RESUMEN

PURPOSE: The present study evaluated the mechanical, surface, and optical properties of 3D-printed resins for removable prostheses reinforced by the addition of aramid fibers. MATERIALS AND METHODS: According to ISO 20795-1:2013 standards, specimens were printed using a digital light processing 3D printer and divided into two groups (n = 06/group): 3D-printed resin for denture base as the control group, and a group with the same 3D-printed resin in addition of 5% aramid fibers as the experimental group. Red aramid fibers were chosen for aesthetic characterization. The specimens were evaluated for their mechanical properties, such as elastic modulus (GPa), flexural strength (MPa), and superficial properties by their surface microhardness (KHN), surface roughness (µm), and surface free energy (mJ/m2). Optical properties were evaluated by the color difference (∆E00) between groups. The statistical test chosen after the exploratory analysis of the data was One-way ANOVA followed by Tukey's HSD (α = 0.05). RESULTS: The results showed statistical differences in elastic modulus (p < 0.0001), flexural strength (p < 0.0001), surface free energy polar variable (p = 0.0322), total surface free energy (p = 0.0344), with higher values for the experimental. Surface hardness and surface roughness showed no statistical difference (p ≥ 0.05). The color difference (∆E00) obtained through the CIEDE2000 calculus was below the perceptibility threshold (≤1.1). CONCLUSION: Adding aramid fibers to 3D-printed resin for denture bases resulted in better mechanical properties, without major alterations in surface properties. In addition, it is an easy-to-apply choice for mechanical reinforcement and aesthetic characterization, with the expression of small blood vessels in the 3D-printed resin for removable denture bases.

RESUMEN

PURPOSE: To investigate the influence of different denture-bearing conditions on the masticatory function and patient-reported outcome measures (PROMs) of complete denture wearers. METHODS: Sixty edentulous patients were selected and allocated into two groups according to the American College of Prosthodontics' (ACP) classification: non-atrophic (NAT) (Classes I and II) (n = 24) and atrophic (AT) (Classes III and IV) (n = 36). All patients received new complete dentures (CDs). The objective variables (masticatory performance and swallowing threshold) were assessed as well as the PROMs (oral health-related quality of life (OHIP-EDENT), patient satisfaction) and quality of the prosthesis, at baseline (using the old CD) and after 4 months new prostheses use. Data were analyzed by Mann-Whitney test followed by the Generalized Equations Estimation (GEE), linear regression and Chi-square test. RESULTS: Higher masticatory performance was observed in the NAT group (p < .05) for both time points, baseline and after 4 months. However, compared to baseline, both groups showed significant masticatory improvement after 4 months (p < .05). Satisfaction and overall quality of life improved after 4 months with no difference between groups (p > .05). Regarding the quality of the CD, baseline results were significantly (p < .05) lower in the AT group, but after 4 months, no significant differences were found between groups and in intragroup analysis (p > .05). CONCLUSIONS: The denture-bearing conditions seems to impact masticatory function, but the PROMs are barely affected.

Asunto(s)

RESUMEN

BACKGROUND: Edentulism remains a major disability worldwide, especially among the elderly population, although the prevalence of complete edentulism has declined over the last decades. In Uganda, the prevalence of edentulism in people aged 20 years and above is 1.8%. The therapy for edentulous patients can be realized through the use of conventional removable complete dentures, implant-supported prostheses, and computer-aided design and computer-aided manufacturing (CADCAM), however, the provision of removable complete dentures continues to be the predominant rehabilitation for edentulous patients. However, no published study has explored the lived experiences with removable complete dentures among the Ugandan population. The aim of the present study was to explore patients' lived experiences on the usage of removable complete dentures among Ugandan edentulous patients attending Makerere University Dental Hospital. METHODS: This was a qualitative study approach using purposive sampling. Fifteen (15) respondents were selected across social demographics. Interviews were recorded and transcribed and themes were generated to draw a deeper meaning to the usage of removable complete dentures. A qualitative statistical package, Atlas Ti software was used to generate themes from the interviews followed by an interpretation of the generated data and the results were presented as text and in a table. RESULTS: The reported key positive experiences due to removable complete denture rehabilitation were the improvement in speech, eating ability, regaining good facial appearance, better oral hygiene management, self-esteem and confidence to smile in public, and a feeling of completeness. However, respondents complained of pain and discomfort due to the looseness of dentures, inability to eat certain foods, and regular cleaning of dentures. The respondents did not go through proper informed consent processes before getting removable complete dentures. CONCLUSION: The study found that patients were satisfied with their removable complete dentures rehabilitation due to the positive experiences registered, such as the ability to eat and talk well, and restoration of self-esteem, all of which improved their quality of life. However, they experience pain and discomfort due to the looseness of dentures.

Asunto(s)

RESUMEN

OBJECTIVE: Evaluate the assimilation capacity and ease of handling of the Fox plane accessory by dentistry students, through a questionnaire about the experience in using this device compared to the conventional one. Its intention is to minimize possible interpretation errors and challenges that the traditional method determines. METHODS: After approval by the Research Ethics Committee, registration at Sistema Nacional de Informações sobre Ética em Pesquisa/National Information System on Research Ethics (SISNEP) and signing of the free and informed consent form, 51 undergraduate students treating patients in need of complete dentures at Instituto de Ciência e Tecnologia/Institute of Science and Technology (ICT) Unesp in São José dos Campos completed a questionnaire to evaluate the technical ease of use and provider acceptance. The obtained data were submitted to statistical analysis, evaluating technical ease and acceptance by operators. RESULTS: The results were analyzed using descriptive and inferential statistics using the Jamovi 2.2.5 software. From the responses, the frequency was obtained for each question in the questionnaire, then the weighted mean was calculated, average rating and percentage. With the results of these analyses it was possible to measure the level of satisfaction of the participants in relation to the use of the device. CONCLUSION: It was concluded that most students have difficulty using the conventional Fox plane and that the accessory facilitated the process of determining the superior orientation plane, and its ease of use.

Asunto(s)

RESUMEN

OBJECTIVE: This study aimed to explore the cross-sectional and prospective associations between self-reported functionality of complete dentures (FCD), satisfaction with complete dentures (SCD) and the ability to chew hard food (ACHF) on the one hand and the frailty index (FI) on the other hand among edentulous community-dwelling older Japanese people. METHODS: The study examined 770 edentulous participants of the Nihon University Japanese Longitudinal Study of Aging. The self-reported FCD, SCD and ability to chew six groups of food (from hardest to softest) with complete dentures were the independent variables at the baseline. The FI was computed including 40 deficits as the dependent variable at the baseline and 4 years later. Cross-sectional and prospective generalized linear regression models were fitted controlling for age, gender, marital status, education, working status and area of residence. RESULTS: The use of non-functional complete dentures and dissatisfaction with complete dentures were both associated with a higher FI cross-sectionally (3.9% [95% CI 2.2-5.6] and 3.2% [95% CI 1.5-4.9], respectively) and prospectively (3.9% [95% CI 2.0-6.0] and 3.3% [95% CI 1.3-5.3], respectively). Regarding the ability to chew, a higher FI at baseline was observed among those able to chew food of Group 2 (1.9%, [95% CI 0.1-3.7]) and Groups 4-6 (1.9%, [95% CI 0.1-3.7]), and a progressive increment in the FI, as the participants reported being able to chew softer groups of food at the follow-up (Group 2: 2.2% [95% CI 0.05-4.3]; Group 3: 3.6% [95% CI 1.2-6.0]; and Groups 4-6: 3.4 [95% CI 0.7-6.1]). CONCLUSION: Self-reported use of non-functional complete dentures, dissatisfaction with dentures and a reduced ACHF with complete dentures were associated with a higher FI both cross-sectionally and prospectively.

Asunto(s)

RESUMEN

Aim: With the significant increase in life expectancy over the last decades, it is important to understand how oral health can impact the oral health-related quality of life of older adults. This study aimed to investigate the association between need to replace dentures and oral health-related quality of life (OHRQoL) among older adults belonging to a Cohort in southern Brazil. Methods: This cross-sectional study was conducted with data from the 2019 Pelotas Elderly Cohort. The OHRQoL was assessed using the GOHAI. Need to replace dentures was self-report using a question dichotomized into yes/no. In the statistical analysis, unadjusted and adjusted models estimate from linear regression models were calculated. The significance level adopted was 5%. Results: A total of 493 older adults were included. On the GOHAI questionnaire, the mean score was 32.74 (SD±0.16). Individuals considering need of prosthesis replacement were 47.89%. Report of need to replace dentures was associated to lowest mean on the GOHAI score (ß -1.14; 95%CI - 1.80; -0.478, and on the physical (ß -0.56; 95%CI - 0.94 -0.17) and psychosocial (ß -0.48; 95%CI - 0.74; -0.22) dimensions. Conclusion: Our findings highlight the importance of also considering subjective measures of oral health in the dental care of older adults, since reporting the need for denture replacement, regardless of the reason, was associated with a worse oral health-related quality of life, including physical and psychosocial aspects

Asunto(s)

RESUMEN

Abstract Studies evaluating the roughness, wettability and microbial adhesion of 3D-printed resins for complete denture bases and teeth are scarce. Objective This study evaluated the surface roughness, wettability and adhesion of multispecies biofilms (Candida albicans, Staphylococcus aureus and Streptococcus mutans) on 3D-printed resins for complete denture bases and teeth compared to conventional resins (heat-polymerized acrylic resin; artificial pre-fabricated teeth). Methodology Circular specimens (n=39; 6.0 mm Ø × 2.0 mm) of each group were subjected to roughness (n=30), wettability (n=30) and biofilm adhesion (n=9) tests. Three roughness measurements were taken by laser confocal microscopy and a mean value was calculated. Wettability was evaluated by the contact angle of sessile drop method, considering the mean of the three evaluations per specimen. In parallel, microorganism adhesion to resin surfaces was evaluated using a multispecies biofilm model. Microbial load was evaluated by determining the number of Colony Forming Units (CFU/mL) and by scanning electron microscopy (SEM). Data were subjected to the Wald test in a generalized linear model with multiple comparisons and Bonferroni adjustment, as well as two-way ANOVA (α=5%). Results The roughness of the conventional base resin (0.01±0.04) was lower than that of the conventional tooth (0.14±0.04) (p=0.023) and 3D-printed base (0.18±0.08) (p<0.001). For wettability, conventional resin (84.20±5.57) showed a higher contact angle than the 3D-printed resin (60.58±6.18) (p<0.001). Higher microbial loads of S. mutans (p=0.023) and S. aureus (p=0.010) were observed on the surface of the conventional resin (S. mutans: 5.48±1.55; S. aureus: 7.01±0.57) compared to the 3D-printed resin (S. mutans: 4.11±1.96; S. aureus: 6.42±0.78). The adhesion of C. albicans was not affected by surface characteristics. The conventional base resin showed less roughness than the conventional dental resin and the printed base resin. Conclusion The 3D-printed resins for base and tooth showed less hydrophobicity and less adhesion of S. mutans and S. aureus than conventional resins.

RESUMEN

La prótesis parcial removible (PPR) es una alternativa de tratamiento en pacientes que perdieron algunos elementos dentarios, debido al costo relativamente bajo y a la generación de una función masticatoria satisfactoria. Además, es una buena opción cuando hay pérdida de los tejidos óseos, dado que impide la instalación de implantes dentarios. La PPR convencional presenta una estructura metálica que ofrece retención y resistencia a la prótesis, convirtiéndola en poco agradable a los pacientes, por el hecho de dejar a la vista el metal en la cavidad oral. A partir de investigadores que decidieron ir más allá del simple estudio de la función y la estética de las PPR para adentrase en sus diversas formas de presentación, surgió la prótesis parcial flexible (PFlex). La PFlex es una prótesis parcial confeccionada con resina termoplástica, sin metal y con flexibilidad. Si bien, muchos profesionales la emplean como prótesis temporal, otros tantos la han usado como alternativa a la PPR convencional. Así, uno de los frecuentes interrogantes de los clínicos es si realmente es posible utilizar la PFlex como alternativa protética definitiva. Por tanto, el propósito de este trabajo fue realizar una revisión de la literatura para evaluar si el uso de prótesis parciales removibles con resina termoplástica puede ser una alternativa a las prótesis parciales convencionales, exponiendo las ventajas, desventajas, indicaciones, contraindicaciones y las propiedades del material protético.

Removable partial denture (RPP) is an alternative treatment when it comes to patients who have lost some dental elements, as they have the advantages of a relatively low cost and a satisfactory masticatory function. Furthermore, it is a good option when there is bone tissue loss, making dental implants placement unfeasible. Conventional PPR has a metallic frame that provides retention and resistance to the prosthesis, which makes it unpalatable to patients because it leaves the metal in the oral cavity evident. Many researchers, aiming to give back beyond function and aesthetics, are studying forms of presentation of PPR, thus emerging the flexible partial prosthesis (PFlex). PFlex is a partial denture made with thermoplastic, resin metal-free and with flexibility, however its use, for many professionals, is limited only as temporary prostheses, but there are some clinicians who use PFlex as an alternative to conventional PPR. Thus, one of the questions constantly asked by scientists is whether it is possible to use PFlex as a definitive prosthetic alternative. Therefore, the aim of this study was to conduct a literature review to assess whether the use of removable partial dentures with thermoplastic resin can be an alternative to conventional partial dentures, exposing the advantages, disadvantages, indications, contraindications, and the properties of the prosthetic material.

RESUMEN

OBJECTIVE: To evaluate the anti-biofilm action of chitosan, nanoparticulate chitosan, and denture cleanser Nitradine™ against biofilms comprising Candida albicans, Candida glabrata, Staphylococcus aureus, and Streptococcus mutans. BACKGROUND: Biofilm removal from removable partial dentures (RPD) is important for success in prosthetic rehabilitation. MATERIALS AND METHODS: The anti-biofilm action of the experimental chitosan-based solutions and Nitradine™ was evaluated on acrylic resin and cobalt-chromium alloy through assessing cell viability, cell metabolism, residual aggregated biofilm, and extracellular polymeric substance and biofilm morphology. RESULTS: Only chitosan reduced the viability of C. albicans on cobalt-chromium alloy surface, by 98% (a 1.7 log10 reduction in cfu). Chitosan-based solutions neither promoted substantial alteration of the metabolic activity of the four-species biofilm nor reduced the amount of the aggregated biofilm. After immersion in chitosan and nanoparticulate chitosan, viable microorganisms and extracellular polymeric substances distributed over the entire specimens' surfaces were observed. Nitradine™ reduced the viability and metabolic activity of biofilm grown on both surfaces, but it did not remove all aggregated biofilm and extracellular polymeric substances. After immersion in Nitradine™, approximately 35% of the specimens' surfaces remained covered by aggregated biofilm, mainly composed of dead cells. CONCLUSION: Although chitosan and Nitradine™ promoted changes in the viability of microorganisms, neither solution completely removed the four-species biofilm from the Co-Cr and acrylic resin surfaces. Thus, isolated use of hygiene solutions is not indicated for biofilm control on RPDs; this requires complementary mechanical removal.

Asunto(s)

RESUMEN

OBJECTIVES: To analyse the relationship between the Frailty Index and 10 oral conditions controlling for nutritional status among Mexican community-dwelling older people. BACKGROUND: Studies suggest that the association between frailty and oral conditions are mediated by nutrition. MATERIALS AND METHODS: This cross-sectional analysis includes 487 community-dwelling men and women aged ≥70 years old. Interview and clinical examinations were performed at participants' homes. Objective (number of natural teeth, root remnants, dental condition, utilisation and functionality of removable dental prostheses and periodontitis) and subjective (utilisation of dental services, self-rated oral health, chewing difficulties and xerostomia) oral variables were collected by trained personnel. The Frailty Index was calculated considering 35 deficits. Nutritional status measured with the Mini-Nutritional assessment (MNA), age, sex, education, and marital status were included as covariates. We fitted 11 multivariate generalised linear models (one for each oral condition), assuming gamma distribution for Frailty Index as the outcome. RESULTS: Participants average age was 78.1 years, 52.1% were women. We observed a higher Frailty Index among those rating their oral health as worse than others their age (5.1%), reporting chewing difficulties often (4.9%) and fairly and very often (7.0%), and xerostomia (4.8%). Age, gender and MNA were consistently associated with the Frailty Index. CONCLUSION: Subjective oral conditions are compatible with the Frailty Index after controlling for older people's nutritional status and covariates.

Asunto(s)

RESUMEN

PURPOSE: To investigate surface characteristics (roughness and contact angle), anti-biofilm formation, and mechanical properties (mini-flexural strength) of computer-aided design and computer-aided manufacturing (CAD-CAM) polymethylmethacrylate (PMMA) polymer, and three-dimensional (3D) printed resin for denture base fabrication compared with conventional heat polymerized denture base resins. MATERIALS AND METHODS: A total of 60 discs and 40 rectangular specimens were fabricated from one CAD-CAM (AvaDent), one 3D printed (Cosmos Denture), and two conventional heat polymerized (Lucitone 199 and VipiWave) materials for denture base fabrication. Roughness was determined by Ra value; the contact angle was measured by the sessile drop method. The biofilm formation inhibition behavior was analyzed through Candida albicans adhesion, while mini-flexural strength test was done using a three-point bending test. The data were analyzed using descriptive and analytical statistics (α = 0.05). RESULTS: The CAD-CAM PMMA group showed the lowest C. albicans adhesion (log CFU/mL: 3.74 ± 0.57) and highest mini-flexural strength mean (114.96 ± 16.23 MPa). 3D printed specimens presented the highest surface roughness (Ra: 0.317 ± 0.151 µm) and lowest mini-flexural strength values (57.23 ± 9.07 MPa). However, there was no statistical difference between CAD-CAM PMMA and conventional groups for roughness, contact angle, and mini-flexural strength. CONCLUSIONS: CAD-CAM milled materials present surface and mechanical properties similar to conventional resins and show improved behavior in preventing C. albicans adhesion. Nevertheless, 3D printed resins present decreased mini-flexural strength.

Asunto(s)

RESUMEN

ABSTRACT Objective: To identify the tobacco effect on flexural properties and the microhardness of three acrylic resins. Material and Methods: Three resins were tested: two thermo-polymerizable acrylic resins (RMB 20 and BMS 014) and one autopolymerized acrylic resin. The 3-point bending and microhardness tests were carried out with a universal tensile-compression machine and a micro-Vickers hardness tester. The acrylic resin specimens have been exposed for 21 days to cigarette smoke in a smoking room. Their mechanical strength was compared to unexposed samples. Statistical analysis was performed using the data processing software SPSS Statistics 21.0. Results: The flexural properties of the resins were affected by cigarette smoke only in the case of Major Base 20® (drop in strength with p= 0.02; 0.6; 0.7 and in elastic modulus with p= 0.86; 0.74 and 0.85 for Major Base 20®, BMS 014® and Major Repair®). The cigarette smoke affected significantly microhardness for all groups (p<0.001). Conclusion: Cigarette smoking does not affect the flexural properties of the acrylic resin (BMS 014® and Major Repair® unlike Major Base 20®), but it does reduce the microhardness.

Asunto(s)

RESUMEN

OBJECTIVE: This cross-sectional study aimed to evaluate the association of oral health-related quality of life with prosthetic rehabilitation status and dental prosthesis condition in residents of Brazilian long-term care facilities. METHODS: The oral health-related quality of life of older adults (n = 194; mean [standard deviation] age = 78.93 [9.10]) was assessed by the Geriatric Oral Health Assessment Index and the Oral Health Impact Profile questionnaires. Prosthetic rehabilitation status was recorded according to the absence of teeth and use of dental prostheses. Dental prosthesis condition was considered good or poor based on stability, retention, occlusion, vertical dimension, and defects. Poisson regression models were plotted to analyze the data (α = 0.05). RESULTS: Lower Geriatric Oral Health Assessment Index scores were associated with edentulism with denture use only on one jaw (B = -0.05) and poor dental prosthesis stability (B = -0.04). Similarly, edentulous participants with denture only on one jaw (B = 0.59) and those wearing dental prostheses with poor stability (B = 0.36) are more likely to achieve higher Oral Health Impact Profile scores. Also, lower Oral Health Impact Profile scores were associated with denture defects (B = -0.34). CONCLUSION: In summary, the oral health-related quality of life of older adults living in long-term care facilities is negatively impacted by edentulism with denture only on one jaw and use of dental prostheses with poor stability. Therefore, long-term care facilities should provide oral health training to caregivers, include dental professionals in the staff, and articulate demands with oral health teams in the primary care system. (AU)

OBJETIVO: Este estudo transversal objetivou avaliar a associação da qualidade de vida relacionada à saúde bucal com o status de reabilitação protética e a condição da prótese em residentes de instituições de longa permanência no Brasil. METODOLOGIA: A qualidade de vida relacionada à saúde bucal dos idosos (n = 194; média [desvio padrão] idade = 78,93 [9,10]) foi avaliada pelos questionários Geriatric Oral Health Assessment Index e Oral Health Impact Profile. O status de reabilitação protética foi registrado de acordo com a ausência de dentes e uso de próteses dentárias. A condição da prótese foi considerada boa ou ruim com base na estabilidade, retenção, oclusão, dimensão vertical e defeitos. Modelos de regressão de Poisson foram plotados para analisar os dados (α = 0,05). RESULTADOS: Como resultado, menores escores no Geriatric Oral Health Assessment Index foram associados ao edentulismo com o uso de dentadura em apenas uma arcada (B = -0,05) e ao uso de próteses com estabilidade ruim (B = -0,04). De forma similar, participantes edêntulos que usavam dentadura em apenas uma arcada (B = 0,59) e aqueles que portavam prótese com estabilidade ruim (B = 0,36) são mais propensos a ter maiores escores no Oral Health Impact Profile. Além disso, menores escores no Oral Health Impact Profile foram associados a defeitos na prótese (B = -0,34). CONCLUSÃO: Sumarizando, a qualidade de vida relacionada à saúde bucal de idosos residentes em instituições de longa permanência é negativamente impactada pelo edentulismo com o uso de dentadura em apenas uma arcada e uso de prótese com estabilidade ruim. Assim, instituições de longa permanência devem promover capacitação em saúde bucal aos cuidadores, incluir dentistas no quadro de funcionários e articular com as equipes de saúde bucal da Atenção Primária à Saúde. (AU)

Asunto(s)

RESUMEN

Abstract Objective To assess the association between risk factors for developing denture stomatitis (DS) and oral health-related quality of life (OHRQoL) in complete denture wearers. Methodology Participants of both sexes, wearing complete dentures, were classified using the modified Newton classification for the absence or the severity of DS and allocated to groups Normal or zero, IA, IB, II, and III. Lifestyle, oral and denture history, and medication use were assessed using specific questionnaires; clinical parameters such as anatomical characteristics of support were evaluated with the Kapur classification; salivary flow (SF) was calculated by the volume of unstimulated saliva per minute; and microbial load was determined by counting colony forming units (CFU) of target microorganisms present in the biofilm collected from dentures and palate. OHIP-EDENT assessed the OHRQoL. Kendall's tau_b and Spearman tests were applied with a significance level of 5%. Results 184 patients (143 female and 41 male) aged 65.5 ± 6.8 years were evaluated. Positive correlations were found for sex (women; p=0.013, r=0.16), individuals who started to consume alcoholic beverages as a young adult (18-27 years) (p=0.008, r=0.22), CFU of Candida spp. (p<0.001, r=0.27 denture; p<0.001, r=0.31 palate); Candida albicans (p=0.004, r=0.22 denture; p=0.003, r=0.25 palate), and Candida glabrata (p=0.004, r=0.22 denture; p=0.001, r=0.27 palate). Moreover, negative correlations with DS were found for CFU of Staphylococcus spp. (p=0.004, r=-0.20 palate) and enterobacteria (p=0.002, r=-0.24 palate), as well as a negative correlation between SF (p=0.009, r=-0.193) and DS. The CFU of Staphylococcus spp. and enterobacteria on the palate significantly correlated with OHRQoL. Conclusion Being female, consuming alcoholic beverages as a young adult, CFU of Candida spp., Candida albicans, Candida glabrata, and salivary flow may be the most significant risk factors for DS. The microbial load of Staphylococcus spp. and enterobacteria seems to influence the quality of life for complete denture wearers.

RESUMEN

The aim of this study is to report a clinical case of a patient with Cushing's syndrome, low self-esteem and need for oral rehabilitation. A 50-year-old female patient with hypercortisolism sought care at School of Dentistry of the Federal University of Minas Gerais. During anamnesis, the patient reported painful symptoms and mobility of the upper and lower teeth. On clinical examination, absence of many teeth were observed, periodontal disease and caries lesions. After discussion of the case, the planning involved the extraction of all teeth, and the preparation of Maxillary Immediate Complete Dentures (ICD's) and Immediate Mandibular Implant-retained Overdenture (IMIO). The treatment proposed allowed the restored aesthetics, phonetics and chewing(AU)

O objetivo desse estudo é relatar um caso clínico de uma paciente com síndrome de Cushing, baixa autoestima e necessidade de reabilitação oral. Paciente do sexo feminino, 50 anos de idade e com hipercortisolismo, procurou atendimento na Faculdade de Odontologia da Universidade Federal de Minas Gerais. Durante a anamnese, a paciente relatou sintomas dolorosos e mobilidade dos dentes superiores e inferiores. No exame clínico, foi observada a ausência de muitos dentes, doença periodontal e lesões cariosas. Após a discussão do caso, o planejamento envolveu a extração de todos os dentes, e o preparo de Prótese Total Imediata maxilar (PTI), e Overdenture Implantorretida Imediata mandibular. O tratamento proposto permitiu que restaurasse a estética, fonética e mastigação(AU)

Asunto(s)

RESUMEN

Recursos digitais, como a manufatura subtrativa (fresagem CAD-CAM) e a manufatura aditiva (impressão 3D) podem promover significativos avanços, reduzindo o tempo e o custo de produção de próteses totais (PTs). Assim, este estudo objetiva investigar as características superficiais (rugosidade e ângulo de contato), propriedades mecânicas (resistência mini-flexural) e a adesão de biofilme sobre polímeros de PMMA pré-polimerizado para fresagem CAD-CAM e sobre resinas para impressão 3D utilizados na fabricação de bases de PTs, bem como propor um fluxo de trabalho inovador para abreviar e simplificar as etapas de confecção de PTs. Para a análise in vitro, foram fabricados um total de 60 discos e 40 barras distribuídas igualmente em quatro grupos: fresagem CAD-CAM (GF), impressão 3D (GI) e PMMA convencional termopolimerizado por ciclo longo (GCL) ou por energia de micro-ondas (GCM). A rugosidade foi determinada pelo valor de Ra; o ângulo de contato foi medido pelo método da gota séssil; o teste de resistência à mini-flexão foi obtido por teste de flexão de três pontos, enquanto o comportamento frente à formação de biofilme foi analisado através da adesão de biofilme de C. albicans. Os dados foram analisados por meio de estatística descritiva e analítica (α = 0,05). Os resultados mostraram que o GI apresentou a maior rugosidade superficial (Ra: 0,317 ± 0,151µm) e os menores valores de resistência à miniflexão (57,23 ± 9,07MPa) e o GF apresentou a menor adesão de biofilme de C. albicans (log UFC/mL: 3,74 ± 0,57) e maior média de resistência à mini-flexão (114,96 ± 16,23 MPa). Não houve diferença estatística entre o GF e os grupos convencionais para rugosidade, ângulo de contato e resistência à mini-flexão. A patente de inovação desenvolvida estabeleceu um novo fluxo de trabalho para confecção de próteses totais através de um protocolo de três consultas em que foram feitas as moldagens anatômicas na 1ª sessão, juntamente com o registro do suporte labial, plano oclusal e linhas de referência para subsidiar a montagem dos dentes superiores. Uma prótese-teste foi confeccionada por meio de procedimentos convencionais ou CAD-CAM e avaliada na 2ª consulta, permitindo observar o resultado estético, executar a moldagem funcional e realizar o registro da relação maxilo-mandibular, fornecendo referências precisas para a confecção da prótese inferior. Com base nos resultados da fase in vitro deste estudo, os corpos-de-prova obtidos a partir de disco para fresagem CAD-CAM apresentaram resistência flexural e propriedades superficiais semelhantes às resinas convencionais e mostraram um comportamento inibidor da adesão de C. albicans, enquanto os espécimes produzidos por impressão 3D exibiram a menor resistência à flexão e a maior rugosidade da superfície. O dispositivo inovador apresentado para a execução das etapas clínicas relacionadas à fabricação de PTs mostrou-se efetivo para abreviar e simplificar as técnicas disponíveis, apresentando confiabilidade e previsibilidade para produção de PTs em número de sessões reduzido (AU).

Digital features like subtractive and additive manufacturing can promote breakthroughs by reducing the time and cost of making complete dentures (CDs). Thus, this study aims to investigate surface characteristics (roughness and contact angle), mechanical properties (mini-flexural strength), and biofilm adhesion on computer-aided design/computer-aided manufacturing (CAD-CAM) PMMA polymer, and threedimensional (3D) printed resin for denture´s base fabrication as well as to propose an innovative workflow. For in vitro analysis, a total of 60 discs and 40 rectangular specimens were fabricated from one CAD-CAM pre-polymerized PMMA disc (GF), one 3D-printed (GI), and two conventional heat-polymerized (GCL and GCM) materials for denture base fabrication. Roughness was determined by the Ra value; the contact angle was measured by the sessile drop method; the mini-flexural strength test was a three-point bending test while the biofilm formation inhibition behavior was analyzed through C. albicans adhesion. The data were analyzed using descriptive and analytical statistics (α = 0.05). Results showed that GI specimens presented the highest surface roughness (Ra: 0.317 ± 0.151 µm) and lowest mini-flexural strength values (57.23 ± 9.07 MPa) and the GF showed the lowest C. albicans adhesion (log CFU/mL: 3.74 ± 0.57) and highest mini-flexural strength mean (114.96 ± 16.23 MPa). There was no statistical difference between GF and conventional groups for roughness, contact angle, and mini-flexural strength. In turn, the presented novel workflow for complete dentures fabrication reached a three appointments protocol in which preliminary impressions were made in the 1st session, all together to maxillary registration of lip support, occlusal plane, and reference lines for teeth arrangement. A trial denture was manufactured and evaluated by the 2nd appointment through conventional or CAD-CAM procedures, allowing esthetics evaluation, final impression, and maxillomandibular relationship record and providing precise references for final dentures fabrication. Based on the findings of this in vitro study, GF presented surface and mechanical properties similar to conventional resins and show improved behavior preventing C. albicans adhesion, while GI specimens exhibited the lowest flexural strength, and highest surface roughness. The proposed device for CD´s fabrication clinical procedures reached feasibility and by simplifying available techniques, this protocol could achieve reliability and predictability to produce complete dentures with reduced working time (AU).

Asunto(s)

RESUMEN

RESUMEN Fundamento: Las prótesis estomatológicas son una solución estética y funcional a la pérdida de los dientes y contribuyen a la calidad de vida de aquellos que la portan, pero el sistema estomatognático se expone a lesiones cuando no se cumplen las orientaciones para su uso, cuidado e higiene. Objetivo: Evaluar la efectividad del programa educativo para mejorar la salud bucal en pacientes portadores de prótesis estomatológicas parciales. Metodología: Se realizó un estudio preexperimento con medición antes y después de la intervención comunitaria sin grupo de control, en el período de septiembre 2019 a febrero del 2020. Se seleccionaron 50 pacientes mayores de 19 años portadores de prótesis estomatológica parcial, que cumplieron criterios de inclusión. Se utilizó la encuesta, la observación, el criterio de especialistas y el experimento como métodos del nivel empírico y estadístico-matemático para medir las variables: nivel de conocimiento, eficiencia del cepillado bucodental e higiene de las prótesis estomatológicas. Resultados: Al culminar la aplicación del programa educativo se observó un cambio de 6 % a un 52 % del nivel de conocimiento bueno sobre el uso y cuidado de las aparatologías protésica, en la eficiencia del cepillado de un 30 % a un 82 % y de un 8 % a un 68 % de buena higiene en las prótesis. Conclusiones: El programa educativo se evaluó de efectivo al obtener resultados satisfactorios en cuanto a la modificación de los conocimientos y prácticas sobre salud bucal en los pacientes portadores de prótesis estomatológicas.

ABSTRACT Background: Dentures are an esthetic and functional solution to tooth loss and contribute to life quality of those who wear them, but the stomatognathic system is exposed to lesions when guidelines for their use, care and hygiene are not followed. Objective: To assess the effectiveness of an educational program to improve oral health in patients with partial dentures. Methodology: A measurement pre-experiment study was conducted before and after community intervention without any control group, from September 2019 to February 2020. 50 patients over 19 years of age wearing partial denture who met the inclusion criteria were selected. Survey, observation, specialist criteria and experiment were used as empirical and statistical-mathematical methods to measure variables: knowledge level, oral brushing efficiency and dentures hygiene. Results: At the end of the application of the educational program, a change was observed from 6 % to 52 % in the good knowledge level on wear and care of prosthetic appliances, in brushing efficiency from 30 % to 82 % and from 8 % to 68 % in prostheses good hygiene. Conclusions: The educational program was assessed as effective in obtaining satisfactory results in terms of modification of oral health knowledge and practices in patients with dentures.

Asunto(s)

RESUMEN

Denture stomatitis (DS) is a common infection in denture wearers, especially women. This study evaluated the induction of DS using acrylic devices attached to the palate of rats combined with inoculation of Candida spp. Immunocompetent male and female rats received a carbohydrate-rich diet. Impressions were taken from the rats' palate to individually fabricate acrylic devices. Mono- and multispecies biofilms of C. albicans, C. glabrata, and C. tropicalis were grown on the devices, which were then cemented on posterior teeth and kept in the rats' palate for four weeks. Microbial samples from the palate and the device were quantified. Oral microbiome of rats inoculated with C. albicans was analyzed by 16S rRNA gene sequencing. Log10(CFU/mL) were analyzed by mixed or two-way MANOVA (α = 0.05). Candida spp. and acrylic device did not induce palatal inflammation macroscopically nor microscopically. Although there was an increase (p < 0.001) of the total microbiota and female rats demonstrated higher (p = 0.007) recovery of Candida spp. from the palate, the gender differences were not biologically relevant. The microbiome results indicate an increase in inflammatory microbiota and reduction in health-associated micro-organisms. Although Candida spp. and acrylic device did not induce DS in immunocompetent rats, the shift in microbiota may precede manifestation of inflammation.

RESUMEN

BACKGROUND: Functional bioengineered tooth regeneration using autologous or allogeneic alternative differentiated cells sources are thought to have a great potential in replacing conventional dentures. This study investigated the potential of dental pulp stem cells (DPSCs) conditioned medium for odontoblastic differentiation of Wharton's jelly mesenchymal stem cells (WJMSCs). The DPSCs derived from healthy adult permanent first molars were cultured at high confluence prior to conditioned medium collection. The WJMSCs were cultured in six different treatments, with varying ratios of culture media to DPSCs-conditioned medium. MTT assay was used to measure the rate of proliferation of WJMSCs, while immunocytochemistry staining was utilised to detect the expression of dental matrix protein 1 (DMP-1). The deposited calcium was detected and analysed via Alizarin-Red Staining (ARS). RESULTS: It was found that the proliferation of WJMSCs cultured under the mixture of complete medium and DPSCs conditioned medium showed significantly lower than the control; presumably the cells started to exit proliferative state prior differentiation. In 14 days of induction, the cells in all treatments showed osteoblastic-like morphology, calcium compound deposits were observed at day 7, 10 and 14 of differentiation suggested that DPSCs conditioned medium could lead to osteoblastic/odontoblastic differentiation. However, the DMP-1 protein can be seen only expressed minimally at day 14 of conditioned medium induction. CONCLUSIONS: In conclusion, DPSCs conditioned medium appeared as a potential odontoblastic induction approach for WJMSCs. To further investigate the stimulatory effects by DPSCs conditioned medium, specific signalling pathway need to be elucidated to enhance the differentiation efficiency.

Asunto(s)

RESUMEN

OBJECTIVES: The purposes of the present study were as follows: (1) to conduct a randomised crossover clinical trial to evaluate masticatory performance in wearers of conventional complete dentures in both arcs with conventional balanced occlusion (CBO) and lingualised balanced occlusion (LBO), using almonds as natural test food chewed for (a) 30 chewing cycles, (b) 40 chewing cycles and (c) until the subject felt ready to swallow and (2) to perform a randomised crossover clinical trial of oral health self-perception through the Geriatric Oral Health Assessment Index (GOHAI) questionnaire. BACKGROUND: During rehabilitation with full dentures, achieving stability and retention is essential for masticatory performance. A factor that can act is the appropriate occlusal scheme to be used, although the literature is full of discussions as to the most suitable occlusal scheme to be used, being CBO and LBO the most used in complete dentures. MATERIALS AND METHODS: The clinical trial was conducted with 30 participants (14 males and 16 females; average age 65.8 years). A base of interchangeable posterior teeth in the lower dentures was used, thereby changing the occlusal schemes without needing to make another complete denture. The masticatory tests and GOHAI application were conducted in two sessions: first with each occlusal scheme, and second only after participants did not report discomfort with dentures. The analysis of variance for the mixed repeated-measures test (ANOVA) was used to verify the results (α = 0.05). RESULTS: The results showed no difference in masticatory performance according to the occlusal scheme (P = .519). The masticatory performance increased with the number of cycles (P < .001) tested, regardless of the type of occlusion scheme, and oral health self-perception was higher after the second masticatory evaluation session (P = .027). CONCLUSION: The masticatory performance was similar between the two occlusal schemes, increasing according to the number of chewing cycles. The adaptive period is relevant, regardless of the occlusion scheme, because the time factor was decisive for the improvements noted in the oral health self-perception of the participants (according to the GOHAI results).

Asunto(s)