RESUMEN
OBJECTIVES: The objectives of this study were to assess the accuracy of working length determination using 3 electronic apex locators and direct digital radiography and to compare the results with those obtained using the visual method (control measurement). STUDY DESIGN: Twenty extracted human maxillary premolars were selected: 17 two-rooted and 3 single-rooted (total of 37 canals). Working length was measured using electronic apex locators Elements Diagnostic, Root ZX, and Just II. Subsequently, teeth were positioned in the alveolar bone of a dry skull and submitted to direct digital radiography. A variation of ±1 mm was considered as acceptable. Results were analyzed using the Wilcoxon and the χ(2) tests. RESULTS: Results presented an accuracy of 94.6% for Elements Diagnostic, 91.9% for Root ZX, 73.0% for Just II, and 64.9% for direct digital radiography when considering the margin of ±1 mm in relation to the control measurement. Comparisons with the actual control measurements resulted in accuracy results of 13.51%, 13.51%, 10.10%, and 2.70%, respectively. CONCLUSIONS: Root ZX and Elements Diagnostic are more accurate in determining working length when compared with Just II and Schick direct digital radiography.
Asunto(s)
Cavidad Pulpar/anatomía & histología , Odontometría/instrumentación , Radiografía Dental Digital , Preparación del Conducto Radicular/instrumentación , Ápice del Diente/anatomía & histología , Diente Premolar/anatomía & histología , Electrónica/instrumentación , Diseño de Equipo , Humanos , Odontometría/estadística & datos numéricos , Radiografía Dental Digital/estadística & datos numéricosRESUMEN
INTRODUCTION: The aim of this study was to assess the occurrence of apical root transportation after the use of ProTaper Universal rotary files sizes 3 (F3) and 4 (F4). METHODS: Instruments were worked to the apex of the original canal, always by the same operator. Digital subtraction radiography images were produced in buccolingual and mesiodistal projections. A total of 25 radiographs were taken from root canals of human maxillary first molars with curvatures varying from 23-31 degrees. Quantitative data were analyzed by intraclass correlation coefficient and Wilcoxon nonparametric test (P = .05). RESULTS: Buccolingual images revealed a significantly higher degree of apical transportation associated with F4 instruments when compared with F3 instruments in relation to the original canal (Wilcoxon test, P = .007). No significant difference was observed in mesiodistal images (P = .492). CONCLUSIONS: F3 instruments should be used with care in curved canals, and F4 instruments should be avoided in apical third preparation of curved canals.
Asunto(s)
Cavidad Pulpar/diagnóstico por imagen , Radiografía Dental Digital/métodos , Preparación del Conducto Radicular/instrumentación , Técnica de Sustracción , Ápice del Diente/diagnóstico por imagen , Cavidad Pulpar/anatomía & histología , Humanos , Ensayo de Materiales , Diente Molar/diagnóstico por imagen , Odontometría , Preparación del Conducto Radicular/métodos , Ápice del Diente/anatomía & histologíaRESUMEN
OBJECTIVES: This study aimed to assess the apical surface morphology of maxillary central incisors resected 3.0 mm from the tooth apex using Zekrya burs or Er:YAG laser, with or without subsequent direct Nd:YAG laser irradiation (apical and buccal surfaces) and indirect irradiation (palatal surface). STUDY DESIGN: Forty maxillary central incisors were instrumented and obturated. The roots were divided into 4 groups according to the root resection method (Zekrya bur or Er:YAG laser - 1.8 W, 450 mJ, 4 Hz, 113 J/cm(2)) and further surface treatment (none or Nd:YAG laser - 2.0 W, 100 mJ, 20 Hz, 124 J/cm(2)). The teeth were prepared for SEM analysis. Scores ranging from 1 to 4 were attributed to cut quality and morphological changes. The data were analyzed by the Kruskal-Wallis test and by Dunn's test. RESULTS: SEM images showed irregular surfaces on the apical portions resected with Zekrya burs, with smear layer and grooves in the resected dentine and slight gutta-percha displacement and plasticization. On the other hand, apicectomies carried out with Er:YAG laser showed morphological changes compatible with ablated dentine, with rough surfaces and craters. In spite of the presence of plasticized gutta-percha, with the presence of bubbles, an irregular adaptation of the filling material to the root walls was also observed. Direct Nd:YAG laser irradiation of the apical and buccal surfaces of the resected roots resulted in areas of resolidification and fusion in the dentine and cementum, with a vitrified aspect; indirect Nd:YAG laser irradiation of the palatal surfaces yielded a lower number of changes in the cementum, with irregular resolidification areas. CONCLUSIONS: There were no differences in terms of cut quality between the use of burs and Er:YAG laser or between the 2 surfaces (apical and buccal) treated with Nd:YAG laser with direct irradiation. However, morphological changes were significantly less frequent on surfaces submitted to indirect irradiation (palatal) when compared with those directly irradiated.
Asunto(s)
Apicectomía/instrumentación , Cemento Dental/patología , Dentina/patología , Terapia por Láser/métodos , Láseres de Estado Sólido/uso terapéutico , Terapia por Luz de Baja Intensidad/métodos , Apicectomía/métodos , Cemento Dental/efectos de la radiación , Adaptación Marginal Dental , Dentina/efectos de la radiación , Gutapercha/química , Gutapercha/uso terapéutico , Humanos , Incisivo/efectos de la radiación , Incisivo/cirugía , Microscopía Electrónica de Rastreo , Materiales de Obturación del Conducto Radicular/química , Materiales de Obturación del Conducto Radicular/uso terapéutico , Irrigantes del Conducto Radicular/uso terapéutico , Obturación del Conducto Radicular/métodos , Preparación del Conducto Radicular/métodos , Método Simple Ciego , Capa de Barro Dentinario , Propiedades de Superficie , Ápice del Diente/efectos de la radiación , Ápice del Diente/cirugíaRESUMEN
OBJECTIVE: To evaluate the influence of 810-nm-diode laser irradiation, applied before root canal filling, on apical sealing ability of three different resin-based sealers (AH Plus, EndoRez, and RealSeal). BACKGROUND: Lasers have been widely used in endodontics. The dentin wall changes caused by laser irradiation could improve the sealing ability of endodontic cements. METHODS: Sixty single-rooted human teeth were divided into six groups, according to the endodontic sealer used and previous 810-nm-diode laser irradiation. The protocol for laser irradiation was 2.5 W in a continuous wave, in scanning mode, with four irradiations per tooth. After sample preparation, they were analyzed according to apical leakage with silver nitrate impregnation. RESULTS: The RealSeal sealer achieved minimum leakage rates (1.24 mm), with significant differences at the 1% level (Tukey's test, p<0.01) from AH Plus (1.84 mm) in nonirradiated groups. When the laser was used, there were also significant differences at the 5% level (p<0.05) between irradiated groups (1.31 and 1.78 mm, respectively). CONCLUSION: The 810-nm-diode laser irradiation did not promote significant differences in apical leakage.
Asunto(s)
Resinas Compuestas/efectos de la radiación , Filtración Dental/prevención & control , Láseres de Semiconductores , Materiales de Obturación del Conducto Radicular , Preparación del Conducto Radicular/instrumentación , Ápice del Diente/efectos de la radiación , Análisis de Varianza , Recubrimiento Dental Adhesivo , Dentina/efectos de la radiación , Dentina/ultraestructura , Resinas Epoxi , Humanos , Distribución Aleatoria , Propiedades de Superficie , Ápice del Diente/ultraestructuraRESUMEN
OBJECTIVE: Our goal was to compare the in vivo biocompatibility of dental root surfaces submitted to four different treatments after tooth avulsion followed by implantation into rat subcutaneous tissue. BACKGROUND DATA: Dental root surface preparation prior to replanting teeth remains a challenge for endodontists. Root surface changes made by Nd:YAG irradiation could be an alternative preparation. METHODS: Forty-eight freshly extracted human dental roots were randomly divided into four treatment groups prior to implantation into rat subcutaneous tissue: G1, dry root, left in the environment up to 3 h; G2, the same treatment as G1, followed by a soaking treatment in a 2.4% sodium fluoride solution (pH 5.5); G3, root soaked in physiologic saline after avulsion for 72 h; G4, the same treatment as G1, followed by Nd:YAG laser irradiation (2.0 W, 20 Hz, 100 mJ, and 124.34 J/cm(2)). The animals were sacrificed 1, 7, and 45 d later. Histological and scanning electron microscopy analyses were done. RESULTS: All dental roots were involved and in intimate contact with connective tissue capsules of variable thicknesses. Differences were observed in the degree of inflammation and in connective tissue maturation. In G3 the inflammatory infiltrate was maintained for 45 d, whereas the Nd:YAG laser irradiation (G4) led to milder responses. The overall aspects of the root surfaces were similar, except by the irradiated roots, where fusion and resolidification of the root surface covering the dentinal tubules were observed. CONCLUSION: Nd:YAG laser irradiation improves the biocompatibility of dental root and thus could be an alternative treatment of dental root prior to replantation.
Asunto(s)
Terapia por Láser , Avulsión de Diente/terapia , Preparación del Diente/métodos , Reimplante Dental , Raíz del Diente/efectos de la radiación , Animales , Humanos , Láseres de Estado Sólido , Masculino , Ensayo de Materiales , Ratas , Ratas Wistar , Tejido SubcutáneoRESUMEN
Calcium hydroxide dressing residuals can compromise endodontic sealing. This study evaluated the cleaning efficacy of different endodontic irrigants in removing calcium hydroxide by SEM image analysis. Fifty-four single-rooted mandibular premolars were instrumented to a master apical file #60 and dressed with calcium hydroxide. After 36 hours, the teeth were reopened and Ca(OH)(2) medication was removed by 5 different experimental groups: 0.5% NaOCl (G1), EDTA-C (G2), citric acid (G3), EDTA-T (G4), and re-instrumentation with MAF using NaOCl and lubrificant, followed by EDTA-T (G5). The roots were split in the buccal-lingual direction and prepared for SEM analysis in cervical, middle, and apical thirds (9, 6, and 3mm from the apex). Five blinded examiners evaluated the wall cleanliness using a scale from 1 to 5. Statistical analysis was performed using Kruskal-Wallis at 5% level of significance. Group G5 had the best results in all thirds, with significant statistical differences compared to all other groups in the middle and coronal third, and to G1 in the apical third. On the other hand, G1, only flushed with NaOCl, had the worst results, with statistical differences in all thirds compared to the other groups. The best cleanliness was achieved by G4 and G5 groups. The recapitulation of MAF in combination with irrigants improved the removal of calcium hydroxide medication better than an irrigant flush alone.
Asunto(s)
Hidróxido de Calcio , Materiales de Obturación del Conducto Radicular , Irrigantes del Conducto Radicular , Preparación del Conducto Radicular/instrumentación , Diente Premolar , Ácido Cítrico , Restauración Dental Provisional , Ácido Edético , Humanos , Microscopía Electrónica de Rastreo , Hipoclorito de SodioRESUMEN
OBJECTIVE: To verify the effects of laser energy on intracanal dentin surfaces, by analyzing the morphologic changes and removal of debris in the apical third of 30 extracted human teeth, prepared and irradiated with the Nd:YAG laser and diode laser. BACKGROUND DATA: Lasers have been widely used in endodontics. The morphologic changes in dentin walls caused by Nd:YAG and diode laser irradiation could improve apical seals and cleanliness. MATERIALS AND METHODS: The protocol used for Nd:YAG laser irradiation was 1.5 W, 100 mJ, and 15 Hz, in pulsed mode, and for diode laser was 2.5 W in continuous mode. Each specimen was irradiated four times at a speed of 2 mm/sec with a 20-sec interval between applications. Five calibrated examiners scored the morphologic changes and debris removal on a 4-point scale. RESULTS: In analyzing the scores, there were no statistically significant differences between the two types of laser for either parameter, according to Kruskal-Wallis testing at p = 0.05. The SEM images showed fusion and resolidification of the dentin surface, with partial removal of debris on the specimens irradiated with the Nd:YAG laser and the diode laser, compared with controls. CONCLUSION: Both lasers promote morphologic changes and debris removal. These alterations of the dentin surface appeared to be more evident in the Nd:YAG laser group, but the diode laser group showed more uniform changes.
Asunto(s)
Dentina/efectos de la radiación , Láseres de Semiconductores/uso terapéutico , Láseres de Estado Sólido/uso terapéutico , Dentina/citología , Humanos , Técnicas In Vitro , Propiedades de SuperficieRESUMEN
OBJECTIVE: This study aims to evaluate the influence of Nd:YAG and diode laser irradiation on apical sealing when applied before root canal filling done with two different resin-based cements (AH Plus and EndoREZ). BACKGROUND DATA: Lasers have been widely used in endodontics. The morphologic changes in dentin walls caused by Nd:YAG and diode laser irradiation could improve sealing ability of endodontic cements. METHODS: Eighty canine teeth were analyzed by apical leakage of methylene blue dye and by scanning electron microscope (SEM) images of the filling's adaptation to the apical third dentin walls. The laser irradiation parameters for the Nd:YAG laser were 100 mJ, 15 Hz, and 1.5 W, and for the diode laser was 2.5 W (continuous mode). RESULTS: The apical leakage results showed statistically significant differences at the 5% level of significance (Tukey's test, p < 0.05) among the different root canal wall treatments, independently of the root canal filling cement used. The cements also showed significant differences between them on the lased groups. The SEM analysis revealed better filling adaptation for AH Plus and the Nd:YAG laser group, confirming the microleakage results. CONCLUSION: We concluded that the combination of the Nd:YAG laser and AH Plus showed the best results.
Asunto(s)
Láseres de Semiconductores , Láseres de Estado Sólido , Cementos de Resina , Materiales de Obturación del Conducto Radicular , Preparación del Conducto Radicular/instrumentación , Ápice del Diente/efectos de la radiación , Resinas Compuestas , Recubrimiento Dental Adhesivo , Resinas Epoxi , Humanos , Preparación del Conducto Radicular/métodos , Propiedades de Superficie/efectos de la radiación , Ápice del Diente/ultraestructuraRESUMEN
The purpose of this study was to compare, in vitro, by means of computerized analysis of digital radiographic images, the anatomic alterations produced in the mandibular molar tooth dentinal walls of mesiobucal canals with severe curvature by three different endodontic techniques: Progressive Preparation, Staged and Serial Preparation. A selection was made of 45 extracted, human, mandibular molars, with root curvatures greater than 25 degrees. They were divided into three groups for every technique studied, which were then sub-divided into three sub-groups in accordance with the position of the curvature along the root: cervical, median or apical. After access surgery and tooth length determination, the canals were filled with 100% Barium Sulphate radiological contrast and the teeth were then radiographed with a direct digital radiography system, using a special apparatus capable of keeping the samples in the same spatial position during the different radiographic takes. After the above-mentioned endodontic techniques had been performed, the teeth were again filled with Barium sulphate and were also radiographed under the same previously mentioned conditions. The pre- and post-operative digital images were then analyzed in two computerized programs, AutoCAD 2004 and CorelDraw 10, to assess, respectively, the areas and the horizontal alterations which occurred in the internal and external walls of the root canals. The results indicated that although no significant differences among the techniques were shown in the statistical analysis, in a descriptive analysis the Progressive Preparation technique was shown to be more regular, uniform and effective.