RESUMEN

Achieving selective detection of ppb-level CO is important for air quality testing at industrial sites to ensure personal safety. Noble metal doping enhances charge transfer, which in turn reduces the detection limit of metal oxide gas sensors. In this work, metal-organic framework-derived Au-doped In2O3 nanotubes with high electrical conductivity are synthesized by pyrolysis of the Au-doped metal-organic framework (In-MIL-68) as a template. Gas-sensing experiments reveal that the detection limit of 0.2% Au-doped In2O3 nanotubes (0.2% Au, mass fraction) is as low as 750 ppb. Meanwhile, the sensing material shows a response value of 18.2 to 50 ppm of CO at 240 °C, which is about 2.8 times higher than that of pure In2O3. Meanwhile, the response and recovery times are short (37 s/86 s). The gas-sensing mechanism of CO is uncovered by in situ DRIFTS through the reaction intermediates. In addition, first-principles calculations suggest that Au doping of In2O3 significantly enhances its adsorption energy for CO and improves the electron transfer properties. This study reveals a novel synthesis pathway for Au-doped In2O3 nanotubular structures and their potential application in low concentration CO detection.

Asunto(s)

RESUMEN

Thick polycrystalline perovskite films synthesized by using solution processes show great potential in X-ray detection applications. However, due to the evaporation of the solvent, many pinholes and defects appear in the thick films, which deteriorate their optoelectronic properties and diminish their X-ray detection performance. Therefore, the preparation of large area and dense perovskite thick films is desired. Herein, we propose an effective strategy of filling the pores with a saturated precursor solution. By adding the saturated perovskite solution to the polycrystalline perovskite thick film, the original perovskite film will not be destroyed because of the solution-solute equilibrium relationship. Instead, it promotes in situ crystal growth within the thick film during the annealing process. The loosely packed grains in the original thick perovskite film are connected, and the pores and defects are partially filled and fixed. Finally, a much denser perovskite thick film with improved optoelectronic properties has been obtained. The optimized thick film exhibits an X-ray sensitivity of 1616.01 µC Gyair-1 cm-2 under an electric field of 44.44 V mm-1 and a low detection limit of 28.64 nGyair s-1 under an electric field of 22.22 V mm-1. These values exceed the 323.86 µC Gyair-1 cm-2 and 40.52 nGyair s-1 of the pristine perovskite thick film measured under the same conditions. The optimized thick film also shows promising working stability and X-ray imaging capability.

RESUMEN

Bismuth-based halide perovskites have shown great potential for direct X-ray detection, attributable to their nontoxicity and advantages in detection sensitivity and spatial resolution. However, the practical application of such materials still faces the critical challenge of combining both high sensitivity and low detection limits. Here, we report a new type of zero-dimensional (0D) perovskite (HIS)BiI5 (1, where HIS2+ = histamine) with high sensitivity and a low detection limit. Structurally, the strong N-H···I hydrogen bonds between HIS2+ cations and inorganic frameworks enhance the rigidity of the structure and diminish the intermolecular distance between adjacent inorganic [Bi2I10]4- dimers. By virtue of such structural merits, single crystal 1 exhibits excellent physical properties perpendicular to both the (001) and (010) faces. Perpendicular to the (010) face, 1 exhibited a high electrical resistivity (2.31 × 1011 Ω cm) and a large carrier mobility-lifetime product (µτ) (2.81 × 10-4 cm2 V-1) under X-ray illumination. Benefiting from these superior physical properties, it demonstrates an excellent X-ray detection capability with a sensitivity of approximately 103 µC Gyair-1 cm-2 and a detection limit of 36 nGyair s-1 in both directions perpendicular to the (001) and (010) crystal faces. These results provide a promising candidate material for the development of new, lead-free, high-performance X-ray detectors.

RESUMEN

The imperative development of a cutting-edge environmental gas sensor is essential to proficiently monitor and detect hazardous gases, ensuring comprehensive safety and awareness. Nanostructures developed from metal oxides are emerging as promising candidates for achieving superior performance in gas sensors. NO2 is one of the toxic gases that affects people as well as the environment so its detection is crucial. The present study investigates the gas sensing capability of copper oxide-based sensor for 5 ppm of NO2 gas at 100 °C. The sensing material was synthesized using a facile precipitation method and characterized by XRD, FE-SEM, UV-visible spectroscopy, photoluminescence spectroscopy, XPS and BET techniques. The developed material shows a response equal to 67.1% at optimal temperature towards 5 ppm NO2 gas. The sensor demonstrated an impressive detection limit of 300 ppb, along with a commendable percentage response of 5.2%. Under optimized conditions, the synthesized material demonstrated its high selectivity, as evidenced by the highest percentage response recorded for NO2 gas among NO2, NH3, CO, CO2 and H2S.

RESUMEN

Herein, we report a dual-functional flexible sensor (DFFS) using a magnetic conductive polymer composed of nickel (Ni), carbon black (CB), and polydimethylsiloxane (PDMS). The material selection for the DFFS utilizes the excellent elasticity of the PDMS matrix and the synergistic interaction between Ni and CB. The DFFS has a wide strain range of 0-170%, a high sensitivity of 74.13 (140-170%), and a low detection limit of 0.3% strain. The DFFS based on superior performance can accurately detect microstrain/microvibration, oncoming/contacting objects, and bicycle riding speed. Additionally, the DFFS can be used for comprehensive monitoring of human movements. Therefore, the DFFS of this work shows significant value for implementation in intelligent wearable devices and noncontact intelligent control.

Asunto(s)

RESUMEN

BACKGROUND: The accurate and rapid detection of blood lead concentration is of paramount importance for assessing human lead exposure levels. Fluorescent protein-based probes, known for their high detection capabilities and low toxicity, are extensively used in analytical sciences. However, there is currently a shortage of such probes designed for ultrasensitive detection of Pb2+, and no reported probes exist for the quantitative detection of Pb2+ in blood samples. This study aims to fill this critical void by developing and evaluating a novel fluorescent protein-based probe that promises accurate and rapid lead quantification in blood. RESULTS: A simple and small-molecule fluorescent protein-based probe was successfully constructed herein using a peptide PbrBD designed for Pb2+ recognition coupled to a single fluorescent protein, sfGFP. The probe retains a three-coordinate configuration to identify Pb2+ and has a high affinity for it with a Kd' of 1.48 ± 0.05 × 10-17 M. It effectively transfers the conformational changes of the peptide to the chromophore upon Pb2+ binding, leading to fast fluorescence quenching and a sensitive response to Pb2+. The probe offers a broad dynamic response range of approximately 37-fold and a linear detection range from 0.25 nM to 3500 nM. More importantly, the probe can resist interference of metal ions in living organisms, enabling quantitative analysis of Pb2+ in the picomolar to millimolar range in serum samples with a recovery percentage of 96.64%-108.74 %. SIGNIFICANCE: This innovative probe, the first to employ a single fluorescent protein-based probe for ultrasensitive and precise analysis of Pb2+ in animal and human serum, heralds a significant advancement in environmental monitoring and public health surveillance. Furthermore, as a genetically encoded fluorescent probe, this probe also holds potential for the in vivo localization and concentration monitoring of Pb2+.

Asunto(s)

RESUMEN

Optimizing materials and associated structures for detecting various environmental gas pollutant concentrations has been a major challenge in environmental sensing technology. Semiconducting metal oxides (SMOs) fabricated at the nanoscale are a class of sensor technology in which metallic species are functionalized with various dopants to modify their chemiresistivity and crystalline scaffolding properties. Studies focused on recent advances of gas sensors utilizing metal oxide nanostructures with a special emphasis on the structure-surface property relationships of some typical n-type and p-type SMOs for efficient gas detection are presented. Strategies to enhance the gas sensor performances are also discussed. These oxide material sensors have several advantages such as ease of handling, portability, and doped-based SMO sensing detection ability of environmental gas pollutants at low temperatures. SMO sensors have displayed excellent sensitivity, selectivity, and robustness. In addition, the hybrid SMO sensors showed exceptional selectivity to some CWAs when irradiated with visible light while also displaying high reversibility and humidity independence. Results showed that TiO2 surfaces can sense 50 ppm SO2 in the presence of UV light and under operating temperatures of 298-473 K. Hybrid SMO displayed excellent gas sensing response. For example, a CuO-ZnO nanoparticle network of a 4:1 vol.% CuO/ZnO ratio exhibited responses three times greater than pure CuO sensors and six times greater than pure ZnO sensors toward H2S. This review provides a critical discussion of modified gas pollutant sensing capabilities of metal oxide nanoparticles under ambient conditions, focusing on reported results during the past two decades on gas pollutants sensing.

RESUMEN

A novel fluorescent probe N'-(2-hydroxybenzylidene)-indole-3-formylhydrazine (JHK) was designed and synthesized based on the condensation reaction of indole-3-formylhydrazine and salicylaldehyde. The probe JHK solution could highly selectively recognize Al3+ by the obvious fluorescence enhancement (288-fold) after adding Al3+. And the probe solution with Al3+ had a very high fluorescence quantum yield (89.29 %). The detection limit was calculated to be 1.135 nM, which was significantly lower than many reported detection limits, indicating that the probe JHK had pretty good sensitivity. The ratio of JHK to Al3+ (1:1) and the sensing mechanism were determined by Job's plot, 1H NMR spectra, FTIR spectra, ESI-MS and Gaussian calculation. The probe solution and medium-speed filter paper were successfully used to make test papers for more convenient detection of Al3+. Furthermore, the probe JHK had been successfully applied to the detection of Al3+ in real water, zebrafish and living cells.

Asunto(s)

RESUMEN

Nucleic acid (NA) is a widely-used biomarker for viruses. Accurate quantification of NA can provide a reliable basis for point-of-care diagnosis and treatment. Here, we propose a tilted fiber Bragg grating (TFBG)-based plasmonic fiber-optic spectral comb for fast response and ultralow limit NA detection. The TFBG is coated with a gold film which enables excitation of surface plasmon resonance (SPR), and single-stranded probe NAs with known base sequences are assembled on the gold film. To enhance sensitivity of refractive index (RI) for sensing a chosen combination of probe and target NAs around the TFBG surface, gold nanoparticles (AuNPs) are bonded to the target NA molecules as "RI-labels". The NA combination-induced aggregation of AuNPs induces significant spectral responses in the TFBG that would be below the detection threshold for the NAs in the absence of the AuNPs. The proposed TFBG-SPR NA sensor shows a fast response time of 30 s and an ultra-wide NA detection range from 1 × 10-18 mol/L to 1 × 10-7 mol/L. In the NA concentration range of 1 × 10-12 mol/L (1 pM) to 105 pM, an ultra-high sensitivity of 1.534 dB/lg(pM) is obtained. The sensor achieves an ultra-low limit of detection down to 1.0 × 10-18 mol/L (1 aM), which is more than an order of magnitude lower than the previous reports. The proposed sensor not only shows potentials in practical applications of NA detection, but also provides a new way for TFBG-SPR biochemical sensors to achieve higher RI sensitivity.

Asunto(s)

RESUMEN

2D Ruddlesden-Popper (RP) perovskites have been intensively investigated due to their superior stability and outstanding optoelectrical properties. However, investigations on 2D RP perovskites are mainly focused on A-site substituted perovskites and few reports are on X-site substituted perovskites especially in X-ray detection field. Here, X-site substituted 2D RP perovskite Cs2 Pb(SCN)2 Br2 polycrystalline wafers are prepared and systematically studied for X-ray detection. The obtained wafers show a large resistivity of 2.0 × 1010 Ω cm, a high ion activation energy of 0.75 eV, a small current drift of 2.39 × 10-6 nA cm-1 s-1 V-1 , and charge carrier mobility-lifetime product under X-ray as high as 1.29 × 10-4 cm2 V-1 . These merits enable Cs2 Pb(SCN)2 Br2 wafer detectors with a sensitivity of 216.3 µC Gyair -1 cm-2 , a limit of detection of 42.4 nGyair s-1 , and good imaging ability with high spatial resolution of 1.08 lp mm-1 . In addition, Cs2 Pb(SCN)2 Br2 wafer detectors demonstrate excellent operational stability under high working field up to 2100 V cm-1 after continuous X-ray irradiation with a total dose of 45.2 Gyair . The promising features such as short octahedral spacing and weak ion migration will open up a new perspective and opportunity for SCN-based 2D perovskites in X-ray detection.

RESUMEN

Hydrogen sulfide (H2S) is widely found in oil and natural gas wells and industrial wastewater tanks. Owing to its high toxicity, the monitoring and detection of H2S in the air is essential. However, recent techniques for the quantitative detection of H2S gas suffer from limitations such as high cost, complicated operation, and insufficient sensitivity, preventing their practical application in industry. Thus, we have developed a portable test paper for real-time and inexpensive monitoring of H2S gas by color changes. The test paper had a significantly low H2S detection limit of 200 ppb, which is considered safe for humans. Moreover, the color of the test paper did not change noticeably when exposed to CO2, N2, O2, and air environments, indicating that the test paper is selective for H2S gas and can be stored for a long time. In addition, we fitted a color difference linear model between the color difference values (ΔE) and the concentrations of H2S gas. The establishment of the linear model substantiates that the test paper can provide accurate intensity information when detecting H2S gas leakage.

Asunto(s)

RESUMEN

Halide hybrid perovskites are a kind of intriguing contenders for X-ray detection, and their low detection limits (LoDs) have played a crucial part in X-ray safety inspection and medical examination. However, there is still a significant challenge in manufacturing perovskite X-ray detectors with low LoDs. Herein, attributed to the bulk photovoltaic effect (BPVE) of a Dion-Jacobson (DJ) type 2D halide hybrid perovskite polar structure (3-methylaminopropylamine)PbBr4 (1), self-powered X-ray detection with low detection limit is successfully realized. Specifically, the crystal-based detector of 1 exhibits a low dark current at zero bias, which reduces the noise current (0.34 pA), leading to a low detection limit (58.3 nGyair s-1 ) which is two orders of magnitude lower than that of under external voltage bias. The combination of BPVE and LoDs of halide hybrid perovskite provides an efficient strategy to achieve passive X-ray detection with low doses.

RESUMEN

Broadband photodetectors (PDs) with low detection limits hold significant importance to next-generation optoelectronic devices. However, simultaneously detecting broadband (i.e., X-ray to visible regimes) and weak lights in a single semiconducting material remains highly challenging. Here, by alloying iodine-substituted short-chain cations into the 3D FAPbI3 (FA = formamidine), a new 2D bilayered lead iodide hybrid perovskite, (2IPA)2 FAPb2 I7 (1, 2IPA = 2-iodopropylammonium), that enables addressing this challenge is reported. Such a 2D multilayered structure and lead iodide composition jointly endow 1 with a minimized dark current (6.04 pA), excellent electrical property, and narrow bandgap (2.03 eV), which further gives it great potential for detecting broadband weak lights. Consequently, its high-quality single crystal PDs exhibit remarkable photoresponses to weak ultraviolet-visible lights (377-637 nm) at several tens of nW cm-2 with high responsivities (>102  mA W-1 ) and significant detectivities (>1012 Jones). Moreover, 1 has an excellent X-ray detection performance with a high sensitivity of 438 µC Gy-1 cm-2 and an ultralow detection limit of 20 nGy s-1 . These exceptional attributes make 1 a promising material for broadband weak lights detection, which also sheds light on future explorations of high-performance PDs based on 2D hybrid perovskites.

RESUMEN

Perovskite single crystals and polycrystalline films have complementary merits and deficiencies in X-ray detection and imaging. Herein, we report preparation of dense and smooth perovskite microcrystalline films with both merits of single crystals and polycrystalline films through polycrystal-induced growth and hot-pressing treatment (HPT). Utilizing polycrystalline films as seeds, multi-inch-sized microcrystalline films can be in situ grown on diverse substrates with maximum grain size reaching 100 µm, which endows the microcrystalline films with comparable carrier mobility-lifetime (µτ) product as single crystals. As a result, self-powered X-ray detectors with impressive sensitivity of 6.1×104  µC Gyair -1 cm-2 and low detection limit of 1.5 nGyair s-1 are achieved, leading to high-contrast X-ray imaging at an ultra-low dose rate of 67 nGyair s-1 . Combining with the fast response speed (186 µs), this work may contribute to the development of perovskite-based low-dose X-ray imaging.

RESUMEN

The detection of trace biomarkers is an important supplementary approach for early screening and diagnoses of tumors. An optical fiber near-field enhanced plasmonic resonance immunoprobe is developed for the detection of the hepatocellular carcinoma biomarker, i.e., the alpha-fetoprotein. Generic principles based on dispersion models and finite element analysis (FEA) models are developed to realize the optimized configuration of spectral characteristics of the immunoprobe. Dispersion models provide theoretical guidance for the design of the multilayer sensing structure from the perspective of the ray optics theory. FEA models provide theoretical guidance for the selection of coating materials from the perspective of the self-defined dielectric constant ratio, i.e., the ratio of the real part to the imaginary part. The optimized configuration of the antibody coupling further improves the biosensing performance of the immunoprobe. The limit of detection (LOD) can reach down to 0.01 ng mL-1 , which is one order of magnitude lower than those relevant reported works. Such a low LOD can more effectively avoid the accuracy degradation of detection results due to measurement errors. Human serum samples have also been detected, with the good precision achieved. This work shows promising prospects in applications of label-free, low-cost, rapid, and convenient early screening of tumors.

Asunto(s)

RESUMEN

Palladium is a key element in fuel cells, electronic industries, and organic catalysis. At the same time, chromium is essential in leather, electroplating, and metallurgical industries. However, their unpremeditated leakage into aquatic systems has caused human health and environmental apprehensions. Herein, we reported the development of an sp2 carbon-conjugated fluorescent covalent organic framework with a guanidine moiety (sp2 c-gCOF) that showed excellent thermal and chemical stability. The sp2 c-gCOF showed effective sensing, capture, and recovery/removal of Pd(II) and Cr(VI) ions, which could be due to the highly accessible pore walls decorated with guanidine moieties. The fluorescent sp2 c-gCOF showed higher selectivity for Pd(II) and Cr(VI) ions, with an ultra-low detection limit of 2.7 and 3.2 nM, respectively. The analysis of the adsorption properties with a pseudo-second-order kinetic model showed that sp2 c-gCOF could successfully and selectively remove both Pd(II) and Cr(VI) ions from aqueous solutions. The polymer also showed excellent capture efficacy even after seven consecutive adsorption-desorption cycles. Hence, this study reveals the potential of fluorescent sp2 c-gCOF for detecting, removing, and recovering valuable metals and hazardous ions from wastewater, which would be useful for economic benefit, environmental safety, human health, and sustainability. The post-synthetic modification of sp2 c-COF with suitable functionalities could also be useful for sensing and extracting other water pollutants and valuable materials from an aqueous system.

RESUMEN

Recently, flexible stretchable sensors have been gaining attention for their excellent adaptability for electronic skin applications. However, the preparation of stretchable strain sensors that achieve dual-mode sensing while still retaining ultra-low detection limit of strain, high sensitivity, and low cost is a pressing task. Herein, a high-performance dual-mode stretchable strain sensor (DMSSS) based on biomimetic scorpion foot slit microstructures and multi-walled carbon nanotubes (MWCNTs)/graphene (GR)/silicone rubber (SR)/Fe3 O4 nanocomposites is proposed, which can accurately sense strain and magnetic stimuli. The DMSSS exhibits a large strain detection range (≈160%), sensitivity up to 100.56 (130-160%), an ultra-low detection limit of strain (0.16% strain), and superior durability (9000 cycles of stretch/release). The sensor can accurately recognize sign language movement, as well as realize object proximity information perception and whole process information monitoring. Furthermore, human joint movements and micro-expressions can be monitored in real-time. Therefore, the DMSSS of this work opens up promising prospects for applications in sign language pose recognition, non-contact sensing, human-computer interaction, and electronic skin.

Asunto(s)

RESUMEN

The prerequisites for rapid screening of total bacteria in drinking water are low detection limit and convenience. Inspired by commercial adenosine 5'-triphosphate (ATP) based total bacterial detection kits, we pursued likewise convenience but with much lower detection limit. Existing intercalation fluorescence-based techniques employ multiple reagents to permeate the cell membrane and intercalate dye into the DNA in discrete sequential steps. A simple multi-functional reagent is proposed to do the same within one step. Surfactants (TritonX and SDS), and intercalating dyes (SYBR green, SYBR gold) were examined for their mutual compatibility and augmented with EDTA. Evaluation was performed with Gram negative Escherichia coli K12 (E. coli K12) and Gram positive Bacillus subtilis (B. subtilis) at serial dilution ratios from 10-6 to 10-2. Comparison was made with absorbance (600 nm) measurements and a commercial ATP kit. Using charge integrated photodetection, the proposed 1-step reagent achieved an LOD (1.00 × 10-6, B. subtilis) that is two orders of magnitude lower than that of ATP kit (LOD = 1.06× 10-4). This means it could detect minute quantity of total bacteria that is otherwise undetected by the ATP kit.

Asunto(s)

RESUMEN

Porcine epidemic diarrhea virus (PEDV), a coronavirus that causes highly infectious intestinal diarrhea in piglets, has led to severe economic losses worldwide. Rapid diagnosis and timely supervision are significant in the prophylaxis of PEDV. Herein, we proposed a gold-nanorod (GNR) probe-assisted counting method using dark field microscopy (DFM). The antibody-functionalized silicon chips were prepared to capture PEDV to form sandwich structures with GNR probes for imaging under DFM. Results show that our DFM-based assay for PEDV has a sensitivity of 23.80 copies/µL for simulated real samples, which is very close to that of qPCR in this study. This method of GNR probes combined with DFM for quantitative detection of PEDV not only has strong specificity, good repeatability, and a low detection limit, but it also can be implemented for rapid on-site detection of the pathogens.

Asunto(s)

RESUMEN

Light activation is an effective method to improve sensor performance at room temperature (RT). This work realized the effective detection of trace-level NO2 at RT under visible light by combining ZnO with the excellent photocatalyst BiOI. A 1.5 atom % BiOI-ZnO-based sensor under 520 nm light exhibited optimal sensing properties with the maximum responses (13.9 to 1 ppm NO2), fast response/recovery time (66 s/47 s to 1 ppm), and a low detection limit of 25 ppb (theoretically 0.34 ppb). In the meantime, the sensor also possessed excellent selectivity, repeatability, and stability. The excellent properties were attributed to the high concentration of oxygen vacancies and the prolonged lifetime of photogenerated carriers. In addition, the observed photovoltaic effect of the sensor at RT indicated that the sensor held application prospects in the photovoltaic self-power field.

Asunto(s)