RESUMEN
An electroactive polyazomethine was prepared directly on a transparent electrode by the polycondensation of bis(triphenylamine) dialdehyde and its complementary methoxytriphenylamine diamine. The spray-and-bake method of coating the electrode for preparing electrochromic layers could be upscaled to prepare working devices larger than standard test devices. The film prepared by thermally annealing the complementary monomers was both electroactive and switched its color with an applied potential. The yellow electrochromic polyazomethine could be electrochemically oxidized reversibly to obtain a blue film. The electrochromic test device fabricated from the polyazomethine was operated upwards of 1 h for performance assessment. The electrochromic response times of the electrochromic device were ca. 3.3 and 1.2 s for the coloration and bleaching, respectively. The upscaled device prepared by the straightforward coating approach had consistent metrics with the small-area test device.
RESUMEN
Conjunctival goblet cells (CGCs) are specialized epithelial cells playing key roles for ocular surface homeostasis, and their examination is important for diagnosing ocular surface diseases. Despite recent advancements in high-contrast CGC imaging for non-invasive examination, significant challenges remain for human applications. High-speed large-area imaging over the curved ocular surface is needed to assess statistically meaningful CGCs in the extensive human conjunctiva. To address this challenge, we developed a novel surface detection method and an integrated microscopy system for human use. With both a long detection range of 2 mm and a high update rate of 50 Hz, the surface detection method enabled real-time surface tracking during large-area imaging. The integrated microscopy could complete 5 × 2 patch imaging in approximately 10 s. CGC density analysis showed significantly reduced uncertainties with large-area imaging. This is the first demonstration of non-contact large-area cellular examination in humans, and this new development holds promise for non-invasive CGC examination and accurate diagnosis of ocular surface diseases.
RESUMEN
Biomimicking the chemical, mechanical, and topographical properties of bone on an implant model is crucial to obtain rapid and effective osteointegration, especially for the large-area fractures of the skeletal system. Titanium-based biomaterials are more frequently preferred in clinical use in such cases and coating these materials with oxide layers having chemical/nanotopographic properties to enhance osteointegration and implantation success rates has been studied for a long time. The objective of this study is to examine the high and rapid mineralization potential of anodized aluminum oxide (AAO) coated and atomic layer deposition (ALD)-alumina coated titanium substrates on large deformation areas with difficult spontaneous healing. AAO-coated titanium (AAO@Ti) substrates were fabricated via anodization technique in different electrolytes and their osteogenic potential was analyzed by comparing them to the bare titanium surface as a control. In order to investigate the effect of the ionic characters gained by the surfaces through anodization, the oxidized nanotopographic substrates were additionally coated with an ultrathin alumina layer via ALD (ALD@AAO@Ti), which is a sensitive and conformal coating vapor deposition technique. Besides, a bare titanium sample was also coated with pure alumina by ALD (ALD@Ti) to investigate the effect of nanoscale surface morphology. XPS analysis after ALD coating showed that the ionic character of each surface fabricated by anodization was successfully suppressed. In vitro studies demonstrated that, among the substrates investigated, the mineralization capacity of MG-63 osteosarcoma cells were highest when incubated on ALD-treated and bare AAO@Ti samples that were anodized in phosphoric acid (H3PO4_AAO@Ti and ALD@H3PO4_AAO@Ti). Mineralization on these substrates also increased consistently beginning from day 2 to day 21. Moreover, immunocytochemistry for osteopontin (OPN) demonstrated the highest expression for ALD@H3PO4_AAO@Ti, followed by the H3PO4_AAO@Ti sample. Consequently, it was observed that, although ALD treatment improves cellular characteristics on all samples, effective mineralization requires more than a simple ALD coating or the presence of a nanostructured topography. Overall, ALD@H3PO4_AAO@Ti substrates can be considered as an implant alternative with its enhanced osteogenic differentiation potential and rapid mineralization capacity.
RESUMEN
Perovskite solar cells have been proven to enhance cell characteristics by introducing passivation materials that suppress defect formation. Defect states between the electron transport layer and the absorption layer reduce electron extraction and carrier transport capabilities, leading to a significant decline in device performance and stability, as well as an increased probability of non-radiative recombination. This study proposes the use of an amino acid (L-Histidine) self-assembled monolayer material between the transport layer and the perovskite absorption layer. Surface analysis revealed that the introduction of L-Histidine improved both the uniformity and roughness of the perovskite film surface. X-ray photoelectron spectroscopic analysis showed a reduction in oxygen vacancies in the lattice and an increase in Ti4+, indicating that L-Histidine successfully passivated trap states at the perovskite and TiO2 electron transport layer interface. In terms of device performance, the introduction of L-Histidine significantly improved the fill factor (FF) because the reduction in interface defects could suppress charge accumulation and reduce device hysteresis. The FF of large-area solar modules (25 cm2) with L-Histidine increased from 55% to 73%, and the power conversion efficiency (PCE) reached 16.5%. After 500 h of aging tests, the PCE still maintained 91% of its original efficiency. This study demonstrates the significant impact of L-Histidine on transport properties and showcases its potential for application in the development of large-area perovskite module processes.
RESUMEN
Carbon-based perovskite solar cells (PSCs) coupled with solution-processed hole transport layers (HTLs) have shown potential owing to their combination of low cost and high performance. However, the commonly used poly(3-hexylthiophene) (P3HT) semicrystalline-polymer HTL dominantly shows edge-on molecular orientation, in which the alkyl side chains directly contact the perovskite layer, resulting in an electronically poor contact at the perovskite/P3HT interface. The study adopts a synergetic strategy comprising of additive and solvent engineering to transfer the edge-on molecular orientation of P3HT HTL into 3D molecular orientation. The target P3HT HTL possesses improved charge transport as well as enhanced moisture-repelling capability. Moreover, energy level alignment between target P3HT HTL and perovskite layer is realized. As a result, the champion devices with small (0.04 cm2) and larger areas (1 cm2) deliver notable efficiencies of 20.55% and 18.32%, respectively, which are among the highest efficiency of carbon-electrode PSCs.
RESUMEN
Near-infrared light-emitting diodes (NIR LEDs) based on perovskite quantum dots (QDs) have produced external quantum efficiency (EQE) of ~15 %. However, these high-performance NIR-QLEDs suffer from immediate carrier quenching because of the accumulation of migratable ions at the surface of the QDs. These uncoordinated ions and carriers-if not bound to the nanocrystal surface-serve as centers for exciton quenching and device degradation. In this work, we overcome this issue and fabricate high-performance NIR QLEDs by devising a ligand anchoring strategy, which entails dissolving the strong-binding ligand (Guanidine Hydroiodide, GAI) in the mediate-polar solvent. By employing the dye-sensitized device structure (phosphorescent indicator), we demonstrate the elimination of the interface defects. The treated QDs films exhibit an exciton binding energy of 117â meV: this represents a 1.5-fold increase compared to that of the control (74â meV). We report, as a result, the NIR QLEDs with an EQE of 21 % which is a record among NIR perovskite QLEDs. These QLEDs also exhibit a 7-fold higher operational stability than that of the best previously reported NIR QLEDs. Furthermore, we demonstrate that the QDs are compatible with large-area QLEDs: we showcase 900â mm2 QLEDs with EQE approaching 20 %.
RESUMEN
The power conversion efficiency (PCE) of perovskite solar cells (PSCs) has exceeded those of conventional thin-film solar cell technologies, and the speed at which this increase has been achieved is unprecedented in the history of photovoltaics. Despite the significant progress achieved by PSCs at the laboratory level, their commercial prospects still face two significant challenges: scaling up in size and ensuring long-term stability. Small-area devices (~1 cm2) are typically fabricated using spin-coating. However, this approach may not be suitable for preparing the large-area (>100 cm2) substrates required for commercialization. Thus, new materials and methods must be developed to facilitate the coating of large-area PSCs. This review will discuss the development of scaling up organic-inorganic hybrid PSCs and the challenges of increasing the device area. Furthermore, it will provide an overview of the methodologies for achieving high-efficiency perovskite solar modules.
RESUMEN
The vacuum flash solution method has gained widespread recognition in the preparation of perovskite thin films, laying the foundation for the industrialization of perovskite solar cells. However, the low volatility of dimethyl sulfoxide and its weak interaction with formamidine-based perovskites significantly hinder the preparation of cell modules and the further improvement of photovoltaic performance. In this study, we describe an efficient and reproducible method for preparing large-scale, highly uniform formamidinium lead triiodide (FAPbI3) perovskite films. This is achieved by accelerating the vacuum flash rate and leveraging the complex synergism. Specifically, we designed a dual pump system to accelerate the depressurization rate of the vacuum system and compared the quality of perovskite film formed at different depressurization rates. Further, to overcome the limitations posed by DMSO, we substituted N-methylpyrrolidone as the ligand solvent, creating a stable intermediate complex phase. After annealing, it can be transformed into a uniform and pinhole-free FAPbI3 film. Due to the superior quality of these films, the large area perovskite solar module achieved a power conversion efficiency of 22.7% with an active area of 21.4 cm2. Additionally, it obtained an official certified efficiency of 22.1% with an aperture area of 22 cm2, and it demonstrated long-term stability.
RESUMEN
The efficiency of copper indium gallium selenide (CIGS) solar cells that use transparent conductive oxide (TCO) as the top electrode decreases significantly as the device area increases owing to the poor electrical properties of TCO. Therefore, high-efficiency, large-area CIGS solar cells require the development of a novel top electrode with high transmittance and conductivity. In this study, a microgrid/TCO hybrid electrode is designed to minimize the optical and resistive losses that may occur in the top electrode of a CIGS solar cell. In addition, the buffer layer of the CIGS solar cells is changed from the conventional CdS buffer to a dry-processed wide-band gap ZnMgO (ZMO) buffer, resulting in increased device efficiency by minimizing parasitic absorption in the short-wavelength region. By optimizing the combination of ZMO buffer and the microgrid/TCO hybrid electrode, a device efficiency of up to 20.5% (with antireflection layers) is achieved over a small device area of 5 mm × 5 mm (total area). Moreover, CIGS solar cells with an increased device area of up to 20 mm × 70 mm (total area) exhibit an efficiency of up to 19.7% (with antireflection layers) when a microgrid/TCO hybrid electrode is applied. Thus, this study demonstrates the potential for high-efficiency, large-area CIGS solar cells with novel microgrid electrodes.
RESUMEN
Achieving efficient and large-area organic solar modules via non-halogenated solution processing is vital for the commercialization yet challenging. The primary hurdle is the conservation of the ideal film-formation kinetics and bulk-heterojunction (BHJ) morphology of large-area organic solar cells (OSCs). A cutting-edge non-fullerene acceptor (NFA), Y6, shows efficient power conversion efficiencies (PCEs) when processed with toxic halogenated solvents, but exhibits poor solubility in non-halogenated solvents, resulting in suboptimal morphology. Therefore, in this study, the impact of modifying the inner and outer side-chains of Y6 on OSC performance is investigated. The study reveals that blending a polymer donor, PM6, with one of the modified NFAs, namely N-HD, achieved an impressive PCE of 18.3% on a small-area OSC. This modified NFA displays improved solubility in o-xylene at room temperature, which facilitated the formation of a favorable BHJ morphology. A large-area (55 cm2) sub-module delivered an impressive PCE of 12.2% based on N-HD using o-xylene under ambient conditions. These findings underscore the significant impact of the modified Y6 derivatives on structural arrangements and film processing over a large-area module at room temperature. Consequently, these results are poised to deepen the comprehension of the scaling challenges encountered in OSCs and may contribute to their commercialization.
RESUMEN
Perovskite light-emitting diodes (PeLEDs) that can be air-processed promises the development of displaying optoelectronic device, while is challenged by technical difficulty on both the active layer and hole transport layer (HTL) caused by the unavoidable humidity interference. Here, we propose and validate that, planting the polymer brush with tailored functional groups in inorganic HTL, provides unique bilateral embedded anchoring that is capable of simultaneously addressing the n phases crystallization rates in the active layer as well as the deteriorated particulate surface defects in HTL. Exemplified by zwitterionic polyethyleneimine-sulfonate (PEIS) in present study, its implanting in NiOx HTL offers abundant nuclei sites of amino and sulfonate groups that balance the growth rate of different n phases in quasi-2D perovskite films. Moreover, the PEIS effectively nailed the interfacial contact between perovskite and NiOx, and reduced the particulate surface defects in HTL, leading to the enhanced PLQY and stability of large-area blue perovskite film in ambient air. By virtue of these merits, present work achieves the first demonstration of the air-processed blue PeLEDs in large emitting area of 1.0 cm2 with peak external quantum efficiency (EQE) of 2.09 %, which is comparable to the similar pure-bromide blue PeLEDs fabricated in glovebox.
RESUMEN
Perovskite solar cells (PSCs) have led to distinguished achievements and become one of the state-of-the-art photovoltaic technologies. Undoubtedly, reliable preparation of large area high-quality perovskite (PVK) films with uniform optoelectronic properties has become a critical and challenging task to transition PSCs from lab to market. Here, methyldiphenylphosphine oxide (MDPPO) is employed as an additive in a PVK precursor solution to promote uniform conductivity and carrier transport of PVK films. More important, to check its compatibility with the upscaling process, the MDPPO additive strategy was further applied to doctor-blade large-area PVK films. As a result, benefit from the favorable role of MDPPO additive, the power conversion efficiencies (PCEs) of small-area PSCs reach 23.85% with superb open circuit voltage (Voc) of 1.15 V and fill factor of 81.21%, while an impressive PCE of 19.22% was achieved for the large-area PSC minimodules with active area of 61.48 cm2. Remarkably, the MDPPO modified device exhibits significantly improved operational stability, maintaining an initial efficiency of 68% even after 750 h under continuous 1-sun illumination. Our achievements will provide profound insight and further guidance for the scale-up process of PSCs from lab to large-scale modules.
RESUMEN
Bifunctional electrode materials are highly desirable for meeting increasing global energy demands and mitigating environmental impact. However, improving the atom-efficiency, scalability, and cost-effectiveness of storage systems, as well as optimizing conversion processes to enhance overall energy utilization and sustainability, remains a significant challenge for their application. Herein, we devised an optimized, facile, economic, and scalable synthesis of large area (cm2), ultrathin (â¼2.9 ± 0.3 nm) electroactive nanosheet of ß-Ni(OH)2, which acted as bifunctional electrode material for charge storage and oxygen evolution reaction (OER). The ß-Ni(OH)2 nanosheet electrode shows the volumetric capacity of 2.82 Ah.cm-3(0.82 µAh.cm-2) at the current density of 0.2 mA.cm-2. The device shows a high capacity of 820 mAh.cm-3 with an ultrahigh volumetric energy density of 0.33 Wh.cm-3 at 275.86 W.cm-3 along with promising stability (30,000 cycles). Furthermore, the OER activity of ultrathin ß-Ni(OH)2 exhibits an overpotential (η10) of 308 mV and a Tafel value of 42 mV dec-1 suggesting fast reaction kinetics. The mechanistic studies are enlightened through density functional theory (DFT), which reveals that additional electronic states near the Fermi level enhance activity for both capacitance and OER.
RESUMEN
Nanostructures with sufficiently large areas are necessary for the development of practical devices. Current efforts to fabricate large-area nanostructures using step-and-repeat nanoimprint lithography, however, result in either wide seams or low efficiency due to ultraviolet light leakage and the overflow of imprint resin. In this study, we propose an efficient method for large-area nanostructure fabrication using step-and-repeat nanoimprint lithography with a composite mold. The composite mold consists of a quartz support layer, a soft polydimethylsiloxane buffer layer, and multiple intermediate polymer stamps arranged in a cross pattern. The distance between the adjacent stamp pattern areas is equal to the width of the pattern area. This design combines the high imprinting precision of hard molds with the uniform large-area imprinting offered by soft molds. In this experiment, we utilized a composite mold consisting of three sub-molds combined with a cross-nanoimprint strategy to create large-area nanostructures measuring 5 mm × 30 mm on a silicon substrate, with the minimum linewidth of the structure being 100 nm. Compared with traditional step-and-flash nanoimprint lithography, the present method enhances manufacturing efficiency and generates large-area patterns with seam errors only at the micron level. This research could help advance micro-nano optics, flexible electronics, optical communication, and biomedicine studies.
RESUMEN
Organic solar cells (OSCs) are one of the most promising photovoltaic technologies due to their affordability and adaptability. However, upscaling is a critical issue that hinders the commercialization of OSCs. A significant challenge is the lack of cost-effective and facile techniques to modulate the morphology of the active layers. The slow solvent evaporation leads to an unfavorable phase separation, thus resulting in a low power conversion efficiency (PCE) of organic solar modules. Here, a nitrogen-blowing assisted method is developed to fabricate a large-area organic solar module (active area = 12 cm2) utilizing high-boiling-point solvents, achieving a PCE of 15.6%. The device fabricated with a high-boiling-point solvent produces a more uniform and smoother large-area film, and the assistance of nitrogen-blowing accelerates solvent evaporation, resulting in an optimized morphology with proper phase separation and finer aggregates. Moreover, the device fabricated by the nitrogen-blowing assisted method exhibits improved exciton dissociation, balanced carrier mobility, and reduced charge recombination. This work proposes a universal and cost-effective technique for the fabrication of high-efficiency organic solar modules.
RESUMEN
Nonlead low-dimensional halide perovskites attract considerable attention as X-ray scintillators. However, most scintillation screens exhibit pronounced light scattering, which detrimentally reduces the quality of X-ray imaging. Herein, we employed a simple and straightforward solvent-free melt-quenching method to fabricate a large-area zero-dimension (0D) antimony-based perovskite transparent medium, namely (C20H20P)2SbCl5 (C20H20P+ = ethyltriphenylphosphine). The transparency is due to the large steric hindrance of C20H20P+, which hinders the formation of crystals during the quenching process, thus forming a glass with low refractive index and uniform structure. This medium exhibits a high transmittance exceeding 80% in the range of 450-800 nm and shows a large Stokes shift of 245 nm, thereby minimizing light scattering, mitigating self-absorption, and enhancing the clarity of X-ray imaging. Moreover, it exhibits a high radioluminescence light yield of â¼12,535 photons MeV-1 and displays a high X-ray spatial resolution of 30 lp mm-1 owing to its high transparency. This study presents an alternative candidate for achieving high-quality X-ray detection and extends the applicability of transparent perovskite scintillators.
RESUMEN
Asymmetric non-fullerene small molecules acceptor (as-NF-SMAs) exhibit greater vitality in photovoltaic materials compared to their symmetric counterparts due to their larger dipole moments and stronger intermolecular interactions, which facilitate exciton dissociation and charge transmission in organic solar cells (OSCs). Here, we introduced a new as-NF-SMAs, named IDT-TNIC, as the third component in ternary organic solar cells (TOSCs). The asymmetric IDT-TNIC used indacenodithiophene (IDT) as the central core, alkylthio-thiophene as a unilateral π-bridge and extended end groups as electron-withdrawing. Due to the non-covalent conformational lock (NCL) established between Oâ â â S and Sâ â â S, the IDT-TNIC molecule preserves its coplanar structure effectively. Furthermore, IDT-TNIC exhibits complementary absorption and excellent compatibility with donor and acceptor materials, as well as optimized ladder energy level arrangement, resulting in a higher and more balanced µh/µe value, more homogeneous and suitable phase separation morphology in TOSCs. Thus, the PCE of the TOSCs reached 17 % when the weight ratio of PM6 : Y6 : IDT-TNIC was 1 : 1.1 : 0.1, and it is noteworthy that when the device area was increased to 1â cm2, the PCE could still be maintained at over 14 %. Detailed studies and analysis indicate that IDT-TNIC has great potential as a third component in OSCs and for large-scale printing in the future.
RESUMEN
Ternary copper (Cu) halides are promising candidates for replacing toxic lead halides in the field of perovskite light-emitting diodes (LEDs) toward practical applications. However, the electroluminescent performance of Cu halide-based LEDs remains a great challenge due to the presence of serious nonradiative recombination and inefficient charge transport in Cu halide emitters. Here, the rational design of host-guest [dppb]2Cu2I2 (dppb denotes 1,2-bis[diphenylphosphino]benzene) emitters and its utility in fabricating efficient Cu halide-based green LEDs that show a high external quantum efficiency (EQE) of 13.39% are reported. The host-guest [dppb]2Cu2I2 emitters with mCP (1,3-bis(N-carbazolyl)benzene) host demonstrate a significant improvement of carrier radiative recombination efficiency, with the photoluminescence quantum yield increased by nearly ten times, which is rooted in the efficient energy transfer and type-I energy level alignment between [dppb]2Cu2I2 and mCP. Moreover, the charge-transporting mCP host can raise the carrier mobility of [dppb]2Cu2I2 films, thereby enhancing the charge transport and recombination. More importantly, this strategy enables a large-area prototype LED with a record-breaking area up to 81 cm2, along with a decent EQE of 10.02% and uniform luminance. It is believed these results represent an encouraging stepping stone to bring Cu halide-based LEDs from the laboratory toward commercial lighting and display panels.
RESUMEN
Film formation kinetics significantly impact molecular processability and power conversion efficiency (PCE) of organic solar cells. Here, two ternary random copolymerization polymers are reported, D18âN-p and D18âN-m, to modulate the aggregation ability of D18 by introducing trifluoromethyl-substituted pyridine unit at para- and meta-positions, respectively. The introduction of pyridine unit significantly reduces material aggregation ability and adjusts the interactions with acceptor L8-BO, thereby leading to largely changed film formation kinetics with earlier phase separation and longer film formation times, which enlarge fiber sizes in blend films and improve carrier generation and transport. As a result, D18âN-p with moderate aggregation ability delivers a high PCE of 18.82% with L8-BO, which is further improved to 19.45% via interface engineering. Despite the slightly inferior small area device performances, D18âN-m shows improved solubility, which inspires to adjust the ratio of meta-trifluoromethyl pyridine carefully and obtain a polymer donor D18âN-m-10 with good solubility in nonhalogenated solvent o-xylene. High PCEs of 13.07% and 12.43% in 1 cm2 device and 43 cm2 module fabricated with slot-die coating method are achieved based on D18âN-m-10:L8-BO blends. This work emphasizes film formation kinetics optimization in device fabrication via aggregation ability modulation of polymer donors for efficient devices.
RESUMEN
Reducing the defect density of perovskite films during the crystallization process is critical in preparing high-performance perovskite solar cells (PSCs). Here, a multi-functional molecule, 3-phenyl-4-aminobutyric acid hydrochloride (APH), with three functional groups including a benzene ring, âNH3 + and âCOOH, is added into the perovskite precursor solution to improve perovskite crystallization and device performance. The benzene ring increases the hydrophobicity of perovskites, while âNH3 + and âCOOH passivate defects related to I- and Pb2+, respectively. Consequently, the power conversion efficiency (PCE) of the optimal device increased to 24.65%. Additionally, an effective area of 1 cm2 with a PCE of 22.45% is also prepared using APH as an additive. Furthermore, PSCs prepared with APH exhibit excellent stability by 87% initial PCE without encapsulation after exposure at room temperature under 25% humidity for 5000 h and retaining 70% of initial PCE after aging at 85 °C in an N2 environment for 864 h.