RESUMEN

Standard structural health monitoring techniques face well-known difficulties for comprehensive defect diagnosis in real-world structures that have structural, material, or geometric complexity. This motivates the exploration of machine-learning-based structural health monitoring methods in complex structures. However, creating sufficient training data sets with various defects is an ongoing challenge for data-driven machine (deep) learning algorithms. The ability to transfer the knowledge of a trained neural network from one component to another or to other sections of the same component would drastically reduce the required training data set. Also, it would facilitate computationally inexpensive machine learning based inspection systems. In this work, a machine-learning-based multi-level damage characterization is demonstrated with the ability to transfer trained knowledge within the sparse sensor network. A novel network spatial assistance and an adaptive convolution technique are proposed for efficient knowledge transfer within the deep learning algorithm. Proposed structural health monitoring method is experimentally evaluated on an aluminum plate with artificially induced defects. It was observed that the method improves the performance of knowledge transferred damage characterization by 50 % during localization and 24 % during severity assessment. Further, experiments using time windows with and without multiple edge reflections are studied. Results reveal that multiply scattered waves contain rich and deterministic defect signatures that can be mined using deep learning neural networks, improving the accuracy of both identification and quantification. In the case of a fixed sensor network, using multiply scattered waves shows 100 % prediction accuracy at all levels of damage characterization.

RESUMEN

Underwater acoustic sensor networks (UASNs) are critical to a range of applications from oceanographic data collection to submarine surveillance. In these networks, efficient energy management is critical due to the limited power resources of underwater sensors. The LEACH protocol, a popular cluster-based protocol, has been widely used in UASNs to minimize energy consumption. Despite its widespread use, the conventional LEACH protocol faces challenges such as an unoptimized cluster number and low transmission efficiency, which hinder its performance. This paper proposes an improved LEACH protocol for cluster-based UASNs, where the cluster number is optimized with an underwater energy propagation model to reduce energy consumption, and a transmission scheduling algorithm is also employed to achieve conflict-free parallel data transmission. Replication computing is introduced to the LEACH protocol to reduce the signaling in the clustering and data transmission phases. The simulation results show that the proposed protocol outperforms several conventional methods in terms of normalized average residual energy, average number of surviving nodes, average round when the first death node occurs, and the number of packets received by the base station.

RESUMEN

Acoustic energy mapping provides the functionality to obtain characteristics of acoustic sources, as: presence, localization, type and trajectory of sound sources. Several beamforming-based techniques can be used for this purpose. However, they rely on the difference of arrival times of the signal at each capture node (or microphone), so it is of major importance to have synchronized multi-channel recordings. A Wireless Acoustic Sensor Network (WASN) can be very practical to install when used for mapping the acoustic energy of a given acoustic environment. However, they are known for having low synchronization between the recordings from each node. The objective of this paper is to characterize the impact of current popular synchronization methodologies as part of the WASN to capture reliable data to be used for acoustic energy mapping. The two evaluated synchronization protocols are: Network Time Protocol (NTP) y Precision Time Protocol (PTP). Additionally, three different audio capture methodologies were proposed for the WASN to capture the acoustic signal: two of them, recording the data locally and one sending the data through a local wireless network. As a real-life evaluation scenario, a WASN was built using nodes conformed by a Raspberry Pi 4B+ with a single MEMS microphone. Experimental results demonstrate that the most reliable methodology is using the PTP synchronization protocol and audio recording locally.

RESUMEN

Wireless acoustic sensor networks (WASNs) and intelligent microsystems are crucial components of the Internet of Things (IoT) ecosystem. In various IoT applications, small, lightweight, and low-power microsystems are essential to enable autonomous edge computing and networked cooperative work. This study presents an innovative intelligent microsystem with wireless networking capabilities, sound sensing, and sound event recognition. The microsystem is designed with optimized sensing, energy supply, processing, and transceiver modules to achieve small size and low power consumption. Additionally, a low-computational sound event recognition algorithm based on a Convolutional Neural Network has been designed and integrated into the microsystem. Multiple microsystems are connected using low-power Bluetooth Mesh wireless networking technology to form a meshed WASN, which is easily accessible, flexible to expand, and straightforward to manage with smartphones. The microsystem is 7.36 cm3 in size and weighs 8 g without housing. The microsystem can accurately recognize sound events in both trained and untrained data tests, achieving an average accuracy of over 92.50% for alarm sounds above 70 dB and water flow sounds above 55 dB. The microsystems can communicate wirelessly with a direct range of 5 m. It can be applied in the field of home IoT and border security.

RESUMEN

This work presents the design of a wireless acoustic sensor network (WASN) that monitors indoor spaces. The proposed network would enable the acquisition of valuable information on the behavior of the inhabitants of the space. This WASN has been conceived to work in any type of indoor environment, including houses, hospitals, universities or even libraries, where the tracking of people can give relevant insight, with a focus on ambient assisted living environments. The proposed WASN has several priorities and differences compared to the literature: (i) presenting a low-cost flexible sensor able to monitor wide indoor areas; (ii) balance between acoustic quality and microphone cost; and (iii) good communication between nodes to increase the connectivity coverage. A potential application of the proposed network could be the generation of a sound map of a certain location (house, university, offices, etc.) or, in the future, the acoustic detection of events, giving information about the behavior of the inhabitants of the place under study. Each node of the network comprises an omnidirectional microphone and a computation unit, which processes acoustic information locally following the edge-computing paradigm to avoid sending raw data to a cloud server, mainly for privacy and connectivity purposes. Moreover, this work explores the placement of acoustic sensors in a real scenario, following acoustic coverage criteria. The proposed network aims to encourage the use of real-time non-invasive devices to obtain behavioral and environmental information, in order to take decisions in real-time with the minimum intrusiveness in the location under study.

Asunto(s)

RESUMEN

In long distance sensor nodes, propagation delay is the most crucial factor for the successful transmission of data packets in underwater acoustic sensors networks (UWAs). Therefore, to cope with the problem of propagation delay, we propose examining and selecting the best relay node (EBRN) technique based on checking the eligibility and compatibility of RN and selecting the best RN for UWAs. In the EBRN technique, the source node (S) creates a list of the best RNs, based on the minimum propagation delay to the midpoint of a direct link between S and the destination node (D). After that, the S attaches the list of selected RNs and transmit to the D along with data packets. Finally, from the list of selected RNs, the process of retransmission is performed. To avoid collision among control packets, we use a backoff timer that is calculated from the received signal strength indicator (RSSI), propagation delay and transmission time, whereas the collision among data packets is avoided by involving single RN in a particular time. The performance of the proposed EBRN technique is analyzed and evaluated based on throughput, packet loss rate (LR), packet delivery ratio (PDR), energy efficiency, and latency. The simulation results validate the effectiveness of the proposed EBRN technique. Compared with the existing schemes such as underwater cooperative medium access control (UCMAC) and shortest path first (SPF), the proposed EBRN technique performs remarkably well by increasing the throughput, PDR, and energy efficiency while decreasing the latency and LR in UWAs.

Asunto(s)

RESUMEN

Underwater acoustic sensor networks (UWASNs) can revolutionize the subsea domain by enabling low-cost monitoring of subsea assets and the marine environment. Accurate localization of the UWASNs is essential for these applications. In general, range-based localization techniques are preferred for their high accuracy in estimated locations. However, they can be severely affected by variable sound speed, multipath spreading, and other effects of the acoustic channel. In addition, an inefficient localization scheme can consume a significant amount of energy, reducing the effective life of the battery-powered sensor nodes. In this paper, we propose robust, efficient, and practically implementable localization schemes for static UWASNs. The proposed schemes are based on the Time-Difference-of-Arrival (TDoA) measurements and the nodes are localized passively, i.e., by just listening to beacon signals from multiple anchors, thus saving both the channel bandwidth and energy. The robustness in location estimates is achieved by considering an appropriate statistical noise model based on a plausible acoustic channel model and certain practical assumptions. To overcome the practical challenges of deploying and maintaining multiple permanent anchors for TDoA measurements, we propose practical schemes of using a single or multiple surface vehicles as virtual anchors. The robustness of localization is evaluated by simulations under realistic settings. By combining a mobile anchor(s) scheme with a robust estimator, this paper presents a complete package of efficient, robust, and practically usable localization schemes for low-cost UWASNs.

RESUMEN

Initialization methods for underwater wireless acoustic sensor networks (UWASNs) have been proposed as a subset of other network protocols under the simple assumption that all the nodes in the network can be initialized at once. However, it is generally time- and energy-intensive to initialize all nodes in a UWASN due to unstable underwater channel conditions. To improve network efficiency, we propose the Application-based Partial Initialization (API) protocol, which initializes only the same number of nodes as the number of activated nodes required to run a specific application. Reducing the number of active nodes is also particularly advantageous underwater since the replacement of batteries is costly. To the best of our knowledge, the API is the first approach that initializes nodes partially according to applications. Thus, we investigate the feasibility of the API for a UWASN by analyzing its performance via simulations. From the results, it is shown that the API provides similar data statistics compared with the conventional full initialization that initializes all nodes. Moreover, the API outperforms the full initialization in terms of the initialization time and message overhead performances.

RESUMEN

This paper presents a novel autonomous environmental monitoring methodology based on collaboration and collective decision-making among robotic agents in a heterogeneous swarm developed within the project subCULTron, tested in a realistic marine environment. The swarm serves as an underwater mobile sensor network for exploration and monitoring of large areas. Different robotic units enable outlier and fault detection, verification of measurements and recognition of environmental anomalies, and relocation of the swarm throughout the environment. The motion capabilities of the robots and the reconfigurability of the swarm are exploited to collect data and verify suspected anomalies, or detect potential sensor faults among the swarm agents. The proposed methodology was tested in an experimental setup in the field in two marine testbeds: the Lagoon of Venice, Italy, and Biograd an Moru, Croatia. Achieved experimental results described in this paper validate and show the potential of the proposed approach.

RESUMEN

Underwater wireless sensor networks (UWSNs) is emerging as an advance terminology for monitoring and controlling the underwater aquatic life. This technology determines the undiscovered resources present in the water through computational intelligence (CI) techniques. CI here pertains to the capability of a system to acquire a specific task from data or experimental surveillance below the water. In today's time data is considered as the identity for everything that exists in nature, whether that data is related to human beings, machines or any type of device like internet of underwater things (IoUT). The collected data should be correct, complete and fulfill the requirements of a particular task to be done. Underwater data collection is very tough because of sensors mobility due to water drift 3 meters/sec, crest and trough. A lot of packet drop also exists due to underwater conditions that hurdles the data collection process. Various techniques already exists for efficient collection of data below the water but these are not properly classified. This manuscript has summarized the concept of data collection in UWSN along with its classification based on routing. Also, a short discussion about existence of CORONA below the water along with water purification is carried out. Furthermore, some data routing approaches are also analyzed on the basis of quality of service parameters and the current challenges to be tackled during data collection are also discussed.

RESUMEN

Underwater acoustic sensor networks have recently attracted considerable attention as demands on the Internet of Underwater Things (IoUT) increase. In terms of efficiency, it is important to achieve the maximum communication coverage using a limited number of sensor nodes while maintaining communication connectivity. In 2017, Kim and Choi proposed a new deployment algorithm using the communication performance surface, which is a geospatial information map representing the underwater acoustic communication performance of a targeted underwater area. In that work, each sensor node was a vertically separated hydrophone array, which measures acoustic pressure (a scalar quantity). Although an array receiver is an effective system to eliminate inter-symbol interference caused by multipath channel impulse responses in underwater communication environments, a large-scale receiver system degrades the spatial efficiency. In this paper, single-vector sensors measuring the particle velocity are used as underwater sensor nodes. A single-vector sensor can be considered to be a single-input multiple-output communication system because it measures the three directional components of particle velocity. Our simulation results show that the optimal deployment obtained using single-vector sensor nodes is more effective than that obtained using a hydrophone (three-channel vertical-pressure sensor) array.

RESUMEN

The improvement of quality of life in the framework of the smart city paradigm cannot be limited to a set of objective measures carried out over several critical parameters (e.g., noise or air pollution). Noise disturbances depend not only on the equivalent level LAeq measured, but also on the spectral distribution of the sounds perceived by people. Propagation modelling to conduct auralization can be done either with geometrical acoustics or with wave-based methods, given the fact that urban environments are acoustically complex scenarios. In this work, we present a first analysis of the acoustic spectral distribution of street noise, based on the frequency selectivity of the urban outdoor channel and its corresponding coherence bandwidth. The analysis was conducted in the framework of the data collected in the Milan pilotWASN of the DYNAMAP LIFE project, with the use of three simulated acoustic impulse responses. The results show the clear influence of the evaluated coherence bandwidth of each of the simulated channels over real-life acoustic samples, which leads us to the conclusion that all raw acoustic samples have to be considered as wide-band. The results also depict a dependence of accumulated energy at the receiver with the coherence bandwidth of the channel. We conclude that, the higher the delay spread of the channel, the narrower the coherence bandwidth and the higher the distortion suffered by acoustic signals. Moreover, the accumulated energy of the received signal along the frequency axis tends to differ from the accumulated energy of the transmitted signal when facing narrow coherence bandwidth channels; whereas the accumulated energy along the time axis diverges from the accumulated transmitted energy when facing wide coherence bandwidth channels.

RESUMEN

Ambient Assisted Living (AAL) has become a powerful alternative to improving the life quality of elderly and partially dependent people in their own living environments. In this regard, tele-care and remote surveillance AAL applications have emerged as a hot research topic in this domain. These services aim to infer the patients' status by means of centralized architectures that collect data from a set of sensors deployed in their living environment. However, when the size of the scenario and number of patients to be monitored increase (e.g., residential areas, retirement homes), these systems typically struggle at processing all associated data and providing a reasonable output in real time. The purpose of this paper is to present a fog-inspired distributed architecture to collect, analyze and identify up to nine acoustic events that represent abnormal behavior or dangerous health conditions in large-scale scenarios. Specifically, the proposed platform collects data from a set of wireless acoustic sensors and runs an automatic two-stage audio event classification process to decide whether or not to trigger an alarm. Conducted experiments over a labeled dataset of 7116 s based on the priorities of the Fundació Ave Maria health experts have obtained an overall accuracy of 94.6%.

Asunto(s)

RESUMEN

Coverage maintenance is a bottleneck restricting the development of underwater acoustic sensor networks (UASNs). Since the energy of the nodes is limited, the coverage of UASNs may gradually decrease as the network operates. Thus, energy-saving coverage control is crucial for UASNs. To solve the above problems, this paper proposes a coverage-control strategy (referred to as ESACC) that establishes a sleep⁻wake scheduling mechanism based on the redundancy of deployment nodes. The strategy has two main parts: (1) Node sleep scheduling based on a memetic algorithm. To ensure network monitoring performance, only some nodes are scheduled to work, with redundant nodes in a low-power hibernation state, reducing energy consumption and prolonging the network lifetime. The goal of node scheduling is to find a minimum set of nodes that can cover the monitoring area, and a memetic algorithm can solve this problem. (2) Wake-up scheme. During network operation, sleeping nodes are woken to cover the dead nodes and maintain high coverage. This scheme not only reduces the network energy consumption but takes into account the monitoring coverage of the network. The experimental data show that ESACC performs better than current algorithms, and can improve the network life cycle while ensuring high coverage.

RESUMEN

One of the main aspects affecting the quality of life of people living in urban and suburban areas is the continuous exposure to high road traffic noise (RTN) levels. Nowadays, thanks to Wireless Acoustic Sensor Networks (WASN) noise in Smart Cities has started to be automatically mapped. To obtain a reliable picture of the RTN, those anomalous noise events (ANE) unrelated to road traffic (sirens, horns, people, etc.) should be removed from the noise map computation by means of an Anomalous Noise Event Detector (ANED). In Hybrid WASNs, with master-slave architecture, ANED should be implemented in both high-capacity (Hi-Cap) and low-capacity (Lo-Cap) sensors, following the same principle to obtain consistent results. This work presents an ANED version to run in real-time on μ Controller-based Lo-Cap sensors of a hybrid WASN, discriminating RTN from ANE through their Mel-based spectral energy differences. The experiments, considering 9 h and 8 min of real-life acoustic data from both urban and suburban environments, show the feasibility of the proposal both in terms of computational load and in classification accuracy. Specifically, the ANED Lo-Cap requires around 1 6 of the computational load of the ANED Hi-Cap, while classification accuracies are slightly lower (around 10%). However, preliminary analyses show that these results could be improved in around 4% in the future by means of considering optimal frequency selection.

RESUMEN

The underwater acoustic sensor network (UWASN) is a system that exchanges data between numerous sensor nodes deployed in the sea. The UWASN uses an underwater acoustic communication technique to exchange data. Therefore, it is important to design a robust system that will function even in severely fluctuating underwater communication conditions, along with variations in the ocean environment. In this paper, a new algorithm to find the optimal deployment positions of underwater sensor nodes is proposed. The algorithm uses the communication performance surface, which is a map showing the underwater acoustic communication performance of a targeted area. A virtual force-particle swarm optimization algorithm is then used as an optimization technique to find the optimal deployment positions of the sensor nodes, using the performance surface information to estimate the communication radii of the sensor nodes in each generation. The algorithm is evaluated by comparing simulation results between two different seasons (summer and winter) for an area located off the eastern coast of Korea as the selected targeted area.

RESUMEN

One of the main aspects affecting the quality of life of people living in urban and suburban areas is their continued exposure to high Road Traffic Noise (RTN) levels. Until now, noise measurements in cities have been performed by professionals, recording data in certain locations to build a noise map afterwards. However, the deployment of Wireless Acoustic Sensor Networks (WASN) has enabled automatic noise mapping in smart cities. In order to obtain a reliable picture of the RTN levels affecting citizens, Anomalous Noise Events (ANE) unrelated to road traffic should be removed from the noise map computation. To this aim, this paper introduces an Anomalous Noise Event Detector (ANED) designed to differentiate between RTN and ANE in real time within a predefined interval running on the distributed low-cost acoustic sensors of a WASN. The proposed ANED follows a two-class audio event detection and classification approach, instead of multi-class or one-class classification schemes, taking advantage of the collection of representative acoustic data in real-life environments. The experiments conducted within the DYNAMAP project, implemented on ARM-based acoustic sensors, show the feasibility of the proposal both in terms of computational cost and classification performance using standard Mel cepstral coefficients and Gaussian Mixture Models (GMM). The two-class GMM core classifier relatively improves the baseline universal GMM one-class classifier F1 measure by 18.7% and 31.8% for suburban and urban environments, respectively, within the 1-s integration interval. Nevertheless, according to the results, the classification performance of the current ANED implementation still has room for improvement.

RESUMEN

The consistent growth in human life expectancy during the recent years has driven governments and private organizations to increase the efforts in caring for the eldest segment of the population. These institutions have built hospitals and retirement homes that have been rapidly overfilled, making their associated maintenance and operating costs prohibitive. The latest advances in technology and communications envisage new ways to monitor those people with special needs at their own home, increasing their quality of life in a cost-affordable way. The purpose of this paper is to present an Ambient Assisted Living (AAL) platform able to analyze, identify, and detect specific acoustic events happening in daily life environments, which enables the medic staff to remotely track the status of every patient in real-time. Additionally, this tele-care proposal is validated through a proof-of-concept experiment that takes benefit of the capabilities of the NVIDIA Graphical Processing Unit running on a Jetson TK1 board to locally detect acoustic events. Conducted experiments demonstrate the feasibility of this approach by reaching an overall accuracy of 82% when identifying a set of 14 indoor environment events related to the domestic surveillance and patients' behaviour monitoring field. Obtained results encourage practitioners to keep working in this direction, and enable health care providers to remotely track the status of their patients in real-time with non-invasive methods.

Asunto(s)

RESUMEN

Noise pollution is a critical factor affecting public health, the relationship between road traffic noise (RTN) and several diseases in urban areas being especially disturbing. The Environmental Noise Directive 2002/49/EC and the CNOSSOS-EU framework are the main instruments of the European Union to identify and combat noise pollution, requiring Member States to compose and publish noise maps and noise management action plans every five years. Nowadays, the noise maps are starting to be tailored by means of Wireless Acoustic Sensor Networks (WASN). In order to exclusively monitor the impact of RTN on the well-being of citizens through WASN-based approaches, those noise sources unrelated to RTN denoted as Anomalous Noise Events (ANEs) should be removed from the noise map generation. This paper introduces an analysis methodology considering both Signal-to-Noise Ratio (SNR) and duration of ANEs to evaluate their impact on the A-weighted equivalent RTN level calculation for different integration times. The experiments conducted on 9 h of real-life data from the WASN-based DYNAMAP project show that both individual high-impact events and aggregated medium-impact events bias significantly the equivalent noise levels of the RTN map, making any derived study about public health impact inaccurate.

Asunto(s)

RESUMEN

Underwater Acoustic Sensor Networks (UASNs) have attracted increasing interest in recent years due to their extensive commercial and military applications. However, the harsh underwater channel causes many challenges for the design of reliable underwater data transport protocol. In this paper, we propose an energy efficient data transport protocol based on network coding and hybrid automatic repeat request (NCHARQ) to ensure reliability, efficiency and availability in UASNs. Moreover, an adaptive window length estimation algorithm is designed to optimize the throughput and energy consumption tradeoff. The algorithm can adaptively change the code rate and can be insensitive to the environment change. Extensive simulations and analysis show that NCHARQ significantly reduces energy consumption with short end-to-end delay.