatalytic system created by such a dual-technology combination has promising applications in environmental remediation.

RESUMEN

Nanocomposites SnO2/MnOx with various manganese content (up to [Mn]/[Sn] = 10 mol. %) and different manganese distribution were prepared by wet chemical technique and characterized by X-ray diffraction, scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis and mapping, IR and Raman spectroscopy, total reflection X-ray fluorescence, mass-spectrometry with inductive-coupled plasma (ICP-MS), X-ray photoelectron spectroscopy (XPS), electron paramagnetic resonance (EPR) spectroscopy. A different distribution of manganese between the volume and the surface of the SnO2 crystallites was revealed depending on the total Mn concentration. Furthermore, the identification of surface MnO2 segregation was performed via Raman spectroscopy. There is a strong dependence of the sensor signal toward CO and, especially, NO) on the presence of MnO2 surface segregation. However, manganese ions intruding the SnO2 crystal structure were shown to not almost effect on sensor properties of the material.

RESUMEN

The water polluted by lead(Pb(II)) and cadmium(Cd(II)) seriously endangers ecological safety and needs to be solved urgently. Because of the relatively low adsorption rate of pure hydroxyapatite for heavy metals, a series of manganese-doped hydroxyapatites (MnHAPs) were prepared by using manganese, a common impurity in hydroxyapatite, as a doping element to improve the adsorption performance. The structural and functional groups of the materials with different Mn/(Ca +Mn) molar ratios (0%, 5%, 10%, 20%, and 30%) were investigated by scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET), X-Ray diffraction (XRD), Raman spectrometer and Fourier transform infrared spectroscopy (FTIR) characterization. The presence of manganese influenced the formation and growth of hydroxyapatite crystals, resulting in lattice distortion and a large number of lattice defects in materials. Among them, manganese-doped hydroxyapatite with a Mn/(Ca +Mn) molar ratio of 10% (MnHAP-10) could most effectively remove Pb(II) and Cd(II), with the adsorption capacity of 1806.09 mg g-1 for Pb(II) at pH = 5 and 176.88 mg g-1 for Cd(II) at pH = 5.5. Then the adsorption behavior and mechanism were further researched systemically. It was concluded that the immobilization of Pb(II) by MnHAP-10 was mainly through dissolution precipitation and ion exchange, while Cd(II) was adsorbed by ion exchange and electrostatic interaction. In conclusion, MnHAP-10 has the potential to be applied as an effective adsorbent for the removal of Pb(II) and Cd(II) pollution.

Asunto(s)

RESUMEN

Developing high-performance cathodes with sufficient stability against CO2 rooting in ambient atmosphere is crucial to realizing the practical application of solid-oxide fuel cells. Herein, the Mn dopant is investigated to regulate the phase structure and cathode performance of SrFeO3-δ perovskites through partially replacing the B-site Fe. Compared with parent SrFeO3-δ, Mn-doped materials, SrFe1-xMnxO3-δ (x = 0.05 and 0.1), show stabilized cubic perovskites at room temperature. Meanwhile, doping Mn accelerates the oxygen reduction reaction process, showing a reduced polarization resistance of 0.155 Ω·cm2 at 700 °C for SrFe0.95Mn0.05O3-δ, which is less than 30% of SrFeO3-δ. In addition, the Mn dopant improves the chemical oxygen surface exchange and bulk diffusion coefficients. Furthermore, Mn enhances the tolerance toward CO2 corrosion in various CO2 atmospheres. Density functional theory calculations also reveal that Mn can strengthen the structural stability and increase the activity for the oxygen reduction reaction.

RESUMEN

The release of phenolic-contaminated treated palm oil mill effluent (TPOME) poses a severe threat to human and environmental health. In this work, manganese-modified black TiO2 (Mn-B-TiO2) was produced for the photodegradation of high concentrations of total phenolic compounds from TPOME. A modified glycerol-assisted technique was used to synthesize visible-light-sensitive black TiO2 nanoparticles (NPs), which were then calcined at 300 °C for 60 min for conversion to anatase crystalline phase. The black TiO2 was further modified with manganese by utilizing a wet impregnation technique. Visible light absorption, charge carrier separation, and electron-hole pair recombination suppression were all improved when the band structure of TiO2 was tuned by producing Ti3+ defect states. As a result of the enhanced optical and electrical characteristics of black TiO2 NPs, phenolic compounds were removed from TPOME at a rate of 48.17%, which is 2.6 times higher than P25 (18%). When Mn was added to black TiO2 NPs, the Ti ion in the TiO2 lattice was replaced by Mn, causing a large redshift of the optical absorption edges and enhanced photodegradation of phenolic compounds from TPOME. The photodegradation efficiency of phenolic compounds by Mn-B-TiO2 improved to 60.12% from 48.17% at 0.3 wt% Mn doping concentration. The removal efficiency of phenolic compounds from TPOME diminished when Mn doping exceeded the optimum threshold (0.3 wt%). According to the findings, Mn-modified black TiO2 NPs are the most effective, as they combine the advantages of both black TiO2 and Mn doping.

RESUMEN

Arsenic pollution of water is one of the severest environmental challenges threatening human health. Iron-based nanomaterials have been demonstrated effective in arsenic removal. However, they generally suffer from low removal efficiency towards highly toxic As(III), loss of active sites owing to agglomeration, and poor reusability. Herein, we report a carbonized melamine foam supported Mn(IV)-doped ß-FeOOH nanospindles(CF@Mn-FeOOH NSp) for tackling the technical hurdles. The designed CF@Mn-FeOOH NSp appears as a free-standing monolith through a low-cost and straightforward hydrothermal method. The atomic-scale integration of Mn(IV) into ß-FeOOH enables an oxidation-adsorption bifunctionality, where Mn(IV) serves as oxidizer for As(III) and Fe(III) acts as adsorber for As(V). The maximal adsorption capacity for As(V) and As(III) can reach 152 and 107 mg g-1, respectively. Meanwhile, As in simulated high arsenic groundwater can be decreased to below 10 µg L-1 within 24 h. By simple "filtrating-washing", 85% and 82% of its initial adsorption capacity for As(V) and As(III) can be easily recovered even after 5-cycles reuse. Kinetics and isotherm adsorption study indicate that the arsenic adsorption behavior is mainly through chemical bonding during single-layer adsorbing process. The as-prepared CF@Mn-FeOOH offers a scalable, efficient, and recyclable solution for arsenic removal in groundwater and wastewater from mines and industry.

Asunto(s)

RESUMEN

The doping of halide perovskite nanocrystals (NCs) with manganese cations (Mn2+ ) has recently enabled enhanced stability, novel optical properties, and modulated charge carrier dynamics of the NCs host. However, the influence of Mn doping on the synthetic routes and the band structures of the host has not yet been elucidated. Herein, it is demonstrated that Mn doping promotes a facile, safe, and low-hazard path toward the synthesis of ternary Cs3 Bi2 I9 NCs by effectively inhibiting the impurity phase (i.e., CsI) resulting from the decomposition of the intermediate Cs3 BiI6 product. Furthermore, it is observed that the deepening of the valence band level of the host NCs upon doping at Mn concentration levels varying from 0 to 18.5% (atomic ratio) with respect to the Bi content. As a result, the corresponding Mn-doped NCs solar cells show a higher open-circuit voltage and longer electron lifetime than those employing the undoped perovskite NCs. This work opens new insights on the role of Mn doping in the synthetic route and optoelectronic properties of lead-free halide perovskite NCs for still unexplored applications.

RESUMEN

Ion doping, an effective way to modify the nature of materials, is beneficial for the improvement of material properties. Mn doping exhibits gain of piezoelectric properties in KTa1-x Nb x O3 (KTN). However, the impact mechanism of Mn ions on properties remains unclear. Here, the effects of Mn doping on local heterogeneity and piezoelectric properties in KTN are studied. The electric field-induced strain of Mn-doped KTN is ∼0.25% at 10 kV cm-1, 118% higher than that of pristine KTN. Meanwhile, as a result of Mn doping, the dielectric permittivity was tripled and the ferroelectricity was modified. The changes in A1(2TO), B1 + E(3TO) and E(4TO) vibrations characterized by Raman spectra indicate increased local polarization, weak correlation of dipoles and distorted lattices in Mn-doped KTN, respectively. First-principles calculations demonstrate stronger local heterogeneity introduced by Mn dopants, which weakens the dipole correlations and reduces domain sizes. As a result, the decreased domain sizes, combined with the larger ratio of lattice parameters c and a of the Mn-contained portion, are responsible for the higher piezoelectricity. This work reveals the impact on properties of KTN from Mn dopants and the prominent role of local heterogeneity in improving piezoelectricity, being valuable for the optimization and design of material properties.

RESUMEN

Driven by an ever-growing demand for environmentally compatible materials, the past two decades have witnessed the booming development in the field of piezoelectrics. To maximally explore the potential of lead-free piezoelectrics, chemical doping could be an effective approach, referenced from tactics adopted in lead-based piezoelectrics. Herein, we reveal the distinct role of manganese in a promising lead-free perovskite (K, Na)NbO3 (denoted by KNN) in comparison to that in market-dominating lead-based counterparts [Pb(Zr, Ti)O3, PZT]. In contrast to the scenario in PZT, manganese doping in KNN results in tremendously improved piezoelectric coefficient d33 by nearly 200%, whereas the same doping species in PZT deteriorates the d33 down to less than 30% of its original value. The result is rationalized from macroscopic and local electrical characterizations down to atomic-scale visualization. This study demonstrates that there is enormous space to further enhance piezoelectricity in lead-free systems because the chemical doping effect may completely differ in lead-containing and lead-free perovskites.

RESUMEN

Ternary Cd1-xInxTe semiconductor nanoparticles have been demonstrated to be sensitizers for solar cell devices. The chemical bath deposition (CBD) process was used to synthesize Cd1-xInxTe nanoparticles, which were deposited onto a mesoporous TiO2 photoelectrode. Individual nanoparticles were estimated to have an average diameter range of ∼10nm. The atomic percentages of chemical elements for Mn(2+)-doped Cd1-xInxTe show that the structure could be Mn(2+)-doped CdInTe incorporated with CdIn2Te4 structure. The resulted X-ray diffraction and diffraction ring patterns of Mn(2+)-doped Cd1-xInxTe nanoparticles indicated the structure to be tetragonal. The optical band gaps were also decreased to 0.9eV after Mn(2+) doping, compared with Eg=1.47eV for undoped Cd1-xInxTe(7). The best efficiency of 0.51% under 100 mW/cm(2) (AM 1.5G) was obtained after Mn(2+) doping with a short-circuit current density (Jsc) of 1.71mA/cm(2), an open-circuit voltage (Voc) of 0.739V and a fill factor (FF) of 40.2%. This work demonstrated the feasibility of using Cd1-xInxTe with Mn(2+) doping as a broadband solar absorber for TiO2 photoelectrodes.

RESUMEN

Although semiconductor quantum dots are promising materials for displays and lighting due to their tunable emissions, these materials also suffer from the serious disadvantage of self-absorption of emitted light. The reabsorption of emitted light is a serious loss mechanism in practical situations because most phosphors exhibit subunity quantum yields. Manganese-based phosphors that also exhibit high stability and quantum efficiency do not suffer from this problem but in turn lack emission tunability, seriously affecting their practical utility. Here, we present a class of manganese-doped quantum dot materials, where strain is used to tune the wavelength of the dopant emission, extending the otherwise limited emission tunability over the yellow-orange range for manganese ions to almost the entire visible spectrum covering all colors from blue to red. These new materials thus combine the advantages of both quantum dots and conventional doped phosphors, thereby opening new possibilities for a wide range of applications in the future.