RESUMEN

PURPOSE: The major struggle in peri-implantitis therapy is the availability of successful decontamination of the infected implant surface. The main hypothesis of this study was the Er,Cr: YSGG laser decontamination efficacy investigation on the infected implant surfaces with various peri-implantitis defects. The primary objective of this study was to decide the efficacy of Er,Cr:YSGG laser as a decontamination tool at various peri-implantitis simulating defects. The secondary objective was to compare the efficacy of the Er,Cr: YSGG laser on oral biofilm removal between two protocols the first protocol (4 cycles at 2.5 min) and the second protocol (5 cycles at 5 min) at various peri-implantitis simulating defects. MATERIALS AND METHODS: A total of 3 subjects whose plaque biofilms formed in-vivo on twenty-four tested implants were divided into four tested groups. Two native implants were tested as controls.The in vitro defect model was computer-aided designed and printed into a 3D-printed model with various anulations in peri-implant infrabony defects, which were 15,30,60,and 90 degrees. RESULTS: Both Er, Cr: YSGG decontamination protocols at 50 mJ (1.5 W/30 Hz), 50% air, and 40% water were effective at reducing the total implant surface area/ biofilm ratio (%), but the second protocol had a markedly greater reduction in the duration of application (5 cycles at 5 min) than did the first protocol (4 cycles at 2.5 min). CONCLUSION: The Er, Cr: YSGG laser is an effective decontamination device in various peri-implantitis defects. The second protocol(5 cycles at 5 min) with greater application time and circles is more effective than the first one. The defect angulation influence the decontamination capability in peri-implantitis therapy. CLINICAL RELEVANCE (SCIENTIFIC RATIONALE FOR STUDY): Clinicians anticipate that the exploration of suitable therapeutic modalities for peri-implantitis therapy is limited by the obvious heterogeneity of the available evidence in the literature and need for a pre-clinical theoretical basis setup. The major challenges associated with peri-implantitis therapy include the successful decontamination of the infected implant surface, the absence of any damage to the treated implant surface with adequate surface roughness, and the biocompatibility of the implant surface, which allows osteoblastic cells to grow on the treated surface and is the key for successful re-osseointegration. Therefore, these are the expected empirical triads that need to be respected for successful peri-implantitis therapy. Failure of one of the triads represents a peri-implantitis therapeutic failure. The Er, Cr: YSGG laser is regarded as one of the expected devices for achieving the required triad. TRIAL REGISTRATION: "Efficacy of Er,Cr YSGG Laser in Treatment of Peri-implantitis". CLINICALTRIALS: gov ID NCT05137821. First Posted date: 30 -11-2021.

Asunto(s)

RESUMEN

This study aims to evaluate the repair micro-shear bond strength of the CAD/CAM resin nanoceramic block treated using four different surface treatments and composite resins of different viscosities. For the current study, 96 samples with dimensions of 14 × 12 × 2 mm were obtained from a CAD/CAM resin nanoceramic block (Cerasmart) with a low-speed precision cutting saw under water cooling. The relevant samples were randomly divided into four groups according to the surface treatment processes: grinding with diamond bur, aluminum oxide airborne-particle abrasion, long-pulse laser, and short-pulse laser. Following silane application, universal adhesive was applied to all surface-treated samples and cured with an LED for 10 s. The samples prepared for the repair procedure were divided into two subgroups (microhybrid composite and injectable composite) according to the viscosity of the repair material to be used (n = 12). After the repair procedure, care was taken to keep the samples in distilled water in an incubator at 37 °C for 24 h. The repair micro-shear bond strength values (µSBSs) of CAD/CAM resin nanoceramic-composite resin complexes were tested. In addition, randomly selected samples from each group were examined with a scanning electron microscope to evaluate the surface topography after both surface treatments and the micro-shear bond strength test. Data were analyzed by two-way ANOVA and Bonferroni test. It was determined that the surface treatment preferred in the repair protocol significantly affected the µSBS value (p < 0.001). While the highest µSBS value was obtained with the short-pulse laser airradiation group, the lowest µSBS values were found in samples with long pulse laser irradiation. However, samples grinded with a bur and airborne-particle abrasion showed similar µSBS values (p > 0.05). The preferred composite viscosity in the repair procedure has a significant effect on the µSBS value (p < 0.001). However, the interaction between the surface treatment and the viscosity of the repair composite does not affect the µSBS values in a statistically significant way (p = 0.193). It may be recommended to clinicians to repair CAD/CAM resin nanoceramic restoration surfaces with injectable composites or after treatment with short-pulse lasers.

RESUMEN

The aim of the study was to measure the degree of dentine surface roughness caused by five distinct lasers used to treat dentine hypersensitivity, as well as to evaluate the subsequent bacterial colonization on these irradiated surfaces. Sixty human maxillary premolar teeth without caries or restoration which were extracted for periodontal reasons were used in this study. Five different types of lasers were applied to the root dentin surface. Tested samples were divided into six groups of 10 samples each; control, diode (810 nm), diode (980 nm), Nd: YAG, Er: YAG, and Er, Cr: YSGG laser groups. The arithmetic mean of the surface roughness values (Ra) and the average roughness over a measurement area (Sa) were measured pre- and post-application using any of the laser types. Swab samples were then collected from the dentin surface. Following a 24-hour incubation period at 37 °C, the colony forming units were counted using a stereoscope. The results demonstrated a statistically significant difference in the surface roughness values pre- and post-application (Ra and Sa, respectively) in the Er, Cr: YSGG laser group (p = 0.037,p = 0.007). No significant difference was observed in the other groups (p > 0.05). There was no statistically significant difference in the number of bacterial colonies observed between the test and control groups. Diode and Nd: YAG lasers showed either a decrease or no change in surface roughness; however, the hard tissue lasers (Er: YAG, Er, Cr: YSGG) showed an increase. The Er: YAG and Nd: YAG laser groups exhibited decreased bacterial adhesion compared to the other groups.

Asunto(s)

RESUMEN

Introduction: The most common causes of fiber post-failure are inadequate restorations and dislodgement. This study aimed to evaluate fiber post-bond strength to dentin following Er,Cr:YSGG laser irradiation. Methods: A total of 65 human mandibular premolars with single roots were included. The 14 mm root length was instrumented with the rotary system using the crown-down technique. Gutta-percha was used for obturation, followed by conventional post space preparation. The samples were divided into two major groups: control (A) and Er,Cr:YSGG (2780 nm) laser group (B). The laser group was subdivided into (B1) 1.25 W, (B2) 1.5 W, and (B3) 1.75 W. All laser groups were set at 20 Hz, 10% and 30% water/air ratio. Fiber posts were cemented with selfadhesive cement. Each sample was divided horizontally into two slices, coronal and apical. The universal testing equipment was used to conduct a push-out test. All groups were examined by SEM and temperature changes. The statistical analysis was performed by using one-way ANOVA and Tukey HSD tests. Results: SEM images of all laser groups revealed the elimination of the smear layer and opened dentinal tubules, which was particularly noticeable in the apical region with no thermal risk to the periodontal tissue. In the push-out test, all laser groups had highly significant (P<0.001) increases in the bond strength of fiber post to dentin. The failure mode of the control group was a predominantly adhesive failure, whereas the laser groups were a predominantly mixed type. Conclusion: The three laser protocols can be used safely in the surface treatment of the fiber post space of endodontically treated teeth. Laser help to increase the bond strength of fiber post to dentin, especially in the apical area.

RESUMEN

This study evaluated the changes in surface properties of three resin-based restorative materials after two laser-assisted, in-office tooth bleaching protocols using erbium, chromium: yttrium-scandium-gallium-garnet (Er,Cr:YSGG) or diode (980 nm) lasers. A nanohybrid composite (Enamel Plus HRi), a Bis-GMA-free composite (Enamel Plus HRi Bio Function), and a resin-matrix CAD-CAM ceramic (Shofu Block HC) were tested. Forty specimens for each material were prepared and divided into four groups (n = 10/group). The control specimens did not undergo any bleaching treatment, whereas group 2 received bleaching with 40% hydrogen peroxide (H2O2), while groups 3 and 4 underwent the same bleaching procedure with the use of diode (980 nm) or Er,Cr:YSGG lasers, respectively. Surface microhardness and roughness measurements were conducted using a Vickers tester and an optical profilometer. Microhardness was lower in bleached specimens, with the nanohybrid composite exhibiting the largest difference from the no bleaching group. For the Bis-GMA-free composite the microhardness difference between no bleaching and laser-assisted bleaching were smaller than seen for the conventional bleaching technique. Surface roughness was higher in bleached specimens, with nanohybrid composite showing the largest differences from the control specimens. The examined laser-assisted tooth bleaching protocols were found not to impact surface microhardness and roughness of the tested resin-based specimens and they are deemed suitable for clinical use.

RESUMEN

AIM: To assess the degree of conversion (DC) and shear bond strength (SBS) of experimental adhesive (EA) infused with and without 1% Cerium oxide (CeO2)-NPs on metallic bracket bonded to enamel conditioned with three different pretreatment regimes PDT-activated (Riboflavin) RF, ECY (Er, Cr: YSGG), and Phosphoric acid (PA). MATERIAL AND METHOD: EA and EA modified with 1% CeO2-NPs were prepared. Characterization of CeO2NPs was assessed using a scanning electron microscope (SEM). Seventy-two premolars extracted due to periodontal or orthodontic reasons were disinfected. Samples were mounted and allocated into three groups according to enamel surface treatment before bracket bonding. Samples in Group 1 were pretreated with Traditional 37% PA-gel; Specimens in Group 2 surface treated with RF-activated PDT, and samples in Group 3 were conditioned using ECY. Brackets were placed on conditioned surfaces and samples were aged and underwent SBS testing using UTM. ARI index was used to assess bond failure. DC was evaluated for both adhesives using FTIR. ANOVA and Tukey post hoc test were used to compare the means and standard deviation (SD) of SBS and DC in different experimental groups. RESULTS: Enamel conditioned with PA and RF activated by PDT demonstrated comparable bond values with 1% CeO2 infused in EA and EA (p>0.05).ARI analysis shows that enamel conditioned with PA and RF activated by PDT showed the majority of failure types between 1 and 2 irrespective of the type of adhesive. DC value in EA (73.28±8.37) was the highest and comparable to 1% CeO2 infused in EA (66.48±6.81) CONCLUSION: RF-activated PDT can be used alternatively to 37% PA for enamel conditioning when bonding metallic brackets. Infiltration of 1% CeO2 NPs in EA improves SBS irrespective of the type of enamel conditioning. Infusion of 1% CeO2 NPs in EA demonstrates no significant difference in DC compared to EA.

RESUMEN

This study aimed to evaluate the microleakage of light-cured and self-cured adhesives on enamel surfaces selectively etched with Er, Cr: YSGG laser or 35% phosphoric acid. A total of 60 class V cavities were prepared 1 mm above the cemento-enamel junction (CEJ). The specimens were randomly divided into six groups. Group 1: Clearfil SE Bond with no conditioning, Group 2: Tokuyama Universal Bond with no conditioning, Group 3: Clearfil SE Bond conditioned with 35% phosphoric acid, Group 4: Tokuyama Universal Bond conditioned with 35% phosphoric acid, Group 5: Clearfil SE Bond conditioned with Er, Cr: YSGG laser and Group 6: Tokuyama Universal Bond conditioned with Er, Cr: YSGG laser. Microleakage was evaluated qualitatively (visually) and quantitatively (ImageJ). The data were analyzed using IBM SPSS V23 and submitted to Kruskal-Wallis and Wilcoxon tests. The significance level was set at p < 0.05. In all evaluation methods, the microleakage scores exhibit significant differences (p*<0.001). Group 1 and Group 3 exhibited similar and lower microleakage values than the Group 5. In the occlusal margin, the microleakage values were similar in Group 2, Group 4, and Group 6, whereas in the gingival margin Group 4 showed significantly lower leakage compared to Group 2. Regardless of the etching protocols and adhesive systems used, less microleakage was observed on the occlusal surface than on the gingival surface. Phosphoric acid etching provides better results than laser etching for enamel surface treatment on both occlusal and gingival surfaces.

Asunto(s)

RESUMEN

The aim of this study was to verify the effectiveness of attenuated total reflectance-fourier transform infrared (ATR-FTIR) spectroscopy in the characterization of bone repair in mandibular osteotomy using erbium, chromium-doped yttrium, scandium, gallium and garnet (Er,Cr:YSGG) laser and multilaminate drill on each side. Two mandible bone fragments were removed from 30 rabbits, and the process of bone repair was studied immediately, 3, 7, 15, 21, and 28 days after the surgery. The histological analysis allowed detecting differences in the early stages of tissue repair after bone cutting performed with the Er,Cr:YSGG laser or multilaminate drill. The ATR-FTIR spectroscopy technique was sensitive to changes in the organic content of bone tissue repair process.

Asunto(s)

RESUMEN

Background and Objective: Eliminating intracanal Enterococcus faecalis (E. faecalis) is challenging because of its ability to penetrate deep dentinal tubules and its high resistance to many chemicals. This study evaluated the effectiveness of conventional needle irrigation and three different irrigant activation methods in reducing E. faecalis. Methods: The root canals of extracted teeth were shaped, contaminated with E. faecalis, and incubated for three weeks. They were randomly allocated to four experimental groups of 15 teeth each according to the final irrigation method: group 1, conventional needle irrigation; group 2, passive ultrasonic (PU) irrigation; group 3, XP-endo Finisher (XPF); and group 4, laser-activated (LA) irrigation. Bacterial samples were taken and cultured before and after these final irrigation procedures. The colony-forming units were counted, and the bacterial reduction percentages of each group were calculated. The Kruskal-Wallis and Dunnet tests were used for statistical analysis. Results: All irrigant activation methods were significantly more effective than conventional needle irrigation. Although the LA group generated more negative samples than PU, there was no statistically significant difference between the LA and PU groups. LA was significantly more effective than the XPF, whereas PU and XPF were statistically similar. Conclusions: Within the limitations of this study, the final irrigation with LA and PU showed the best reductive effect on E. faecalis colonies. Considering that the LA group had more negative samples, it may be chosen as an alternative to enhance root canal disinfection, especially in difficult cases.

RESUMEN

BACKGROUND: Erbium lasers safely offer the possibility of reuse for debonded restorations. Since these lasers have a high affinity for water molecules, they are absorbed by resin cement causing explosive ablation of the cement and thus, the restoration debonds. The efficiency of this process depends on many factors, including the ceramic type, its chemical composition and thickness. Therefore, this study was designed to test the time taken to debond ultrathin occlusal veneers made of three types of milled ceramic materials and evaluate the integrity of these restorations after debonding. METHODS: Three ceramic types were evaluated in this study: lithium disilicate (IPS Emax CAD), highly condensed lithium disilicate (GC initial®LiSi), and translucent zirconia (Katana zirconia STML). Each group consisted of 8 occlusal veneers of 0.5 mm thickness. The samples were cemented to the occlusal surfaces of the upper molar teeth. An Er; Cr: YSGG laser was applied to the occlusal veneers using the scanning method, and time until debonding was calculated. The debonded samples were then inspected under a stereomicroscope for possible damage. Numerical data are presented as the mean with 95% confidence interval (CI), standard deviation (SD), minimum (min.) and maximum (max.) values. Normality and variance homogeneity assumptions were confirmed using Shapiro-Wilk's and Levene's tests, respectively. Data were normally distributed and were analyzed using one-way ANOVA followed by Tukey's post hoc test. The significance level was set at p < 0.05 for all tests. Statistical analysis was performed with R statistical analysis software version 4.3.2 for Windows (R Core Team (2023). R: A language and environment for statistical computing. R Foundation for Statistical Computing, Vienna, Austria. URL https://www.R-project.org/). RESULTS: There was no significant difference in debonding time between the different materials (p = 0.995). The longest debonding time was found for Katana STML (87.52 ± 20.45) (seconds), followed by Emax (86.94 ± 20.63) (seconds), while the lowest value was found for LiSi initial (86.14 ± 25.16) (seconds). In terms of damage to the debonded veneers, The Emax and zirconia samples showed no damage. However, 40% of the LiSi samples fractured during debonding, and 20% exhibited cracks. Only 40% of the LiSi samples were sound after debonding. CONCLUSION: Er; Cr: YSGG laser can be used efficiently to remove ceramic occlusal veneers. However, its effect on LiSi restorations needs further research.

Asunto(s)

RESUMEN

The aim of this study is to investigate the repair bond strength of composite resin following three different surface treatments (bur-grinding, silanization, and Er,Cr:YSGG laser irradiation) using various universal adhesives. A total of 160 resin composite specimens, produced in cylindrical form (6 × 2 mm) with a nanohybrid composite resin within metal molds, were subjected to 5000 cycles of aging in a thermocycler. The aged samples were categorized into four groups based on surface treatments: control, bur, silane, and Er,Cr:YSGG laser. Following surface treatments, the specimens underwent repair using the same resin composite and four different adhesive systems: Tokuyama Universal Bond (TUB), Prime Bond Universal (PBU), Gluma Bond Universal (GBU), and Clearfil SE Bond (CSB). Subsequently, the specimens were subjected to shear forces, and statistical analysis was performed using two-way ANOVA and Tukey tests (p < 0.05). The failure modes were examined using a stereomicroscope, and the surface topography of the roughened resin composite was assessed through scanning electron microscopy (SEM). Results indicated that silane + GBU exhibited the highest shear bond strength (SBS) (15.61 MPa) while control + TUB showed the lowest SBS (7.63 MPa). Silane demonstrated significantly higher SBS values (p ≤ 0.05), with no significant difference observed between bur and laser methods (p = 0.998). It is recommended to include an additional silanization step before applying universal adhesive, as it effectively enhances the bond strength of the repaired composite.

Asunto(s)

RESUMEN

The aim of this in vitro study was to evaluate the effect of the pre-application of a dentin-bonding agent and the application of different lasers on the prevention of tooth discoloration caused by mineral trioxide aggregate (MTA) in the presence of blood. Sixty extracted human anterior teeth were selected, with root lengths standardized to 10 mm and root canals shaped using Gates-Glidden drills #3 to #5. The samples were divided into six groups (n = 10): Group 1 with no surface treatment and Groups 2 to 6 with Optibond universal adhesive and Neodymium yttrium aluminum garnet (Nd:YAG), Erbium yttrium aluminum garnet (Er:YAG), Erbium-chromium-yttrium-scandium-gallium-garnet (Er:Cr:YSGG), and diode laser applications, respectively. Root canals were filled with fresh human blood, and ProRoot MTA and a collagen barrier were then placed. Color changes were measured with a spectrophotometer at 0, 7, 30, 90, and 180 days post MTA placement. Color differences (∆E) were analyzed using a two-factor mixed-design ANOVA with the Sidak method (p = 0.05). All treatment groups exhibited discoloration above the acceptability threshold. Although all treatment approaches exhibited less color change compared to the control group (p < 0.05), there was no significant difference among them in terms of preventing color change (p > 0.05). It was determined that none of the methods could guarantee 100% prevention of discoloration caused by MTA-blood contact.

RESUMEN

Background and Objectives: This paper aims to assess the role of laser therapy in periodontitis through an innovative approach involving computational prediction and advanced modeling performed through network analysis (Gaussian graphical models-GGMs) and structural equations (SEM). Materials and Methods: Forty patients, exhibiting periodontal pockets with a minimum depth of 5 mm, were randomly divided into two groups: a control group and a laser group. Four specific indicators were measured for each tooth, namely periodontal pocket depth (PPD), clinical attachment level (CAL), bleeding on probing (BOP), and plaque index (PI), and the mean of six measured values was recorded at five time markers (baseline, 6 months, 1 year, 2 years, and 4 years). The assessment algorithm included enrollment, measurements, and differential non-surgical periodontal treatment, according to the group allocation. Scaling, root planing, and chlorhexidine 1% were conducted for the control group, and scaling, root planing and erbium, chromium:yttrium-scandium-gallium-garnet (Er,CR:YSGG) laser therapy were conducted for the laser group. Results: The main results highlight that the addition of laser treatment to scaling and root planing led to notable clinical improvements, decreasing the PPD values, reducing the BOP scores, and increasing the CAL. Conclusions: Notable relationships between the specific indicators considered were highlighted by both the GGMs and by SEM, thus confirming their suitability as proxies for the success of periodontal treatment.

Asunto(s)

RESUMEN

In the last two decades, the activation of root canal irrigants with pulsed lasers as an adjunct in root canal treatment has become increasingly popular. This narrative review explains the physical basics and the working mechanism of laser-activated irrigation (LAI), explores the parameters influencing LAI efficacy, considers historical evolutions in the field and summarizes laboratory and clinical evidence with emphasis on the antimicrobial action of LAI. Cavitation is the driving force behind LAI, with growing and imploding vapour bubbles around the laser tip causing various secondary phenomena in the irrigant, leading to intense liquid dynamics throughout the underlying root canal. High-speed imaging research has shown that laser wavelength, pulse energy, pulse length and fibre tip geometry are parameters that influence this cavitation process. Nevertheless, this has not resulted in standardized settings for LAI. Consequently, there is significant variability in studies assessing LAI efficacy, complicating the synthesis of results. Laboratory studies in extracted teeth suggest that, with regard to canal disinfection, LAI is superior to conventional irrigation and there is a trend of higher antimicrobial efficacy of LAI compared to ultrasonic activation. Clinical evidence is limited to trials demonstrating similar postoperative pain levels after LAI versus no activation or ultrasonic activation. Clinical evidence concerning the effect of LAI on healing of apical periodontitis as yet is scarce.

Asunto(s)

RESUMEN

The internal topography of the root canal is complex, especially for the permanent molar's mesial root. In response to such issues, improved irrigation techniques have been created, which use laser pulses to agitate fluids and improve microbial deposit removal. Objective: To assess the effectiveness of the Er,Cr:YSGG laser with a wavelength of 2,780 nm via photon-induced photoacoustic streaming (PIPS) protocol which agitated of 2% chlorohexidine (CHX) in removing mature Enterococcus faecalis (E. faecalis) biofilm in root canal systems of lower molars. Material and Methods: The mesial roots of lower first and second molars were separated and inoculated with E. faecalis bacterial suspension for 30 days. The roots were irrigated with CHX, some of them were agitated with a passive ultrasonic device (PUI), while the other roots were agitated by an Er,Cr:YSGG laser in PIPS at 60 µs/pulse, 5 Hz, (0.25, 0.5, 0.75, and 1) W. An atomic force microscope (AFM) was used as a new method to get the results in the isthmus area; the obtained results from each group were compared with each other. Results: Based on the AFM and SEM analyses, laser and ultrasonic activation groups showed higher antimicrobial efficacy than the conventional syringe irrigation group (P<0.05). Conclusion: Based on the investigation's findings, the activation of 2% CHX solution by Er,Cr:YSGG laser in PIPS and PUI offers better mature bacterial biofilm removal in the mesial root of lower human molars than the same irrigant with the SI technique (AU)

A topografia interna do canal radicular é complexa, especialmente para a raiz mesial do molar permanente. Em resposta a esses problemas, foram criadas técnicas aprimoradas de irrigação, que utilizam pulsos de laser para agitar fluidos e melhorar a remoção de depósitos microbianos. Objetivo: Avaliar a eficácia do laser Er,Cr:YSGG com comprimento de onda de 2.780 nm via protocolo de streaming fotoacústico induzido por fótons (PIPS) que agitou clorohexidina a 2% (CHX) na remoção de Enterococcus faecalis maduro (E. faecalis) biofilme em sistemas de canais radiculares de molares inferiores. Material e Métodos: As raízes mesiais de 28 primeiros e segundos molares inferiores foram separadas e inoculadas com suspensão bacteriana de E. faecalis por 30 dias. As raízes foram irrigadas com CHX, sendo algumas delas agitadas com aparelho ultrassônico passivo (PUI), enquanto as demais raízes foram agitadas com laser Er,Cr:YSGG em PIPS a 60 µs/pulso, 5 Hz (0,25, 0,5, 0,75 e 1) W. Um microscópio de força atômica (AFM) foi utilizado como um novo método para obter os resultados na área do istmo; os resultados obtidos de cada grupo foram comparados entre si. Resultados: Com base nas análises de AFM e SEM, os grupos de ativação por laser e ultrassom apresentaram maior eficácia antimicrobiana do que o grupo de irrigação com seringa convencional (P<0.05). Conclusão: Com base nos achados da investigação, a ativação da solução de CHX a 2% pelo laser Er,Cr:YSGG em PIPS a (60 µs/pulso, 5 Hz, 0,75 W) oferece melhor remoção de biofilme (AU)

Asunto(s)

RESUMEN

Abstract Oral soft tissue lesions require a precise diagnosis by oral biopsy with the ability to recognize these lesions within histopathological levels, so the instrument used for the incisions should be safe and cause little to no harm to the surrounding tissue. Objective This study compared a dual-wavelength diode laser and an Er, Cr:YSGG laser in oral soft tissue incisions to determine the most effective and safest laser system at the histopathological level. Methodology The (810 and 980 nm) dual-wavelength diode laser was used at 1.5 W and 2.5 W (CW) power settings, and the (2780 nm) Er, Cr:YSGG laser was used at 2.5 W and 3.5 W (PW) power settings. Both laser systems were used to incise the tissues of freshly dissected sheep tongue pieces to obtain the following histopathological criteria: epithelial tissue changes, connective tissue changes, and lateral thermal damage extent by optical microscopy. Results The epithelial and connective tissue damage scores were significantly higher in the dual-wavelength diode laser groups than in the Er, Cr:YSGG laser groups (P<0.001), and there was a significant difference between some groups. The extent of lateral thermal damage was also significantly higher in the diode laser groups than in the Er, Cr: YSGG laser groups (P<0.001), and there was a significant difference between groups. Group 2 (2.5 W) of the diode laser was the highest for all three criteria, while group 3 (2.5 W) of the Er, Cr:YSGG laser was the lowest. Conclusion The Er, Cr:YSGG laser with an output power of 2.5 W is, histologically, the most effective and safest laser for oral soft tissue incision. The dual-wavelength diode laser causes more damage than the Er, Cr:YSGG laser, but it can be used with a low output power and 1 mm safety distance in excisional biopsy.

RESUMEN

Introduction: The purpose of this in vitro study is to ascertain how NovaMin and Er,Cr:YSGG laser radiation affect the remineralization of primary tooth enamel lesions. Methods: 40 main teeth served as the study's sample size. These teeth were allocated into five groups at random. The first group served as a negative control (artificial saliva); the second group served as a positive control (APF gel 1.23%); the third group NovaMin, the fourth group Er,Cr:YSGG laser, the fifth group Er,Cr:YSGG laser and finally, the application of NovaMin. For the purpose of measuring microhardness, all samples were submitted to the dental materials laboratory three times. Results: The collected data were compared using the SPSS 28 program between the baseline measurement, after demineralization, and after remineralization. The data were analyzed using ANCOVA and Bonferroni tests. All groups demonstrated a considerable increase in microhardness as compared to the negative control group (P<0.05). With the exception of the third and fourth groups, there was no discernible difference in the rise in microhardness between the other groups. The third and fourth groups were compared, and the results revealed that NovaMin had a greater impact than laser therapy alone (P=0.023). Scanning electron microscopy (SEM) analysis backed up the findings. Conclusion: In comparison to using the Er,Cr:YSGG laser alone, using NovaMin alone can speed up the remineralization of erosion lesions on the surface of primary teeth.

RESUMEN

Purpose: The aim of this study is to compare the bond strength of lingual brackets bonded to resin-matrix and lithium disilicate based-ceramic crowns following various surface treatments. Materials and methods: Sixty ceramic crowns (IPS Emax and Cerasmart) were fabricated by CAD/CAM. Er,Cr:YSGG laser, sandblasting with aluminium oxide and hydrofluoric acid treatment effects on ceramics was tested (n=10/group). A light-cure orthodontic adhesive was used to bond lingual brackets to the ceramic surfaces. Bond strengths of the brackets to ceramics were assessed by shear bond test. The remnant adhesive on bracket and ceramic surfaces was inspected with a light microscope and adhesive remnant index scores were recorded. The data were analyzed statistically using the Kruskal-Wallis test followed by the Mann-Whitney U-test. Results: Cerasmart ceramic specimens showed lower shear bond strength values than IPS Emax ceramic specimens (p<0.05). The statistical analysis of the surface treatment groups regarding bond strength were ranked as follows: Laser ≤ Hydrofluoric acid ≤ Sandblasting (p=0.058). While laser-treated Cerasmart ceramic group displayed the lowest SBS (9.39 MPa), hydrofluoric acid-treated IPS Emax group had the highest (16.8 MPa) bond strength value. Conclusion: The use of Er,Cr:YSGG lasers for etching of CAD-CAM ceramics could be a promising alternative to "conventional techniques", to improve bond strength of lingual brackets to IPS Emax and Cerasmart ceramics.

RESUMEN

Introduction: Lasers are one of the most advantageous tools that have been used in a variety of medical fields. Soft tissue management is an important part of oral and maxillofacial surgery. There are different surgical procedures for management; one of them is laser surgery. The purpose of this study was to compare the dual-wavelength diode laser and the Er, Cr: YSGG laser to choose the most effective laser for a soft tissue incision in oral and maxillofacial surgery regarding temperature elevation. Methods: A dual-wavelength diode laser (810 and 980 nm) with 1.5 W and 2.5 W power outputs and an Er, Cr: YSGG (2780 nm) with 2.5 W and 3.5 W power outputs were used to make 50 incisions in six freshly dissected sheep tongues. The temperature means were measured at initial, maximum temperatures, as well as the temperature rise (difference between initial and maximum), and all were compared between the groups of soft tissue. Results: The lowest mean temperature rise was observed with a 2.5 W Er, Cr: YSGG laser, and the highest mean temperature rise was observed with a 2.5 W diode laser, and all samples from the two lasers showed a statistically significant difference (P<0.05) in the temperature rise except the 1.5 W diode, which is higher but not statistically significantly different from the 3.5 W Er, Cr: YSGG laser (P=0.100). Conclusion: The power output of 2.5 W of an Er, Cr: YSGG laser produced low levels of temperature rise compared to a diode laser and produced surgical incisions with a lower probability of heat damage to surrounding tissues.

RESUMEN

Objective: This 1-year prospective clinical trial was designed to assess the microbial, clinical, radiographic, and prosthetic parameters after disinfection of the implant abutment connection using Er,Cr:YSGG (erbium, chromium-doped: yttrium, scandium, gallium, and garnet) and Nd:YAG (neodymium-doped yttrium, aluminum, garnet). Materials and methods: All the patients were divided into four groups; Group I: Nd:YAG laser, Group II: Er,Cr:YSGG laser, Group III: 0.2% chlorhexidine (CHx), and Group IV: steam disinfection. Peri-implant parameters assessed included peri-implant bleeding scores (PIBS), peri-implant plaque scores (PIPS), peri-implant pocket depth (PIPD), and crestal bone loss (CBL). The peri-implant plaque samples were acquired to perform microbiological analysis to assess Porphyromonas gingivalis, Treponema denticola, and Tannerella forsythia, respectively. All measurements were completed at baseline, 6 months, and 12 months postsurgery. Multiple groups were compared with the help of the Bonferroni post-hoc adjustment test (p < 0.01). Logistic regression models were utilized to assess the association between age, oral hygiene practices (brushing and flossing), and duration of implant function. Results: At the baseline level, there were no discernible differences in the peri-implant parameters between the study groups (p > 0.05). At the 6-month (p < 0.01) and 12-month (p < 0.001) follow-ups, all four study groups demonstrated a significant improvement in PIPS and PIBS, with no significant differences between the groups at baseline (p > 0.05). Based on an intergroup comparison, Group I (Nd:YAG) showed a significant decrease in PIBS when compared with the other groups. Group II showed a considerable decrease in PIPD and enhancements in CBL when compared with Groups I, III, and IV (p < 0.01). At the 6- and 12-month follow-up periods, P. gingivalis and T. denticola reduction were found to be statistically higher in Group II, whereas P. gingivalis and T. forsythia mean log CFU/mL were found to be statistically higher in Group I. Conclusions: Nd:YAG and Er,Cr:YSGG lasers both outperformed CHx and steam disinfection in terms of clinical, peri-implant, and prosthetic results when used to clean implant abutments.

Asunto(s)