RESUMEN

The development of slippery surfaces has been widely investigated due to their excellent icephobic properties. A distinct kind of an ice-repellent structure known as a slippery liquid-infused porous surface (SLIPS) has recently drawn attention due to its simplicity and efficacy as a passive ice-protection method. These surfaces are well known for exhibiting very low ice adhesion values (τice < 20 kPa). In this study, pure Polytetrafluoroethylene (PTFE) fibers were fabricated using the electrospinning process to produce superhydrophobic (SHS) porous coatings on samples of the aeronautical alloy AA6061-T6. Due to the high fluorine-carbon bond strength, PTFE shows high resistance and chemical inertness to almost all corrosive reagents as well as extreme hydrophobicity and high thermal stability. However, these unique properties make PTFE difficult to process. For this reason, to develop PTFE fibers, the electrospinning technique has been used by an PTFE nanoparticles (nP PTFE) dispersion with addition of a very small amount of polyethylene oxide (PEO) followed with a sintering process (380 °C for 10 min) to melt the nP PTFE together and form uniform fibers. Once the porous matrix of PTFE fibers is attached, lubricating oil is added into the micro/nanoscale structure in the SHS in place of air to create a SLIPS. The experimental results show a high-water contact angle (WCA) ≈ 150° and low roll-off angle (αroll-off) ≈ 22° for SHS porous coating and a decrease in the WCA ≈ 100° and a very low αroll-off ≈ 15° for SLIPS coating. On one hand, ice adhesion centrifuge tests were conducted for two types of icing conditions (glaze and rime) accreted in an ice wind tunnel (IWT), as well as static ice at different ice adhesion centrifuge test facilities in order to compare the results for SHS, SLIPs and reference materials. This is considered a preliminary step in standardization efforts where similar performance are obtained. On the other hand, the ice adhesion results show 65 kPa in the case of SHS and 4.2 kPa of SLIPS for static ice and <10 kPa for rime and glace ice. These results imply a significant improvement in this type of coatings due to the combined effect of fibers PTFE and silicon oil lubricant.

RESUMEN

INTRODUCTION: Tafamidis is the only approved transthyretin stabiliser approved for the treatment of variant transthyretin amyloidosis (A-ATTRv) related polyneuropathy (PNP). The aim of this study is to analyse the effectiveness of tafamidis in a real-world setting in Spain. METHODS: This is a national multicenter study in which patients with V30M A-ATTR related PN treated with tafamidis for at least 1 year were included. Clinical, demographic, analytical and neurophysiological variables were analysed. RESULTS: 100 patients were recruited. Overall, 47 patients (47%) were classified as complete responders, 32 (32%) as partial responders and 21 (21%) as non-responders. The median duration of treatment with tafamidis was 35 months. Better treatment response was shown in patients with in polyneuropathy disability score (PND) I, lower neuropathy impairment score (NIS), compound muscle action potential (CMAP) and Norfolk QoL questionnaire. Higher albumin levels and lower NTproBNP levels were also associated with better treatment response. A basal NIS≥15 predicts that the patient could be a non-responder with a 60% probability. CONCLUSIONS: Our results reinforce the tafamidis efficacy to treat A-ATTRv-PNP if started early in the disease course. Patients with the V30M variant, NIS<15 and PND I are the most appropriate subjects for this treatment.

Asunto(s)

RESUMEN

A superhydrophobic composite coating consisting of polytetrafluoroethylene (PTFE) and poly(acrylic acid)+ ß-cyclodextrin (PAA + ß-CD) was prepared on an aluminum alloy AA 6061T6 substrate by a three-step process of electrospinnig, spin coating, and electrospraying. The electrospinning technique is used for the fabrication of a polymeric binder layer synthesized from PAA + ß-CD. The superhydrophilic characteristic of the electrospun PAA + ß-CD layer makes it suitable for the absorption of an aqueous suspension with PTFE particles in a spin-coating process, obtaining a hydrophobic behavior. Then, the electrospraying of a modified PTFE dispersion forms a layer of distributed PTFE particles, in which a strong bonding of the particles with each other and with the PTFE particles fixed in the PAA + ß-CD fiber matrix results in a remarkable improvement of the particles adhesion to the substrate by different heat treatments. The experimental results corroborate the important role of obtaining hierarchical micro/nano multilevel structures for the optimization of superhydrophobic surfaces, leading to water contact angles above 170°, very low contact angle of hysteresis (CAH = 2°) and roll-off angle (αroll−off < 5°). In addition, a superior corrosion resistance is obtained, generating a barrier to retain the electrolyte infiltration. This study may provide useful insights for a wide range of applications.

RESUMEN

This study described and compared physical activity (PA) characteristics at the end of the human lifespan using conventional cut-point-based versus cut-point-free accelerometer metrics. Eighteen institutionalized centenarians (101.5 ± 2.1 years, 72.2% female, 89% frail) wore the wrist GENEActiv accelerometer for 7 days. Conventional metrics, such as time spent in light-intensity PA (LiPA) and moderate-to-vigorous intensity PA (MVPA) were calculated according to published cut-points for adults and older adults. The following cut-point-free metrics were evaluated: average acceleration, intensity gradient and Mx metrics. Depending on the cut-point, centenarians accumulated a median of 15-132 min/day of LiPA and 3-15 min/day of MVPA. The average acceleration was 9.2 mg [Q1: 6.7 mg-Q3: 12.6 mg] and the intensity gradient was -3.19 [-3.34--3.12]. The distribution of Z-values revealed positive skew for MVPA, indicating a potential floor effect, whereas the skew magnitude was attenuated for cut-point-free metrics such as intensity gradient or M5. However, both cut-point-based and cut-point-free metrics were similarly positively associated with functional independence, cognitive and physical capacities. This is the first time that PA has been described in centenarians using cut-point-free metrics. Our results suggest that new analytical approaches could overcome cut-point limitations when studying the oldest-old. Future studies using these new cut-point-free PA metrics are warranted to provide more complete and comparable information across groups and populations.

Asunto(s)

RESUMEN

Anti-icing or passive strategies have undergone a remarkable growth in importance as a complement for the de-icing approaches or active methods. As a result, many efforts for developing icephobic surfaces have been mostly dedicated to apply superhydrophobic coatings. Recently, a different type of ice-repellent structure based on slippery liquid-infused porous surfaces (SLIPS) has attracted increasing attention for being a simple and effective passive ice protection in a wide range of application areas, especially for the prevention of ice formation on aircrafts. In this work, the electrospinning technique has been used for the deposition of PVDF-HFP coatings on samples of the aeronautical alloy AA7075 by using a thickness control system based on the identification of the proper combination of process parameters such as the flow rate and applied voltage. In addition, the influence of the experimental conditions on the nanofiber properties is evaluated in terms of surface morphology, wettability, corrosion resistance, and optical transmittance. The experimental results showed an improvement in the micro/nanoscale structure, which optimizes the superhydrophobic and anticorrosive behavior due to the air trapped inside the nanotextured surface. In addition, once the best coating was selected, centrifugal ice adhesion tests (CAT) were carried out for two types of icing conditions (glaze and rime) simulated in an ice wind tunnel (IWT) on both as-deposited and liquid-infused coatings (SLIPs). The liquid-infused coatings showed a low water adhesion (low contact angle hysteresis) and low ice adhesion strength, reducing the ice adhesion four times with respect to PTFE (a well-known low-ice-adhesion material used as a reference).

RESUMEN

In this work, a one-step electrospinning technique has been implemented for the design and development of functional surfaces with a desired morphology in terms of wettability and corrosion resistance by using polycaprolactone (PCL) and zinc oxide nanoparticles (ZnO NPs). The surface morphology has been characterized by confocal microscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM) and water contact angle (WCA), whereas the corrosion resistance has been evaluated by Tafel polarization curves. Strict control over the input operational parameters (applied voltage, feeding rate, distance tip to collector), PCL solution concentration and amount of ZnO NPs have been analyzed in depth by showing their key role in the final surface properties. With this goal in mind, a design of experiment (DoE) has been performed in order to evaluate the optimal coating morphology in terms of fiber diameter, surface roughness (Ra), water contact angle (WCA) and corrosion rate. It has been demonstrated that the solution concentration has a significant effect on the resultant electrospun structure obtained on the collector with the formation of beaded fibers with a higher WCA value in comparison with uniform bead-free fibers (dry polymer deposition or fiber-merging aspect). In addition, the presence of ZnO NPs distributed within the electrospun fibers also plays a key role in corrosion resistance, although it also leads to a decrease in the WCA. Finally, this is the first time that an exhaustive analysis by using DoE has been evaluated for PCL/ZnO electrospun fibers with the aim to optimize the surface morphology with the better performance in terms of corrosion resistance and wettability.

RESUMEN

Periodic repolarization dynamics (PRD) is a novel electrocardiographic marker of cardiac repolarization instability with powerful risk stratification capacity for total mortality and sudden cardiac death. Here, we use a time-frequency analysis approach to continuously quantify PRD at rest and during exercise, assess its dependence on heart rate variability (HRV) and characterize the effects of age (young adults/middle-aged adults/older adults), body mass index (non-overweight/overweight) and cardiorespiratory fitness level (fit/unfit). Sixty-six male volunteers performed an exercise test. RR and dT variabilities (RRV, dTV), as well as the fraction of dT variability unrelated to RR variability, were computed based on time-frequency representations. The instantaneous LF power of dT (PdTV), representing the same concept as PRD, and of its RRV-unrelated component (PdTVuRRV) were quantified. dT angle was found to mostly oscillate in the LF band. Overall, 50-70% of PdTV was linearly unrelated to RRV. The onset of exercise caused a sudden increase in PdTV and PdTVuRRV, which returned to pre-exercise levels during recovery. Clustering analysis identified a group of overweight and unfit individuals with significantly higher PdTV and PdTVuRRV values at rest than the rest of the population. Our findings shed new light on the temporal profile of PRD during exercise, its relationship to HRV and the differences in PRD between subjects according to phenotypic characteristics.

Asunto(s)

RESUMEN

Among the various polymeric options employed for the deposition of electrospun coatings, poly(vinylidene fluoride) (PVDF) has been widely investigated thanks to its excellent mechanical properties, high chemical resistance, and good thermal stability. In this work, the electrospinning technique is used for the fabrication of functional PVDF fibers in order to identify and evaluate the influence of the experimental conditions on the nanofiber properties in terms of optical transmittance, wettability, corrosion resistance, and surface morphology. Some of these properties can play a relevant role in the prevention of ice formation in aircrafts. According to this, a matrix of 4 × 4 samples of aluminum alloy AA 6061T6 was successfully coated by controlling two operational input parameters such as the resultant applied voltage (from 10 up to 17.5 KV) and the flow rate (from 800 up to 1400 µL/h) for a fixed polymeric precursor concentration (15 wt.%). The experimental results have shown a multilevel fiber-bead structure where the formation of a fiber mesh directly depends on the selected operational parameters. Several microscopy and surface analysis techniques such as confocal microscopy (CM), field emission scanning electron microscopy (FE-SEM), UV/vis spectroscopy, and water contact angle (WCA) were carried out in order to corroborate the morphology, transmittance, and hydrophobicity of the electrospun fiber composite. Finally, the corrosion behavior was also evaluated by electrochemical tests (Tafel curves measurement), showing that the presence of electrospun PVDF fibers produces a relevant improvement in the resultant corrosion resistance of the coated aluminum alloys.

RESUMEN

This work aims to validate the Polar H7 heart rate (HR) sensor for heart rate variability (HRV) analysis at rest and during various exercise intensities in a cohort of male volunteers with different age, body composition and fitness level. Cluster analysis was carried out to evaluate how these phenotypic characteristics influenced HR and HRV measurements. For this purpose, sixty-seven volunteers performed a test consisting of the following consecutive segments: sitting rest, three submaximal exercise intensities in cycle-ergometer and sitting recovery. The agreement between HRV indices derived from Polar H7 and a simultaneous electrocardiogram (ECG) was assessed using concordance correlation coefficient (CCC). The percentage of subjects not reaching excellent agreement (CCC > 0.90) was higher for high-frequency power (PHF) than for low-frequency power (PLF) of HRV and increased with exercise intensity. A cluster of unfit and not young volunteers with high trunk fat percentage showed the highest error in HRV indices. This study indicates that Polar H7 and ECG were interchangeable at rest. During exercise, HR and PLF showed excellent agreement between devices. However, during the highest exercise intensity, CCC for PHF was lower than 0.90 in as many as 60% of the volunteers. During recovery, HR but not HRV measurements were accurate. As a conclusion, phenotypic differences between subjects can represent one of the causes for disagreement between HR sensors and ECG devices, which should be considered specifically when using Polar H7 and, generally, in the validation of any HR sensor for HRV analysis.

Asunto(s)

RESUMEN

Under the hypothesis that sympathetic control of ventricular repolarization may change once the second ventilatory threshold (VT2) has been reached, a novel methodology for non-invasive VT2 estimation based on the analysis of the T wave from the electrocardiogram (ECG) is proposed, and potential underlying physiological mechanisms are suggested. 25 volunteers (33.4 ± 5.2 years) underwent an incremental power cycle ergometer test (25 W/minute). During the test, respiratory gas exchange and multi-lead ECG were acquired. The former was employed to determine VT2, used here as a reference, whereas the latter was used to compute the temporal profiles of an index of ventricular repolarization instability (dT) and its low-frequency (LF) oscillations (LFdT). The sudden increases observed in dT and LFdT profiles above an established heart rate threshold were employed to derive VT2 estimates, referred to as VT2d T and VT2LF d T , respectively. Estimation errors of -4.7 ± 25.2 W were obtained when considering VT2d T . Errors were lower than the one-minute power increment of 25 W in 68% of the subjects and lower than 50 W in 89.5% of them. When using VT2LF d T , estimation error was of 15.3 ± 32.4 W. Most of the subjects shared common characteristic dT and LFdT profiles, which could be reflecting changes in the autonomic control of ventricular repolarization before and after reaching VT2. The analysis of ventricular repolarization dynamics during exercise allows non-invasive ECG-based estimation of VT2, possibly in relation to changes in the autonomic control of ventricular electrical activity when VT2 is reached.

Asunto(s)

RESUMEN

Centenarians are the paradigm of human extreme longevity and healthy aging, because they have postponed, if not avoided, mayor age-related diseases. The purpose of this study was to investigate potential differences in resting heart rate variability (HRV) between young adults, octogenarians, and centenarians and assess whether HRV variables are predictors of all-cause mortality in centenarians. To this end, three groups of participants: young adults (N = 20; 20.6 ± 2.3 years), octogenarians (N = 18; 84.1 ± 2.6 years), and centenarians (N = 17; 101.9 ± 1.9 years) were monitored for 15 min at rest (seated, without moving or talking) to measure RR intervals, from which HRV was evaluated. Our results showed a clear decrease with age in the main parasympathetic HRV variables, as well as in the standard deviation (SD) of the RR series [SD of normal-to-normal interval (SDNN)] and in low frequency (LF) heart rate (HR) oscillations, although differences between octogenarians and centenarians did not reach statistical significance. In 14 centenarians followed until death, only SDNN showed significant correlation (ρ = 0.536; p = 0.048) with survival prognosis. Additionally, SDNN <19 ms was associated with early mortality (≤1 year) in centenarians (Hazard Ratio = 5.72). In conclusion, HRV indices reflecting parasympathetic outflow as well as SDNN and LF all present an age-related reduction, which could be representative of a natural exhaustion of allostatic systems related to age. Moreover, low SDNN values (<19 ms) could be associated with early mortality in centenarians. HRV seems to play a role in exceptional longevity, which could be accounted for by centenarians' exposome.

RESUMEN

To objectively assess physical activity levels and sedentary behavior in a cohort of Spanish centenarians and their nonagenarian peers. Physical activity and sedentary behavior patterns were objectively measured by an ActiGraph GT3X accelerometer in centenarians (n = 18; 83% women; 100.8 ± 0.8 [100-103] years) and nonagenarians (n = 11; 91% women; 93.3 ± 2.5 [90-98] years). Centenarians showed less counts per minute (17.6 ± 7.1 vs. 46.1 ± 23.7, p = .003, d = 1.851) and steps per day (455 ± 237 vs. 1,249 ± 776, p = .007, d = 1.587) than nonagenarians. The daily number of sedentary breaks was also lower in the former (5.0 ± 1.5 vs. 6.7 ± 2.0, p = .019, d = 0.971). When observing time distribution, the most active day period in both groups was the morning, with a peak between 10:00 and 11:59. This data suggest that the decline in physical activity levels continues to worsen until the end of the human lifespan.

Asunto(s)

RESUMEN

Most food allergy cases are associated with a limited group of allergens. This could be attributed to an increased ability of some foods to sensitize and trigger allergic reactions. However, there are no validated animal models to evaluate the sensitizing or allergenic potentials of proteins. Our aim was to evaluate three protocols of adjuvant-free intraperitoneal sensitization that differ in the time points for sample collection (days 14, 28 and 35 from beginning of the sensitization) and also in the number of immunizations (2, 5 and 3, respectively). Ovalbumin (OVA; 0.05 mg), cow milk proteins (CMP; 0.025, 0.05 and 0.25 mg), and potato acid phosphatase (PAP; low allergenic protein; 250.0 mg) were administered intraperitoneally (ip) to BALB/c mice (n = 4⁻6) and the protein-specific IgE and IgG antibody responses were evaluated using ELISA. Additional serum protein-specific IgE antibodies evaluations were carried out after IgG depletion. Anti-OVA IgE antibodies were detected in mice from all three protocols. The responses were higher in the group of mice that underwent the 28-day protocol than in those that underwent the 14- or 35-day protocols (p < 0.01 and p < 0.05, respectively). Anti-CMP IgE antibodies were detected in both the 14- and 28-day protocols, but the response was higher in the group that underwent the 28-day protocol (p < 0.001). The anti-CMP IgE antibody response detection was improved after serum IgG depletion (p < 0.001). Anti-PAP IgE antibodies were not detected. Mice with undetectable serum levels of protein-specific IgE triggered anti-OVA, -CMP, and -PAP IgG responses. An adjuvant-free 28-day protocol with five ip immunizations seems appropriate for evaluation of the inherent sensitizing or allergenic capacity of the studied proteins. Reproducible results were obtained utilizing the BALB/c mouse strain. Inter-laboratory studies including a larger number of proteins should be carried out to validate this model.

Asunto(s)

RESUMEN

The "pancarcinoma" Tn antigen (αGalNAc-O-Ser/Thr) is a tumor-associated carbohydrate antigen (TACA) overexpressed on the surface of cancer cells and suitable target for anticancer vaccines. However, TACAs commonly show weak immunogenicity, low in vivo stability, and poor bioavailability. To address these issues, the development of physiologically stable TACA synthetic mimetics and novel nanocarriers for multivalent display are object of intense research. Nanomaterials represent suitable scaffolds to multimerize antigens, but absence of toxicity, easy functionalization and capability to incorporate biomolecules are compulsory characteristics for vaccine nanocarriers. Here, we report on the conjugation of a synthetic Tn-antigen mimetic to biocompatible and water-dispersible dextran-based single-chain nanoparticles (DXT-SCPNs). In vitro stimulation of PBMCs and analysis of interleukins production indicated a specific innate immune modulation mediated by the multivalent presentation of the Tn mimetic at the nanoparticle surface. These preliminary results pave the way for the development of Tn-mimetic clusters on biocompatible DXT-SCPN for TACA-based vaccines.

Asunto(s)

RESUMEN

Introducción: posterior al tratamiento erradicador de Helicobacter pylori (H. pylori), podría presentarse recurrencia de infección debido a recrudescencia o reinfección. El objetivo de este estudio fue determinar la recurrencia de infección por H. pylori e identificar cepas virulentas de H. pylori al año posterior de su erradicación con terapia triple estándar. Material y métodos: se realizó un estudio cuasiexperimental. La población estudiada fueron pacientes con enfermedades digestivas asociadas a H. pylori que recibieron terapia triple estándar. Todos los pacientes antes del tratamiento erradicador, y solo aquellos pacientes con prueba de aliento con carbono 14 positivo un año posterior al tratamiento se les realizaron cultivos y reacción en cadena de la polimerasa (PCR) de biopsias gástricas para identificación de cepas. Se realizó análisis estadístico mediante el test t de Student y prueba exacta de Fisher, con un nivel de significancia de 0,05. Resultados: se revisaron 128 pacientes, 51 (39,8%) hombres y 77 (60,2%) mujeres, con una edad promedio de 54,8 (DE 13,8) años. Se halló recurrencia anual de infección por H. pylori en 12 (9,3%) pacientes y reinfección y recrudescencia anual en nueve (7%) y tres (2,3%) pacientes respectivamente. La tasa de recrudescencia en proteína antigénica (cagA) fue de 1/30 (3,3%) pacientes y en citotoxina vacuolizante (vacA) fue de 2/112 (1,8%) pacientes. La tasa de reinfección en cagA fue 3/30 (10%) pacientes y en vacA 6/112 (5,3%) pacientes. Conclusiones: en este estudio la recurrencia de infección fue mayor que en países desarrollados con baja prevalencia de H. pylori y menor que en países en vías de desarrollo con mayor prevalencia de H. pylori. Las cepas cagA o vacA s2/m2 fueron aisladas en reinfección y recrudescencia (AU)

Background. After eradication treatment for Helicobacter pylori, infection could recur due to recrudescence or re-infection. The objective of this study was to determine the recurrence of Helicobacter pylori infection and identify virulent Helicobacter pylori strains one year after eradication with standard triple therapy. Material and methods. A quasi-experimental study was performed that included a patient population with digestive diseases associated with Helicobacter pylori who had received standard triple therapy. Cultures and Polymerase Chain Reaction was performed on gastric biopsies for strain identification in all patients prior to eradication treatment and those with a positive carbon 14 breath test one year after eradication treatment. Statistical analysis was performed using the student T test and Fisher’s exact test, statistical significance was set at 0.05. Results. 128 patients were studied, 51 (39.8%) were male and 77 (60.2%) were female with an average age of 54.8 years (DE 13.8). There was an annual recurrence of Helicobacter pylori infection in 12 (9.3%) patients. An annual re-infection and recrudescence occurred in 9 (7 %) and 3 (2.3%) patients respectively. The recrudescence rate for cagA was 1/30 (3.3%) patients and 2/112 (1.8%) patients for vacA. The re-infection rate for cagA was 3/30 (10%) patients and 6/112 (5.3%) patients for vacA. Conclusions. The recurrence of infection in this study was higher than that recorded in developed countries with a low prevalence of H. pylori and lower than that recorded in developing countries with a higher prevalence of H. pylori. The cagA or vacA s2/m2 strains were isolated after re-infection and recrudescence (AU)

Asunto(s)

RESUMEN

BACKGROUND: After eradication treatment for Helicobacter pylori, infection could recur due to recrudescence or re-infection. The objective of this study was to determine the recurrence of Helicobacter pylori infection and identify virulent Helicobacter pylori strains one year after eradication with standard triple therapy. MATERIAL AND METHODS: A quasi-experimental study was performed that included a patient population with digestive diseases associated with Helicobacter pylori who had received standard triple therapy. Cultures and Polymerase Chain Reaction was performed on gastric biopsies for strain identification in all patients prior to eradication treatment and those with a positive carbon 14 breath test one year after eradication treatment. Statistical analysis was performed using the student T test and Fisher's exact test, statistical significance was set at 0.05. RESULTS: 128 patients were studied, 51 (39.8%) were male and 77 (60.2%) were female with an average age of 54.8 years (DE 13.8). There was an annual recurrence of Helicobacter pylori infection in 12 (9.3%) patients. An annual re-infection and recrudescence occurred in 9 (7 %) and 3 (2.3%) patients respectively. The recrudescence rate for cagA was 1/30 (3.3%) patients and 2/112 (1.8%) patients for vacA. The re-infection rate for cagA was 3/30 (10%) patients and 6/112 (5.3%) patients for vacA. CONCLUSIONS: The recurrence of infection in this study was higher than that recorded in developed countries with a low prevalence of H. pylori and lower than that recorded in developing countries with a higher prevalence of H. pylori. The cagA or vacA s2/m2 strains were isolated after re-infection and recrudescence.

Asunto(s)

Asunto(s)

RESUMEN

Chia (Salvia hispanica L.) plant is native from southern Mexico and northern Guatemala. Their seeds are a rich source of bioactive compounds which protect consumers against chronic diseases. Germination improves functionality of the seeds due to the increase in the bioactive compounds and associated antioxidant activity. The purpose of this study was to obtain functional flour from germinated chia seeds under optimized conditions with increased antioxidant activity, phenolic compounds, GABA, essential amino acids, and dietary fiber with respect to un-germinated chia seeds. The effect of germination temperature and time (GT = 20-35 °C, Gt = 10-300 h) on protein, lipid, and total phenolic contents (PC, LC, TPC, respectively), and antioxidant activity (AoxA) was analyzed by response surface methodology as optimization tool. Chia seeds were germinated inside plastic trays with absorbent paper moisturized with 50 mL of 100 ppm sodium hypochlorite dissolution. The sprouts were dried (50 °C/8 h) and ground to obtain germinated chia flours (GCF). The prediction models developed for PC, LC, TPC, and AoxA showed high coefficients of determination, demonstrating their adequacy to explain the variations in experimental data. The highest values of PC, LC, TPC, and AoxA were obtained at two different optimal conditions (GT = 21 °C/Gt = 157 h; GT = 33 °C/Gt = 126 h). Optimized germinated chia flours (OGCF) had higher PC, TPC, AoxA, GABA, essential amino acids, calculated protein efficiency ratio (C-PER), and total dietary fiber (TDF) than un-germinated chia seed flour. The OGCF could be utilized as a natural source of proteins, dietary fiber, GABA, and antioxidants in the development of new functional beverages and foods.

Asunto(s)

RESUMEN

The intervertebral discs (IVDs) provide unique flexibility to the spine and exceptional shock absorbing properties under impact. The inner core of the IVD, the nucleus pulposus (NP) is responsible for this adaptive behavior. Herein, we evaluate an injectable, self-healing dynamic hydrogel (DH) based on gold(I)-thiolate/disulfide (Au-S/SS) exchange as NP replacement in a spine motion segment model. For the first time, we report the application of dynamic covalent hydrogels inside biological tissues. The dynamic exchange between Au-S species and disulfide bonds (SS) resulted in self-healing ability and frequency-dependent stiffness of the hydrogel, which was also confirmed in spine motion segments. Injection of preformed DH into nucleotomized IVDs restored the full biomechanical properties of intact IVDs, including the stiffening effect observed at increasing frequencies, which cannot be achieved with conventional covalent hydrogel. DH has the potential to counteract IVD degeneration associated with high frequency vibrations. Self-healing properties, confirmed by rheology studies and macroscopic observation after injection, were required to inject preformed DH, which recovered its mechanical integrity and microstructure to act as an artificial NP. On the other hand, covalent hydrogel did not show any restoration of NP properties as this conventional material suffered irreversible damages after injection, which demonstrates that the dynamic properties are crucial for this application. The persistence of DH in the IVD space following cyclic high-frequency loading, confirmed by tomography after mechanical testing, suggests that this material would have long life span as an injectable NP replacement material.

Asunto(s)