RESUMEN
The influence of wastewater treatment plant (WWTP) effluents from one microelectronic industrial zone on element concentrations and partitioning in river water was investigated. The stepwise membrane filtration is used to distinguish different size fractions including large particulate (>18 µm), particulate (0.2-18 µm), colloidal/nanoparticle (10 kDa-0.2 µm) and truly dissolved fractions (<10 kDa) in river water samples and WWTP effluents. Results demonstrated that anthropogenic inputs (WWTP effluents and industrial area) had an important influence on concentrations and partitioning of some elements in river water. Mass balance results showed that membrane filtration processes could realize a good fractionation for many elements (good recoveries) in water samples. Flux decline during 0.2 µm and 10 kDa filtrations were analyzed, and corresponding fouling mechanisms are discussed.
Asunto(s)
Material Particulado/análisis , Ríos/química , Contaminantes Químicos del Agua/análisis , Purificación del Agua/métodos , Aluminio/análisis , Coloides/análisis , Conductividad Eléctrica , Filtración/métodos , Filtración/normas , Francia , Concentración de Iones de Hidrógeno , Hierro/análisis , Membranas Artificiales , Modelos Químicos , Nanopartículas/análisis , Material Particulado/clasificación , Selenio/análisis , Silicio/análisis , Titanio/análisis , Vanadio/análisis , Aguas Residuales/química , Contaminantes Químicos del Agua/clasificación , Purificación del Agua/normasRESUMEN
Membrane separation processes have become a basic unit operation for process design and product development. These processes are used in a variety of separation and concentration steps, but in all cases, the membranes must be cleaned regularly to remove both organic and inorganic material deposited on the surface and/or into the membrane bulk. Cleaning/disinfection is a vital step in maintaining the permeability and selectivity of the membrane in order to get the plant to its original capacity, to minimize risks of bacteriological contamination, and to make acceptable products. For this purpose, a large number of chemical cleaning/disinfection agents are commercially available. In general, these cleaning/disinfection agents have to improve the membrane flux to a certain extent. However, they can also cause irreversible damages in membrane properties and performances over the long term. Until now, there is considerably less literature dedicated to membrane ageing than to cleaning/disinfection. The knowledge in cleaning/disinfection efficiency has recently been improved. But in order to develop optimized cleaning/disinfection protocols there still remains a challenge to better understand membrane ageing. In order to compensate for the lack of correlated cleaning/disinfection and ageing data from the literature, this paper investigates cleaning/disinfection efficiencies and ageing damages of organic ultrafiltration membranes. The final aim is to provide less detrimental cleaning/disinfection procedures and to propose some guidelines which should have been taken into consideration in term of membrane ageing studies. To carry out this study, this article will detail the background of cleaning/disinfection and aging membrane topics in a first introductive part. In a second part, key factors and endpoints of cleaning/disinfection and aging membranes will be discussed deeply: the membrane role and the cleaning parameters roles, such as water quality, storing conditions, cleaning/disinfection/aging agents/conditions/protocols. The third and last part will be developed the parameters, methods and ways of characterization at our disposal and commonly used to develop and implement membrane cleaning and/or ageing studies.
Asunto(s)
Desinfección/métodos , Membranas Artificiales , Ultrafiltración/instrumentación , Factores de TiempoRESUMEN
Low-pressure membrane systems, including microfiltration (MF) and ultrafiltration (UF) membranes, are being increasingly used in drinking water treatments due to their high level of pathogen removal. However, the pathogen will pass through the membrane and contaminate the product if the membrane integrity is compromised. Therefore, an effective on-line integrity monitoring method for MF and UF membrane systems is essential to guarantee the regulatory requirements for pathogen removal. A lot of works on low-pressure membrane integrity tests have been conducted by many researchers. This paper provides a literature review about different low-pressure membrane integrity monitoring methods for the drinking water treatment, including direct methods (pressure-based tests, acoustic sensor test, liquid porosimetry, etc.) and indirect methods (particle counting, particle monitoring, turbidity monitoring, surrogate challenge tests). Additionally, some information about the operation of membrane integrity tests is presented here. It can be realized from this review that it remains urgent to develop an alternative on-line detection technique for a quick, accurate, simple, continuous and relatively inexpensive evaluation of low-pressure membrane integrity. To better satisfy regulatory requirements for drinking water treatments, the characteristic of this ideal membrane integrity test is proposed at the end of this paper.