RESUMEN
PURPOSE: To observe the formation of canal aberrations in S-shaped root canals prepared by every file of hand-used ProTaper. METHODS: Fifteen S-shaped simulated resin root canals were selected. Each root canal was prepared by every file of hand-used ProTaper following the manufacturer instruction. The images of canals prepared by S1, S2, F1, F2 and F3 were taken and stored, which were divided into group S1, S2, F1, F2 and F3. One image of canal unprepared was superposed with the images of the same root canal in these five groups respectively to observe the types and number of canal aberrations, which included unprepared area, danger zone, ledge, elbow, zip and perforation. SPSS12.0 software pakage was used for Fisher's exact probabilities in 2x2 table. RESULTS: Unprepared area decreased following preparation by every file of ProTaper, but it still existed when the canal preparation was finished. The incidence of danger zone, elbow and zip in group F1 was 15/15, 11/15, 4/15, respectively, which was significantly higher than that in group S2(2/15,0,0) (P<0.001). Ledge appeared after prepared by F2, and increased sharply in group F3. None perforation was found in all groups. CONCLUSIONS: The incidence of canal aberrations begins to increase after prepared by finishing files of ProTaper.The presence of unprepared area suggests that it is essential to rinse canal abundantly during complicated canal preparation and canal antisepsis after preparation.
Asunto(s)
Cavidad Pulpar , Níquel , Humanos , Preparación del Conducto Radicular , TitanioRESUMEN
OBJECTIVE: To investigate the influence of sealer placement on apical sealability in root canal treatment. METHODS: 100 extracted single root canal teeth were selected. All canals were prepared by manual Protaper instrument in a step-back way. The samples were divided into 5 groups randomly. A group: 30 samples, sealer placement by chief gutta percha; B group: 30 samples, sealer placement by K file; C group: 30 samples, sealer placement by spreader; D group: 5 samples, a positive control; E group: 5 samples, a negative control. There were 2 subsets in each experimental group which were obturated by lateral gutta percha with or without sealer. Glucose oxidase method was used to measure the apical leakage at the 1st 2nd, 4th, 7th, 10th, 15th, 20th, 25th, 30th day of the experiment. RESULTS: Apical sealability varied with different sealer placement methods (F=4.832, P=0.001). Sealer placement by chief gutta percha (A group) had the best instant apical sealability. However, lateral gutta percha with or without sealer didn't affect the apical sealibility. CONCLUSION: Placing the same kind sealer in different ways can affect the apical sealability. There were no significant differences of the apical leakage no matter the lateral gutta percha with or without sealer. In order to get better instant apical sealability and simplify the clinic operation, placing the sealer with a chief gutta percha while the lateral gutta percha without sealer is recommended.
Asunto(s)
Cavidad Pulpar , Obturación del Conducto Radicular , Filtración Dental , Gutapercha , Humanos , Preparación del Conducto Radicular , Cemento de Óxido de Zinc-EugenolRESUMEN
OBJECTIVE: To evaluate the stability of biomechanics of occipitoatlantoaxial reconstruction with transarticular screw fixation. METHODS: Twelve fresh human cadaveric occipitocervical spine specimens were mounted in a custom-designed, spine-testing machine that applied pure moments while recording the three-dimensional angular movement at occiput (Oc)-C(1) and C(1 - 2) segments. The specimens were tested under seven different conditions: the intact (intact group), the occipitoatlantoaxial instability (Destabilized group), fixation with Ti-cable plus bone graft group (cable + graf group), fixation with the transarticular fixation (CTS group), fixation with SUMMIT occitocervical spinal fixation system (SUMMIT group), fixation with transarticular screw plus bone graft (CTS + graf group), and fixation with SMMIT system and plus graft group (SUMMIT + graf group). The data obtained were statistically analyzed. RESULTS: The CTS group reduced motion to well within the normal rang. In the Oc-C(1) segment, The CTS group and SUMMIT group allowed a very small rang of motion (ROM) and neutral zone (NZ) during lateral bending and axial rotation. The ROM and NZ during flexion and extension of the SUMMIT group, were significantly smaller than those of cable + graf group and CTS group (6.64 degrees +/- 0.59 degrees, 2.49 degrees +/- 0.26 degrees, 0.50 degrees +/- 0.03 degrees, 0.21 degrees +/- 0.01 degrees, 0.27 degrees +/- 0.07 degrees, 0.13 degrees +/- 0.01 degrees vs 10.01 degrees +/- 1.26 degrees, 3.80 degrees +/- 0.79 degrees, 7.93 degrees +/- 1.34 degrees, 3.18 degrees +/- 0.95 degrees, 9.54 degrees +/- 0.87 degrees, 5.93 degrees +/- 0.74 degrees, P < 0.05). In the C(1 - 2) segment, ROM and NZ in all directions of CTS group were smaller in rotation than SUMMIT group (1.64 degrees +/- 0.39 degrees, 0.61 degrees +/- 0.15 degrees, 0.14 degrees +/- 0.05 degrees, 0.02 degrees +/- 0.01 degrees, 0.32 degrees +/- 0.04 degrees, 0.08 degrees +/- 0.01 degrees, vs 0.21 degrees +/- 0.04 degrees, 0.07 degrees +/- 0.03 degrees, 0.21 degrees +/- 0.12 degrees, 0.10 degrees +/- 0.02 degrees, 2.92 degrees +/- 0.28 degrees, 1.27 degrees +/- 0.11 degrees, all P < 0.05). There was no significant difference in ROM and NZ in all directions between CTS + graf group and SUMMIT + Graf group (P > 0.05). CONCLUSION: In vivo biomechanics studies show that posterior occipitocervical transarticular fixation has unique features in reconstructing dynamic stability of the occipitoatlantoaxis, especially in controlling stability of rotation and lateral flexion, thus ensuring successful fusion of the implanted bone and allowing for clinical use of the technique.