RESUMEN
Al-Mg alloys are widely used as important engineering structural materials in aerospace engineering, transportation systems, and structural constructions due to their low density, high specific strength, corrosion resistance, welding capability, fatigue strength, and cost-effectiveness. However, the conventional Al-Mg alloys can no longer fully satisfy the demands of practical production due to difficulties caused by many defects. The high strength of Al-Mg alloys as non-heat treatment precipitation-strengthened alloys is achieved primarily by solid solution strengthening along with work hardening rather than precipitation strengthening. Therefore, severe plastic deformation (SPD) techniques can be often used to produce ultrafine-grained structures to fabricate ultra-high strength aluminum alloys. However, this approach often achieves the strengthening of material at the cost of reduced ductility. This paper comprehensively summarizes the various approaches of ultrafine/nanocrystalline materials for enhancing their plasticity, elaborates on the creation of a bimodal microstructure within the alloy, and discusses the formation of a nanotwin microstructure within the alloy and the incorporation of dispersed nanoparticles. The mechanisms underlying both the strengthening and toughening during large plastic deformation in aluminum alloys are summarized, and the future research direction of high-performance ultrafine crystalline and nanocrystalline Al-Mg aluminum alloys is prospected.
RESUMEN
Extended exposure to seawater results in the erosion of the structural high-strength steels utilized in marine equipment, primarily due to the infiltration of hydrogen. Consequently, this erosion leads to a decrease in the mechanical properties of the material. In this investigation, the mechanical responses of Q690 structural high-strength steel specimens were investigated by considering various hydrogen charging parameters, such as the current density, charging duration, and solution concentration values. The findings highlighted the significant impacts of electrochemical hydrogen charging parameters on the mechanical behaviors of Q690 steel samples. Specifically, a linear relationship was observed between the mechanical properties and the hydrogen charging current densities, while the associations with the charging duration and solution concentration were nonlinear. Additionally, the fracture morphology under various hydrogen charging parameters was analyzed and discussed. The results demonstrate that the mechanical properties of the material degrade with increasing hydrogen charging parameters, with tensile strength and yield stress decreasing by approximately 2-4%, and elongation after fracture reducing by about 20%. The findings also reveal that macroscopic fractures exhibit significant necking in uncharged conditions. As hydrogen charging parameters increase, macroscopic necking gradually diminishes, the number of microscopic dimples decreases, and the material ultimately transitions to a fully brittle fracture.
RESUMEN
Hydrogen fuel holds promise for clean energy solutions, particularly in onboard applications such as fuel cell vehicles. However, the development of efficient hydrogen storage systems remains a critical challenge. This study addresses this challenge by exploring the potential of high-strength novel materials, including glass, to maximize onboard hydrogen storage capacity. A mathematical approach was employed to evaluate the feasibility and efficacy of various high-strength materials for hydrogen storage. This study focused on capillary arrays as a promising storage medium and utilized mathematical modeling techniques to estimate the storage capacity enhancement achievable with different materials. The analysis revealed significant variations in storage capacity enhancements in different high-strength novel materials, with glass having promising results. Glass-based materials demonstrated the potential to meet or exceed US Department of Energy (DOE) targets for both gravimetric and volumetric hydrogen storage capacities in capillary arrays. By leveraging a mathematical approach, this study identified high-strength novel materials, including glass and polymers, capable of substantially improving onboard hydrogen storage capacity: 29 wt.% with 40 g/L for quartz glass and 25 wt.% with 38 g/L for Kevlar compared to 5.2 wt.% with 26.3 g/L from a conventional type IV tank. These findings underscore the importance of material selection in optimizing hydrogen storage systems and provide valuable insights for the design and development of next-generation hydrogen storage technologies for onboard applications.
RESUMEN
Welding experiments were conducted under different currents for single-pass butt welding of high-strength steel flat plates. The microstructure of welded joints was characterized using OM, SEM, and EBSD, and the welding process was numerically simulated using a finite element method. According to the grain size obtained by electron microscope characterization and the temperature data obtained by simulation, the microstructure and mechanical properties of coarse grain and fine grain areas of the heat-affected zone were predicted by using the material microstructure and property simulation software. Finally, the results of mechanical properties simulation were verified through mechanical property testing.
RESUMEN
In this study, a UV-cured collagen-based film (C-P-H film) with high mechanical strength and antimicrobial properties was developed by riboflavin-mediated ultraviolet irradiation of collagen solution containing histidine-modified ε-polylysine. Fourier transform infrared analysis indicated that covalent cross-linking was formed between the collagen molecule and the histidine-grafted ε-polylysine. Compared with the pure collagen film, the C-P-H film containing 5 wt% histidine-modified ε-polylysine showed higher tensile strength (145.98 MPa), higher thermal denaturation temperature (76.5 °C), lower water vapor permeability (5.54 × 10-11 g m-1 s-1 Pa) and excellent antimicrobial activities against Escherichia coli and Staphylococcus aureus. In addition, the wrapping of the C-P-H film effectively inhibited bacterial growth of pork during storage time, successfully prolonging the shelf-life of pork by approximately 4 days compared to that of plastic wrap. These results suggested that collagen-based film grafted with histidine-modified ε-polylysine via riboflavin-mediated ultraviolet irradiation process had a great potential for pork preservation.
Asunto(s)
Colágeno , Escherichia coli , Embalaje de Alimentos , Conservación de Alimentos , Polilisina , Riboflavina , Staphylococcus aureus , Rayos Ultravioleta , Riboflavina/química , Riboflavina/farmacología , Animales , Colágeno/química , Colágeno/farmacología , Polilisina/química , Polilisina/farmacología , Escherichia coli/efectos de los fármacos , Escherichia coli/crecimiento & desarrollo , Staphylococcus aureus/efectos de los fármacos , Staphylococcus aureus/crecimiento & desarrollo , Porcinos , Embalaje de Alimentos/instrumentación , Conservación de Alimentos/instrumentación , Conservación de Alimentos/métodos , Resistencia a la Tracción , Antibacterianos/farmacología , Antibacterianos/química , Antiinfecciosos/farmacología , Antiinfecciosos/químicaRESUMEN
Lost circulation is a common and complicated situation in drilling engineering. Serious lost circulation may lead to pressure drop in the well, affect normal drilling operations, and even cause wellbore instability, formation fluid flooding into the wellbore, and blowout. Therefore, appropriate preventive and treatment measures need to be taken to ensure the safe and smooth operation of drilling operations. So, it is necessary to conduct in-depth research on the development and performance of the plugging materials. In this study, urea formaldehyde resin with high temperature resistance and strength was used as the main raw material, and the curing conditions were optimized and adjusted by adding a variety of additives. The curing time, compressive strength, temperature resistance, and other key performance indexes of the resin plugging agent were studied, and a resin plugging agent system with excellent plugging performance was prepared. The formula is as follows: 25% urea formaldehyde resin +1% betaine +1% silane coupling agent KH-570 + 3% ammonium chloride +1% hexamethylenetetramine +1% sodium carboxymethyl cellulose. The optimal curing temperature is between 60 and 80 °C, with a controllable curing time of 1-3 h. Experimental studies examined the rheological and curing properties of the resin plugging agent system. The results showed that the viscosity of the high-strength curable resin system before curing remained stable with increasing shear rates. Additionally, the storage modulus and loss modulus of the resin solutions increased with shear stress, with the loss modulus being greater than the storage modulus, indicating a viscous fluid. The study also investigated the effect of different salt ion concentrations on the curing effect of the resin plugging system. The results showed that formation water containing Na+ at concentrations between 500 mg/L and 10,000 mg/L increased the resin's curing strength and reduced curing time. However, excessively high concentrations at lower temperatures reduced the curing strength. Formation water containing Ca2+ increased the curing time of the resin plugging system and significantly impacted the curing strength, reducing it to some extent. Moreover, the high-strength curable resin plugging agent system can effectively stay in various fracture types (parallel, wedge-shaped) and different fracture sizes, forming a high-strength consolidation under certain temperature conditions for effective plugging. In wedge-shaped fractures with a width of 10 mm, the breakthrough pressure of the high-strength curable resin plugging agent system reached 8.1 MPa. As the fracture width decreases, the breakthrough pressure increases, reaching 9.98 MPa in wedge-shaped fractures with an outlet fracture width of 3 mm, forming a high-strength plugging layer. This research provides new ideas and methods for solving drilling fluid loss in fractured loss zones and has certain application and promotion value.
RESUMEN
OBJECTIVE: To compare the clinical efficacy of ligament advanced reinforcement system (LARS) and autogenous hamstring tendon plus high-strength suture in arthroscopic reconstruction of posterior cruciate ligament(PCL). METHODS: A total of 96 patients with simple PCL injury treated with arthroscopic posterior cruciate ligament reconstructive surgery admitted to our hospital between August 2019 and December 2021 were selected for complete follow-up. There were 78 males and 18 females, 40 cases of left leg and 56 cases of right leg, the aged from 20 to 56 years old with an average of (32.50±8.68 ) years old. The transplants were divided into two groups:LARS group (52 cases) and autogenous hamstring tendon plus high-strength suture group (44 cases). In the LARS group, there were 42 males and 10 females;with an average age of (31.84±8.62) years old;body mass index (BMI) was (24.73±2.29) kgï¹m-2;7 mm LARS was used to reconstruct PCL. In the autologous tendon group, there were 36 males and 8 females, with an average age of (33.06±8.99) years old, BMI was (23.52±2.16) kg·m-2, and the PCL was reconstructed with four strands of hamstring tendons and three pieces of Ethibond suture. All patients underwent functional rehabilitation guided exercise and were followed up regularly after surgery to objectively evaluate the stability of the knee joint by KT-1000 measurement of knee relaxation, and subjective evaluation of knee function by Lysholm score, Tegner score, and International Knee Documentation Council (IKDC) score. Data from preoperative, 3, 6, and 12 month follow-up were collected and analyzed by SPSS software to compare postoperative recovery and ligament relaxation between the two groups of patients. RESULTS: Ninety-six patients were followed up for 12 months. KT-1000 measurement of knee joint in autogenous tendon group and LARS group before operation [(10.73±1.46) points vs (10.55±1.53) points], 6 months after operation[(3.02±0.75) points vs (2.35±0.60) points], 12 months after operation[(3.77±1.76) points vs (2.44±0.60) points]. There was significant difference between the two groups at 6 and 12 months after operation (P<0.05), but there was no significant difference between the two groups at 3 months after operation (P>0.05). In the autogenous tendon group and LARS group, before operation and 12 months after operation, total Lysholm score [(40.6±16.8), (91.25±6.35) points vs (51.92±18.52), (92.35±5.30) points], Tegner score[(1.8±0.7), (5.8±0.6) points vs(1.7±0.8)ã(5.7±0.7) points] and total IKDC score[(54.50±6.33), (83.90±3.93) points vs (54.40±4.24), (83.62±3.64) points], the differences were statistically significant (P<0.05), indicating that the knee function of the two groups was improved after surgery. At 3 and 6 months after operation in the autogenous tendon group and LARS group, the total Lysholm score[(65.86±11.54), (74.60±6.46) points vs (73.46±6.42), (86.73±4.62) points], Tegner score[(2.5±0.6), (3.5±0.5) points vs (4.3±0.7), (5.0±1.4) points], the total scores of IKDC [(55.78±2.68), (70.62±4.74) points vs (65.31±4.60), (79.71±2.93) points]. The difference between two groups was statistically significant (P<0.05). The results showed that the function of the knee joint in the LARS group was better than that the autologous tendon group. However, at 12 months after the operation, there was no significant difference in the score of knee joint function between the two groups (P>0.05). The results showed that the stability of LARS group was better than that of autologous tendon group. CONCLUSION: Both the autogenous hamstring tendon plus high-strength suture and LARS reconstruction can significantly improve the knee function and stability, with satisfactory postoperative results. Howervr the LARS provides superior postoperative stability.
Asunto(s)
Tendones Isquiotibiales , Reconstrucción del Ligamento Cruzado Posterior , Ligamento Cruzado Posterior , Humanos , Masculino , Femenino , Adulto , Persona de Mediana Edad , Tendones Isquiotibiales/trasplante , Reconstrucción del Ligamento Cruzado Posterior/métodos , Adulto Joven , Ligamento Cruzado Posterior/cirugía , Ligamento Cruzado Posterior/lesiones , Suturas , Trasplante Autólogo , Resultado del TratamientoRESUMEN
In this study, multifibrillar carbon and carbon/ceramic (C/SiCON) fibers consisting of thousands of single nanofibers are continuously manufactured. The process starts with electrospinning of polyacrylonitrile (PAN) and PAN/oligosilazane precursors resulting in poorly aligned polymer fibers. Subsequent stretching leads to parallel aligned multifibrillar fibers, which are continuously stabilized and pyrolyzed to C or C/SiCON hybrid fibers. The multifibrillar carbon fibers show a high tensile strength of 911 MPa and Young's modulus of 154 GPa, whereas the multifibrillar C/SiCON fibers initially have only tensile strengths of 407 MPa and Young's modulus of 77 GPa, due to sticking of the nanofibers during the stabilization in air. Additional curing with electron beam radiation, results in a remarkable increase in tensile strength of 707 MPa and Young's modulus of 98 GPa. The good mechanical properties are highlighted by the low linear density of the multifibrillar C/SiCON fibers (~ 1 tex) compared to conventional C and SiC fiber bundles (~ 200 tex). In combination with the large surface area of the fibers better mechanical properties of respective composites with a reduced fiber content can be achieved. In addition, the developed approach offers high potential to produce advanced endless multifibrillar carbon and C/SiCON nanofibers in an industrial scale.
RESUMEN
Steel fiber reinforced high-strength concrete (SFRHSC) is a composite material composed of cement, coarse aggregate, and randomly distributed short steel fibers. The excellent tensile strength of steel fiber can significantly improve the crack resistance and ductility of high-strength concrete (HSC). In this study, experimental and numerical investigations were performed to study the cyclic behavior of the HSC beam-column joint. Three SFRHSC and one HSC beam-column joint were prepared and tested under cyclic load. Two different volume ratios of steel fibers and three stirrups ratios in the joint core area were experimentally studied. After verification of the experimental results, numerical simulations were further carried out to investigate the influence of steel fibers volume ratio and stirrups ratio in the joint core area on the seismic performance. Evaluation of the hysteretic response, ductility, energy dissipation, stiffness, and strength degradation were the main aims of this study. Results indicate that the optimal volume fraction of steel fibers is 1.5%, and the optimal stirrups ratio in the joint core area is 0.9% in terms of the enhancement of the seismic performance of the SFRHSC beam-column joint.
RESUMEN
Recently, certain challenges and accompanying drawbacks have emerged in the preparation of high-strength and tough polymer hydrogels. Insights from wood science highlight the role of the intertwined molecular structure of lignin and crystalline cellulose in contributing to wood's strength. Herein, we immersed prestretched poly(vinyl alcohol) (PVA) polymer hydrogels into a solution of nanosized lignosulfonate sodium (LS), a water-soluble anionic polyelectrolyte, to creatively reconstruct this similar structure at the molecular scale in hydrogels. The nanosized LS effectively fixed and bundled the prestretched PVA polymers while inducing the formation of dense crystalline domains within the polymer matrix. Consequently, the interwoven structure of crystalline PVA and LS conferred good strength to the composite hydrogels, exhibiting a tensile strength of up to â¼23 MPa, a fracture strain of â¼350%, Young's modulus of â¼17 MPa, toughness of â¼47 MJ/m3, and fracture energy of â¼42 kJ/m2. This hydrogel far outperformed previous hydrogels composed directly of lignin and PVA (tensile strength <1.5 MPa). Additionally, the composite hydrogels demonstrated excellent antifreezing properties (<-80 °C). Notably, the LS-assisted reconstruction technology offers opportunities for the secondary fixation of PVA hydrogel shapes and high-strength welding of hydrogel components. This work introduces an approach for the high-value utilization of LS, a green byproduct of pulp production. LS's profound biomimetic strategy will be applied in multifunctional hydrogel fields.
RESUMEN
Polyimide (PI) aerogels have various applications in aerospace, national defense, military industry, and rail transit equipment. This paper reports a series of ultra-lightweight, high elasticity, high strength, low thermal conductivity, and high flame retardant rGO/PI nanocomposite aerogels prepared by the ice templating method. The effects of freezing processes (unidirectional freezing and random freezing), chemical composition, and environmental temperature (-196-200 °C) on the morphology, mechanical, and thermal properties of the aerogels were systematically studied. The results indicated that unidirectional aerogels exhibit anisotropic mechanical properties and thermal performance. Compression in the horizontal direction showed high elasticity, high fatigue resistance, and superior thermal insulation. Meanwhile, in the vertical direction, it demonstrated high strength (PI-G-9 reaching 14 MPa). After 10,000 cycles of compression in the horizontal direction (at 50 % strain), the unidirectional PI-G-5 aerogel still retains 90.32 % height retention, and 78.5 % stress retention, and exhibited a low stable energy loss coefficient (22.11 %). It also possessed a low thermal conductivity (32.8 mW m-1 K-1) and demonstrated good thermal insulation performance by sustaining at 200 °C for 30 min. Interestingly, the elasticity of the aerogels was enhanced with decreasing temperatures, achieving a height recovery rate of up to 100 % when compressed in liquid nitrogen. More importantly, the rGO/PI aerogels could be utilized over a wide temperature range (-196-200 °C) and had a high limiting oxygen index (LOI) ranging from 43.3 to 48.1 %. Therefore, this work may provide a viable approach for designing thermal insulation and flame-retardant protective materials with excellent mechanical properties that are suitable for harsh environments.
RESUMEN
While Portland cement produces large amounts of carbon dioxide, low-calcium high-strength cements effectively reduce carbon emissions by decreasing the proportion of high-calcium minerals. In order to enhance the practical application value of low-calcium high-strength cement, the effects of mineral admixtures on the chloride binding capacity and pore structure characteristics of low-calcium high-strength cement pastes were investigated by equilibrium method and mercury intrusion method. The results showed that the chloride binding capacity of low-calcium high-strength cement pastes is superior to that of Portland cement. Fly ash and slag enhance this capacity by promoting monosulfoaluminate and C-S-H gel formation, with fly ash being more effective. Ground limestone also boosts chloride binding when incorporated at less than 10 wt%. However, sulfates have a more significant negative impact on chloride binding capacity in low-calcium high-strength cement pastes compared to Portland cement. The porosity of low-calcium high-strength cement pastes exhibits contrasting trends with the addition of fly ash, ground limestone, and slag. Fly ash and limestone initially coarsen the pore structure but later facilitate the transition of larger pores to smaller ones. In contrast, slag initially has little impact but later promotes the conversion of large capillary pores to medium ones, optimizing the pore structure. Notably, above 10 wt% fly ash, the critical pore diameter decreases with additional fly ash except at 10% where it increases for 3 days. Ground limestone enlarges the critical pore diameter, and this effect intensifies with higher content. During early hydration, slag decreases the critical pore diameter, but its impact diminishes in later stages.
RESUMEN
Cold bending forming is a complex forming process, and its product quality is closely related to the forming process parameters. To mitigate issues such as bulging and waviness arising from the extension of the material at the edges during the forming process of thin-walled circular tubes, a comprehensive comparative analysis was conducted on four forming methods. This analysis determined that the combined bending method is the optimal forming technique for the equipment. For the impact of different parameters on the equivalent plastic strain distribution of the product and the force on the rollers, numerical simulations were carried out using the software COPRA (COPRA FEA RF 2023.1) after designing the pattern diagram based on the integrated bending method. The results showed that different processing speeds on the equivalent plastic strain distribution and work hardening of the plate have little effect. As the spacing between the upper and lower rollers increases, the equivalent plastic strain of the plate to a certain extent and the value of the moment of the rollers is significantly reduced. Analyzing the performance characteristics of high-strength steel materials from the aspects of the thickness strain and cross-sectional forming of the plate, this verifies the advantages of forming high-strength steel plates. The numerical simulation results of this study are in good agreement with actual production experimental results.
RESUMEN
Synergistic strengthening of nano-scaled M2C and ß-NiAl has become a new route to develop ultra-high secondary-hardening steel. At present, the effect of Co on the synergistic precipitation behavior of duplex phases of M2C and ß-NiAl has been rarely reported. This paper revealed the effects of Co on the mechanical properties and duplex precipitates of M2C and ß-NiAl in a novel 2.5 GPa ultra-high strength secondary-hardening steel. The tensile tests indicated that a 10% Co-alloy steel achieved a much stronger secondary-hardening effects compared to a Co-free steel during aging process, especially in the early-aging state. Needle-shaped M2C and spherical ß-NiAl particles were observed in both Co-alloy and Co-free steels. However, the number density, and volume fraction of M2C were significantly enhanced in the 10% Co-alloy steel. The Mo contents in M2C carbide and α-Fe after aging treatment were both analyzed through experimental determination and thermodynamic calculation, and the results indicated that Co decreased the solubility of Mo in α-Fe, thus promoting the precipitation of Mo-rich carbides.
RESUMEN
Extrusion-based 3D printing is a facile technology to construct complex structures of hydrogels, especially for tough hydrogels that have shown demonstrated potential in load-bearing materials and tissue engineering. However, 3D-printed hydrogels often possess mechanical properties that do not guarantee their usage in tissue-mimicking, load-bearing components, and motion sensors. This study proposes a novel strategy to construct high-strength and anisotropic Fe3+ cross-linked poly(acrylamide-co-acrylic acid)/sodium alginate double network hydrogels. The semi-flexible sodium alginate chains act as a "conformation regulator" to promote the formation of strong intermolecular interactions between polymer chains and lock the more extended conformation exerted by the pre-stretch, enabling the construction of 3D-printed hydrogel structures with high orientation. The equilibrated anisotropic hydrogel filaments with a water content of 50-60 wt.% exhibit outstanding mechanical properties (tensile strength: 9-44 MPa; elongation at break: 120-668%; Young's modulus: 7-62 MPa; toughness: 26-52 MJ m- 3). 3D-printed anisotropic hydrogel structures with high mechanical performance show demonstrated potential as loading-bearing structures and electrodes of flexible triboelectric nanogenerators for versatile human motion sensing.
RESUMEN
A laboratory-scale mesophilic submerged anaerobic hybrid membrane bioreactor (An-HMBR) was operated for 270 days for the treatment of high-strength synthetic wastewater at different hydraulic retention times (HRTs) (3 days, 2 days, 1 day, and 0.5 days). Chemical oxygen demand (COD) removal efficiency of 92% was obtained with methane yield rate of 0.18 LCH4/g CODremoval at 1-day HRT. The results of lab scale reactor at 1-day HRT were utilized for upscaling and cost analysis. Cost analysis revealed that the total capital cost comprised tank system (48%), membrane cost (32%), screen and PUF sponge (5% each), PLCs (4%), liquid pumps (3%), and others (2%). The operational cost comprised chemical cost (46%), pumping energy (42%), and sludge disposal (12%). The results revealed that the tank and heating costs accounted for the largest fraction of the total life cycle cost for full-scale An-HMBR. The heating cost can be compensated by gas recovery. Sensitivity analysis revealed that the interest rates, influent flow, and membrane flux were the most crucial parameters which affected the total cost of An-HMBR.
Asunto(s)
Reactores Biológicos , Eliminación de Residuos Líquidos , Anaerobiosis , Eliminación de Residuos Líquidos/métodos , Temperatura , Aguas Residuales , Análisis de la Demanda Biológica de Oxígeno , Membranas Artificiales , Aguas del AlcantarilladoRESUMEN
Facing the severe problem of microplastic pollution, there is an urgent need to develop biodegradable fibers to replace the petrochemical fibers. Sodium alginate, a biomass polysaccharide, has gained widespread attentions recently for the fiber manufacture. However, the limited mechanical strength of alginate fibers restricts their usages as load-bearing fabrics and reinforcement fibers. Here, we develop a novel strategy to prepare alginate multifilaments using pre-crosslinked sodium alginate solutions. The increase in the pre-crosslinking ratio effectively hinders the disentanglement of sodium alginate chains at high stretches, causing an increase in the shear viscosity of the solution ascertained from the capillarity-driven thinning process from 4.5 Pa·s to 9.9 Pa·s and facilitating the high alignment and orientation of sodium alginate chains. The resultant fibers possess a breaking strength of 474 MPa, elongation at break of 16 %, Young's modulus of 14.4 GPa, and toughness of 51.8 MJ/m3, exceeding most biomass fibers without reinforcement additives. The high orientation degree of 0.865 and high spinnability of alginate multifilaments enable their applications in multi-channel encryption fabrics that exhibit distinct information under various optical conditions. This rheological regulation of spinning solutions provides a facile yet effective strategy to enhance the mechanical performance and broaden application scenarios of alginate fibers.
RESUMEN
The literature on polyvinyl alcohol (PVA) films is extensive, however, these methods often necessitate intricate synthesis processes or the addition of plasticizers to modify the strength and water solubility of the PVA material. A high-strength UV radiation-resistant composite film by chelating Fe3+ with lignin and PVA, which exhibits excellent hydrolysis resistance is developed. This composite film is prepared simply by incorporating a small amount of dealkalized lignin (APPL) and ferric chloride (FeCl3) into PVA through a straightforward composite process. During the scanning test, it is noted that the film exhibits a high density of uniformly dispersed particles, endowing it with efficient ultraviolet absorption capabilities. The infrared and anti-dissolution tests reveal that the coordination of Fe3+ with lignin imparts an outstanding hydrolysis resistance to the film, obviating the need for any extender, curing agent, acid or base. The tensile fracture strength reaches an impressive 187.81Mpa in the tensile test. UV and indicator card tests unequivocally demonstrate that the film achieves a remarkable 100% anti-UV efficiency. This Fe3+ chelated lignin/PVA composite film, with its facile preparation, environmental sustainability, high strength, and outstanding anti-ultraviolet efficiency, can be deployed across diverse applications requiring robust protection against ultraviolet radiation.
RESUMEN
Anti-swelling conductive hydrogels with simultaneous high tensile strength (>1 MPa) and fast self-recovery are promising candidates for underwater strain sensing, but their preparation remains challenging. Herein, novel anti-swelling conductive nanocomposite hydrogels were fabricated based on poly(acrylamide-co-acrylic acid) (P(AM-co-AA)), polymer-grafted cellulose nanocrystals (CNCs) and Fe3+ ions through a strategy combining nano-reinforcing and multiple physical crosslinking. Due to the presence of interfacial H-bonds, polymer-grafted cellulose nanocrystals played important role in endowing hydrogels with anti-swelling capacity and enhanced mechanical performance. The obtained nanocomposite hydrogels exhibited relatively low swelling ratio (2.9-3.3 g/g), high tensile strength (>1.5 MPa), fast self-recovery (86 % recovery of hysteresis within 5 min) and conductivities of 0.0534-0.0593 S/m. The combination of excellent tensile properties and conductivity endowed the hydrogel-based strain sensors with good sensitivity (GF ≈ 0.8) and reliable cycling repeatability in 0-100 % strain range. Notably, the nanocomposite hydrogels can maintain their mechanical and sensing performance after soaking in water for 14 days, making them applicable for human motion detection both in air and underwater. Hence, this work provided a facile method to construct highly robust and anti-swelling CNC-reinforced conductive hydrogels, which have potential applications in underwater strain sensing and beyond.
Asunto(s)
Celulosa , Conductividad Eléctrica , Hidrogeles , Nanocompuestos , Nanopartículas , Resistencia a la Tracción , Celulosa/química , Nanocompuestos/química , Hidrogeles/química , Nanopartículas/química , Agua/química , Polímeros/química , Humanos , AcrilamidasRESUMEN
In order to enhance energy absorption, this study draws inspiration from the diagonal bilinear robust square lattice structure found in deep-sea glass sponges, proposing a design for thin-walled structures with superior folding capabilities and high strength-to-weight ratio. Firstly, the crashworthiness of bionic glass sponge tube (BGSTO) is compared with that of equal-wall-thickness equal-mass four-X tube through both experiments and simulations, and it is obtained that the specific energy absorption of BGSTO is increased by 78.64%. And the crashworthiness of BGSTO is also most significant compared to that of multicellular tubes with the similar number of crystalline cells. Additionally, we found that the double-line spacing of the glass sponge can be freely adjusted without changing the material amount. Therefore, based on BGSTO, we designed two other double-line structures, BGSTA and BGSTB. Then with equal wall thickness and mass as a prerequisite, this study proceeds to design and compare the energy absorption properties of three bilinear thin-walled tubes in both axial and lateral cases. The deformation modes and crashworthiness of the three types of tubes with variable bilinear spacing (ßO/A/B) are comparatively analysed. The improved complex proportional assessment (COPRAS) synthesis decision is used to obtain that BGSTO exhibits superior crashworthiness over the remaining two kinds of tubes. Finally, a surrogate model is established to perform multi-objective optimization on the optimal bilinear configuration BGSTO selected by the COPRAS method.