RESUMEN

Fish collagen peptide (FCP) is a water-soluble polymer with easy accessibility, bioactivity, and reactivity due to its solubility. The gelation of FCP can be carried out by chemical crosslinking, but the mechanical strength of FCP hydrogel is very low because of its intrinsically low molecular weight. Therefore, the mechanical properties of FCP gel should be improved for its wider application as a biomaterial. In this study, we investigated the mechanical properties of M-FCP gel in the context of understanding the influence of chitin nanofibers (CHNFs) on FCP hydrogels. FCP with a number average molecular weight (Mn) of ca. 5000 was reacted with glycidyl methacrylate (GMA) and used for the preparation of photocrosslinked hydrogels. Subsequently, composite hydrogels of methacrylate-modified FCP (M-FCP) and CHNF were prepared by the photoirradiation of a solution of M-FCP containing dispersed CHNF at an intensity of ~60 mW/cm2 for 450 s in the presence of 2-hydroxy-1-[4-(hydroxyethoxy)phenyl]-2-methyl-1-propanone (Irgacure 2959) as a photoinitiator. Compression and tensile tests of the FCP hydrogels were carried out using a universal tester. The compression and tensile strength of the hydrogel increased 10-fold and 4-fold, respectively, by the addition of 0.6% CHNF (20% M-FCP), and Young's modulus increased 2.5-fold (20% M-FCP). The highest compression strength of the M-FCP/CHNF hydrogel was ~300 kPa. Cell proliferation tests using fibroblast cells revealed that the hydrogel with CHNF showed good cell compatibility. The cells showed good adhesion on the M-FCP gel with CHNF, and the growth of fibroblast cells after 7 days was higher on the M-FCP/CHNF gel than on the M-FCP gel without CHNF. In conclusion, we found that CHNF improved the mechanical properties as well as the fibroblast cell compatibility, indicating that M-FCP hydrogels reinforced with CHNF are useful as scaffolds and wound-dressing materials.

RESUMEN

Addition of the silylated tag (STag) enables peptides to be highly soluble in CPME, allowing them to be used at high concentrations in a coupling reaction to enhance reactivity and achieve effective synthesis of sterically hindered peptides. We described the development of a continuous one-pot STag-assisted peptide synthesis platform as a method that provides near-stoichiometric, speedy, environmentally friendly, and scalable peptide synthesis.

Asunto(s)

RESUMEN

α-Emission radiotherapeutics has potential to be one of most effective cancer therapeutics. Herein, we report a facile synthesis of an 211At-labeled immunoconjugate for use as an α-emission molecular targeting therapy. We synthesized a tetrazine probe modified with closo-decaborate(2-), a prosthetic group that forms a bioavailable stable complex with 211At. Our one-pot three-component double-click labeling method was used to attach decaborate to trastuzumab (anti-HER2 antibody) using decaborate-tetrazine and TCO-aldehyde probes without reducing the antibody binding affinity. Labeling the decaborate-attached trastuzumab with 211At produced in the cyclotron at the RIKEN Nishina Center, at which highly radioactive 211At can be produced, readily furnished the 211At-labeled trastuzumab with a maximum specific activity of 15 MBq µg-1 and retention of the native binding affinity. Intratumor injection of the 211At-labeled trastuzumab in BALB/c nude mice implanted with HER2-expressing epidermoid cancer cells yielded efficient accumulation at the targeted tumor site as well as effective suppression of tumor growth.

RESUMEN

Biocompatibility of cinnamoyl-modified carbohydrate materials is not well-known, while they are attracting attention as a photoreactive material. In order to investigate biocompatible properties of cinnamoyl-modified carbohydrate, hydroxypropyl cellulose (HPC) was reacted with cinnamoyl chloride to yield cinnamoyl-modified HPC (HPC-C) for a cell proliferation test. HPC-Cs with three different degrees of substitution (DS) were prepared by changing a feed ratio of cinnamoyl chloride to HPC. The DS of the products ranged from 1.3 to 3.0 per one hydroxylpropyl anhydroglucose unit. Thermal analysis using DSC and TGA showed that the HPC-C with higher DS has a glass transition temperature and higher thermal stability. Ultraviolet (UV) light was irradiated on the HPC-C thin films, and changes in the UV-vis spectrum of the films were examined. In the course of UV irradiation, the absorbance at 280 nm was reduced. Fibroblast cells were cultured on the photocrosslinked HPC-C films, and cell growth was examined. The cell proliferation test revealed that the photocrosslinked HPC-C films have good compatibility with fibroblast cells.

RESUMEN

A one-pot three-component double-click process for preparing tumor-targeting agents for cancer radiotherapy is described here. By utilizing DOTA (or NOTA) containing tetrazines and the TCO-substituted aldehyde, the two click reactions, the tetrazine ligation (an inverse electron-demand Diels-Alder cycloaddition) and the RIKEN click (a rapid 6π-azaelectrocyclization), could simultaneously proceed under mild conditions to afford covalent attachment of the metal chelator DOTA or NOTA to biomolecules such as to albumin and anti-IGSF4 antibody without altering their activities. Subsequently, radiolabeling of DOTA- or NOTA-attached albumin and anti-IGSF4 antibody (an anti-tumor-targeting antibody) with [67Cu], a ß--emitting radionuclide, could be achieved in a highly efficient manner via a simple chelation with DOTA proving to be a more superior chelator than NOTA. Our work provides a new and operationally simple method for introducing the [67Cu] isotope even in large quantities to biomolecules, thereby representing an important process for preparations of clinically relevant tumor-targeting agents for radiotherapy.

Asunto(s)

RESUMEN

A photocrosslinkable trehalose derivative carrying mesogenic groups was synthesized by esterification reactions. The derivative (TC-HBPHA) was synthesized by the reaction of partially cinnamoyl-modified trehalose (TC4) with 4-(4-hexyloxybenzoyloxy)phenoxy-6-oxohexanoic acid (HBPHA) as a mesogenic unit. TC-HBPHA showed a nematic liquid crystalline mesophase at a temperature range from 150 °C to 175 °C in the heating process under observation with a polarized optical microscope. The dimerization of the cinnamoyl groups of TC-HBPHA by ultraviolet (UV) light irradiation was monitored by ultraviolet-visible (UV-Vis) spectroscopy and Fourier transform infrared (FT-IR) spectroscopy. The photocrosslinked film was obtained after the UV irradiation of TC-HBPHA, and it kept the liquid crystalline mesophase at almost the same temperature range. Fibroblast cells cultured on the photocrosslinked TC-HBPHA proliferated as well as on the polystyrene culture plate, indicating that the film has no toxicity. Interestingly, some cells on photocrosslinked TC-HBPHA had a spindle shape and aligned characteristically.

RESUMEN

Photocrosslinked hydrogels reinforced by microfibrillated cellulose (MFC) were prepared from a methacrylate-functionalized fish elastin polypeptide and MFC dispersed in dimethylsulfoxide (DMSO). First, a water-soluble elastin peptide with a molecular weight of ca. 500 g/mol from the fish bulbus arteriosus was polymerized by N,N'-dicyclohexylcarbodiimide (DCC), a condensation reagent, and then modified with 2-isocyanatoethyl methacrylate (MOI) to yield a photocrosslinkable fish elastin polypeptide. The product was dissolved in DMSO and irradiated with UV light in the presence of a radical photoinitiator. We obtained hydrogels successfully by substitution of DMSO with water. The composite gel with MFC was prepared by UV irradiation of the photocrosslinkable elastin polypeptide mixed with dispersed MFC in DMSO, followed by substitution of DMSO with water. The tensile test of the composite gels revealed that the addition of MFC improved the tensile properties, and the shape of the stress-strain curve of the composite gel became more similar to the typical shape of an elastic material with an increase of MFC content. The rheology measurement showed that the elastic modulus of the composite gel increased with an increase of MFC content. The cell proliferation test on the composite gel showed no toxicity.

Asunto(s)

RESUMEN

We assessed the stability of orthodontic mini-implants in young rats. Male rats with mean ages of 6 weeks (n = 16) and 20 weeks (n = 16) were divided into four groups (n = 8 each). In the 6- and 20-week immediate-loading groups, immediately after placement, mini-implants were exposed to an experimental traction force for 2 weeks. In the 6- and 20-week healing groups, the force was applied for 2 weeks after a 6-week healing period. Right tibiae served as the test limbs and the left tibiae as controls. A Periotest device was used to measure mini-implant mobility after traction, and Tukey's test was used to compare Periotest values among groups. The results showed significantly greater mobility in the 6-week immediate-loading group than in the 20-week immediate-loading and 6- and 20-week healing groups, and significantly less mobility in the 6-week healing group than in the 20-week immediate-loading group (P < 0.05). Mini-implants were stable during the healing period. The results indicate that mini-implants can be used for orthodontic anchorage in juvenile patients if the duration of healing is sufficient.

Asunto(s)

RESUMEN

Bi(1-x)Gd(x)FeO3 (0 < or = x < or = 1.0) nanoparticles were synthesized by a wet chemical method. The annealing temperatures were controlled to obtain single-phase Bi(1-x)Gd(x)FeO3 nanoparticles. The crystal diameters decreased as the number of doped Gd ions increased. The crystal structure changed, as the number of Gd ions increased, from rhombohedral to orthorhombic perovskite, at x = 0.2. The behavior of the magnetization curves observed at various values of x (x = 0.05, 0.1, 0.15) of the rhombohedral structure suggested that the canted antiferromagnetism and remanent magnetization (M(r)) drastically increased, compared with those at x = 0 (BiFeO3). It is suggested that the spin-canting angle of the Fe ions increased with the increase in the number of Gd ions. The dielectric properties at x = 0.1 showed that the dielectric loss (tan delta) was improved, compared with that at x = 0 (BiFeO3), by approximately 90%, while the real part of the dielectric constant epsilon' was reduced by approximately 15%. The reason is that the doping impurities restrained the reduction in the leakage current. It was found, from the X-ray absorption fine structure (XAFS) spectra, that Gd ions were doped accurately and that the symmetry of the B site was improved. The Mössbauer analysis suggested the existence of magnetic cycloid spiral ordering.

RESUMEN

CuMnO2 nanoparticles with diameters of 64 nm were synthesized by a novel wet chemical method. An optimized two-step annealing method was developed through the analysis of thermogravimetric differential thermal analysis (TG-DTA) measurements in order to obtain single-phase CuMnO2. A sharp exothermic peak was observed in the DTA curve at approximately 500 K where structural changes of the copper oxides and manganese oxides in the precursor are expected to occur. It is believed that Cu+ ions were oxidized to Cu2+ ions and that Mn2+ ions were oxidized to Mn3+ ions in the Cu-Mn-O system. Deoxidization reactions were also found at approximately 1200 K. The optimized annealing temperature for the first step was determined to be 623 K in air. The optimized annealing temperature for the second step was 1173 K in an Ar atmosphere. Magnetization measurements suggested an antiferromagnetic spin ordering at approximately 50 K. It was expected that Mn3+ spin interactions induced magnetic phase transition affected by definite temperature.

RESUMEN

We examined the receptor-mediated effects of extracellular ATP on neuronal differentiation of PC12 cells, Neuro2a cells and MEB5 cells by using a series of receptor antagonists. The P2Y13 receptor antagonist MRS2211 significantly accelerated neurite outgrowth in all cases. Treatment with nerve growth factor (NGF) alone activated ERK1/2 in PC12 cells, and the activation was further increased by MRS2211. These results suggest involvement of P2Y13 receptor in suppression of neuronal differentiation. Thus, P2Y13 receptor antagonists might be candidates for treatment of neurodegenerative diseases.

Asunto(s)

RESUMEN

One notable complication of mini-implants that are used to provide anchorage in orthodontic treatment is loosening. The aim of this study was to evaluate the relationship between mini-implant mobility during the healing phase and the prognosis for implant stability. Twenty male Wistar rats (aged 20 weeks) were used. Drills with diameters of 0.8, 0.9, 1.0, and 1.1 mm were used to make pilot holes in the rat tibiae. The inserted mini-implants (diameter 1.4 mm; spearhead 1.2 mm; halfway between maximum and minimum 1.3 mm; length 4.0 mm) were subjected to an experimental traction of force for 3 weeks. Bone-to-implant contact (BIC) was observed histologically. Another 20 male rats (aged 20 weeks) underwent an identical procedure, and the stability of the mini-implants was measured using the Periotest before and after traction. The data were statistically analysed using Scheffé's test. The BIC ratios of the 0.9 and 1.0 mm groups were significantly greater than those of the other groups. The Periotest values measured 3 weeks after implant insertion were significantly lower (P < 0.05) than those measured at insertion, except in the 1.1 mm group. To obtain mini-implant stability, the hole diameter should be between 69 and 77 per cent of the diameter of the mini-implant. A significant decrease in the mobility of the mini-implants 3 weeks post-insertion implies a good prognosis for the subsequent mini-implant stability.

Asunto(s)

RESUMEN

Two well-known antifungals, amphotericin B (AmB) and amphodinol 3 (AM3), are thought to exert antifungal activity by forming ion-permeable channels or pores together with sterol molecules. However, detailed molecular recognitions for AmB-sterol and AM3-sterol in lipid bilayers have yet to be determined. Toward (19)F NMR-based investigation of the molecular recognition underlying their potent antifungal activity, we synthesized 6-fluoro-ergosterol in five steps via ring opening of (5α,6α)-epoxide of ergosterol acetate with using novel combination of TiF(4) and n-Bu(4)N(+)Ph(3)SiF(2)(-). Then we evaluated its activity of promoting pore formation of AmB and AM3, and found that pore formation of AmB was barely promoted by 6-F-ergosterol in clear contrast to the dramatic promotion effect of unmodified ergosterol, whereas AM3 activity was markedly enhanced in the presence of 6-F-ergosterol, which was comparable to that of unmodified ergosterol. These results indicate that the introduction of an F atom at C6 position of ergosterol plays an inhibitory role in interacting with AmB, but it is not the case with AM3.

Asunto(s)

RESUMEN

The aim of this study was to investigate the initial stability of tapered orthodontic miniscrews (T-type screws) after placement, the necessity of a healing period, and the propriety of immediate loading. Twenty male Wistar rats with a mean age of 20 weeks were divided into two groups. In the immediate-loading groups, straight orthodontic miniscrews (S-type screws) and T-type screws (five rats each) underwent experimental traction force for 2 weeks (W) immediately after placement. In the healing groups (S- and T-type, five rats each), force was applied for 2 W after a 6-W healing period. The right tibia in each rat was identified as the test limb, while the left tibia in each rat was used as the control group, and underwent no experimental force during the experimental period. The screw-to-bone contact was observed histologically and the bone-screw contact ratio was calculated. Scheffe's test was performed to compare the bone-screw contact ratio in each group using statistical software package (SPSS 8.0 for Windows). In the control group, the bone-screw contact ratio improved from 34.8 +/- 16.0 to 74.8 +/- 12.0 per cent with S-type screws in proportion to the experimental period (2 to 8 W, respectively). With the T-type screws in the test group, there was no significant difference between the immediate-loading and healing groups. In the immediate-loading group, the bone-screw contact ratio with T-type screws was significantly greater (82.3 +/- 15.0 per cent) than with the S-type screws (33.3 +/- 11.8 per cent; P < 0.05), suggesting that T-type screws can be used for orthodontic anchorage immediately after placement.

Asunto(s)

RESUMEN

The biomechanical influences of primary factors on titanium mini-implant, which is used as an anchorage for orthodontic tooth movement, were quantified using the three-dimensional finite element method. Six types of finite element models were designed to show various thread pitches from 0.5 to 1.5 mm. Three models were designed with abutment and three other models without abutment. A traction force of 2 N was applied to the head of the mini-implant or abutment to be at 45 degrees to the bone surface. No remarkable differences were observed in the stress distribution patterns regardless of thread pitch variance. However, the stress distribution was remarkably different between models with abutment and without abutment. The maximum stress of the model with abutment and thread pitch 0.5 mm was the least as compared with the other models. Areas of high-level stress were obviously smaller than in the models without abutment. The plots of the displacement distributions of the models with abutment also presented significant pattern differences as compared with the models without abutment. The high-level area was localized to the head of the implant and the abutment in models with abutment. Therefore, the existence of the abutment is significantly useful in decreasing the stress concentration on the bone, while the effect of thread pitch was uncertain.

Asunto(s)

RESUMEN

In recent years, mandibular expansion has been increasingly performed in conjunction with orthodontic treatment. Lateral tipping of the molars associated with mandibular expansion should, however, be considered, because excessive expansion may result in excessive buccal tooth inclination, which may disturb the occlusal relationship. This study was conducted to quantitatively clarify molar movement during mandibular expansion using the Schwarz appliance to determine the permissible limit of mandibular expansion as a clinical index for inclination movement. Inclinations in the masticatory surface of the first molar and intermolar width were measured before expansion (T1), after expansion (T2), and before edgewise treatment (T3). Lower plaster models from 29 subjects treated with expansion plates were used and compared with models from 11 control subjects with normal occlusion. The average treatment change (T1-T2) in intermolar width was 5.42 mm (standard deviation 1.98), and the average angle of buccal tooth inclination was 10.16 degrees (standard deviation 3.83). No significant correlation was found between age prior to treatment and the treatment period when they were compared with the intermolar width increments and inclination angles. There was a significant positive correlation between retention duration and the amount of expansion. The regression coefficient of the angle of buccal tooth inclination during expansion to the increment of the intermolar width was approximately 0.2. This means that 1 mm of expansion is accompanied by 5 degrees of molar lateral tipping. This coefficient is clinically useful for estimating the permissible limit for mandibular expansion.

Asunto(s)

RESUMEN

The effects of YM337, the Fab fragment of a humanized anti-glycoprotein IIb/IIIa (GPIIb/IIIa) monoclonal antibody C4G1, on in vitro platelet function and binding properties were compared with those of abciximab, the Fab fragment of the human/murine chimeric anti-GPIIb/IIIa monoclonal antibody 7E3. Both agents completely inhibited platelet aggregation caused by all agonists tested except ristocetin. Further, both inhibited human platelet adhesion to von Willebrand factor, fibrinogen, fibronectin and subendothelial matrix with similar potency. Fibrinogen binding to washed platelets was dose-dependently inhibited by both agents. In binding assay using 125I-YM337 and 125I-abciximab, Kd values determined with platelet-rich plasma were 6.74 +/- 0.56 nM for YM337 and 6.65 +/- 1.45 nM for abciximab, and the number of binding sites were 42,700 +/- 3,000 for YM337 and 76,000 +/- 5,400 for abciximab. GPIIb/IIIa was precipitated from the solubilized fraction of platelets by both agents. In contrast, integrin alphavbeta3 was precipitated from the solubilized fraction of human umbilical vein endothelial cells by abciximab but not by YM337. Fibrinogen binding to purified GPIIb/IIIa was dose-dependently inhibited by both agents. In contrast, vitronectin binding to purified integrin alphavbeta3 was dose-dependently inhibited by abciximab but not by YM337, supporting the idea that abciximab reacts to integrin alphavbeta3. Therefore, YM337 was suggested to bind to a different epitope of GPIIb/IIIa from abciximab. These results suggest that YM337 specifically acts on platelet GPIIb/IIIa receptors and has similar inhibitory properties on platelet aggregation and platelet adhesion to abciximab.

Asunto(s)