RESUMEN

Dimeric acceptors are expected to satisfy both excellent power conversion efficiency (PCE) and operational stability of organic solar cells (OSCs). However, comparing to highly planar and symmetrical monomer-like acceptors, the quite different steric/spatial configurations of dimeric acceptors affect device outcomes greatly. Herein, on basis of the same dimeric molecular platform that constructed by bridging central units of two monomer-like acceptor, diverse substituents (─OCH3 for D1, ─CH3 for D2, and ─CF3 for D3) are grafted on central units to regulate the three dimensions (3D) geometries of dimeric acceptors delicately. A systematic investigation reveals the substituent-dependent variation of energy level, absorption, and molecular packing behavior. Consequently, D2 acceptor, characteristic of more favorable configuration, affords a superior film morphology and charge transfer/transport dynamics in resulting OSCs, thus yielding an excellent PCE of 17.50% along with a good long-term stability. This work manifests the crucially important role of central substituents in constructing high-performance dimeric acceptors.

RESUMEN

The dimerization of small molecule acceptors (SMAs) holds significant potential by combining the advantages of both SMAs and polymer acceptors in realizing high power conversion efficiency (PCE) and operational stability in organic solar cells (OSCs). However, advancements in the selection and innovation of dimeric linkers are still challenging in enhancing their performance. In this study, three new dimeric acceptors, namely DY-Ar-4, DY-Ar-5, and DY-Ar-6 are synthesized, by linking two Y-series SMA subunits via an "end-to-end" strategy using flexible spacers (octyl, decyl, and dodecyl, respectively). The influence of spacer lengths on device performance is systematically investigated. The results indicate that DY-Ar-5 exhibits more compact and ordered packing, leading to an optimal morphology. OSCs based on PM6: DY-Ar-5 achieves a maximum PCE of 15.76%, attributes to enhance and balance carrier mobility, and reduce carrier recombination. This dimerization strategy using suitable non-conjugated linking units provides a rational principle for designing high-performance non-fullerene acceptors.

RESUMEN

This study underscores the significance of precisely manipulating the morphology of the active layer in organic solar cells (OSCs). By blending polymer donors of D18 with varying molecular weights, a multiscale interpenetrating fiber network structure within the active layer is successfully created. The introduction of 10% low molecular weight D18 (LW-D18) into high molecular weight D18 (HW-D18) produces MIX-D18, which exhibits an extended exciton diffusion distance and orderly molecular stacking. Devices utilizing MIX-D18 demonstrate superior electron and hole transport, improves exciton dissociation, enhances charge collection efficiency, and reduces trap-assisted recombination compared to the other two materials. Through the use of the nonfullerene acceptor L8-BO, a remarkable power conversion efficiency (PCE) of 20.0% is achieved. This methodology, which integrates the favorable attributes of high and low molecular weight polymers, opens a new avenue for enhancing the performance of OSCs.

RESUMEN

The performance of organic solar cell (OSC) devices has been significantly enhanced by the dramatic evolution of A-D-A type non-fullerene acceptors (NFAs). Nevertheless, the structure-property-performance relationship of NFAs in the OSC device is unclear. Here, the intrinsic design factors of isomeric, fluorination and π-conjunction curtailing on the photophysical properties of benzodi (thienopyran) (BDTP) (named NBDTP-M, NBDTTP-M, NBDTP-Fin, and NBDTP-Fout)-based NFAs are discussed. The results show that fluorination on the terminal group of NBDTP-Fout could effectively decrease the highest occupied orbital (HOMO) energy level and the lowest unoccupied orbital (LUMO) energy level. And the long π-conjugated donor unit for NBDTTP-M could increase the HOMO energy level and bring a small HOMO-LUMO energy bandgap. Meanwhile, the substitution of external oxygen atoms and the fluorine atoms in the terminal group could introduce positive changes to the electrostatic potential of the NBDTP-Fout, favouring the charge separation at the donor/acceptor interface. Moreover, the structural design of external oxygen atom substitution, fluorination on the terminal group and curtailed π-conjugated donor unit could decrease the electron vibration-coupling of exciton diffusion, exciton dissociation and electronic transfer processes. The suppression of the exciton decay and charge recombination in those high-performance NFAs indicate that the investigated molecular designs could be effective for further improvement of OSCs.

RESUMEN

The strategy of isomerization is known for its simple yet effective role in optimizing molecular configuration and enhancing the power conversion efficiency (PCE) of organic solar cells (OSCs). However, the impact of isomerization on the design of dimer acceptors has been rarely investigated, and the relationship between the chemical structure and optoelectronic property remains unclear. In this study, we designed and synthesized two dimer acceptor isomers named D-TPh and D-TN, which differ in the positional arrangement of their end capping groups. Compared to D-TN, D-TPh exhibited enhanced backbone planarity, elevated lowest unoccupied molecular orbital energy level, and more ordered molecular stacking. Consequently, the OSC device based on PM6:D-TPh achieved a PCE of 19.05%, higher than that (PCE = 18.42%) of the device based on PM6:D-TN. Large-area PM6:D-TPh devices (1 cm²) yielded a PCE of 18.0%. More importantly, the extrapolated T80 lifetime of the PM6:D-TPh device is over 2800 h with MPP tracking under continuous one-sun illumination. These results suggest that isomerization strategy is an effective way to optimize the molecular configuration of dimer acceptors for the fabrication of high-efficiency and stable OSCs.

RESUMEN

The solution aggregation structure of conjugated polymers is crucial to the morphology and resultant optoelectronic properties of organic electronics and is of considerable interest in the field. Precise characterizations of the solution aggregation structures of organic photovoltaic (OPV) blends and their temperature-dependent variations remain challenging. In this work, the temperature-dependent solution aggregation structures of three representative high-efficiency OPV blends using small-angle X-ray/neutron scattering are systematically probed. Three cases of solution processing resiliency are elucidated in state-of-the-art OPV blends. The exceptional processing resiliency of high-efficiency PBQx-TF blends can be attributed to the minimal changes in the multiscale solution aggregation structure at elevated temperatures. Importantly, a new parameter, the percentage of acceptors distributed within polymer aggregates (Ф), for the first time in OPV blend solution, establishes a direct correlation between Ф and performance is quantified. The device performance is well correlated with the Kuhn length of the cylinder related to polymer aggregates L1 at the small scale and the Ф at the large scale. Optimal device performance is achieved with L1 at ≈30 nm and Ф within the range of 60 ± 5%. This study represents a significant advancement in the aggregation structure research of organic electronics.

RESUMEN

As the simplest oligomeric acceptors, dimerized acceptors (DAs) are easier to synthesize, and more importantly, they can retain good intermolecular interaction and photovoltaic properties of their parent small-molecule acceptors (SMAs). Nevertheless, currently most efficient DAs are derived from banana-shaped acceptors and they might suffer from inferior device stability with high diffusion coefficients. Herein, we design and synthesize two planar DAs (DMT-FH and DMT-HF) by bridging two linear-shaped M-series SMAs with a thiophene unit. The effects of fluorination position on the diffusion coefficients, power conversion efficiencies (PCEs) and stability of the DAs are systematically studied. Our results suggest that DMT-HF with fluorination on the ending indanone groups shows enhanced intermolecular interactions, improved PCE and stability compared with the counterpart (DMT-FH) with fluorination on the central indanone groups. Further optimization on the DMT-HF-based devices yields an outstanding PCE of 17.17%, which is the highest among all linear-shaped SMA-based DAs. Notably, with the low diffusion coefficient (3.36×10-24 cm2 s-1) of DMT-HF, the resulting device retains over 93% of the initial PCE after 5000 h of continuous heating at 85 oC, suggesting its excellent thermal stability. The results highlight the importance of intermolecular interaction and fluorination for achieving efficient and stable polymer solar cells.

RESUMEN

Herein, the indolonaphthyridine-based molecules (INDTD1-INDTD8) with A1-π-A2-π-A1 configuration were designed by the end-capped modification of INDTR reference with various acceptors. The density functional theory (DFT) and time-dependent DFT (TD-DFT) analyses at M06/6-31G(d,p) level were reported in this research to explore their optoelectronic and photovoltaic features. Their geometrical structures were initially optimized at the afore-said level and followed by various calculations such as the frontier molecular orbitals (FMOs), UV-Visible, density of states (DOS), transition density matrix (TDM), binding energy (Eb), open circuit voltage (Voc) and fill factor (FF). Moreover, their global reactivity parameters (GRPs) were depicted by using the HOMO-LUMO band gaps obtained from the FMOs study. The tailored molecules demonstrated lower band gaps (2.183-2.269 eV) than INDTR (2.288 eV). They also showed bathochromic shifts in the visible region in chloroform (735.937-762.318 nm) and gas phase (710.384-729.571 nm) as compared to INDTR (724.710 and 698.498 nm, respectively). Further, intramolecular charge transfer (ICT) was demonstrated via the DOS and TDM graphical maps. Among all the entitled chromophores, INDTD7 showed significantly reduced band gap (2.183 eV), red-shifted absorption value (760.914 nm) in chloroform solvent and minimal Eb value (0.554 eV). The presence of -SO3H groups on the terminal acceptors of INDTD7  may enhance the mobility of charges. The results suggested that the newly designed chromophores can be effective candidates for the future organic solar cell applications. Moreover, this study may encourage the experimentalists to develop photovoltaic materials.

RESUMEN

High-performance organic solar cells often rely on halogen-containing solvents, which restrict the photovoltaic industry. Therefore, it is imperative to develop efficient organic photovoltaic materials compatible with halogen-free solvents. Herein, a series of benzo[a]phenazine (BP)-core-based small-molecule acceptors (SMAs) achieved through an isomerization chlorination strategy is presented, comprising unchlorinated NA1, 10-chlorine substituted NA2, 8-chlorine substituted NA3, and 7-chlorine substituted NA4. Theoretical simulations highlight NA3's superior orbit overlap length and tight molecular packing, attributed to interactions between the end group and BP unit. Furthermore, NA3 demonstrates dense 3D network structures and a record electronic coupling of 104.5 meV. These characteristics empower the ortho-xylene (o-XY) processed PM6:NA3 device with superior power conversion efficiency (PCE) of 18.94%, surpassing PM6:NA1 (15.34%), PM6:NA2 (7.18%), and PM6:NA4 (16.02%). Notably, the significantly lower PCE in the PM6:NA2 device is attributed to excessive self-aggregation characteristics of NA2 in o-XY. Importantly, the incorporation of D18-Cl into the PM6:NA3 binary blend enhances crystallographic ordering and increases the exciton diffusion length of the donor phase, resulting in a ternary device efficiency of 19.75% (certified as 19.39%). These findings underscore the significance of incorporating new electron-deficient units in the design of efficient SMAs tailored for environmentally benign solvent processing of OSCs.

RESUMEN

Bioremediation provides an environmentally sound solution for hydrocarbon removal. Although bioremediation under anoxic conditions is slow, it can be coupled with methanogenesis and is suitable for energy recovery. By altering conditions and supplementing alternative terminal electron acceptors to the system to induce syntrophic partners of the methanogens, this process can be enhanced. In this study, we investigated a hydrocarbon-degrading microbial community derived from chronically contaminated soil. Various hydrocarbon mixtures were used during our experiments in the presence of different electron acceptors. In addition, we performed whole metagenome sequencing to identify the main actors of hydrocarbon biodegradation in the samples. Our results showed that the addition of ferric ions or sulphate increased the methane yield. Furthermore, the addition of CO2, ferric ion or sulphate enhanced the biodegradation of alkanes. A significant increase in biodegradation was observed in the presence of ferric ions or sulphate in the case of all aromatic components, while naphthalene and phenanthrene degradation was also enhanced by CO2. Metagenome analysis revealed that Cellulomonas sp. is the most abundant in the presence of alkanes, while Ruminococcus and Faecalibacterium spp. are prevalent in aromatics-supplemented samples. From the recovery of 25 genomes, it was concluded that the main pathway of hydrocarbon activation was fumarate addition in both Cellulomonas, Ruminococcus and Faecalibacterium. Chloroflexota bacteria can utilise the central metabolites of aromatics biodegradation via ATP-independent benzoyl-CoA reduction. KEY POINTS: • Methanogenesis and hydrocarbon biodegradation were enhanced by Fe3+ or SO42- • Cellulomonas, Ruminococcus and Faecalibacterium can be candidates for the main hydrocarbon degraders • Chloroflexota bacteria can utilise the central metabolites of aromatics degradation.

Asunto(s)

RESUMEN

The insufficient abundance of electron acceptors for ammonia during electron transfer in constructed wetlands (CWs) results in low nitrification rates. This study developed a green, low-carbon CWs enhanced by a bio-electrochemical systems (BESs-CWs) to achieve efficient ammonia (NH4+-N) removal. Electrode enhancement significantly promoted NH4+-N removal. Compared with traditional CWs, the average removal efficiency of NH4+-N in the BESs-CWs increased from 62.9 % to 90.6 %. The intermittent voltage driven by the photovoltaic power system caused minimal plant stress. However, electrode enhancement significantly affected microbial communities involved in short-path nitrification and denitrification within the biofilm. Specifically, the removal rate of NH4+-N by BESs-CWs under electrode enhancement was increased by 27.7 % compared to traditional CWs, enhancing the electron output of NH4+-N in the BESs-CWs. This system provides a method of ammonia nitration for CWs under poor electron acceptor conditions.

Asunto(s)

RESUMEN

The development of nonfullerene acceptors (NFAs), represented by ITIC, has contributed to improving the power conversion efficiency (PCE) of organic solar cells (OSCs). Although tuning the electronic structures to reduce the exciton binding energy (Eb) is considered to promote photocharge generation, a rational molecular design for NFAs has not been established. In this study, we designed and developed two ITIC-based NFAs bearing spiro-substituted bithiophene or biphenyl units (named SpiroT-DCI and SpiroF-DCI) to tune the frontier molecular orbital (FMO) distribution of NFAs. While the highest occupied molecular orbitals (HOMOs) of SpiroF-DCI and ITIC are delocalized in the main π-conjugated framework, the HOMO of SpiroT-DCI is distributed on the bithiophene unit. Reflecting this difference, SpiroT-DCI exhibits a smaller Eb than either SpiroF-DCI or ITIC, and exhibits greater external quantum efficiency in single-component OSCs. Furthermore, SpiroT-DCI shows improved PCEs for bulk-heterojunction OSCs with a donor of PBDB-T, compared with that of either SpiroT-DCI or ITIC. Time-resolved spectroscopy measurements show that the photo-induced intermolecular charge separation is effective even in pristine SpiroT-DCI films. This study highlights the introduction of spiro-substituted bithiophene units that are effective in tuning the FMOs of ITIC, which is desirable for reducing the Eb and improving the PCE in OSCs.

RESUMEN

This study reports the successful design and synthesis of two novel polymerized nonfused ring electron acceptors, P-2BTh and P-2BTh-F, derived from the high-performance nonfused ring electron acceptor, 2BTh-2F. Prepared via Stille polymerization, these polymers feature thiophene and fluorinated thiophene as π-bridge units. Notably, P-2BTh-F, with difluorothiophene as the π-bridge, exhibits a more planar backbone and red-shifted absorption spectrum compared with P-2BTh. When employed in organic solar cells (OSCs) with PBDB-T as the donor material, P-2BTh-F-based devices demonstrate an outstanding power conversion efficiency (PCE) of over 11%, exceeding the 8.7% achieved by P-2BTh-based devices. Furthermore, all-polymer solar cells utilizing PBDB-T:P-2BTh-F exhibit superior storage stability. Additionally, P-2BTh-F was explored as a functional additive in a high-performance binary system, enhancing stability while maintaining comparable PCE (19.45%). This strategy offers a cost-effective approach for fabricating highly efficient and stable binary and ternary organic solar cells, opening new horizons for cost-effective and durable solar cell development.

RESUMEN

Conformational isomerism of organic photovoltaic materials has a profound impact on their molecular packing and therefore performance of polymer solar cells (PSCs). However, the conformations of oligomeric acceptors (OAs) are mostly predicted by simulations rather than experimental determinations. Herein, the stereochemical S-shaped structure of two dimeric-type acceptor molecules, V-DYIC and V-DYIC-4F, is first confirmed with different end groups (IC for V-DYIC and IC-2F for V-DYIC-4F), incorporating vinylene linkage for connecting the distinct state-of-the-art small molecule acceptor Y-segments. Through the synthetic control of fluorination sites adjacent to the vinyl-linker, S-shaped the conformation by NMR experiments is validated. Compared to the O-shaped dimer, S-shaped conformation results in enhanced lamellar order and reduced nonradiative recombination losses. The optimal acceptor, V-DYIC-4F, achieved a champion efficiency of 18.10% with the lowest energy loss of 0.556 eV in its devices paired with PM6 due to their efficient carrier transport, and suppressed recombination compared to other devices, being attributed to the synergistic effect of conformation and end group fluorination. The insights gained in this work contribute valuable knowledge of both synthetic control and structural determination of OAs, providing strategic design guidelines for the future development of dimeric acceptors toward high-efficiency PSCs.

RESUMEN

Dimer acceptors in organic solar cells (OSCs) offer distinct advantages, including a well-defined molecular structure and excellent batch-to-batch reproducibility. Their high glass transition temperature (Tg) aids in achieving an optimal kinetic morphology, thereby enhancing device stability. Currently, most of dimer acceptor materials are linked with conjugated units in order to obtain high power conversion efficiencies (PCEs). In this study, different from previous works on conjugation-linked dimer acceptors, a novel series of dimer acceptors are synthesized (named T1, T4, T6, and T12), each linked with different flexible alkyl linkers, and investigated their PCEs, device stability, and flexibility robustness. When blended with PM6, the T6-based device achieves a PCE of 17.09%, comparable to the fully conjugated T0-based device's PCE of 17.12%. The molecular dynamics simulations and density functional theory calculations suggested that flexible conjugation-broken linkers (FCBLs) promote intermolecular electronic couplings, thereby maintaining good electron mobilities of dimer acceptors. Notably, the T6-based device exhibits impressive long-term stability with a T80 lifetime of 1427 h, while in the T0-based device, T80 is only 350 h. The present work has thus established the relationship between the length of flexible alkyl linkers in such dimer acceptors and the performance and stability of OSCs, which is important to further designing new materials for the fabrication of efficient and stable OSCs.

RESUMEN

This study successfully designed and synthesized two nonfused ring electron acceptors, 412-6F and 412-6Cl, modified with fluorine and chlorine substituents, respectively. Single-crystal analysis revealed that 412-6F possesses a planar molecular backbone and exhibits pronounced dipole-dipole interactions between the fluorine atoms on the lateral phenyl groups and the carbonyl oxygen atoms on the end groups. This specific interaction promotes dense end-group stacking, leading to a reduced interlayer spacing. Improved crystallinity and coherence length are observed in the D18:412-6F blend film. Conversely, 412-6Cl adopts a more distorted configuration and lacks these interactions. As a result, the organic solar cell (OSC) based on D18:412-6F achieved a remarkable power conversion efficiency of 18.03%, surpassing the performance of the D18:412-6Cl OSC. This underscores the importance of designing novel acceptors with beneficial intermolecular interactions to enhance OSC efficiency, thus providing a new direction for organic photovoltaic advancement.

RESUMEN

Benzophenone skeletons containing a carbonyl unit (O=C) have been widely used as electron acceptors in the thermally activated delayed fluorescence (TADF) materials. Herein, we present a novel molecular design concept for TADF materials by transitioning from a carbonyl to an amide (O=C-N) skeleton as the acceptor. The amide unit, compared to its carbonyl counterpart, offers a more stable electronic configuration. Leveraging this insight, we have developed a series of high-performance TADF molecules based on benzoyl carbazole and carbazoline acceptors. These molecules exhibit exceptionally small singlet-triplet energy gaps and pronounced aggregation-enhanced emission properties, achieving photoluminescence quantum yields in neat films as high as 99 %. Consequently, these materials serve as efficient emitters in non-doped organic light-eimtting diodes (OLEDs), reaching a maximum quantum efficiency (EQEmax) of up to 26.0 %, significantly higher than the 17.0 % obtained with benzophenone acceptor-based TADF molecules. Additionally, they have been used as TADF hosts in narrowband red fluorescent OLEDs, setting a record-high EQEmax of 22.4 %.

RESUMEN

With the rapid development of non-fullerene acceptors (NFAs), the power conversion efficiency (PCE) of organic solar cells (OSCs) is increasing. According to their different chemical structures, NFAs can initially be divided into two categories: small molecule acceptors (SMAs) and polymerized small molecule acceptors (PSMAs). Due to the strong absorption capacity and controllable energy levels, the PCE of devices based on SMAs has approached 20%. Compared with SMAs, PSMAs have advantages in stability and flexibility, and the PCE of PSMA-based devices has exceeded 18%. However, the higher synthesis cost and lower batch repeatability hinder its further development. Recently, the concept of giant molecule acceptors (GMAs) has been proposed. These materials have a clear molecular structure and are considered novel acceptor materials that combine the advantages of SMAs and PSMAs. Currently, the PCE of devices based on GMAs has exceeded 19%. In this review, we will introduce the latest developments in SMAs, PSMAs, and GMAs. Then, the advantages of GMAs and the relationship between their structure and performance will be analyzed. In the end, perspectives on the opportunities and challenges of these materials are provided, which could inspire further development of NFAs for advanced OSCs.

RESUMEN

We report the synthesis and characterization of naphthalene and anthracene scaffolds end-capped by cyclic imides. The solid-state structures of the N-phenyl derivatives, determined by X-ray crystallography, reveal changes in packing preference based on the number of aromatic rings in the core. The optical and electronic properties of the title compounds compare favorably with other previously described isomers and expand the toolbox of electron-deficient aromatic compounds available to organic materials chemists.

RESUMEN

Compared to the bulk heterojunction (BHJ) devices, the quasiplanar heterojunction (Q-PHJ) exhibits a more stable morphology and superior charge transfer performance. To achieve both high efficiency and long-term stability, it is necessary to design new materials for Q-PHJ devices. In this study, QxIC-CF3 and QxIC-CH3 are designed and synthesized for the first time. The trifluoromethylation of the central core exerts a modulatory effect on the molecular stacking pattern, leveraging the strong electrostatic potential and intermolecular interactions. Compared with QxIC-CH3, the single crystal structure reveals that QxIC-CF3 exhibits a more compact 2D linear stacking behavior. These benefits, combined with the separated electron and hole transport channels in Q-PHJ device, lead to increased charge mobility and reduced energy loss. The devices based on D18/QxIC-CF3 exhibit an efficiency of 18.1%, which is the highest power conversion efficiency (PCE) for Q-PHJ to date. Additionally, the thermodynamic stability of the active layer morphology enhances the lifespan of the aforementioned devices under illumination conditions. Specifically, the T80 is 420 h, which is nearly twice that of the renowned Y6-based BHJ device (T80 = 220 h). By combining the advantages of the trifluoromethylation and Q-PHJ device, efficient and stable organic solar cell devices can be constructed.