RESUMEN

The formation of coarse primary Si is the main scientific challenge faced in the preparation of high-Si Al matrix composites. The SiC/Al-50Si composites are prepared by high pressure solidification, which allows the primary Si to form a SiC-Si spherical microstructure with SiC, while the solubility of Si in Al is increased by high pressure to reduce the proportion of primary Si, thus enhancing the strength of the composites. The results show that the high melt viscosity under high pressure makes the SiC particles almost "fixed" in situ. The SEM analysis shows that the presence of SiC in the growth front of the primary Si will hinder its continued growth and eventually form SiC-Si spherical microstructure. Through aging treatment, a large number of dispersed nanoscale Si phases are precipitated in the α-Al supersaturated solid solution. The TEM analysis shows that a semi-coherent interface is formed between the α-Al matrix and the nanoscale Si precipitates. The three-point bending tests shows that the bending strength of the aged SiC/Al-50Si composites prepared at 3 GPa is 387.6 MPa, which is 18.6% higher than that of the unaged composites.

RESUMEN

The microstructure and mechanical properties of SiC/Al-40Si composites prepared under high pressure were studied. As the pressure increases from 1 atm to 3 GPa, the primary Si phase in the Al-40Si alloy is refined. With increasing pressure, the composition of the eutectic point increases, the solute diffusion coefficient decreases exponentially, and the concentration of Si solute at the front of the solid-liquid interface of the primary Si is low, which contributes to the refining of the primary Si and inhibiting its faceted growth. The bending strength of SiC/Al-40Si composite prepared under 3 GPa was 334 MPa, which was 66% higher compared to the Al-40Si alloy prepared under the same pressure.

RESUMEN

In this work, the microstructure and solidification behavior of nickel-based superalloy GTD222 at different cooling rates are studied. The solidification of the superalloy GTD222 proceeds as follows: L → L + γ, L → L + γ + MC, L → L + (γ/γ')-Eutectic and L → η phase. Due to alloying element redistribution, the temperature of the solidus GTD222 superalloy, 1310 °C, is slightly lower than the temperature of the liquidus, which is 1360 °C. It was found that the dendrite arm spacing of the alloy decreased with the increase of the cooling rate from 200 µm at 2.5 K/min to 100 µm at 20 K/min.

RESUMEN

A calcium silicate and calcium phosphate (CaSiO(3)/CaHPO(4)·2H(2)O) composite coating was applied by a chemical reaction to Mg-Zn-Mn-Ca alloy to improve its biocompatiblity. The surface microstructure was observed by scanning electronic microscopy (SEM) and the surface bioactivity was assessed by a cell interaction experiment. SEM observation showed that a microporous layer was formed on the surface of Mg-Zn-Mn-Ca alloy. It was shown by XRD that the reaction layer was mainly composed of CaHPO(4)·2H(2)O and a small amount of CaSiO(3). In vitro cell experiments indicated that osteoblasts showed good adhesion, high growth rates and proliferation characteristics on the coated Mg-Zn-Mn-Ca alloy, indicating that the surface cytocompatibility of Mg-Zn-Mn-Ca alloy was significantly improved by the calcium phosphate coating.

Asunto(s)

RESUMEN

In this work, poly(hydroxybutyrate-co-hydroxyhexanoate) (PHBHHx) film was fabricated by a solution-casting method and subsequently was modified by NaOH treatment to improve the surface hydrophilic property. Surface properties including hydrophilicity, surface appearance and functional groups were characterized by water contact angle measurement, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The results showed the hydrophilicity of PHBHHx film was obviously improved by the NaOH treatment due to the topography changes promoted by the NaOH-etching and the introduction of polar groups included hydroxyl and carboxyl on the topmost surface layers. However, the modified film exhibited an aging effect: the hydrophilicity decreases with time elapsed during storage. It was found that the aging rate was strongly dependent on the crystallinity of the film and the storage environment. The sample with high-crystallinity lost hydrophilic property slower than that with low-crystallinity. Hydrophilic and low-temperature environment also prevented the modified PHBHHx from fast losing of the hydrophilicity.

Asunto(s)